ARMV7: AM3517/05: Add support for CraneBoard.
[oweals/u-boot.git] / include / configs / MPC8308RDB.h
1 /*
2  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
3  * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
4  *
5  *
6  * See file CREDITS for list of people who contributed to this
7  * project.
8  *
9  * This program is free software; you can redistribute it and/or
10  * modify it under the terms of the GNU General Public License as
11  * published by the Free Software Foundation; either version 2 of
12  * the License, or (at your option) any later version.
13  *
14  * This program is distributed in the hope that it will be useful,
15  * but WITHOUT ANY WARRANTY; without even the implied warranty of
16  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17  * GNU General Public License for more details.
18  *
19  * You should have received a copy of the GNU General Public License
20  * along with this program; if not, write to the Free Software
21  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
22  * MA 02111-1307 USA
23  */
24
25 #ifndef __CONFIG_H
26 #define __CONFIG_H
27
28 /*
29  * High Level Configuration Options
30  */
31 #define CONFIG_E300             1 /* E300 family */
32 #define CONFIG_MPC83xx          1 /* MPC83xx family */
33 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
34 #define CONFIG_MPC8308RDB       1 /* MPC8308RDB board specific */
35
36 #define CONFIG_SYS_TEXT_BASE    0xFE000000
37
38 #define CONFIG_MISC_INIT_R
39
40 /*
41  * On-board devices
42  *
43  * TSEC1 is SoC TSEC
44  * TSEC2 is VSC switch
45  */
46 #define CONFIG_TSEC1
47 #define CONFIG_VSC7385_ENET
48
49 /*
50  * System Clock Setup
51  */
52 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
53 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
54
55 /*
56  * Hardware Reset Configuration Word
57  * if CLKIN is 66.66MHz, then
58  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
59  * We choose the A type silicon as default, so the core is 400Mhz.
60  */
61 #define CONFIG_SYS_HRCW_LOW (\
62         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
63         HRCWL_DDR_TO_SCB_CLK_2X1 |\
64         HRCWL_SVCOD_DIV_2 |\
65         HRCWL_CSB_TO_CLKIN_4X1 |\
66         HRCWL_CORE_TO_CSB_3X1)
67 /*
68  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
69  * in 8308's HRCWH according to the manual, but original Freescale's
70  * code has them and I've expirienced some problems using the board
71  * with BDI3000 attached when I've tried to set these bits to zero
72  * (UART doesn't work after the 'reset run' command).
73  */
74 #define CONFIG_SYS_HRCW_HIGH (\
75         HRCWH_PCI_HOST |\
76         HRCWH_PCI1_ARBITER_ENABLE |\
77         HRCWH_CORE_ENABLE |\
78         HRCWH_FROM_0X00000100 |\
79         HRCWH_BOOTSEQ_DISABLE |\
80         HRCWH_SW_WATCHDOG_DISABLE |\
81         HRCWH_ROM_LOC_LOCAL_16BIT |\
82         HRCWH_RL_EXT_LEGACY |\
83         HRCWH_TSEC1M_IN_RGMII |\
84         HRCWH_TSEC2M_IN_RGMII |\
85         HRCWH_BIG_ENDIAN)
86
87 /*
88  * System IO Config
89  */
90 #define CONFIG_SYS_SICRH (\
91         SICRH_ESDHC_A_SD |\
92         SICRH_ESDHC_B_SD |\
93         SICRH_ESDHC_C_SD |\
94         SICRH_GPIO_A_TSEC2 |\
95         SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
96         SICRH_IEEE1588_A_GPIO |\
97         SICRH_USB |\
98         SICRH_GTM_GPIO |\
99         SICRH_IEEE1588_B_GPIO |\
100         SICRH_ETSEC2_CRS |\
101         SICRH_GPIOSEL_1 |\
102         SICRH_TMROBI_V3P3 |\
103         SICRH_TSOBI1_V2P5 |\
104         SICRH_TSOBI2_V2P5)      /* 0x01b7d103 */
105 #define CONFIG_SYS_SICRL (\
106         SICRL_SPI_PF0 |\
107         SICRL_UART_PF0 |\
108         SICRL_IRQ_PF0 |\
109         SICRL_I2C2_PF0 |\
110         SICRL_ETSEC1_GTX_CLK125)        /* 0x00000040 */
111
112 /*
113  * IMMR new address
114  */
115 #define CONFIG_SYS_IMMR         0xE0000000
116
117 /*
118  * SERDES
119  */
120 #define CONFIG_FSL_SERDES
121 #define CONFIG_FSL_SERDES1      0xe3000
122
123 /*
124  * Arbiter Setup
125  */
126 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
127 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
128 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
129
130 /*
131  * DDR Setup
132  */
133 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
134 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
135 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
136 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
137 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
138                                 | DDRCDR_PZ_LOZ \
139                                 | DDRCDR_NZ_LOZ \
140                                 | DDRCDR_ODT \
141                                 | DDRCDR_Q_DRN)
142                                 /* 0x7b880001 */
143 /*
144  * Manually set up DDR parameters
145  * consist of two chips HY5PS12621BFP-C4 from HYNIX
146  */
147
148 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
149
150 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
151 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
152                                 | 0x00010000  /* ODT_WR to CSn */ \
153                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
154                                 /* 0x80010102 */
155 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
156 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
157                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
158                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
159                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
160                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
161                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
162                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
163                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
164                                 /* 0x00220802 */
165 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
166                                 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
167                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
168                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
169                                 | (6 << TIMING_CFG1_REFREC_SHIFT) \
170                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
171                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
172                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
173                                 /* 0x27256222 */
174 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
175                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
176                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
177                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
178                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
179                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
180                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
181                                 /* 0x121048c5 */
182 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
183                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
184                                 /* 0x03600100 */
185 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
186                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
187                                 | SDRAM_CFG_32_BE)
188                                 /* 0x43080000 */
189
190 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
191 #define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
192                                 | (0x0232 << SDRAM_MODE_SD_SHIFT))
193                                 /* ODT 150ohm CL=3, AL=1 on SDRAM */
194 #define CONFIG_SYS_DDR_MODE2            0x00000000
195
196 /*
197  * Memory test
198  */
199 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
200 #define CONFIG_SYS_MEMTEST_END          0x07f00000
201
202 /*
203  * The reserved memory
204  */
205 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
206
207 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
208 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
209
210 /*
211  * Initial RAM Base Address Setup
212  */
213 #define CONFIG_SYS_INIT_RAM_LOCK        1
214 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
215 #define CONFIG_SYS_INIT_RAM_SIZE                0x1000 /* Size of used area in RAM */
216 #define CONFIG_SYS_GBL_DATA_OFFSET      \
217         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
218
219 /*
220  * Local Bus Configuration & Clock Setup
221  */
222 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
223 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
224 #define CONFIG_SYS_LBC_LBCR             0x00040000
225
226 /*
227  * FLASH on the Local Bus
228  */
229 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
230 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
231 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
232
233 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
234 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is 8M */
235 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
236
237 /* Window base at flash base */
238 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
239 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
240
241 #define CONFIG_SYS_BR0_PRELIM   (\
242                 CONFIG_SYS_FLASH_BASE   /* Flash Base address */        |\
243                 (2 << BR_PS_SHIFT)      /* 16 bit port size */          |\
244                 BR_V)                   /* valid */
245 #define CONFIG_SYS_OR0_PRELIM   ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
246                                 | OR_UPM_XAM \
247                                 | OR_GPCM_CSNT \
248                                 | OR_GPCM_ACS_DIV2 \
249                                 | OR_GPCM_XACS \
250                                 | OR_GPCM_SCY_15 \
251                                 | OR_GPCM_TRLX \
252                                 | OR_GPCM_EHTR \
253                                 | OR_GPCM_EAD)
254
255 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
256 /* 127 64KB sectors and 8 8KB top sectors per device */
257 #define CONFIG_SYS_MAX_FLASH_SECT       135
258
259 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
260 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
261
262 /*
263  * NAND Flash on the Local Bus
264  */
265 #define CONFIG_SYS_NAND_BASE            0xE0600000      /* 0xE0600000 */
266 #define CONFIG_SYS_BR1_PRELIM   ( CONFIG_SYS_NAND_BASE \
267                                 | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
268                                 | BR_PS_8               /* Port Size = 8 bit */ \
269                                 | BR_MS_FCM             /* MSEL = FCM */ \
270                                 | BR_V )                /* valid */
271 #define CONFIG_SYS_OR1_PRELIM   ( 0xFFFF8000            /* length 32K */ \
272                                 | OR_FCM_CSCT \
273                                 | OR_FCM_CST \
274                                 | OR_FCM_CHT \
275                                 | OR_FCM_SCY_1 \
276                                 | OR_FCM_TRLX \
277                                 | OR_FCM_EHTR )
278                                 /* 0xFFFF8396 */
279
280 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
281 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)
282
283 #ifdef CONFIG_VSC7385_ENET
284 #define CONFIG_TSEC2
285 #define CONFIG_SYS_VSC7385_BASE         0xF0000000
286 #define CONFIG_SYS_BR2_PRELIM           0xf0000801 /* VSC7385 Base address */
287 #define CONFIG_SYS_OR2_PRELIM           0xfffe09ff /* VSC7385, 128K bytes*/
288 /* Access window base at VSC7385 base */
289 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_VSC7385_BASE
290 /* Access window size 128K */
291 #define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_128KB)
292 /* The flash address and size of the VSC7385 firmware image */
293 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
294 #define CONFIG_VSC7385_IMAGE_SIZE       8192
295 #endif
296 /*
297  * Serial Port
298  */
299 #define CONFIG_CONS_INDEX       1
300 #define CONFIG_SYS_NS16550
301 #define CONFIG_SYS_NS16550_SERIAL
302 #define CONFIG_SYS_NS16550_REG_SIZE     1
303 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
304
305 #define CONFIG_SYS_BAUDRATE_TABLE  \
306         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
307
308 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
309 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
310
311 /* Use the HUSH parser */
312 #define CONFIG_SYS_HUSH_PARSER
313 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
314
315 /* Pass open firmware flat tree */
316 #define CONFIG_OF_LIBFDT        1
317 #define CONFIG_OF_BOARD_SETUP   1
318 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
319
320 /* I2C */
321 #define CONFIG_HARD_I2C         /* I2C with hardware support */
322 #define CONFIG_FSL_I2C
323 #define CONFIG_I2C_MULTI_BUS
324 #define CONFIG_SYS_I2C_SPEED    400000 /* I2C speed and slave address */
325 #define CONFIG_SYS_I2C_SLAVE    0x7F
326 #define CONFIG_SYS_I2C_NOPROBES {{0x51}} /* Don't probe these addrs */
327 #define CONFIG_SYS_I2C_OFFSET   0x3000
328 #define CONFIG_SYS_I2C2_OFFSET  0x3100
329
330
331 /*
332  * Board info - revision and where boot from
333  */
334 #define CONFIG_SYS_I2C_PCF8574A_ADDR    0x39
335
336 /*
337  * Config on-board RTC
338  */
339 #define CONFIG_RTC_DS1337       /* ds1339 on board, use ds1337 rtc via i2c */
340 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
341
342 /*
343  * General PCI
344  * Addresses are mapped 1-1.
345  */
346 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
347 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
348 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
349 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
350 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
351 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
352 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
353 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
354 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
355
356 /* enable PCIE clock */
357 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
358
359 #define CONFIG_PCI
360 #define CONFIG_PCIE
361
362 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
363
364 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
365 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
366
367 /*
368  * TSEC
369  */
370 #define CONFIG_NET_MULTI
371 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
372 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
373 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
374 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
375 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
376
377 /*
378  * TSEC ethernet configuration
379  */
380 #define CONFIG_MII              1 /* MII PHY management */
381 #define CONFIG_TSEC1_NAME       "eTSEC0"
382 #define CONFIG_TSEC2_NAME       "eTSEC1"
383 #define TSEC1_PHY_ADDR          2
384 #define TSEC2_PHY_ADDR          1
385 #define TSEC1_PHYIDX            0
386 #define TSEC2_PHYIDX            0
387 #define TSEC1_FLAGS             TSEC_GIGABIT
388 #define TSEC2_FLAGS             TSEC_GIGABIT
389
390 /* Options are: eTSEC[0-1] */
391 #define CONFIG_ETHPRIME         "eTSEC0"
392
393 /*
394  * Environment
395  */
396 #define CONFIG_ENV_IS_IN_FLASH  1
397 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
398                                  CONFIG_SYS_MONITOR_LEN)
399 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
400 #define CONFIG_ENV_SIZE         0x2000
401 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
402 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
403
404 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
405 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
406
407 /*
408  * BOOTP options
409  */
410 #define CONFIG_BOOTP_BOOTFILESIZE
411 #define CONFIG_BOOTP_BOOTPATH
412 #define CONFIG_BOOTP_GATEWAY
413 #define CONFIG_BOOTP_HOSTNAME
414
415 /*
416  * Command line configuration.
417  */
418 #include <config_cmd_default.h>
419
420 #define CONFIG_CMD_DATE
421 #define CONFIG_CMD_DHCP
422 #define CONFIG_CMD_I2C
423 #define CONFIG_CMD_MII
424 #define CONFIG_CMD_NET
425 #define CONFIG_CMD_PCI
426 #define CONFIG_CMD_PING
427
428 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
429
430 /*
431  * Miscellaneous configurable options
432  */
433 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
434 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
435 #define CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt */
436
437 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
438
439 /* Print Buffer Size */
440 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
441 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
442 /* Boot Argument Buffer Size */
443 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
444 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */
445
446 /*
447  * For booting Linux, the board info and command line data
448  * have to be in the first 256 MB of memory, since this is
449  * the maximum mapped by the Linux kernel during initialization.
450  */
451 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
452
453 /*
454  * Core HID Setup
455  */
456 #define CONFIG_SYS_HID0_INIT    0x000000000
457 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
458                                  HID0_ENABLE_INSTRUCTION_CACHE | \
459                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
460 #define CONFIG_SYS_HID2         HID2_HBE
461
462 /*
463  * MMU Setup
464  */
465
466 /* DDR: cache cacheable */
467 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
468                                         BATL_MEMCOHERENCE)
469 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
470                                         BATU_VS | BATU_VP)
471 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
472 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
473
474 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
475 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_10 | \
476                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
477 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
478                                         BATU_VP)
479 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
480 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
481
482 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
483 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
484                                         BATL_MEMCOHERENCE)
485 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
486                                         BATU_VS | BATU_VP)
487 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
488                                         BATL_CACHEINHIBIT | \
489                                         BATL_GUARDEDSTORAGE)
490 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
491
492 /* Stack in dcache: cacheable, no memory coherence */
493 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
494 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
495                                         BATU_VS | BATU_VP)
496 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
497 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
498
499 /*
500  * Environment Configuration
501  */
502
503 #define CONFIG_ENV_OVERWRITE
504
505 #if defined(CONFIG_TSEC_ENET)
506 #define CONFIG_HAS_ETH0
507 #define CONFIG_HAS_ETH1
508 #endif
509
510 #define CONFIG_BAUDRATE 115200
511
512 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
513
514 #define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */
515
516 #define xstr(s) str(s)
517 #define str(s)  #s
518
519 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
520         "netdev=eth0\0"                                                 \
521         "consoledev=ttyS0\0"                                            \
522         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
523                 "nfsroot=${serverip}:${rootpath}\0"                     \
524         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
525         "addip=setenv bootargs ${bootargs} "                            \
526                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
527                 ":${hostname}:${netdev}:off panic=1\0"                  \
528         "addtty=setenv bootargs ${bootargs}"                            \
529                 " console=${consoledev},${baudrate}\0"                  \
530         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
531         "addmisc=setenv bootargs ${bootargs}\0"                         \
532         "kernel_addr=FE080000\0"                                        \
533         "fdt_addr=FE280000\0"                                           \
534         "ramdisk_addr=FE290000\0"                                       \
535         "u-boot=mpc8308rdb/u-boot.bin\0"                                \
536         "kernel_addr_r=1000000\0"                                       \
537         "fdt_addr_r=C00000\0"                                           \
538         "hostname=mpc8308rdb\0"                                         \
539         "bootfile=mpc8308rdb/uImage\0"                                  \
540         "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0"                           \
541         "rootpath=/opt/eldk-4.2/ppc_6xx\0"                              \
542         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
543                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
544         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
545                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
546         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
547                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
548                 "run nfsargs addip addtty addmtd addmisc;"              \
549                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
550         "bootcmd=run flash_self\0"                                      \
551         "load=tftp ${loadaddr} ${u-boot}\0"                             \
552         "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE)             \
553                 " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE)      \
554                 " +${filesize};cp.b ${fileaddr} "                       \
555                 xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"          \
556         "upd=run load update\0"                                         \
557
558 #endif  /* __CONFIG_H */