include/configs/advantech_dms-ba16.h

   1 /*
   2  * Copyright (C) 2016 Timesys Corporation
   3  * Copyright (C) 2016 Advantech Corporation
   4  * Copyright (C) 2012 Freescale Semiconductor, Inc.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __ADVANTECH_DMSBA16_CONFIG_H
  10 #define __ADVANTECH_DMSBA16_CONFIG_H
  11
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/imx-common/gpio.h>
  14
  15 #define CONFIG_BOARD_NAME       "Advantech DMS-BA16"
  16 #define CONFIG_DEFAULT_FDT_FILE "imx6q-dms-ba16.dtb"
  17
  18 #define CONFIG_MXC_UART_BASE    UART4_BASE
  19 #define CONSOLE_DEV     "ttymxc3"
  20 #define CONFIG_EXTRA_BOOTARGS   "panic=10"
  21
  22 #define CONFIG_BOOT_DIR ""
  23 #define CONFIG_LOADCMD "fatload"
  24 #define CONFIG_RFSPART "2"
  25
  26 #define CONFIG_SUPPORT_EMMC_BOOT
  27
  28 #include "mx6_common.h"
  29 #include <linux/sizes.h>
  30
  31 #define CONFIG_CMDLINE_TAG
  32 #define CONFIG_SETUP_MEMORY_TAGS
  33 #define CONFIG_INITRD_TAG
  34 #define CONFIG_REVISION_TAG
  35 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  36
  37 #define CONFIG_BOARD_EARLY_INIT_F
  38 #define CONFIG_BOARD_LATE_INIT
  39
  40 #define CONFIG_MXC_GPIO
  41 #define CONFIG_MXC_UART
  42
  43 #define CONFIG_CMD_FUSE
  44 #define CONFIG_MXC_OCOTP
  45
  46 /* SATA Configs */
  47 #define CONFIG_CMD_SATA
  48 #define CONFIG_DWC_AHSATA
  49 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  50 #define CONFIG_DWC_AHSATA_PORT_ID       0
  51 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  52 #define CONFIG_LBA48
  53 #define CONFIG_LIBATA
  54
  55 /* MMC Configs */
  56 #define CONFIG_FSL_ESDHC
  57 #define CONFIG_FSL_USDHC
  58 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  59 #define CONFIG_MMC
  60 #define CONFIG_GENERIC_MMC
  61 #define CONFIG_BOUNCE_BUFFER
  62 #define CONFIG_DOS_PARTITION
  63
  64 /* USB Configs */
  65 #define CONFIG_USB_EHCI
  66 #define CONFIG_USB_EHCI_MX6
  67 #define CONFIG_USB_STORAGE
  68 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  69 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  70 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  71 #define CONFIG_MXC_USB_FLAGS    0
  72 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
  73
  74 #define CONFIG_USBD_HS
  75 #define CONFIG_USB_FUNCTION_MASS_STORAGE
  76 #define CONFIG_USB_GADGET_VBUS_DRAW 2
  77
  78 /* Networking Configs */
  79 #define CONFIG_FEC_MXC
  80 #define CONFIG_MII
  81 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  82 #define CONFIG_FEC_XCV_TYPE             RGMII
  83 #define CONFIG_ETHPRIME         "FEC"
  84 #define CONFIG_FEC_MXC_PHYADDR          4
  85 #define CONFIG_PHYLIB
  86 #define CONFIG_PHY_ATHEROS
  87
  88 /* Serial Flash */
  89 #ifdef CONFIG_CMD_SF
  90 #define CONFIG_MXC_SPI
  91 #define CONFIG_SF_DEFAULT_BUS           0
  92 #define CONFIG_SF_DEFAULT_CS            0
  93 #define CONFIG_SF_DEFAULT_SPEED 20000000
  94 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
  95 #endif
  96
  97 /* allow to overwrite serial and ethaddr */
  98 #define CONFIG_ENV_OVERWRITE
  99 #define CONFIG_CONS_INDEX       1
 100 #define CONFIG_BAUDRATE 115200
 101
 102 /* Command definition */
 103 #define CONFIG_CMD_BMODE
 104
 105 #define CONFIG_LOADADDR 0x12000000
 106 #define CONFIG_SYS_TEXT_BASE    0x17800000
 107
 108 #define CONFIG_EXTRA_ENV_SETTINGS \
 109         "script=boot.scr\0" \
 110         "image=" CONFIG_BOOT_DIR "/uImage\0" \
 111         "uboot=u-boot.imx\0" \
 112         "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
 113         "fdt_addr=0x18000000\0" \
 114         "boot_fdt=yes\0" \
 115         "ip_dyn=yes\0" \
 116         "console=" CONSOLE_DEV "\0" \
 117         "fdt_high=0xffffffff\0"   \
 118         "initrd_high=0xffffffff\0" \
 119         "sddev=0\0" \
 120         "emmcdev=1\0" \
 121         "partnum=1\0" \
 122         "loadcmd=" CONFIG_LOADCMD "\0" \
 123         "rfspart=" CONFIG_RFSPART "\0" \
 124         "update_sd_firmware=" \
 125                 "if test ${ip_dyn} = yes; then " \
 126                         "setenv get_cmd dhcp; " \
 127                 "else " \
 128                         "setenv get_cmd tftp; " \
 129                 "fi; " \
 130                 "if mmc dev ${mmcdev}; then "   \
 131                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 132                                 "setexpr fw_sz ${filesize} / 0x200; " \
 133                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 134                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 135                         "fi; "  \
 136                 "fi\0" \
 137         "update_sf_uboot=" \
 138                 "if tftp $loadaddr $uboot; then " \
 139                         "sf probe; " \
 140                         "sf erase 0 0xC0000; " \
 141                         "sf write $loadaddr 0x400 $filesize; " \
 142                         "echo 'U-Boot upgraded. Please reset'; " \
 143                 "fi\0" \
 144         "setargs=setenv bootargs console=${console},${baudrate} " \
 145                 "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
 146         "loadbootscript=" \
 147                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
 148         "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
 149                 " source\0" \
 150         "loadimage=" \
 151                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
 152         "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
 153         "tryboot=" \
 154                 "if run loadbootscript; then " \
 155                         "run bootscript; " \
 156                 "else " \
 157                         "if run loadimage; then " \
 158                                 "run doboot; " \
 159                         "fi; " \
 160                 "fi;\0" \
 161         "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
 162                 "run setargs; " \
 163                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 164                         "if run loadfdt; then " \
 165                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 166                         "else " \
 167                                 "if test ${boot_fdt} = try; then " \
 168                                         "bootm; " \
 169                                 "else " \
 170                                         "echo WARN: Cannot load the DT; " \
 171                                 "fi; " \
 172                         "fi; " \
 173                 "else " \
 174                         "bootm; " \
 175                 "fi;\0" \
 176         "netargs=setenv bootargs console=${console},${baudrate} " \
 177                 "root=/dev/nfs " \
 178                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 179         "netboot=echo Booting from net ...; " \
 180                 "run netargs; " \
 181                 "if test ${ip_dyn} = yes; then " \
 182                         "setenv get_cmd dhcp; " \
 183                 "else " \
 184                         "setenv get_cmd tftp; " \
 185                 "fi; " \
 186                 "${get_cmd} ${image}; " \
 187                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 188                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 189                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 190                         "else " \
 191                                 "if test ${boot_fdt} = try; then " \
 192                                         "bootm; " \
 193                                 "else " \
 194                                         "echo WARN: Cannot load the DT; " \
 195                                 "fi; " \
 196                         "fi; " \
 197                 "else " \
 198                         "bootm; " \
 199                 "fi;\0" \
 200
 201 #define CONFIG_BOOTCOMMAND \
 202         "usb start; " \
 203         "setenv dev usb; " \
 204         "setenv devnum 0; " \
 205         "setenv rootdev sda${rfspart}; " \
 206         "run tryboot; " \
 207         \
 208         "setenv dev mmc; " \
 209         "setenv rootdev mmcblk0p${rfspart}; " \
 210         \
 211         "setenv devnum ${sddev}; " \
 212         "if mmc dev ${devnum}; then " \
 213                 "run tryboot; " \
 214         "fi; " \
 215         \
 216         "setenv devnum ${emmcdev}; " \
 217         "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
 218         "if mmc dev ${devnum}; then " \
 219                 "run tryboot; " \
 220         "fi; " \
 221         \
 222         "bmode usb; " \
 223
 224 #define CONFIG_ARP_TIMEOUT     200UL
 225
 226 /* Miscellaneous configurable options */
 227 #define CONFIG_SYS_LONGHELP
 228 #define CONFIG_AUTO_COMPLETE
 229
 230 /* Print Buffer Size */
 231 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 232 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 233
 234 #define CONFIG_SYS_MEMTEST_START       0x10000000
 235 #define CONFIG_SYS_MEMTEST_END         0x10010000
 236 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 237
 238 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 239
 240 #define CONFIG_CMDLINE_EDITING
 241 #define CONFIG_STACKSIZE               (128 * 1024)
 242
 243 /* Physical Memory Map */
 244 #define CONFIG_NR_DRAM_BANKS           1
 245 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 246
 247 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 248 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 249 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 250
 251 #define CONFIG_SYS_INIT_SP_OFFSET \
 252         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 253 #define CONFIG_SYS_INIT_SP_ADDR \
 254         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 255
 256 /* FLASH and environment organization */
 257 #define CONFIG_SYS_NO_FLASH
 258
 259 #define CONFIG_ENV_IS_IN_SPI_FLASH
 260 #define CONFIG_ENV_SIZE                 (8 * 1024)
 261 #define CONFIG_ENV_OFFSET               (768 * 1024)
 262 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 263 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 264 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 265 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 266 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 267
 268 #ifndef CONFIG_SYS_DCACHE_OFF
 269 #endif
 270
 271 #define CONFIG_SYS_FSL_USDHC_NUM        3
 272
 273 /* Framebuffer */
 274 #define CONFIG_VIDEO_IPUV3
 275 #define CONFIG_VIDEO_BMP_RLE8
 276 #define CONFIG_SPLASH_SCREEN
 277 #define CONFIG_SPLASH_SCREEN_ALIGN
 278 #define CONFIG_BMP_16BPP
 279 #define CONFIG_VIDEO_LOGO
 280 #define CONFIG_VIDEO_BMP_LOGO
 281 #define CONFIG_IPUV3_CLK                260000000
 282 #define CONFIG_IMX_HDMI
 283 #define CONFIG_IMX_VIDEO_SKIP
 284
 285 #define CONFIG_PWM_IMX
 286 #define CONFIG_IMX6_PWM_PER_CLK         66000000
 287
 288 #undef CONFIG_CMD_PCI
 289 #ifdef CONFIG_CMD_PCI
 290 #define CONFIG_PCI
 291 #define CONFIG_PCI_PNP
 292 #define CONFIG_PCI_SCAN_SHOW
 293 #define CONFIG_PCIE_IMX
 294 #define CONFIG_PCIE_IMX_PERST_GPIO      IMX_GPIO_NR(7, 12)
 295 #define CONFIG_PCIE_IMX_POWER_GPIO      IMX_GPIO_NR(1, 5)
 296 #endif
 297
 298 /* I2C Configs */
 299 #define CONFIG_SYS_I2C
 300 #define CONFIG_SYS_I2C_MXC
 301 #define CONFIG_SYS_I2C_SPEED            100000
 302 #define CONFIG_SYS_I2C_MXC_I2C1
 303 #define CONFIG_SYS_I2C_MXC_I2C2
 304 #define CONFIG_SYS_I2C_MXC_I2C3
 305
 306 #endif  /* __ADVANTECH_DMSBA16_CONFIG_H */