1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010.
6 * mpc8313epb board configuration file
13 * High Level Configuration Options
17 #ifndef CONFIG_SYS_MONITOR_BASE
18 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
21 #define CONFIG_PCI_INDIRECT_BRIDGE
22 #define CONFIG_FSL_ELBC 1
30 #define CONFIG_VSC7385_ENET
33 #define CONFIG_SYS_MEMTEST_START 0x00001000
34 #define CONFIG_SYS_MEMTEST_END 0x07f00000
36 /* Early revs of this board will lock up hard when attempting
37 * to access the PMC registers, unless a JTAG debugger is
38 * connected, or some resistor modifications are made.
40 #define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
43 * Device configurations
48 #ifdef CONFIG_VSC7385_ENET
52 /* The flash address and size of the VSC7385 firmware image */
53 #define CONFIG_VSC7385_IMAGE 0xFE7FE000
54 #define CONFIG_VSC7385_IMAGE_SIZE 8192
61 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
62 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
63 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
66 * Manually set up DDR parameters, as this board does not
67 * seem to have the SPD connected to I2C.
69 #define CONFIG_SYS_DDR_SIZE 128 /* MB */
70 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
71 | CSCONFIG_ODT_RD_NEVER \
72 | CSCONFIG_ODT_WR_ONLY_CURRENT \
73 | CSCONFIG_ROW_BIT_13 \
74 | CSCONFIG_COL_BIT_10)
77 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
78 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
79 | (0 << TIMING_CFG0_WRT_SHIFT) \
80 | (0 << TIMING_CFG0_RRT_SHIFT) \
81 | (0 << TIMING_CFG0_WWT_SHIFT) \
82 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
83 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
84 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
85 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
87 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
88 | (8 << TIMING_CFG1_ACTTOPRE_SHIFT) \
89 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
90 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
91 | (10 << TIMING_CFG1_REFREC_SHIFT) \
92 | (3 << TIMING_CFG1_WRREC_SHIFT) \
93 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
94 | (2 << TIMING_CFG1_WRTORD_SHIFT))
96 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
97 | (5 << TIMING_CFG2_CPO_SHIFT) \
98 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
99 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
100 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
101 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
102 | (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
103 /* 0x129048c6 */ /* P9-45,may need tuning */
104 #define CONFIG_SYS_DDR_INTERVAL ((1296 << SDRAM_INTERVAL_REFINT_SHIFT) \
105 | (1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
107 #if defined(CONFIG_DDR_2T_TIMING)
108 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \
109 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
114 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \
115 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
119 #define CONFIG_SYS_SDRAM_CFG2 0x00401000
120 /* set burst length to 8 for 32-bit data path */
121 #define CONFIG_SYS_DDR_MODE ((0x4448 << SDRAM_MODE_ESD_SHIFT) \
122 | (0x0632 << SDRAM_MODE_SD_SHIFT))
124 #define CONFIG_SYS_DDR_MODE_2 0x8000C000
126 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
128 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
134 * FLASH on the Local Bus
136 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
137 #define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */
138 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
139 #define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
141 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
142 #define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */
144 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
145 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
147 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && \
148 !defined(CONFIG_SPL_BUILD)
149 #define CONFIG_SYS_RAMBOOT
152 #define CONFIG_SYS_INIT_RAM_LOCK 1
153 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
154 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
156 #define CONFIG_SYS_GBL_DATA_OFFSET \
157 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
158 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
160 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
161 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
162 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
165 * Local Bus LCRR and LBCR regs
167 #define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
168 | (0xFF << LBCR_BMT_SHIFT) \
169 | 0xF) /* 0x0004ff0f */
171 /* LB refresh timer prescal, 266MHz/32 */
172 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /*TODO */
174 /* drivers/mtd/nand/nand.c */
175 #define CONFIG_SYS_NAND_BASE 0xE2800000
177 #define CONFIG_MTD_PARTITION
179 #define CONFIG_SYS_MAX_NAND_DEVICE 1
180 #define CONFIG_NAND_FSL_ELBC 1
181 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384
182 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
184 /* Still needed for spl_minimal.c */
185 #define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
186 #define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
188 /* local bus write LED / read status buffer (BCSR) mapping */
189 #define CONFIG_SYS_BCSR_ADDR 0xFA000000
190 #define CONFIG_SYS_BCSR_SIZE (32 * 1024) /* 0x00008000 */
191 /* map at 0xFA000000 on LCS3 */
194 #ifdef CONFIG_VSC7385_ENET
196 /* VSC7385 Base address on LCS2 */
197 #define CONFIG_SYS_VSC7385_BASE 0xF0000000
198 #define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */
203 #define CONFIG_MPC83XX_GPIO 1
208 #define CONFIG_SYS_NS16550_SERIAL
209 #define CONFIG_SYS_NS16550_REG_SIZE 1
211 #define CONFIG_SYS_BAUDRATE_TABLE \
212 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
214 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
215 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
218 #define CONFIG_SYS_I2C
219 #define CONFIG_SYS_I2C_FSL
220 #define CONFIG_SYS_FSL_I2C_SPEED 400000
221 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
222 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
223 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
224 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
225 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
226 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
230 * Addresses are mapped 1-1.
232 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
233 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
234 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
235 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
236 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
237 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
238 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000
239 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
240 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
242 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
248 #define CONFIG_GMII /* MII PHY management */
251 #define CONFIG_HAS_ETH0
252 #define CONFIG_TSEC1_NAME "TSEC0"
253 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
254 #define TSEC1_PHY_ADDR 0x1c
255 #define TSEC1_FLAGS TSEC_GIGABIT
256 #define TSEC1_PHYIDX 0
260 #define CONFIG_HAS_ETH1
261 #define CONFIG_TSEC2_NAME "TSEC1"
262 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
263 #define TSEC2_PHY_ADDR 4
264 #define TSEC2_FLAGS TSEC_GIGABIT
265 #define TSEC2_PHYIDX 0
268 /* Options are: TSEC[0-1] */
269 #define CONFIG_ETHPRIME "TSEC1"
272 * Configure on-board RTC
274 #define CONFIG_RTC_DS1337
275 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
280 #if !defined(CONFIG_SYS_RAMBOOT)
281 #define CONFIG_ENV_ADDR \
282 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
283 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
284 #define CONFIG_ENV_SIZE 0x2000
286 /* Address and size of Redundant Environment Sector */
288 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
289 #define CONFIG_ENV_SIZE 0x2000
292 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
293 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
298 #define CONFIG_BOOTP_BOOTFILESIZE
301 * Command line configuration.
305 * Miscellaneous configurable options
307 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
308 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
310 /* Boot Argument Buffer Size */
311 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
314 * For booting Linux, the board info and command line data
315 * have to be in the first 256 MB of memory, since this is
316 * the maximum mapped by the Linux kernel during initialization.
318 /* Initial Memory map for Linux*/
319 #define CONFIG_SYS_BOOTMAPSZ (256 << 20)
320 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
322 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
324 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
326 /* System IO Config */
327 #define CONFIG_SYS_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */
328 /* Enable Internal USB Phy and GPIO on LCD Connector */
329 #define CONFIG_SYS_SICRL (SICRL_USBDR_10 | SICRL_LBC)
332 * Environment Configuration
334 #define CONFIG_ENV_OVERWRITE
336 #define CONFIG_NETDEV "eth1"
338 #define CONFIG_HOSTNAME "mpc8313erdb"
339 #define CONFIG_ROOTPATH "/nfs/root/path"
340 #define CONFIG_BOOTFILE "uImage"
341 /* U-Boot image on TFTP server */
342 #define CONFIG_UBOOTPATH "u-boot.bin"
343 #define CONFIG_FDTFILE "mpc8313erdb.dtb"
345 /* default location for tftp and bootm */
346 #define CONFIG_LOADADDR 800000
348 #define CONFIG_EXTRA_ENV_SETTINGS \
349 "netdev=" CONFIG_NETDEV "\0" \
351 "uboot=" CONFIG_UBOOTPATH "\0" \
352 "tftpflash=tftpboot $loadaddr $uboot; " \
353 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
355 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
357 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
359 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
361 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
364 "fdtfile=" CONFIG_FDTFILE "\0" \
366 "setbootargs=setenv bootargs " \
367 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
368 "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
369 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\
371 "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
373 #define CONFIG_NFSBOOTCOMMAND \
374 "setenv rootdev /dev/nfs;" \
377 "tftp $loadaddr $bootfile;" \
378 "tftp $fdtaddr $fdtfile;" \
379 "bootm $loadaddr - $fdtaddr"
381 #define CONFIG_RAMBOOTCOMMAND \
382 "setenv rootdev /dev/ram;" \
384 "tftp $ramdiskaddr $ramdiskfile;" \
385 "tftp $loadaddr $bootfile;" \
386 "tftp $fdtaddr $fdtfile;" \
387 "bootm $loadaddr $ramdiskaddr $fdtaddr"
389 #endif /* __CONFIG_H */