include/configs/imx8qxp_mek.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2018 NXP
   4  */
   5
   6 #ifndef __IMX8QXP_MEK_H
   7 #define __IMX8QXP_MEK_H
   8
   9 #include <linux/sizes.h>
  10 #include <asm/arch/imx-regs.h>
  11
  12 #ifdef CONFIG_SPL_BUILD
  13 #define CONFIG_SPL_TEXT_BASE                            0x0
  14 #define CONFIG_SPL_MAX_SIZE                             (124 * 1024)
  15 #define CONFIG_SYS_MONITOR_LEN                          (1024 * 1024)
  16 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
  17 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR         0x250
  18 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION              0
  19
  20 #define CONFIG_SPL_LDSCRIPT             "arch/arm/cpu/armv8/u-boot-spl.lds"
  21 #define CONFIG_SPL_STACK                0x013E000
  22 #define CONFIG_SPL_BSS_START_ADDR       0x00128000
  23 #define CONFIG_SPL_BSS_MAX_SIZE         0x1000  /* 4 KB */
  24 #define CONFIG_SYS_SPL_MALLOC_START     0x00120000
  25 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x3000  /* 12 KB */
  26 #define CONFIG_SERIAL_LPUART_BASE       0x5a060000
  27 #define CONFIG_SYS_ICACHE_OFF
  28 #define CONFIG_SYS_DCACHE_OFF
  29 #define CONFIG_MALLOC_F_ADDR            0x00120000
  30
  31 #define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE
  32
  33 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
  34
  35 #define CONFIG_OF_EMBED
  36 #endif
  37
  38 #define CONFIG_REMAKE_ELF
  39
  40 #define CONFIG_BOARD_EARLY_INIT_F
  41
  42 /* Flat Device Tree Definitions */
  43 #define CONFIG_OF_BOARD_SETUP
  44
  45 #undef CONFIG_CMD_EXPORTENV
  46 #undef CONFIG_CMD_IMPORTENV
  47 #undef CONFIG_CMD_IMLS
  48
  49 #undef CONFIG_CMD_CRC32
  50 #undef CONFIG_BOOTM_NETBSD
  51
  52 #define CONFIG_FSL_ESDHC
  53 #define CONFIG_FSL_USDHC
  54 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  55 #define USDHC1_BASE_ADDR                0x5B010000
  56 #define USDHC2_BASE_ADDR                0x5B020000
  57 #define CONFIG_SUPPORT_EMMC_BOOT        /* eMMC specific */
  58
  59 #define CONFIG_ENV_OVERWRITE
  60
  61 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  62
  63 /* Initial environment variables */
  64 #define CONFIG_EXTRA_ENV_SETTINGS               \
  65         "script=boot.scr\0" \
  66         "image=Image\0" \
  67         "panel=NULL\0" \
  68         "console=ttyLP0,${baudrate} earlycon=lpuart32,0x5a060000,${baudrate}\0" \
  69         "fdt_addr=0x83000000\0"                 \
  70         "fdt_high=0xffffffffffffffff\0"         \
  71         "boot_fdt=try\0" \
  72         "fdt_file=fsl-imx8qxp-mek.dtb\0" \
  73         "initrd_addr=0x83800000\0"              \
  74         "initrd_high=0xffffffffffffffff\0" \
  75         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
  76         "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
  77         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
  78         "mmcautodetect=yes\0" \
  79         "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
  80         "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
  81         "bootscript=echo Running bootscript from mmc ...; " \
  82                 "source\0" \
  83         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
  84         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
  85         "mmcboot=echo Booting from mmc ...; " \
  86                 "run mmcargs; " \
  87                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
  88                         "if run loadfdt; then " \
  89                                 "booti ${loadaddr} - ${fdt_addr}; " \
  90                         "else " \
  91                                 "echo WARN: Cannot load the DT; " \
  92                         "fi; " \
  93                 "else " \
  94                         "echo wait for boot; " \
  95                 "fi;\0" \
  96         "netargs=setenv bootargs console=${console} " \
  97                 "root=/dev/nfs " \
  98                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
  99         "netboot=echo Booting from net ...; " \
 100                 "run netargs;  " \
 101                 "if test ${ip_dyn} = yes; then " \
 102                         "setenv get_cmd dhcp; " \
 103                 "else " \
 104                         "setenv get_cmd tftp; " \
 105                 "fi; " \
 106                 "${get_cmd} ${loadaddr} ${image}; " \
 107                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 108                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 109                                 "booti ${loadaddr} - ${fdt_addr}; " \
 110                         "else " \
 111                                 "echo WARN: Cannot load the DT; " \
 112                         "fi; " \
 113                 "else " \
 114                         "booti; " \
 115                 "fi;\0"
 116
 117 #define CONFIG_BOOTCOMMAND \
 118            "mmc dev ${mmcdev}; if mmc rescan; then " \
 119                    "if run loadbootscript; then " \
 120                            "run bootscript; " \
 121                    "else " \
 122                            "if run loadimage; then " \
 123                                    "run mmcboot; " \
 124                            "else run netboot; " \
 125                            "fi; " \
 126                    "fi; " \
 127            "else booti ${loadaddr} - ${fdt_addr}; fi"
 128
 129 /* Link Definitions */
 130 #define CONFIG_LOADADDR                 0x80280000
 131
 132 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 133
 134 #define CONFIG_SYS_INIT_SP_ADDR         0x80200000
 135
 136 /* Default environment is in SD */
 137 #define CONFIG_ENV_SIZE                 0x1000
 138 #define CONFIG_ENV_OFFSET               (64 * SZ_64K)
 139 #define CONFIG_SYS_MMC_ENV_PART         0       /* user area */
 140
 141 #define CONFIG_SYS_MMC_IMG_LOAD_PART    1
 142
 143 /* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board */
 144 #define CONFIG_SYS_MMC_ENV_DEV          1   /* USDHC2 */
 145 #define CONFIG_MMCROOT                  "/dev/mmcblk1p2"  /* USDHC2 */
 146 #define CONFIG_SYS_FSL_USDHC_NUM        2
 147
 148 /* Size of malloc() pool */
 149 #define CONFIG_SYS_MALLOC_LEN           ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)
 150
 151 #define CONFIG_SYS_SDRAM_BASE           0x80000000
 152 #define PHYS_SDRAM_1                    0x80000000
 153 #define PHYS_SDRAM_2                    0x880000000
 154 #define PHYS_SDRAM_1_SIZE               0x80000000      /* 2 GB */
 155 /* LPDDR4 board total DDR is 3GB */
 156 #define PHYS_SDRAM_2_SIZE               0x40000000      /* 1 GB */
 157
 158 /* Serial */
 159 #define CONFIG_BAUDRATE                 115200
 160
 161 /* Monitor Command Prompt */
 162 #define CONFIG_HUSH_PARSER
 163 #define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 164 #define CONFIG_SYS_CBSIZE              2048
 165 #define CONFIG_SYS_MAXARGS             64
 166 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 167 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 168                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 169
 170 /* Generic Timer Definitions */
 171 #define COUNTER_FREQUENCY               8000000 /* 8MHz */
 172
 173 #ifndef CONFIG_DM_PCA953X
 174 #define CONFIG_PCA953X
 175 #define CONFIG_CMD_PCA953X
 176 #define CONFIG_CMD_PCA953X_INFO
 177 #endif
 178
 179 /* Networking */
 180 #define CONFIG_FEC_XCV_TYPE             RGMII
 181 #define FEC_QUIRK_ENET_MAC
 182
 183 #endif /* __IMX8QXP_MEK_H */