sunxi: Add support for using MII phy-s with the GMAC nic
[oweals/u-boot.git] / include / configs / at91sam9m10g45ek.h
1 /*
2  * (C) Copyright 2007-2008
3  * Stelian Pop <stelian@popies.net>
4  * Lead Tech Design <www.leadtechdesign.com>
5  *
6  * Configuation settings for the AT91SAM9M10G45EK board(and AT91SAM9G45EKES).
7  *
8  * SPDX-License-Identifier:     GPL-2.0+
9  */
10
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13
14 #include <asm/hardware.h>
15
16 #define CONFIG_SYS_TEXT_BASE            0x73f00000
17
18 #define CONFIG_ATMEL_LEGACY             /* required until (g)pio is fixed */
19
20 /* ARM asynchronous clock */
21 #define CONFIG_SYS_AT91_SLOW_CLOCK      32768
22 #define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
23
24 #define CONFIG_AT91SAM9M10G45EK
25
26 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs      */
27 #define CONFIG_SETUP_MEMORY_TAGS
28 #define CONFIG_INITRD_TAG
29 #define CONFIG_SKIP_LOWLEVEL_INIT
30 #define CONFIG_BOARD_EARLY_INIT_F
31 #define CONFIG_DISPLAY_CPUINFO
32
33 #define CONFIG_CMD_BOOTZ
34 #define CONFIG_OF_LIBFDT
35
36 #define CONFIG_SYS_GENERIC_BOARD
37
38 /* general purpose I/O */
39 #define CONFIG_ATMEL_LEGACY             /* required until (g)pio is fixed */
40 #define CONFIG_AT91_GPIO
41 #define CONFIG_AT91_GPIO_PULLUP 1       /* keep pullups on peripheral pins */
42
43 /* serial console */
44 #define CONFIG_ATMEL_USART
45 #define CONFIG_USART_BASE               ATMEL_BASE_DBGU
46 #define CONFIG_USART_ID                 ATMEL_ID_SYS
47
48 /* LCD */
49 #define CONFIG_LCD
50 #define LCD_BPP                         LCD_COLOR8
51 #define CONFIG_LCD_LOGO
52 #undef LCD_TEST_PATTERN
53 #define CONFIG_LCD_INFO
54 #define CONFIG_LCD_INFO_BELOW_LOGO
55 #define CONFIG_SYS_WHITE_ON_BLACK
56 #define CONFIG_ATMEL_LCD
57 #define CONFIG_ATMEL_LCD_RGB565
58 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
59 /* board specific(not enough SRAM) */
60 #define CONFIG_AT91SAM9G45_LCD_BASE             0x73E00000
61
62 /* LED */
63 #define CONFIG_AT91_LED
64 #define CONFIG_RED_LED          AT91_PIN_PD31   /* this is the user1 led */
65 #define CONFIG_GREEN_LED        AT91_PIN_PD0    /* this is the user2 led */
66
67 #define CONFIG_BOOTDELAY        3
68
69 /*
70  * BOOTP options
71  */
72 #define CONFIG_BOOTP_BOOTFILESIZE
73 #define CONFIG_BOOTP_BOOTPATH
74 #define CONFIG_BOOTP_GATEWAY
75 #define CONFIG_BOOTP_HOSTNAME
76
77 /*
78  * Command line configuration.
79  */
80
81 /* No NOR flash */
82 #define CONFIG_SYS_NO_FLASH
83
84 #include <config_cmd_default.h>
85 #undef CONFIG_CMD_BDI
86 #undef CONFIG_CMD_FPGA
87 #undef CONFIG_CMD_IMI
88 #undef CONFIG_CMD_IMLS
89 #undef CONFIG_CMD_LOADS
90
91 #define CONFIG_CMD_PING
92 #define CONFIG_CMD_DHCP
93 #define CONFIG_CMD_NAND
94 #define CONFIG_CMD_USB
95
96 /* SDRAM */
97 #define CONFIG_NR_DRAM_BANKS            1
98 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_CS6
99 #define CONFIG_SYS_SDRAM_SIZE           0x08000000
100
101 #define CONFIG_SYS_INIT_SP_ADDR \
102         (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
103
104 /* NAND flash */
105 #ifdef CONFIG_CMD_NAND
106 #define CONFIG_NAND_ATMEL
107 #define CONFIG_SYS_MAX_NAND_DEVICE              1
108 #define CONFIG_SYS_NAND_BASE                    ATMEL_BASE_CS3
109 #define CONFIG_SYS_NAND_DBW_8
110 /* our ALE is AD21 */
111 #define CONFIG_SYS_NAND_MASK_ALE                (1 << 21)
112 /* our CLE is AD22 */
113 #define CONFIG_SYS_NAND_MASK_CLE                (1 << 22)
114 #define CONFIG_SYS_NAND_ENABLE_PIN              AT91_PIN_PC14
115 #define CONFIG_SYS_NAND_READY_PIN               AT91_PIN_PC8
116
117 #endif
118
119 /* MMC */
120 #define CONFIG_CMD_MMC
121
122 #ifdef CONFIG_CMD_MMC
123 #define CONFIG_MMC
124 #define CONFIG_GENERIC_MMC
125 #define CONFIG_GENERIC_ATMEL_MCI
126 #endif
127
128 #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
129 #define CONFIG_CMD_FAT
130 #define CONFIG_DOS_PARTITION
131 #endif
132
133 /* Ethernet */
134 #define CONFIG_MACB
135 #define CONFIG_RMII
136 #define CONFIG_NET_RETRY_COUNT          20
137 #define CONFIG_RESET_PHY_R
138 #define CONFIG_AT91_WANTS_COMMON_PHY
139
140 /* USB */
141 #define CONFIG_USB_EHCI
142 #define CONFIG_USB_EHCI_ATMEL
143 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS      2
144 #define CONFIG_USB_STORAGE
145
146 #define CONFIG_SYS_LOAD_ADDR            0x22000000      /* load address */
147
148 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
149 #define CONFIG_SYS_MEMTEST_END          0x23e00000
150
151 #ifdef CONFIG_SYS_USE_NANDFLASH
152 /* bootstrap + u-boot + env in nandflash */
153 #define CONFIG_ENV_IS_IN_NAND
154 #define CONFIG_ENV_OFFSET               0xc0000
155 #define CONFIG_ENV_OFFSET_REDUND        0x100000
156 #define CONFIG_ENV_SIZE                 0x20000
157
158 #define CONFIG_BOOTCOMMAND                                              \
159         "nand read 0x70000000 0x200000 0x300000;"                       \
160         "bootm 0x70000000"
161 #define CONFIG_BOOTARGS                                                 \
162         "console=ttyS0,115200 earlyprintk "                             \
163         "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,"          \
164         "256k(env),256k(env_redundant),256k(spare),"                    \
165         "512k(dtb),6M(kernel)ro,-(rootfs) "                             \
166         "root=/dev/mtdblock7 rw rootfstype=jffs2"
167 #elif CONFIG_SYS_USE_MMC
168 /* bootstrap + u-boot + env + linux in mmc */
169 #define FAT_ENV_INTERFACE       "mmc"
170 #define FAT_ENV_DEVICE          0
171 #define FAT_ENV_PART            1
172 #define FAT_ENV_FILE            "uboot.env"
173 #define CONFIG_ENV_IS_IN_FAT
174 #define CONFIG_FAT_WRITE
175 #define CONFIG_ENV_SIZE         0x4000
176
177 #define CONFIG_BOOTARGS         "console=ttyS0,115200 " \
178                                 "mtdparts=atmel_nand:" \
179                                 "8M(bootstrap/uboot/kernel)ro,-(rootfs) " \
180                                 "root=/dev/mmcblk0p2 rw rootwait"
181 #define CONFIG_BOOTCOMMAND      "fatload mmc 0:1 0x71000000 dtb; " \
182                                 "fatload mmc 0:1 0x72000000 zImage; " \
183                                 "bootz 0x72000000 - 0x71000000"
184 #endif
185
186 #define CONFIG_BAUDRATE                 115200
187
188 #define CONFIG_SYS_PROMPT               "U-Boot> "
189 #define CONFIG_SYS_CBSIZE               256
190 #define CONFIG_SYS_MAXARGS              16
191 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
192 #define CONFIG_SYS_LONGHELP
193 #define CONFIG_CMDLINE_EDITING
194 #define CONFIG_AUTO_COMPLETE
195 #define CONFIG_SYS_HUSH_PARSER
196
197 /*
198  * Size of malloc() pool
199  */
200 #define CONFIG_SYS_MALLOC_LEN           ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
201
202 #endif