include/configs/BSC9131RDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2011-2012 Freescale Semiconductor, Inc.
   4  */
   5
   6 /*
   7  * BSC9131 RDB board configuration file
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_NAND_FSL_IFC
  14
  15 #ifdef CONFIG_SPIFLASH
  16 #define CONFIG_RAMBOOT_SPIFLASH
  17 #define CONFIG_SYS_RAMBOOT
  18 #define CONFIG_SYS_EXTRA_ENV_RELOC
  19 #define CONFIG_RESET_VECTOR_ADDRESS     0x110bfffc
  20 #endif
  21
  22 #ifdef CONFIG_NAND
  23 #define CONFIG_SPL_INIT_MINIMAL
  24 #define CONFIG_SPL_NAND_BOOT
  25 #define CONFIG_SPL_FLUSH_IMAGE
  26 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  27
  28 #define CONFIG_SPL_TEXT_BASE            0xFFFFE000
  29 #define CONFIG_SPL_MAX_SIZE             8192
  30 #define CONFIG_SPL_RELOC_TEXT_BASE      0x00100000
  31 #define CONFIG_SPL_RELOC_STACK          0x00100000
  32 #define CONFIG_SYS_NAND_U_BOOT_SIZE     ((768 << 10) - 0x2000)
  33 #define CONFIG_SYS_NAND_U_BOOT_DST      (0x00200000 - CONFIG_SPL_MAX_SIZE)
  34 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  35 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0
  36 #define CONFIG_SYS_LDSCRIPT     "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  37 #endif
  38
  39 #ifdef CONFIG_SPL_BUILD
  40 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
  41 #else
  42 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  43 #endif
  44
  45 /* High Level Configuration Options */
  46
  47 #define CONFIG_ENV_OVERWRITE
  48
  49 #define CONFIG_DDR_CLK_FREQ     66666666 /* DDRCLK on 9131 RDB */
  50 #if defined(CONFIG_SYS_CLK_100)
  51 #define CONFIG_SYS_CLK_FREQ    100000000 /* SYSCLK for 9131 RDB */
  52 #else
  53 #define CONFIG_SYS_CLK_FREQ     66666666 /* SYSCLK for 9131 RDB */
  54 #endif
  55
  56 #define CONFIG_HWCONFIG
  57 /*
  58  * These can be toggled for performance analysis, otherwise use default.
  59  */
  60 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  61 #define CONFIG_BTB                      /* enable branch predition */
  62
  63 #define CONFIG_SYS_MEMTEST_START        0x01000000      /* memtest works on */
  64 #define CONFIG_SYS_MEMTEST_END          0x01ffffff
  65
  66 /* DDR Setup */
  67 #undef CONFIG_SYS_DDR_RAW_TIMING
  68 #undef CONFIG_DDR_SPD
  69 #define CONFIG_SYS_SPD_BUS_NUM          0
  70 #define SPD_EEPROM_ADDRESS              0x52 /* I2C access */
  71
  72 #define CONFIG_MEM_INIT_VALUE           0xDeadBeef
  73
  74 #ifndef __ASSEMBLY__
  75 extern unsigned long get_sdram_size(void);
  76 #endif
  77 #define CONFIG_SYS_SDRAM_SIZE           get_sdram_size() /* DDR size */
  78 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  79 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  80
  81 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  82 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  83
  84 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
  85 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
  86 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
  87
  88 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
  89 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
  90 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
  91 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
  92
  93 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
  94 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
  95 #define CONFIG_SYS_DDR_RCW_1            0x00000000
  96 #define CONFIG_SYS_DDR_RCW_2            0x00000000
  97 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3  */
  98 #define CONFIG_SYS_DDR_CONTROL_2        0x24401000
  99 #define CONFIG_SYS_DDR_TIMING_4         0x00000001
 100 #define CONFIG_SYS_DDR_TIMING_5         0x02401400
 101
 102 #define CONFIG_SYS_DDR_TIMING_3_800             0x00030000
 103 #define CONFIG_SYS_DDR_TIMING_0_800             0x00110104
 104 #define CONFIG_SYS_DDR_TIMING_1_800             0x6f6b8644
 105 #define CONFIG_SYS_DDR_TIMING_2_800             0x0fa888cf
 106 #define CONFIG_SYS_DDR_CLK_CTRL_800             0x03000000
 107 #define CONFIG_SYS_DDR_MODE_1_800               0x00441420
 108 #define CONFIG_SYS_DDR_MODE_2_800               0x8000c000
 109 #define CONFIG_SYS_DDR_INTERVAL_800             0x0c300100
 110 #define CONFIG_SYS_DDR_WRLVL_CONTROL_800        0x8675f608
 111
 112 /*
 113  * Base addresses -- Note these are effective addresses where the
 114  * actual resources get mapped (not physical addresses)
 115  */
 116 /* relocated CCSRBAR */
 117 #define CONFIG_SYS_CCSRBAR      CONFIG_SYS_CCSRBAR_DEFAULT
 118 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR_DEFAULT
 119
 120 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses */
 121                                                         /* CONFIG_SYS_IMMR */
 122 /* DSP CCSRBAR */
 123 #define CONFIG_SYS_FSL_DSP_CCSRBAR      CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 124 #define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 125
 126 /*
 127  * Memory map
 128  *
 129  * 0x0000_0000  0x3FFF_FFFF     DDR                     1G cacheable
 130  * 0x8800_0000  0x8810_0000     IFC internal SRAM               1M
 131  * 0xB000_0000  0xB0FF_FFFF     DSP core M2 memory      16M
 132  * 0xC100_0000  0xC13F_FFFF     MAPLE-2F                4M
 133  * 0xC1F0_0000  0xC1F3_FFFF     PA L2 SRAM Region 0     256K
 134  * 0xC1F8_0000  0xC1F9_FFFF     PA L2 SRAM Region 1     128K
 135  * 0xFED0_0000  0xFED0_3FFF     SEC Secured RAM         16K
 136  * 0xFF60_0000  0xFF6F_FFFF     DSP CCSR                1M
 137  * 0xFF70_0000  0xFF7F_FFFF     PA CCSR                 1M
 138  * 0xFF80_0000  0xFFFF_FFFF     Boot Page & NAND flash buffer   8M
 139  *
 140  */
 141
 142 /*
 143  * IFC Definitions
 144  */
 145
 146 /* NAND Flash on IFC */
 147 #define CONFIG_SYS_NAND_BASE            0xff800000
 148 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 149
 150 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 151                                 | CSPR_PORT_SIZE_8      /* Port Size = 8 bit*/ \
 152                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 153                                 | CSPR_V)
 154 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 155
 156 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 157                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 158                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 159                                 | CSOR_NAND_RAL_2       /* RAL = 2Byes */ \
 160                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 161                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */ \
 162                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 163
 164 /* NAND Flash Timing Params */
 165 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x03)  \
 166                                         | FTIM0_NAND_TWP(0x05)   \
 167                                         | FTIM0_NAND_TWCHT(0x02) \
 168                                         | FTIM0_NAND_TWH(0x04))
 169 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x1C) \
 170                                         | FTIM1_NAND_TWBE(0x1E) \
 171                                         | FTIM1_NAND_TRR(0x07)  \
 172                                         | FTIM1_NAND_TRP(0x05))
 173 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x08)  \
 174                                         | FTIM2_NAND_TREH(0x04) \
 175                                         | FTIM2_NAND_TWHRE(0x11))
 176 #define CONFIG_SYS_NAND_FTIM3           FTIM3_NAND_TWW(0x04)
 177
 178 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 179 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 180 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 181
 182 #define CONFIG_SYS_NAND_DDR_LAW         11
 183
 184 /* Set up IFC registers for boot location NAND */
 185 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 186 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 187 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 188 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 189 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 190 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 191 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 192
 193 #define CONFIG_SYS_INIT_RAM_LOCK
 194 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* stack in RAM */
 195 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000/* End of used area in RAM */
 196
 197 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE \
 198                                                 - GENERATED_GBL_DATA_SIZE)
 199 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 200
 201 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 202 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc*/
 203
 204 /* Serial Port */
 205 #undef  CONFIG_SERIAL_SOFTWARE_FIFO
 206 #define CONFIG_SYS_NS16550_SERIAL
 207 #define CONFIG_SYS_NS16550_REG_SIZE     1
 208 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 209 #ifdef CONFIG_SPL_BUILD
 210 #define CONFIG_NS16550_MIN_FUNCTIONS
 211 #endif
 212
 213 #define CONFIG_SYS_BAUDRATE_TABLE       \
 214         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 215
 216 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 217
 218 #define CONFIG_SYS_I2C
 219 #define CONFIG_SYS_I2C_FSL
 220 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 221 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 222 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 223
 224 /* I2C EEPROM */
 225 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 226 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 227 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 228
 229 /* eSPI - Enhanced SPI */
 230 #ifdef CONFIG_FSL_ESPI
 231 #define CONFIG_SF_DEFAULT_SPEED         10000000
 232 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 233 #endif
 234
 235 #if defined(CONFIG_TSEC_ENET)
 236
 237 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 238 #define CONFIG_TSEC1    1
 239 #define CONFIG_TSEC1_NAME       "eTSEC1"
 240 #define CONFIG_TSEC2    1
 241 #define CONFIG_TSEC2_NAME       "eTSEC2"
 242
 243 #define TSEC1_PHY_ADDR          0
 244 #define TSEC2_PHY_ADDR          3
 245
 246 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 247 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 248
 249 #define TSEC1_PHYIDX            0
 250
 251 #define TSEC2_PHYIDX            0
 252
 253 #define CONFIG_ETHPRIME         "eTSEC1"
 254
 255 #endif  /* CONFIG_TSEC_ENET */
 256
 257 /*
 258  * Environment
 259  */
 260 #if defined(CONFIG_RAMBOOT_SPIFLASH)
 261 #define CONFIG_ENV_SPI_BUS      0
 262 #define CONFIG_ENV_SPI_CS       0
 263 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 264 #define CONFIG_ENV_SPI_MODE     0
 265 #define CONFIG_ENV_OFFSET       0x100000        /* 1MB */
 266 #define CONFIG_ENV_SECT_SIZE    0x10000
 267 #define CONFIG_ENV_SIZE         0x2000
 268 #elif defined(CONFIG_NAND)
 269 #define CONFIG_SYS_EXTRA_ENV_RELOC
 270 #define CONFIG_ENV_SIZE         CONFIG_SYS_NAND_BLOCK_SIZE
 271 #define CONFIG_ENV_OFFSET       ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
 272 #define CONFIG_ENV_RANGE        (3 * CONFIG_ENV_SIZE)
 273 #elif defined(CONFIG_SYS_RAMBOOT)
 274 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 275 #define CONFIG_ENV_SIZE         0x2000
 276 #endif
 277
 278 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 279 #define CONFIG_SYS_LOADS_BAUD_CHANGE            /* allow baudrate change */
 280
 281 /*
 282  * Miscellaneous configurable options
 283  */
 284 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 285
 286 #if defined(CONFIG_CMD_KGDB)
 287 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 288 #else
 289 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 290 #endif
 291 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 292
 293 /*
 294  * For booting Linux, the board info and command line data
 295  * have to be in the first 64 MB of memory, since this is
 296  * the maximum mapped by the Linux kernel during initialization.
 297  */
 298 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20) /* Initial Memory map for Linux */
 299 #define CONFIG_SYS_BOOTM_LEN    (64 << 20) /* Increase max gunzip size */
 300
 301 #if defined(CONFIG_CMD_KGDB)
 302 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 303 #endif
 304
 305 #ifdef CONFIG_USB_EHCI_HCD
 306 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 307 #define CONFIG_USB_EHCI_FSL
 308 #define CONFIG_HAS_FSL_DR_USB
 309 #endif
 310
 311 /*
 312  * Dynamic MTD Partition support with mtdparts
 313  */
 314
 315 /*
 316  * Environment Configuration
 317  */
 318
 319 #if defined(CONFIG_TSEC_ENET)
 320 #define CONFIG_HAS_ETH0
 321 #endif
 322
 323 #define CONFIG_HOSTNAME         "BSC9131rdb"
 324 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 325 #define CONFIG_BOOTFILE         "uImage"
 326 #define CONFIG_UBOOTPATH        "u-boot.bin" /* U-Boot image on TFTP server */
 327
 328 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 329         "netdev=eth0\0"                                         \
 330         "uboot=" CONFIG_UBOOTPATH "\0"                          \
 331         "loadaddr=1000000\0"                    \
 332         "bootfile=uImage\0"     \
 333         "consoledev=ttyS0\0"                            \
 334         "ramdiskaddr=2000000\0"                 \
 335         "ramdiskfile=rootfs.ext2.gz.uboot\0"            \
 336         "fdtaddr=1e00000\0"                             \
 337         "fdtfile=bsc9131rdb.dtb\0"              \
 338         "bdev=sda1\0"   \
 339         "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"    \
 340         "bootm_size=0x37000000\0"       \
 341         "othbootargs=ramdisk_size=600000 " \
 342         "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \
 343         "usbext2boot=setenv bootargs root=/dev/ram rw " \
 344         "console=$consoledev,$baudrate $othbootargs; "  \
 345         "usb start;"                    \
 346         "ext2load usb 0:4 $loadaddr $bootfile;"         \
 347         "ext2load usb 0:4 $fdtaddr $fdtfile;"   \
 348         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"   \
 349         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"       \
 350
 351 #define CONFIG_RAMBOOTCOMMAND           \
 352         "setenv bootargs root=/dev/ram rw "     \
 353         "console=$consoledev,$baudrate $othbootargs; "  \
 354         "tftp $ramdiskaddr $ramdiskfile;"       \
 355         "tftp $loadaddr $bootfile;"             \
 356         "tftp $fdtaddr $fdtfile;"               \
 357         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 358
 359 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
 360
 361 #endif  /* __CONFIG_H */