include/configs/cgtqmx6eval.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  *
   4  * Congatec Conga-QEVAl board configuration file.
   5  *
   6  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   7  * Based on Freescale i.MX6Q Sabre Lite board configuration file.
   8  * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
   9  * Leo Sartre, <lsartre@adeneo-embedded.com>
  10  */
  11
  12 #ifndef __CONFIG_CGTQMX6EVAL_H
  13 #define __CONFIG_CGTQMX6EVAL_H
  14
  15 #include "mx6_common.h"
  16
  17 #define CONFIG_MACH_TYPE        4122
  18
  19 #ifdef CONFIG_SPL
  20 #define CONFIG_SYS_SPI_U_BOOT_OFFS      (64 * 1024)
  21 #include "imx6_spl.h"
  22 #endif
  23
  24 /* Size of malloc() pool */
  25 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  26
  27 #define CONFIG_MXC_UART
  28 #define CONFIG_MXC_UART_BASE           UART2_BASE
  29
  30 /* MMC Configs */
  31 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  32
  33 /* SPI NOR */
  34 #define CONFIG_SPI_FLASH_STMICRO
  35 #define CONFIG_SPI_FLASH_SST
  36 #define CONFIG_SF_DEFAULT_BUS           0
  37 #define CONFIG_SF_DEFAULT_SPEED         20000000
  38 #define CONFIG_SF_DEFAULT_MODE          (SPI_MODE_0)
  39
  40 /* Thermal support */
  41 #define CONFIG_IMX_THERMAL
  42
  43 /* I2C Configs */
  44 #define CONFIG_SYS_I2C
  45 #define CONFIG_SYS_I2C_MXC
  46 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  47 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  48 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  49 #define CONFIG_SYS_I2C_SPEED              100000
  50
  51 /* PMIC */
  52 #define CONFIG_POWER
  53 #define CONFIG_POWER_I2C
  54 #define CONFIG_POWER_PFUZE100
  55 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  56
  57 /* USB Configs */
  58 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  59 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  60 #define CONFIG_MXC_USB_FLAGS    0
  61 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
  62
  63 #define CONFIG_USBD_HS
  64
  65 /* Framebuffer */
  66 #define CONFIG_VIDEO_IPUV3
  67 #define CONFIG_VIDEO_BMP_RLE8
  68 #define CONFIG_SPLASH_SCREEN
  69 #define CONFIG_SPLASH_SCREEN_ALIGN
  70 #define CONFIG_BMP_16BPP
  71 #define CONFIG_VIDEO_LOGO
  72 #define CONFIG_VIDEO_BMP_LOGO
  73 #define CONFIG_IMX_HDMI
  74
  75 /* SATA */
  76 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  77 #define CONFIG_DWC_AHSATA_PORT_ID       0
  78 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  79 #define CONFIG_LBA48
  80
  81 /* Ethernet */
  82 #define CONFIG_FEC_MXC
  83 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  84 #define CONFIG_FEC_XCV_TYPE             RGMII
  85 #define CONFIG_ETHPRIME                 "FEC"
  86 #define CONFIG_FEC_MXC_PHYADDR          6
  87 #define CONFIG_PHY_ATHEROS
  88
  89 /* Command definition */
  90
  91 #define CONFIG_MXC_UART_BASE    UART2_BASE
  92 #define CONSOLE_DEV     "ttymxc1"
  93 #define CONFIG_MMCROOT          "/dev/mmcblk0p2"
  94 #define CONFIG_SYS_MMC_ENV_DEV          0
  95
  96 #define CONFIG_EXTRA_ENV_SETTINGS \
  97         "script=boot.scr\0" \
  98         "image=zImage\0" \
  99         "fdtfile=undefined\0" \
 100         "fdt_addr_r=0x18000000\0" \
 101         "boot_fdt=try\0" \
 102         "ip_dyn=yes\0" \
 103         "console=" CONSOLE_DEV "\0" \
 104         "dfuspi=dfu 0 sf 0:0:10000000:0\0" \
 105         "dfu_alt_info_spl=spl raw 0x400\0" \
 106         "dfu_alt_info_img=u-boot raw 0x10000\0" \
 107         "dfu_alt_info=spl raw 0x400\0" \
 108         "bootm_size=0x10000000\0" \
 109         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 110         "mmcpart=1\0" \
 111         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 112         "update_sd_firmware=" \
 113                 "if test ${ip_dyn} = yes; then " \
 114                         "setenv get_cmd dhcp; " \
 115                 "else " \
 116                         "setenv get_cmd tftp; " \
 117                 "fi; " \
 118                 "if mmc dev ${mmcdev}; then "   \
 119                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 120                                 "setexpr fw_sz ${filesize} / 0x200; " \
 121                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 122                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 123                         "fi; "  \
 124                 "fi\0" \
 125         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 126                 "root=${mmcroot}\0" \
 127         "loadbootscript=" \
 128                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 129         "bootscript=echo Running bootscript from mmc ...; " \
 130                 "source\0" \
 131         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 132         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdtfile}\0" \
 133         "mmcboot=echo Booting from mmc ...; " \
 134                 "run mmcargs; " \
 135                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 136                         "if run loadfdt; then " \
 137                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 138                         "else " \
 139                                 "if test ${boot_fdt} = try; then " \
 140                                         "bootz; " \
 141                                 "else " \
 142                                         "echo WARN: Cannot load the DT; " \
 143                                 "fi; " \
 144                         "fi; " \
 145                 "else " \
 146                         "bootz; " \
 147                 "fi;\0" \
 148         "findfdt="\
 149                 "if test $board_rev = MX6Q ; then " \
 150                         "setenv fdtfile imx6q-qmx6.dtb; fi; " \
 151                 "if test $board_rev = MX6DL ; then " \
 152                         "setenv fdtfile imx6dl-qmx6.dtb; fi; " \
 153                 "if test $fdtfile = undefined; then " \
 154                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 155         "netargs=setenv bootargs console=${console},${baudrate} " \
 156                 "root=/dev/nfs " \
 157                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 158         "netboot=echo Booting from net ...; " \
 159                 "run netargs; " \
 160                 "if test ${ip_dyn} = yes; then " \
 161                         "setenv get_cmd dhcp; " \
 162                 "else " \
 163                         "setenv get_cmd tftp; " \
 164                 "fi; " \
 165                 "${get_cmd} ${image}; " \
 166                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 167                         "if ${get_cmd} ${fdt_addr_r} ${fdtfile}; then " \
 168                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 169                         "else " \
 170                                 "if test ${boot_fdt} = try; then " \
 171                                         "bootz; " \
 172                                 "else " \
 173                                         "echo WARN: Cannot load the DT; " \
 174                                 "fi; " \
 175                         "fi; " \
 176                 "else " \
 177                         "bootz; " \
 178                 "fi;\0" \
 179         "spilock=sf probe && sf protect lock 0x3f0000 0x10000;"\
 180
 181 #define CONFIG_BOOTCOMMAND \
 182         "run spilock;"      \
 183         "run findfdt; " \
 184         "mmc dev ${mmcdev};" \
 185         "if mmc rescan; then " \
 186                 "if run loadbootscript; then " \
 187                 "run bootscript; " \
 188                 "else " \
 189                         "if run loadimage; then " \
 190                                 "run mmcboot; " \
 191                         "else run netboot; " \
 192                         "fi; " \
 193                 "fi; " \
 194         "else run netboot; fi"
 195
 196 #define CONFIG_SYS_MEMTEST_START       0x10000000
 197 #define CONFIG_SYS_MEMTEST_END         0x10010000
 198 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 199
 200 /* Physical Memory Map */
 201 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 202
 203 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 204 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 205 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 206
 207 #define CONFIG_SYS_INIT_SP_OFFSET \
 208         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 209 #define CONFIG_SYS_INIT_SP_ADDR \
 210         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 211
 212 /* Environment organization */
 213 #if defined (CONFIG_ENV_IS_IN_MMC)
 214 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 215 #define CONFIG_SYS_MMC_ENV_DEV          0
 216 #endif
 217
 218 #define CONFIG_ENV_SIZE                 (8 * 1024)
 219
 220 #if defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 221 #define CONFIG_ENV_OFFSET               (768 * 1024)
 222 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 223 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 224 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 225 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 226 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 227 #endif
 228
 229 #endif                         /* __CONFIG_CGTQMX6EVAL_H */