Merge branch 'master' of git://www.denx.de/git/u-boot-imx
[oweals/u-boot.git] / include / configs / advantech_dms-ba16.h
1 /*
2  * Copyright (C) 2016 Timesys Corporation
3  * Copyright (C) 2016 Advantech Corporation
4  * Copyright (C) 2012 Freescale Semiconductor, Inc.
5  *
6  * SPDX-License-Identifier:     GPL-2.0+
7  */
8
9 #ifndef __ADVANTECH_DMSBA16_CONFIG_H
10 #define __ADVANTECH_DMSBA16_CONFIG_H
11
12 #include <asm/arch/imx-regs.h>
13 #include <asm/imx-common/gpio.h>
14
15 #define CONFIG_BOARD_NAME       "Advantech DMS-BA16"
16
17 #define CONFIG_MXC_UART_BASE    UART4_BASE
18 #define CONSOLE_DEV     "ttymxc3"
19 #define CONFIG_EXTRA_BOOTARGS   "panic=10"
20
21 #define CONFIG_BOOT_DIR ""
22 #define CONFIG_LOADCMD "fatload"
23 #define CONFIG_RFSPART "2"
24
25 #define CONFIG_SUPPORT_EMMC_BOOT
26
27 #include "mx6_common.h"
28 #include <linux/sizes.h>
29
30 #define CONFIG_CMDLINE_TAG
31 #define CONFIG_SETUP_MEMORY_TAGS
32 #define CONFIG_INITRD_TAG
33 #define CONFIG_REVISION_TAG
34 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
35
36 #define CONFIG_BOARD_EARLY_INIT_F
37 #define CONFIG_BOARD_LATE_INIT
38
39 #define CONFIG_MXC_GPIO
40 #define CONFIG_MXC_UART
41
42 #define CONFIG_CMD_FUSE
43 #define CONFIG_MXC_OCOTP
44
45 /* SATA Configs */
46 #define CONFIG_CMD_SATA
47 #define CONFIG_DWC_AHSATA
48 #define CONFIG_SYS_SATA_MAX_DEVICE      1
49 #define CONFIG_DWC_AHSATA_PORT_ID       0
50 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
51 #define CONFIG_LBA48
52 #define CONFIG_LIBATA
53
54 /* MMC Configs */
55 #define CONFIG_FSL_ESDHC
56 #define CONFIG_FSL_USDHC
57 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
58 #define CONFIG_MMC
59 #define CONFIG_GENERIC_MMC
60 #define CONFIG_BOUNCE_BUFFER
61 #define CONFIG_DOS_PARTITION
62
63 /* USB Configs */
64 #define CONFIG_USB_EHCI
65 #define CONFIG_USB_EHCI_MX6
66 #define CONFIG_USB_STORAGE
67 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
68 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
69 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
70 #define CONFIG_MXC_USB_FLAGS    0
71 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
72
73 #define CONFIG_USBD_HS
74 #define CONFIG_USB_FUNCTION_MASS_STORAGE
75 #define CONFIG_USB_GADGET_VBUS_DRAW 2
76
77 /* Networking Configs */
78 #define CONFIG_FEC_MXC
79 #define CONFIG_MII
80 #define IMX_FEC_BASE                    ENET_BASE_ADDR
81 #define CONFIG_FEC_XCV_TYPE             RGMII
82 #define CONFIG_ETHPRIME         "FEC"
83 #define CONFIG_FEC_MXC_PHYADDR          4
84 #define CONFIG_PHYLIB
85 #define CONFIG_PHY_ATHEROS
86
87 /* Serial Flash */
88 #ifdef CONFIG_CMD_SF
89 #define CONFIG_MXC_SPI
90 #define CONFIG_SF_DEFAULT_BUS           0
91 #define CONFIG_SF_DEFAULT_CS            0
92 #define CONFIG_SF_DEFAULT_SPEED 20000000
93 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
94 #endif
95
96 /* allow to overwrite serial and ethaddr */
97 #define CONFIG_ENV_OVERWRITE
98 #define CONFIG_CONS_INDEX       1
99 #define CONFIG_BAUDRATE 115200
100
101 /* Command definition */
102 #define CONFIG_CMD_BMODE
103
104 #define CONFIG_LOADADDR 0x12000000
105 #define CONFIG_SYS_TEXT_BASE    0x17800000
106
107 #define CONFIG_EXTRA_ENV_SETTINGS \
108         "script=boot.scr\0" \
109         "image=" CONFIG_BOOT_DIR "/uImage\0" \
110         "uboot=u-boot.imx\0" \
111         "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
112         "fdt_addr=0x18000000\0" \
113         "boot_fdt=yes\0" \
114         "ip_dyn=yes\0" \
115         "console=" CONSOLE_DEV "\0" \
116         "fdt_high=0xffffffff\0"   \
117         "initrd_high=0xffffffff\0" \
118         "sddev=0\0" \
119         "emmcdev=1\0" \
120         "partnum=1\0" \
121         "loadcmd=" CONFIG_LOADCMD "\0" \
122         "rfspart=" CONFIG_RFSPART "\0" \
123         "update_sd_firmware=" \
124                 "if test ${ip_dyn} = yes; then " \
125                         "setenv get_cmd dhcp; " \
126                 "else " \
127                         "setenv get_cmd tftp; " \
128                 "fi; " \
129                 "if mmc dev ${mmcdev}; then "   \
130                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
131                                 "setexpr fw_sz ${filesize} / 0x200; " \
132                                 "setexpr fw_sz ${fw_sz} + 1; "  \
133                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
134                         "fi; "  \
135                 "fi\0" \
136         "update_sf_uboot=" \
137                 "if tftp $loadaddr $uboot; then " \
138                         "sf probe; " \
139                         "sf erase 0 0xC0000; " \
140                         "sf write $loadaddr 0x400 $filesize; " \
141                         "echo 'U-Boot upgraded. Please reset'; " \
142                 "fi\0" \
143         "setargs=setenv bootargs console=${console},${baudrate} " \
144                 "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
145         "loadbootscript=" \
146                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
147         "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
148                 " source\0" \
149         "loadimage=" \
150                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
151         "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
152         "tryboot=" \
153                 "if run loadbootscript; then " \
154                         "run bootscript; " \
155                 "else " \
156                         "if run loadimage; then " \
157                                 "run doboot; " \
158                         "fi; " \
159                 "fi;\0" \
160         "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
161                 "run setargs; " \
162                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
163                         "if run loadfdt; then " \
164                                 "bootm ${loadaddr} - ${fdt_addr}; " \
165                         "else " \
166                                 "if test ${boot_fdt} = try; then " \
167                                         "bootm; " \
168                                 "else " \
169                                         "echo WARN: Cannot load the DT; " \
170                                 "fi; " \
171                         "fi; " \
172                 "else " \
173                         "bootm; " \
174                 "fi;\0" \
175         "netargs=setenv bootargs console=${console},${baudrate} " \
176                 "root=/dev/nfs " \
177                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
178         "netboot=echo Booting from net ...; " \
179                 "run netargs; " \
180                 "if test ${ip_dyn} = yes; then " \
181                         "setenv get_cmd dhcp; " \
182                 "else " \
183                         "setenv get_cmd tftp; " \
184                 "fi; " \
185                 "${get_cmd} ${image}; " \
186                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
187                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
188                                 "bootm ${loadaddr} - ${fdt_addr}; " \
189                         "else " \
190                                 "if test ${boot_fdt} = try; then " \
191                                         "bootm; " \
192                                 "else " \
193                                         "echo WARN: Cannot load the DT; " \
194                                 "fi; " \
195                         "fi; " \
196                 "else " \
197                         "bootm; " \
198                 "fi;\0" \
199
200 #define CONFIG_BOOTCOMMAND \
201         "usb start; " \
202         "setenv dev usb; " \
203         "setenv devnum 0; " \
204         "setenv rootdev sda${rfspart}; " \
205         "run tryboot; " \
206         \
207         "setenv dev mmc; " \
208         "setenv rootdev mmcblk0p${rfspart}; " \
209         \
210         "setenv devnum ${sddev}; " \
211         "if mmc dev ${devnum}; then " \
212                 "run tryboot; " \
213         "fi; " \
214         \
215         "setenv devnum ${emmcdev}; " \
216         "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
217         "if mmc dev ${devnum}; then " \
218                 "run tryboot; " \
219         "fi; " \
220         \
221         "bmode usb; " \
222
223 #define CONFIG_ARP_TIMEOUT     200UL
224
225 /* Miscellaneous configurable options */
226 #define CONFIG_SYS_LONGHELP
227 #define CONFIG_AUTO_COMPLETE
228
229 /* Print Buffer Size */
230 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
231 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
232
233 #define CONFIG_SYS_MEMTEST_START       0x10000000
234 #define CONFIG_SYS_MEMTEST_END         0x10010000
235 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
236
237 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
238
239 #define CONFIG_CMDLINE_EDITING
240 #define CONFIG_STACKSIZE               (128 * 1024)
241
242 /* Physical Memory Map */
243 #define CONFIG_NR_DRAM_BANKS           1
244 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
245
246 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
247 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
248 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
249
250 #define CONFIG_SYS_INIT_SP_OFFSET \
251         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
252 #define CONFIG_SYS_INIT_SP_ADDR \
253         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
254
255 /* FLASH and environment organization */
256 #define CONFIG_SYS_NO_FLASH
257
258 #define CONFIG_ENV_IS_IN_SPI_FLASH
259 #define CONFIG_ENV_SIZE                 (8 * 1024)
260 #define CONFIG_ENV_OFFSET               (768 * 1024)
261 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
262 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
263 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
264 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
265 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
266
267 #ifndef CONFIG_SYS_DCACHE_OFF
268 #endif
269
270 #define CONFIG_SYS_FSL_USDHC_NUM        3
271
272 /* Framebuffer */
273 #define CONFIG_VIDEO_IPUV3
274 #define CONFIG_VIDEO_BMP_RLE8
275 #define CONFIG_SPLASH_SCREEN
276 #define CONFIG_SPLASH_SCREEN_ALIGN
277 #define CONFIG_BMP_16BPP
278 #define CONFIG_VIDEO_LOGO
279 #define CONFIG_VIDEO_BMP_LOGO
280 #define CONFIG_IPUV3_CLK                260000000
281 #define CONFIG_IMX_HDMI
282 #define CONFIG_IMX_VIDEO_SKIP
283
284 #define CONFIG_PWM_IMX
285 #define CONFIG_IMX6_PWM_PER_CLK         66000000
286
287 #undef CONFIG_CMD_PCI
288 #ifdef CONFIG_CMD_PCI
289 #define CONFIG_PCI_SCAN_SHOW
290 #define CONFIG_PCIE_IMX
291 #define CONFIG_PCIE_IMX_PERST_GPIO      IMX_GPIO_NR(7, 12)
292 #define CONFIG_PCIE_IMX_POWER_GPIO      IMX_GPIO_NR(1, 5)
293 #endif
294
295 /* I2C Configs */
296 #define CONFIG_SYS_I2C
297 #define CONFIG_SYS_I2C_MXC
298 #define CONFIG_SYS_I2C_SPEED            100000
299 #define CONFIG_SYS_I2C_MXC_I2C1
300 #define CONFIG_SYS_I2C_MXC_I2C2
301 #define CONFIG_SYS_I2C_MXC_I2C3
302
303 #endif  /* __ADVANTECH_DMSBA16_CONFIG_H */