1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Configuation settings for the esd TASREG board.
6 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
10 * board/config.h - configuration options, board specific
17 * High Level Configuration Options
22 #define CONFIG_MCFUART
23 #define CONFIG_SYS_UART_PORT (0)
25 #undef CONFIG_WATCHDOG
27 #undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */
32 #undef CONFIG_BOOTP_BOOTFILESIZE
35 * Command line configuration.
38 #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
40 #define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */
42 #define CONFIG_SYS_MEMTEST_START 0x400
43 #define CONFIG_SYS_MEMTEST_END 0x380000
46 * Clock configuration: enable only one of the following options
49 #undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */
50 #define CONFIG_SYS_FAST_CLK 1 /* MCF5249 can run at 140MHz */
51 #define CONFIG_SYS_CLK 132025600 /* MCF5249 can run at 140MHz */
54 * Low Level Configuration Settings
55 * (address mappings, register initial values, etc.)
56 * You should know what you are doing if you make changes here.
59 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
60 #define CONFIG_SYS_MBAR2 0x80000000
62 /*-----------------------------------------------------------------------
63 * Definitions for initial stack pointer and data area (in DPRAM)
65 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
66 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
67 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
68 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
70 #define LDS_BOARD_TEXT \
71 . = DEFINED(env_offset) ? env_offset : .; \
72 env/embedded.o(.text);
74 #define CONFIG_ENV_OFFSET 0x4000 /* Address of Environment Sector*/
75 #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
76 #define CONFIG_ENV_SECT_SIZE 0x2000 /* see README - env sector total size */
78 /*-----------------------------------------------------------------------
79 * Start addresses for the final memory configuration
80 * (Set up by the startup code)
81 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
83 #define CONFIG_SYS_SDRAM_BASE 0x00000000
84 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
85 #define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
88 #define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
91 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
93 #define CONFIG_SYS_MONITOR_LEN 0x20000
94 #define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */
95 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
98 * For booting Linux, the board info and command line data
99 * have to be in the first 8 MB of memory, since this is
100 * the maximum mapped by the Linux kernel during initialization ??
102 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
104 /*-----------------------------------------------------------------------
107 #ifdef CONFIG_SYS_FLASH_CFI
109 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
110 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
111 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
112 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
113 # define CONFIG_SYS_FLASH_CHECKSUM
114 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
117 /*-----------------------------------------------------------------------
118 * Cache Configuration
120 #define CONFIG_SYS_CACHELINE_SIZE 16
122 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
123 CONFIG_SYS_INIT_RAM_SIZE - 8)
124 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
125 CONFIG_SYS_INIT_RAM_SIZE - 4)
126 #define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM)
127 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \
129 CF_ACR_EN | CF_ACR_SM_ALL)
130 #define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \
131 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
132 CF_ACR_EN | CF_ACR_SM_ALL)
133 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \
136 /*-----------------------------------------------------------------------
137 * Memory bank definitions
140 /* CS0 - AMD Flash, address 0xffc00000 */
141 #define CONFIG_SYS_CS0_BASE 0xffe00000
142 #define CONFIG_SYS_CS0_CTRL 0x00001980 /* WS=0110, AA=1, PS=10 */
143 /** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
144 #define CONFIG_SYS_CS0_MASK 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */
146 /* CS1 - FPGA, address 0xe0000000 */
147 #define CONFIG_SYS_CS1_BASE 0xe0000000
148 #define CONFIG_SYS_CS1_CTRL 0x00000d80 /* WS=0011, AA=1, PS=10 */
149 #define CONFIG_SYS_CS1_MASK 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/
151 /*-----------------------------------------------------------------------
154 #define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
155 #define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/
156 #define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */
157 #define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */
158 #define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */
159 #define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
160 #define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */