include/configs/cgtqmx6eval.h

   1 /*
   2  *
   3  * Congatec Conga-QEVAl board configuration file.
   4  *
   5  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   6  * Based on Freescale i.MX6Q Sabre Lite board configuration file.
   7  * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
   8  * Leo Sartre, <lsartre@adeneo-embedded.com>
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 #ifndef __CONFIG_CGTQMX6EVAL_H
  14 #define __CONFIG_CGTQMX6EVAL_H
  15
  16 #include "mx6_common.h"
  17
  18 #define CONFIG_MACH_TYPE        4122
  19
  20 #ifdef CONFIG_SPL
  21 #define CONFIG_SYS_SPI_U_BOOT_OFFS      (64 * 1024)
  22 #define CONFIG_SPL_SPI_LOAD
  23 #include "imx6_spl.h"
  24 #endif
  25
  26 /* Size of malloc() pool */
  27 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  28
  29 #define CONFIG_BOARD_EARLY_INIT_F
  30 #define CONFIG_MISC_INIT_R
  31
  32 #define CONFIG_MXC_UART
  33 #define CONFIG_MXC_UART_BASE           UART2_BASE
  34
  35 /* MMC Configs */
  36 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  37
  38 /* SPI NOR */
  39 #define CONFIG_SPI_FLASH
  40 #define CONFIG_SPI_FLASH_STMICRO
  41 #define CONFIG_SPI_FLASH_SST
  42 #define CONFIG_MXC_SPI
  43 #define CONFIG_SF_DEFAULT_BUS           0
  44 #define CONFIG_SF_DEFAULT_SPEED         20000000
  45 #define CONFIG_SF_DEFAULT_MODE          (SPI_MODE_0)
  46
  47 /* Miscellaneous commands */
  48 #define CONFIG_CMD_BMODE
  49
  50 /* Thermal support */
  51 #define CONFIG_IMX_THERMAL
  52
  53 /* I2C Configs */
  54 #define CONFIG_SYS_I2C
  55 #define CONFIG_SYS_I2C_MXC
  56 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  57 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  58 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  59 #define CONFIG_SYS_I2C_SPEED              100000
  60
  61 /* PMIC */
  62 #define CONFIG_POWER
  63 #define CONFIG_POWER_I2C
  64 #define CONFIG_POWER_PFUZE100
  65 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  66
  67 /* USB Configs */
  68 #define CONFIG_USB_EHCI
  69 #define CONFIG_USB_EHCI_MX6
  70 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  71 #define CONFIG_USB_HOST_ETHER
  72 #define CONFIG_USB_ETHER_ASIX
  73 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  74 #define CONFIG_MXC_USB_FLAGS    0
  75 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
  76 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
  77
  78 #define CONFIG_USBD_HS
  79
  80 #define CONFIG_USB_FUNCTION_MASS_STORAGE
  81
  82 #define CONFIG_USB_FUNCTION_FASTBOOT
  83 #define CONFIG_CMD_FASTBOOT
  84 #define CONFIG_ANDROID_BOOT_IMAGE
  85 #define CONFIG_FASTBOOT_BUF_ADDR   CONFIG_SYS_LOAD_ADDR
  86 #define CONFIG_FASTBOOT_BUF_SIZE   0x07000000
  87
  88 /* Framebuffer */
  89 #define CONFIG_VIDEO_IPUV3
  90 #define CONFIG_VIDEO_BMP_RLE8
  91 #define CONFIG_SPLASH_SCREEN
  92 #define CONFIG_SPLASH_SCREEN_ALIGN
  93 #define CONFIG_BMP_16BPP
  94 #define CONFIG_VIDEO_LOGO
  95 #define CONFIG_VIDEO_BMP_LOGO
  96 #ifdef CONFIG_MX6DL
  97 #define CONFIG_IPUV3_CLK 198000000
  98 #else
  99 #define CONFIG_IPUV3_CLK 264000000
 100 #endif
 101 #define CONFIG_IMX_HDMI
 102
 103 /* SATA */
 104 #define CONFIG_CMD_SATA
 105 #define CONFIG_DWC_AHSATA
 106 #define CONFIG_SYS_SATA_MAX_DEVICE      1
 107 #define CONFIG_DWC_AHSATA_PORT_ID       0
 108 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
 109 #define CONFIG_LBA48
 110 #define CONFIG_LIBATA
 111
 112 /* Ethernet */
 113 #define CONFIG_FEC_MXC
 114 #define CONFIG_MII
 115 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 116 #define CONFIG_FEC_XCV_TYPE             RGMII
 117 #define CONFIG_ETHPRIME                 "FEC"
 118 #define CONFIG_FEC_MXC_PHYADDR          6
 119 #define CONFIG_PHYLIB
 120 #define CONFIG_PHY_ATHEROS
 121
 122 /* Command definition */
 123
 124 #define CONFIG_MXC_UART_BASE    UART2_BASE
 125 #define CONSOLE_DEV     "ttymxc1"
 126 #define CONFIG_MMCROOT          "/dev/mmcblk0p2"
 127 #define CONFIG_SYS_MMC_ENV_DEV          0
 128
 129 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 130 #define CONFIG_EXTRA_ENV_SETTINGS \
 131         "script=boot.scr\0" \
 132         "image=zImage\0" \
 133         "fdtfile=undefined\0" \
 134         "fdt_addr_r=0x18000000\0" \
 135         "boot_fdt=try\0" \
 136         "ip_dyn=yes\0" \
 137         "console=" CONSOLE_DEV "\0" \
 138         "dfuspi=dfu 0 sf 0:0:10000000:0\0" \
 139         "dfu_alt_info_spl=spl raw 0x400\0" \
 140         "dfu_alt_info_img=u-boot raw 0x10000\0" \
 141         "dfu_alt_info=spl raw 0x400\0" \
 142         "bootm_size=0x10000000\0" \
 143         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 144         "mmcpart=1\0" \
 145         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 146         "update_sd_firmware=" \
 147                 "if test ${ip_dyn} = yes; then " \
 148                         "setenv get_cmd dhcp; " \
 149                 "else " \
 150                         "setenv get_cmd tftp; " \
 151                 "fi; " \
 152                 "if mmc dev ${mmcdev}; then "   \
 153                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 154                                 "setexpr fw_sz ${filesize} / 0x200; " \
 155                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 156                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 157                         "fi; "  \
 158                 "fi\0" \
 159         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 160                 "root=${mmcroot}\0" \
 161         "loadbootscript=" \
 162                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 163         "bootscript=echo Running bootscript from mmc ...; " \
 164                 "source\0" \
 165         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 166         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdtfile}\0" \
 167         "mmcboot=echo Booting from mmc ...; " \
 168                 "run mmcargs; " \
 169                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 170                         "if run loadfdt; then " \
 171                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 172                         "else " \
 173                                 "if test ${boot_fdt} = try; then " \
 174                                         "bootz; " \
 175                                 "else " \
 176                                         "echo WARN: Cannot load the DT; " \
 177                                 "fi; " \
 178                         "fi; " \
 179                 "else " \
 180                         "bootz; " \
 181                 "fi;\0" \
 182         "findfdt="\
 183                 "if test $board_rev = MX6Q ; then " \
 184                         "setenv fdtfile imx6q-qmx6.dtb; fi; " \
 185                 "if test $board_rev = MX6DL ; then " \
 186                         "setenv fdtfile imx6dl-qmx6.dtb; fi; " \
 187                 "if test $fdtfile = undefined; then " \
 188                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 189         "netargs=setenv bootargs console=${console},${baudrate} " \
 190                 "root=/dev/nfs " \
 191                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 192         "netboot=echo Booting from net ...; " \
 193                 "run netargs; " \
 194                 "if test ${ip_dyn} = yes; then " \
 195                         "setenv get_cmd dhcp; " \
 196                 "else " \
 197                         "setenv get_cmd tftp; " \
 198                 "fi; " \
 199                 "${get_cmd} ${image}; " \
 200                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 201                         "if ${get_cmd} ${fdt_addr_r} ${fdtfile}; then " \
 202                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 203                         "else " \
 204                                 "if test ${boot_fdt} = try; then " \
 205                                         "bootz; " \
 206                                 "else " \
 207                                         "echo WARN: Cannot load the DT; " \
 208                                 "fi; " \
 209                         "fi; " \
 210                 "else " \
 211                         "bootz; " \
 212                 "fi;\0" \
 213         "spilock=sf probe && sf protect lock 0x3f0000 0x10000;"\
 214
 215 #define CONFIG_BOOTCOMMAND \
 216         "run spilock;"      \
 217         "run findfdt; " \
 218         "mmc dev ${mmcdev};" \
 219         "if mmc rescan; then " \
 220                 "if run loadbootscript; then " \
 221                 "run bootscript; " \
 222                 "else " \
 223                         "if run loadimage; then " \
 224                                 "run mmcboot; " \
 225                         "else run netboot; " \
 226                         "fi; " \
 227                 "fi; " \
 228         "else run netboot; fi"
 229
 230 #define CONFIG_SYS_MEMTEST_START       0x10000000
 231 #define CONFIG_SYS_MEMTEST_END         0x10010000
 232 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 233
 234 /* Physical Memory Map */
 235 #define CONFIG_NR_DRAM_BANKS           1
 236 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 237
 238 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 239 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 240 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 241
 242 #define CONFIG_SYS_INIT_SP_OFFSET \
 243         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 244 #define CONFIG_SYS_INIT_SP_ADDR \
 245         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 246
 247 /* Environment organization */
 248 #if defined (CONFIG_ENV_IS_IN_MMC)
 249 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 250 #define CONFIG_SYS_MMC_ENV_DEV          0
 251 #endif
 252
 253 #define CONFIG_ENV_SIZE                 (8 * 1024)
 254
 255 #define CONFIG_ENV_IS_IN_SPI_FLASH
 256 #if defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 257 #define CONFIG_ENV_OFFSET               (768 * 1024)
 258 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 259 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 260 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 261 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 262 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 263 #endif
 264
 265 #endif                         /* __CONFIG_CGTQMX6EVAL_H */