2 * Copyright 2007 Freescale Semiconductor, Inc.
4 * This program is free software; you can redistribute it and/or
5 * modify it under the terms of the GNU General Public License
6 * Version 2 as published by the Free Software Foundation.
10 * MPC8610HPCD board configuration file
17 /* High Level Configuration Options */
18 #define CONFIG_MPC86xx 1 /* MPC86xx */
19 #define CONFIG_MPC8610 1 /* MPC8610 specific */
20 #define CONFIG_MPC8610HPCD 1 /* MPC8610HPCD board specific */
21 #define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */
22 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
25 #define CFG_DIAG_ADDR 0xff800000
28 #define CFG_RESET_ADDRESS 0xfff00100
30 #define CONFIG_PCI 1 /* Enable PCI/PCIE*/
31 #define CONFIG_PCI1 1 /* PCI controler 1 */
32 #define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */
33 #define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */
34 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
36 #define CONFIG_ENV_OVERWRITE
38 #define CONFIG_SPD_EEPROM /* Use SPD for DDR */
39 #undef CONFIG_DDR_DLL /* possible DLL fix needed */
40 #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
41 #define CONFIG_DDR_ECC /* only for ECC DDR module */
42 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
43 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef
44 #define CONFIG_NUM_DDR_CONTROLLERS 1
45 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
47 #define CONFIG_ALTIVEC 1
50 * L2CR setup -- make sure this is right for your board!
54 #define L2_ENABLE (L2CR_L2E)
56 #ifndef CONFIG_SYS_CLK_FREQ
57 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
60 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
62 #undef CFG_DRAM_TEST /* memory test, takes time */
63 #define CFG_MEMTEST_START 0x00200000 /* memtest region */
64 #define CFG_MEMTEST_END 0x00400000
65 #define CFG_ALT_MEMTEST
68 * Base addresses -- Note these are effective addresses where the
69 * actual resources get mapped (not physical addresses)
71 #define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
72 #define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
73 #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
75 #define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
76 #define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
77 #define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
79 #define CFG_DIU_ADDR (CFG_CCSRBAR+0x2c000)
84 #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
85 #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
86 #define CONFIG_VERY_BIG_RAM
88 #define MPC86xx_DDR_SDRAM_CLK_CNTL
90 #if defined(CONFIG_SPD_EEPROM)
92 * Determine DDR configuration from I2C interface.
94 #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
97 * Manually set up DDR1 parameters
100 #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
103 #define CFG_DDR_CS0_BNDS 0x0000000F
104 #define CFG_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
105 #define CFG_DDR_EXT_REFRESH 0x00000000
106 #define CFG_DDR_TIMING_0 0x00260802
107 #define CFG_DDR_TIMING_1 0x3935d322
108 #define CFG_DDR_TIMING_2 0x14904cc8
109 #define CFG_DDR_MODE_1 0x00480432
110 #define CFG_DDR_MODE_2 0x00000000
111 #define CFG_DDR_INTERVAL 0x06180100
112 #define CFG_DDR_DATA_INIT 0xdeadbeef
113 #define CFG_DDR_CLK_CTRL 0x03800000
114 #define CFG_DDR_OCD_CTRL 0x00000000
115 #define CFG_DDR_OCD_STATUS 0x00000000
116 #define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
117 #define CFG_DDR_CONTROL2 0x04400010
119 #define CFG_DDR_ERR_INT_EN 0x00000000
120 #define CFG_DDR_ERR_DIS 0x00000000
121 #define CFG_DDR_SBE 0x000f0000
122 /* Not used in fixed_sdram function */
123 #define CFG_DDR_MODE 0x00000022
124 #define CFG_DDR_CS1_BNDS 0x00000000
125 #define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
126 #define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
127 #define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
128 #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
132 #define CFG_ID_EEPROM
133 #define ID_EEPROM_ADDR 0x57
136 #define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */
137 #define CFG_FLASH_BASE2 0xf8000000
139 #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
141 #define CFG_BR0_PRELIM 0xf8001001 /* port size 16bit */
142 #define CFG_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/
144 #define CFG_BR1_PRELIM 0xf0001001 /* port size 16bit */
145 #define CFG_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */
147 #define CFG_BR2_PRELIM 0xf0000000
148 #define CFG_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */
150 #define CFG_BR3_PRELIM 0xe8000801 /* port size 8bit */
151 #define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
154 #define PIXIS_BASE 0xe8000000 /* PIXIS registers */
155 #define PIXIS_ID 0x0 /* Board ID at offset 0 */
156 #define PIXIS_VER 0x1 /* Board version at offset 1 */
157 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
158 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */
159 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */
160 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
161 #define PIXIS_VCTL 0x10 /* VELA Control Register */
162 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
163 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
164 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
165 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
166 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
167 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
168 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
170 #define CFG_MAX_FLASH_BANKS 2 /* number of banks */
171 #define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
173 #undef CFG_FLASH_CHECKSUM
174 #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
175 #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
176 #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
178 #define CFG_FLASH_CFI_DRIVER
179 #define CFG_FLASH_CFI
180 #define CFG_FLASH_EMPTY_INFO
182 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
188 #if defined(CFG_RAMBOOT)
189 #undef CONFIG_SPD_EEPROM
190 #define CFG_SDRAM_SIZE 256
193 #undef CONFIG_CLOCKS_IN_MHZ
195 #define CONFIG_L1_INIT_RAM
196 #define CFG_INIT_RAM_LOCK 1
197 #ifndef CFG_INIT_RAM_LOCK
198 #define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
200 #define CFG_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */
202 #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
204 #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
205 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
206 #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
208 #define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
209 #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
212 #define CONFIG_CONS_INDEX 1
213 #undef CONFIG_SERIAL_SOFTWARE_FIFO
215 #define CFG_NS16550_SERIAL
216 #define CFG_NS16550_REG_SIZE 1
217 #define CFG_NS16550_CLK get_bus_freq(0)
219 #define CFG_BAUDRATE_TABLE \
220 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
222 #define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
223 #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
225 /* Use the HUSH parser */
226 #define CFG_HUSH_PARSER
227 #ifdef CFG_HUSH_PARSER
228 #define CFG_PROMPT_HUSH_PS2 "> "
232 * Pass open firmware flat tree to kernel
234 #define CONFIG_OF_FLAT_TREE 1
235 #define CONFIG_OF_BOARD_SETUP 1
237 /* maximum size of the flat tree (8K) */
238 #define OF_FLAT_TREE_MAX_SIZE 8192
240 #define OF_CPU "PowerPC,8610@0"
241 #define OF_SOC "soc@e0000000"
242 #define OF_TBCLK (bd->bi_busfreq / 4)
243 #define OF_STDOUT_PATH "/soc@e0000000/serial@4500"
245 #define CFG_64BIT_VSPRINTF 1
246 #define CFG_64BIT_STRTOUL 1
251 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */
252 #define CONFIG_HARD_I2C /* I2C with hardware support*/
253 #undef CONFIG_SOFT_I2C /* I2C bit-banged */
254 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
255 #define CFG_I2C_SLAVE 0x7F
256 #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
257 #define CFG_I2C_OFFSET 0x3000
261 * Addresses are mapped 1-1.
263 #define CFG_PCI1_MEM_BASE 0x80000000
264 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
265 #define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
266 #define CFG_PCI1_IO_BASE 0x00000000
267 #define CFG_PCI1_IO_PHYS 0xe1000000
268 #define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
270 /* PCI view of System Memory */
271 #define CFG_PCI_MEMORY_BUS 0x00000000
272 #define CFG_PCI_MEMORY_PHYS 0x00000000
273 #define CFG_PCI_MEMORY_SIZE 0x80000000
276 #define KSEG1ADDR(x) ({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); })
277 #define _IO_BASE 0x00000000
279 /* controller 1, Base address 0xa000 */
280 #define CFG_PCIE1_MEM_BASE 0xa0000000
281 #define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
282 #define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */
283 #define CFG_PCIE1_IO_BASE 0x00000000
284 #define CFG_PCIE1_IO_PHYS 0xe3000000
285 #define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
287 /* controller 2, Base Address 0x9000 */
288 #define CFG_PCIE2_MEM_BASE 0x90000000
289 #define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
290 #define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */
291 #define CFG_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */
292 #define CFG_PCIE2_IO_PHYS 0xe2000000
293 #define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */
296 #if defined(CONFIG_PCI)
298 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
300 #define CONFIG_NET_MULTI
301 #define CONFIG_PCI_PNP /* do pci plug-and-play */
304 /* enable onboard uli network support */
307 #define CONFIG_RTL8139
309 #define CONFIG_EEPRO100
313 /************************************************************
315 ************************************************************/
316 #define CONFIG_USB_OHCI 1
317 #define CONFIG_USB_KEYBOARD 1
318 #define CFG_DEVICE_DEREGISTER
319 #define CFG_USB_INTERRUPT_POLL 1
322 #if !defined(CONFIG_PCI_PNP)
323 #define PCI_ENET0_IOADDR 0xe0000000
324 #define PCI_ENET0_MEMADDR 0xe0000000
325 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
328 #define CONFIG_DOS_PARTITION
329 #define CONFIG_SCSI_AHCI
331 #ifdef CONFIG_SCSI_AHCI
332 #define CONFIG_SATA_ULI5288
333 #define CFG_SCSI_MAX_SCSI_ID 4
334 #define CFG_SCSI_MAX_LUN 1
335 #define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
336 #define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
339 #endif /* CONFIG_PCI */
342 * BAT0 2G Cacheable, non-guarded
345 #define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
346 #define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
347 #define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
348 #define CFG_IBAT0U CFG_DBAT0U
351 * BAT1 1G Cache-inhibited, guarded
352 * 0x8000_0000 256M PCI-1 Memory
353 * 0xa000_0000 256M PCI-Express 1 Memory
354 * 0x9000_0000 256M PCI-Express 2 Memory
357 #define CFG_DBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
358 | BATL_GUARDEDSTORAGE)
359 #define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
360 #define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
361 #define CFG_IBAT1U CFG_DBAT1U
364 * BAT2 32M Cache-inhibited, guarded
365 * 0xe100_0000 1M PCI-1 I/O
366 * 0xe200_0000 1M PCI-Express 2 I/O
370 #define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
371 | BATL_GUARDEDSTORAGE)
372 #define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
373 #define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
374 #define CFG_IBAT2U CFG_DBAT2U
377 * BAT3 1M Cache-inhibited, guarded
378 * 0xe300_0000 1M PCI-Express 1 I/O
382 #define CFG_DBAT3L (CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
383 | BATL_GUARDEDSTORAGE)
384 #define CFG_DBAT3U (CFG_PCIE1_IO_PHYS | BATU_BL_1M | BATU_VS | BATU_VP)
385 #define CFG_IBAT3L (CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
386 #define CFG_IBAT3U CFG_DBAT3U
389 * BAT4 4M Cache-inhibited, guarded
390 * 0xe000_0000 4M CCSR
392 #define CFG_DBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
393 | BATL_GUARDEDSTORAGE)
394 #define CFG_DBAT4U (CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
395 #define CFG_IBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
396 #define CFG_IBAT4U CFG_DBAT4U
399 * BAT5 128K Cacheable, non-guarded
400 * 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
402 #define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
403 #define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
404 #define CFG_IBAT5L CFG_DBAT5L
405 #define CFG_IBAT5U CFG_DBAT5U
408 * BAT6 256M Cache-inhibited, guarded
409 * 0xf000_0000 256M FLASH
411 #define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
412 | BATL_GUARDEDSTORAGE)
413 #define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
414 #define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
415 #define CFG_IBAT6U CFG_DBAT6U
418 * BAT7 4M Cache-inhibited, guarded
419 * 0xe800_0000 4M PIXIS
421 #define CFG_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
422 | BATL_GUARDEDSTORAGE)
423 #define CFG_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
424 #define CFG_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
425 #define CFG_IBAT7U CFG_DBAT7U
432 #define CFG_ENV_IS_IN_FLASH 1
433 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
434 #define CFG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */
435 #define CFG_ENV_SIZE 0x2000
437 #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
438 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
439 #define CFG_ENV_SIZE 0x2000
442 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
443 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
449 #define CONFIG_BOOTP_BOOTFILESIZE
450 #define CONFIG_BOOTP_BOOTPATH
451 #define CONFIG_BOOTP_GATEWAY
452 #define CONFIG_BOOTP_HOSTNAME
456 * Command line configuration.
458 #include <config_cmd_default.h>
460 #define CONFIG_CMD_PING
461 #define CONFIG_CMD_I2C
462 #define CONFIG_CMD_MII
464 #if defined(CFG_RAMBOOT)
465 #undef CONFIG_CMD_ENV
468 #if defined(CONFIG_PCI)
469 #define CONFIG_CMD_PCI
470 #define CONFIG_CMD_SCSI
471 #define CONFIG_CMD_EXT2
475 #undef CONFIG_WATCHDOG /* watchdog disabled */
478 * Miscellaneous configurable options
480 #define CFG_LONGHELP /* undef to save memory */
481 #define CFG_LOAD_ADDR 0x2000000 /* default load address */
482 #define CFG_PROMPT "=> " /* Monitor Command Prompt */
484 #if defined(CONFIG_CMD_KGDB)
485 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
487 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
490 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
491 #define CFG_MAXARGS 16 /* max number of command args */
492 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
493 #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
496 * For booting Linux, the board info and command line data
497 * have to be in the first 8 MB of memory, since this is
498 * the maximum mapped by the Linux kernel during initialization.
500 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
502 /* Cache Configuration */
503 #define CFG_DCACHE_SIZE 32768
504 #define CFG_CACHELINE_SIZE 32
505 #if defined(CONFIG_CMD_KGDB)
506 #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
510 * Internal Definitions
514 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
515 #define BOOTFLAG_WARM 0x02 /* Software reboot */
517 #if defined(CONFIG_CMD_KGDB)
518 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
519 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
523 * Environment Configuration
525 #define CONFIG_IPADDR 192.168.1.100
527 #define CONFIG_HOSTNAME unknown
528 #define CONFIG_ROOTPATH /opt/nfsroot
529 #define CONFIG_BOOTFILE uImage
530 #define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin
532 #define CONFIG_SERVERIP 192.168.1.1
533 #define CONFIG_GATEWAYIP 192.168.1.1
534 #define CONFIG_NETMASK 255.255.255.0
536 /* default location for tftp and bootm */
537 #define CONFIG_LOADADDR 1000000
539 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
540 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
542 #define CONFIG_BAUDRATE 115200
544 #if defined(CONFIG_PCI1)
546 "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
547 "echo e;md ${a}e00 9\0" \
548 "pci1regs=setenv a e0008; run pcireg\0" \
549 "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
550 "pci d.w $b.0 56 1\0" \
551 "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
552 "pci w.w $b.0 56 ffff\0" \
553 "pci1err=setenv a e0008; run pcierr\0" \
554 "pci1errc=setenv a e0008; run pcierrc\0"
559 #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
561 "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
562 "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
563 "pcie1regs=setenv a e000a; run pciereg\0" \
564 "pcie2regs=setenv a e0009; run pciereg\0" \
565 "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
566 "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \
567 "pci d $b.0 130 1\0" \
568 "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
569 "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
570 "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \
571 "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
572 "pcie1err=setenv a e000a; run pcieerr\0" \
573 "pcie2err=setenv a e0009; run pcieerr\0" \
574 "pcie1errc=setenv a e000a; run pcieerrc\0" \
575 "pcie2errc=setenv a e0009; run pcieerrc\0"
581 "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
582 "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
583 "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
584 "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
585 "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
586 "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
587 "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
588 "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
591 #define CONFIG_EXTRA_ENV_SETTINGS \
593 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
594 "tftpflash=tftpboot $loadaddr $uboot; " \
595 "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
596 "erase " MK_STR(TEXT_BASE) " +$filesize; " \
597 "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
598 "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
599 "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
600 "consoledev=ttyS0\0" \
601 "ramdiskaddr=2000000\0" \
602 "ramdiskfile=8610hpcd/ramdisk.uboot\0" \
604 "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0" \
606 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
607 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
609 "eoi=mw e00400b0 0\0" \
610 "iack=md e00400a0 1\0" \
611 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
612 "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
614 "ddr1regs=setenv a e0002; run ddrreg\0" \
615 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
616 "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
617 "md ${a}e60 1; md ${a}ef0 1d\0" \
618 "guregs=setenv a e00e0; run gureg\0" \
619 "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
620 "mcmregs=setenv a e0001; run mcmreg\0" \
621 "diuregs=md e002c000 1d\0" \
622 "dium=mw e002c01c\0" \
623 "diuerr=md e002c014 1\0" \
624 "othbootargs=debug\0" \
625 "pmregs=md e00e1000 2b\0" \
626 "lawregs=md e0000c08 4b\0" \
627 "lbcregs=md e0005000 36\0" \
628 "dma0regs=md e0021100 12\0" \
629 "dma1regs=md e0021180 12\0" \
630 "dma2regs=md e0021200 12\0" \
631 "dma3regs=md e0021280 12\0" \
636 #define CONFIG_NFSBOOTCOMMAND \
637 "setenv bootargs root=/dev/nfs rw " \
638 "nfsroot=$serverip:$rootpath " \
639 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
640 "console=$consoledev,$baudrate $othbootargs;" \
641 "tftp $loadaddr $bootfile;" \
642 "tftp $dtbaddr $dtbfile;" \
643 "bootm $loadaddr - $dtbaddr"
645 #define CONFIG_RAMBOOTCOMMAND \
646 "setenv bootargs root=/dev/ram rw " \
647 "console=$consoledev,$baudrate $othbootargs;" \
648 "tftp $ramdiskaddr $ramdiskfile;" \
649 "tftp $loadaddr $bootfile;" \
650 "tftp $dtbaddr $dtbfile;" \
651 "bootm $loadaddr $ramdiskaddr $dtbaddr"
653 #define CONFIG_BOOTCOMMAND \
654 "setenv bootargs root=/dev/$bdev rw " \
655 "console=$consoledev,$baudrate $othbootargs;" \
656 "tftp $loadaddr $bootfile;" \
657 "tftp $dtbaddr $dtbfile;" \
658 "bootm $loadaddr - $dtbaddr"
660 #endif /* __CONFIG_H */