include/configs/imx8mq_phanbell.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2020 NXP
   4  */
   5
   6 #ifndef __IMX8M_PHANBELL_H
   7 #define __IMX8M_PHANBELL_H
   8
   9 #include <linux/sizes.h>
  10 #include <asm/arch/imx-regs.h>
  11
  12 #define CONFIG_SPL_MAX_SIZE             (172 * 1024)
  13 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
  14 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
  15 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
  16 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
  17
  18 #ifdef CONFIG_SPL_BUILD
  19 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
  20 #define CONFIG_SPL_WATCHDOG_SUPPORT
  21 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
  22 #define CONFIG_SPL_POWER_SUPPORT
  23 #define CONFIG_SPL_I2C_SUPPORT
  24 #define CONFIG_SPL_LDSCRIPT             "arch/arm/cpu/armv8/u-boot-spl.lds"
  25 #define CONFIG_SPL_STACK                0x187FF0
  26 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  27 #define CONFIG_SPL_LIBGENERIC_SUPPORT
  28 #define CONFIG_SPL_GPIO_SUPPORT
  29 #define CONFIG_SPL_MMC_SUPPORT
  30 #define CONFIG_SPL_BSS_START_ADDR      0x00180000
  31 #define CONFIG_SPL_BSS_MAX_SIZE        0x2000   /* 8 KB */
  32 #define CONFIG_SYS_SPL_MALLOC_START    0x42200000
  33 #define CONFIG_SYS_SPL_MALLOC_SIZE    0x80000   /* 512 KB */
  34 #define CONFIG_SYS_SPL_PTE_RAM_BASE    0x41580000
  35
  36 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
  37 #define CONFIG_MALLOC_F_ADDR            0x182000
  38 /* For RAW image gives a error info not panic */
  39 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
  40
  41 #undef CONFIG_DM_MMC
  42 #undef CONFIG_DM_PMIC
  43 #undef CONFIG_DM_PMIC_PFUZE100
  44
  45 #define CONFIG_SYS_I2C
  46 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  47 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  48 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  49
  50 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  51
  52 #define CONFIG_POWER
  53 #define CONFIG_POWER_I2C
  54 #endif
  55
  56 #define CONFIG_REMAKE_ELF
  57
  58 #define CONFIG_BOARD_EARLY_INIT_F
  59
  60 #undef CONFIG_CMD_EXPORTENV
  61 #undef CONFIG_CMD_IMPORTENV
  62 #undef CONFIG_CMD_IMLS
  63
  64 #undef CONFIG_CMD_CRC32
  65
  66 /* ENET Config */
  67 /* ENET1 */
  68 #if defined(CONFIG_CMD_NET)
  69 #define CONFIG_CMD_PING
  70 #define CONFIG_CMD_DHCP
  71 #define CONFIG_CMD_MII
  72 #define CONFIG_MII
  73 #define CONFIG_ETHPRIME                 "FEC"
  74
  75 #define CONFIG_FEC_MXC
  76 #define CONFIG_FEC_XCV_TYPE             RGMII
  77 #define CONFIG_FEC_MXC_PHYADDR          0
  78 #define FEC_QUIRK_ENET_MAC
  79
  80 #define CONFIG_PHY_GIGE
  81 #define IMX_FEC_BASE                    0x30BE0000
  82
  83 #define CONFIG_PHYLIB
  84 #endif
  85
  86 #define CONFIG_MFG_ENV_SETTINGS \
  87         "initrd_addr=0x43800000\0" \
  88         "initrd_high=0xffffffff\0" \
  89
  90 /* Initial environment variables */
  91 #define CONFIG_EXTRA_ENV_SETTINGS               \
  92         CONFIG_MFG_ENV_SETTINGS \
  93         "script=boot.scr\0" \
  94         "image=Image\0" \
  95         "console=ttymxc0,115200\0" \
  96         "fdt_addr=0x43000000\0"                 \
  97         "fdt_high=0xffffffffffffffff\0"         \
  98         "boot_fdt=try\0" \
  99         "fdt_file=imx8mq-phanbell.dtb\0" \
 100         "initrd_addr=0x43800000\0"              \
 101         "initrd_high=0xffffffffffffffff\0" \
 102         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 103         "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 104         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 105         "mmcautodetect=yes\0" \
 106         "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
 107         "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 108         "bootscript=echo Running bootscript from mmc ...; " \
 109                 "source\0" \
 110         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 111         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 112         "mmcboot=echo Booting from mmc ...; " \
 113                 "run mmcargs; " \
 114                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 115                         "if run loadfdt; then " \
 116                                 "booti ${loadaddr} - ${fdt_addr}; " \
 117                         "else " \
 118                                 "echo WARN: Cannot load the DT; " \
 119                         "fi; " \
 120                 "else " \
 121                         "echo wait for boot; " \
 122                 "fi;\0" \
 123         "netargs=setenv bootargs console=${console} " \
 124                 "root=/dev/nfs " \
 125                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 126         "netboot=echo Booting from net ...; " \
 127                 "run netargs;  " \
 128                 "if test ${ip_dyn} = yes; then " \
 129                         "setenv get_cmd dhcp; " \
 130                 "else " \
 131                         "setenv get_cmd tftp; " \
 132                 "fi; " \
 133                 "${get_cmd} ${loadaddr} ${image}; " \
 134                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 135                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 136                                 "booti ${loadaddr} - ${fdt_addr}; " \
 137                         "else " \
 138                                 "echo WARN: Cannot load the DT; " \
 139                         "fi; " \
 140                 "else " \
 141                         "booti; " \
 142                 "fi;\0"
 143
 144 #define CONFIG_BOOTCOMMAND \
 145            "mmc dev ${mmcdev}; if mmc rescan; then " \
 146                    "if run loadbootscript; then " \
 147                            "run bootscript; " \
 148                    "else " \
 149                            "if run loadimage; then " \
 150                                    "run mmcboot; " \
 151                            "else run netboot; " \
 152                            "fi; " \
 153                    "fi; " \
 154            "else booti ${loadaddr} - ${fdt_addr}; fi"
 155
 156 /* Link Definitions */
 157 #define CONFIG_LOADADDR                 0x40480000
 158
 159 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 160
 161 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
 162 #define CONFIG_SYS_INIT_RAM_SIZE        0x80000
 163 #define CONFIG_SYS_INIT_SP_OFFSET \
 164         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 165 #define CONFIG_SYS_INIT_SP_ADDR \
 166         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 167
 168 #define CONFIG_ENV_OVERWRITE
 169 #define CONFIG_SYS_MMC_ENV_DEV          1   /* USDHC2 */
 170 #define CONFIG_MMCROOT                  "/dev/mmcblk1p2"  /* USDHC2 */
 171
 172 /* Size of malloc() pool */
 173 #define CONFIG_SYS_MALLOC_LEN           ((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)
 174
 175 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 176 #define PHYS_SDRAM                      0x40000000
 177 #define PHYS_SDRAM_SIZE                 0x40000000 /* 1GB DDR */
 178
 179 #define CONFIG_SYS_MEMTEST_START        PHYS_SDRAM
 180 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + \
 181                                         (PHYS_SDRAM_SIZE >> 1))
 182
 183 #define CONFIG_MXC_UART
 184 #define CONFIG_MXC_UART_BASE            UART1_BASE_ADDR
 185
 186 /* Monitor Command Prompt */
 187 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 188 #define CONFIG_SYS_CBSIZE               1024
 189 #define CONFIG_SYS_MAXARGS              64
 190 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 191 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 192                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 193
 194 #define CONFIG_IMX_BOOTAUX
 195
 196 #define CONFIG_CMD_MMC
 197
 198 #define CONFIG_SYS_FSL_USDHC_NUM        2
 199 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
 200
 201 #define CONFIG_SYS_MMC_IMG_LOAD_PART    1
 202
 203 #define CONFIG_MXC_GPIO
 204
 205 #define CONFIG_CMD_FUSE
 206
 207 /* I2C Configs */
 208 #define CONFIG_SYS_I2C_SPEED              100000
 209
 210 #define CONFIG_OF_SYSTEM_SETUP
 211
 212 #ifndef CONFIG_SPL_BUILD
 213 #define CONFIG_DM_PMIC
 214 #endif
 215
 216 #endif