drivers/usb/phy/phy-ab8500-usb.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * USB transceiver driver for AB8500 family chips
   4  *
   5  * Copyright (C) 2010-2013 ST-Ericsson AB
   6  * Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
   7  * Avinash Kumar <avinash.kumar@stericsson.com>
   8  * Thirupathi Chippakurthy <thirupathi.chippakurthy@stericsson.com>
   9  */
  10
  11 #include <linux/module.h>
  12 #include <linux/platform_device.h>
  13 #include <linux/usb/otg.h>
  14 #include <linux/slab.h>
  15 #include <linux/notifier.h>
  16 #include <linux/interrupt.h>
  17 #include <linux/delay.h>
  18 #include <linux/clk.h>
  19 #include <linux/err.h>
  20 #include <linux/mfd/abx500.h>
  21 #include <linux/mfd/abx500/ab8500.h>
  22 #include <linux/usb/musb-ux500.h>
  23 #include <linux/regulator/consumer.h>
  24 #include <linux/pinctrl/consumer.h>
  25
  26 /* Bank AB8500_SYS_CTRL2_BLOCK */
  27 #define AB8500_MAIN_WD_CTRL_REG 0x01
  28
  29 /* Bank AB8500_USB */
  30 #define AB8500_USB_LINE_STAT_REG 0x80
  31 #define AB8505_USB_LINE_STAT_REG 0x94
  32 #define AB8500_USB_PHY_CTRL_REG 0x8A
  33
  34 /* Bank AB8500_DEVELOPMENT */
  35 #define AB8500_BANK12_ACCESS 0x00
  36
  37 /* Bank AB8500_DEBUG */
  38 #define AB8500_USB_PHY_TUNE1 0x05
  39 #define AB8500_USB_PHY_TUNE2 0x06
  40 #define AB8500_USB_PHY_TUNE3 0x07
  41
  42 /* Bank AB8500_INTERRUPT */
  43 #define AB8500_IT_SOURCE2_REG 0x01
  44
  45 #define AB8500_BIT_OTG_STAT_ID (1 << 0)
  46 #define AB8500_BIT_PHY_CTRL_HOST_EN (1 << 0)
  47 #define AB8500_BIT_PHY_CTRL_DEVICE_EN (1 << 1)
  48 #define AB8500_BIT_WD_CTRL_ENABLE (1 << 0)
  49 #define AB8500_BIT_WD_CTRL_KICK (1 << 1)
  50 #define AB8500_BIT_SOURCE2_VBUSDET (1 << 7)
  51
  52 #define AB8500_WD_KICK_DELAY_US 100 /* usec */
  53 #define AB8500_WD_V11_DISABLE_DELAY_US 100 /* usec */
  54 #define AB8500_V20_31952_DISABLE_DELAY_US 100 /* usec */
  55
  56 /* Usb line status register */
  57 enum ab8500_usb_link_status {
  58         USB_LINK_NOT_CONFIGURED_8500 = 0,
  59         USB_LINK_STD_HOST_NC_8500,
  60         USB_LINK_STD_HOST_C_NS_8500,
  61         USB_LINK_STD_HOST_C_S_8500,
  62         USB_LINK_HOST_CHG_NM_8500,
  63         USB_LINK_HOST_CHG_HS_8500,
  64         USB_LINK_HOST_CHG_HS_CHIRP_8500,
  65         USB_LINK_DEDICATED_CHG_8500,
  66         USB_LINK_ACA_RID_A_8500,
  67         USB_LINK_ACA_RID_B_8500,
  68         USB_LINK_ACA_RID_C_NM_8500,
  69         USB_LINK_ACA_RID_C_HS_8500,
  70         USB_LINK_ACA_RID_C_HS_CHIRP_8500,
  71         USB_LINK_HM_IDGND_8500,
  72         USB_LINK_RESERVED_8500,
  73         USB_LINK_NOT_VALID_LINK_8500,
  74 };
  75
  76 enum ab8505_usb_link_status {
  77         USB_LINK_NOT_CONFIGURED_8505 = 0,
  78         USB_LINK_STD_HOST_NC_8505,
  79         USB_LINK_STD_HOST_C_NS_8505,
  80         USB_LINK_STD_HOST_C_S_8505,
  81         USB_LINK_CDP_8505,
  82         USB_LINK_RESERVED0_8505,
  83         USB_LINK_RESERVED1_8505,
  84         USB_LINK_DEDICATED_CHG_8505,
  85         USB_LINK_ACA_RID_A_8505,
  86         USB_LINK_ACA_RID_B_8505,
  87         USB_LINK_ACA_RID_C_NM_8505,
  88         USB_LINK_RESERVED2_8505,
  89         USB_LINK_RESERVED3_8505,
  90         USB_LINK_HM_IDGND_8505,
  91         USB_LINK_CHARGERPORT_NOT_OK_8505,
  92         USB_LINK_CHARGER_DM_HIGH_8505,
  93         USB_LINK_PHYEN_NO_VBUS_NO_IDGND_8505,
  94         USB_LINK_STD_UPSTREAM_NO_IDGNG_NO_VBUS_8505,
  95         USB_LINK_STD_UPSTREAM_8505,
  96         USB_LINK_CHARGER_SE1_8505,
  97         USB_LINK_CARKIT_CHGR_1_8505,
  98         USB_LINK_CARKIT_CHGR_2_8505,
  99         USB_LINK_ACA_DOCK_CHGR_8505,
 100         USB_LINK_SAMSUNG_BOOT_CBL_PHY_EN_8505,
 101         USB_LINK_SAMSUNG_BOOT_CBL_PHY_DISB_8505,
 102         USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8505,
 103         USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8505,
 104         USB_LINK_MOTOROLA_FACTORY_CBL_PHY_EN_8505,
 105 };
 106
 107 enum ab8500_usb_mode {
 108         USB_IDLE = 0,
 109         USB_PERIPHERAL,
 110         USB_HOST,
 111         USB_DEDICATED_CHG
 112 };
 113
 114 /* Register USB_LINK_STATUS interrupt */
 115 #define AB8500_USB_FLAG_USE_LINK_STATUS_IRQ     (1 << 0)
 116 /* Register ID_WAKEUP_F interrupt */
 117 #define AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ       (1 << 1)
 118 /* Register VBUS_DET_F interrupt */
 119 #define AB8500_USB_FLAG_USE_VBUS_DET_IRQ        (1 << 2)
 120 /* Driver is using the ab-iddet driver*/
 121 #define AB8500_USB_FLAG_USE_AB_IDDET            (1 << 3)
 122 /* Enable setting regulators voltage */
 123 #define AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE   (1 << 4)
 124
 125 struct ab8500_usb {
 126         struct usb_phy phy;
 127         struct device *dev;
 128         struct ab8500 *ab8500;
 129         unsigned vbus_draw;
 130         struct work_struct phy_dis_work;
 131         enum ab8500_usb_mode mode;
 132         struct clk *sysclk;
 133         struct regulator *v_ape;
 134         struct regulator *v_musb;
 135         struct regulator *v_ulpi;
 136         int saved_v_ulpi;
 137         int previous_link_status_state;
 138         struct pinctrl *pinctrl;
 139         struct pinctrl_state *pins_sleep;
 140         bool enabled_charging_detection;
 141         unsigned int flags;
 142 };
 143
 144 static inline struct ab8500_usb *phy_to_ab(struct usb_phy *x)
 145 {
 146         return container_of(x, struct ab8500_usb, phy);
 147 }
 148
 149 static void ab8500_usb_wd_workaround(struct ab8500_usb *ab)
 150 {
 151         abx500_set_register_interruptible(ab->dev,
 152                 AB8500_SYS_CTRL2_BLOCK,
 153                 AB8500_MAIN_WD_CTRL_REG,
 154                 AB8500_BIT_WD_CTRL_ENABLE);
 155
 156         udelay(AB8500_WD_KICK_DELAY_US);
 157
 158         abx500_set_register_interruptible(ab->dev,
 159                 AB8500_SYS_CTRL2_BLOCK,
 160                 AB8500_MAIN_WD_CTRL_REG,
 161                 (AB8500_BIT_WD_CTRL_ENABLE
 162                 | AB8500_BIT_WD_CTRL_KICK));
 163
 164         udelay(AB8500_WD_V11_DISABLE_DELAY_US);
 165
 166         abx500_set_register_interruptible(ab->dev,
 167                 AB8500_SYS_CTRL2_BLOCK,
 168                 AB8500_MAIN_WD_CTRL_REG,
 169                 0);
 170 }
 171
 172 static void ab8500_usb_regulator_enable(struct ab8500_usb *ab)
 173 {
 174         int ret, volt;
 175
 176         ret = regulator_enable(ab->v_ape);
 177         if (ret)
 178                 dev_err(ab->dev, "Failed to enable v-ape\n");
 179
 180         if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) {
 181                 ab->saved_v_ulpi = regulator_get_voltage(ab->v_ulpi);
 182                 if (ab->saved_v_ulpi < 0)
 183                         dev_err(ab->dev, "Failed to get v_ulpi voltage\n");
 184
 185                 ret = regulator_set_voltage(ab->v_ulpi, 1300000, 1350000);
 186                 if (ret < 0)
 187                         dev_err(ab->dev, "Failed to set the Vintcore to 1.3V, ret=%d\n",
 188                                         ret);
 189
 190                 ret = regulator_set_load(ab->v_ulpi, 28000);
 191                 if (ret < 0)
 192                         dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n",
 193                                         ret);
 194         }
 195
 196         ret = regulator_enable(ab->v_ulpi);
 197         if (ret)
 198                 dev_err(ab->dev, "Failed to enable vddulpivio18\n");
 199
 200         if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) {
 201                 volt = regulator_get_voltage(ab->v_ulpi);
 202                 if ((volt != 1300000) && (volt != 1350000))
 203                         dev_err(ab->dev, "Vintcore is not set to 1.3V volt=%d\n",
 204                                         volt);
 205         }
 206
 207         ret = regulator_enable(ab->v_musb);
 208         if (ret)
 209                 dev_err(ab->dev, "Failed to enable musb_1v8\n");
 210 }
 211
 212 static void ab8500_usb_regulator_disable(struct ab8500_usb *ab)
 213 {
 214         int ret;
 215
 216         regulator_disable(ab->v_musb);
 217
 218         regulator_disable(ab->v_ulpi);
 219
 220         /* USB is not the only consumer of Vintcore, restore old settings */
 221         if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) {
 222                 if (ab->saved_v_ulpi > 0) {
 223                         ret = regulator_set_voltage(ab->v_ulpi,
 224                                         ab->saved_v_ulpi, ab->saved_v_ulpi);
 225                         if (ret < 0)
 226                                 dev_err(ab->dev, "Failed to set the Vintcore to %duV, ret=%d\n",
 227                                                 ab->saved_v_ulpi, ret);
 228                 }
 229
 230                 ret = regulator_set_load(ab->v_ulpi, 0);
 231                 if (ret < 0)
 232                         dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n",
 233                                         ret);
 234         }
 235
 236         regulator_disable(ab->v_ape);
 237 }
 238
 239 static void ab8500_usb_wd_linkstatus(struct ab8500_usb *ab, u8 bit)
 240 {
 241         /* Workaround for v2.0 bug # 31952 */
 242         if (is_ab8500_2p0(ab->ab8500)) {
 243                 abx500_mask_and_set_register_interruptible(ab->dev,
 244                                 AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 245                                 bit, bit);
 246                 udelay(AB8500_V20_31952_DISABLE_DELAY_US);
 247         }
 248 }
 249
 250 static void ab8500_usb_phy_enable(struct ab8500_usb *ab, bool sel_host)
 251 {
 252         u8 bit;
 253         bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN :
 254                 AB8500_BIT_PHY_CTRL_DEVICE_EN;
 255
 256         /* mux and configure USB pins to DEFAULT state */
 257         ab->pinctrl = pinctrl_get_select(ab->dev, PINCTRL_STATE_DEFAULT);
 258         if (IS_ERR(ab->pinctrl))
 259                 dev_err(ab->dev, "could not get/set default pinstate\n");
 260
 261         if (clk_prepare_enable(ab->sysclk))
 262                 dev_err(ab->dev, "can't prepare/enable clock\n");
 263
 264         ab8500_usb_regulator_enable(ab);
 265
 266         abx500_mask_and_set_register_interruptible(ab->dev,
 267                         AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 268                         bit, bit);
 269 }
 270
 271 static void ab8500_usb_phy_disable(struct ab8500_usb *ab, bool sel_host)
 272 {
 273         u8 bit;
 274         bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN :
 275                 AB8500_BIT_PHY_CTRL_DEVICE_EN;
 276
 277         ab8500_usb_wd_linkstatus(ab, bit);
 278
 279         abx500_mask_and_set_register_interruptible(ab->dev,
 280                         AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 281                         bit, 0);
 282
 283         /* Needed to disable the phy.*/
 284         ab8500_usb_wd_workaround(ab);
 285
 286         clk_disable_unprepare(ab->sysclk);
 287
 288         ab8500_usb_regulator_disable(ab);
 289
 290         if (!IS_ERR(ab->pinctrl)) {
 291                 /* configure USB pins to SLEEP state */
 292                 ab->pins_sleep = pinctrl_lookup_state(ab->pinctrl,
 293                                 PINCTRL_STATE_SLEEP);
 294
 295                 if (IS_ERR(ab->pins_sleep))
 296                         dev_dbg(ab->dev, "could not get sleep pinstate\n");
 297                 else if (pinctrl_select_state(ab->pinctrl, ab->pins_sleep))
 298                         dev_err(ab->dev, "could not set pins to sleep state\n");
 299
 300                 /*
 301                  * as USB pins are shared with iddet, release them to allow
 302                  * iddet to request them
 303                  */
 304                 pinctrl_put(ab->pinctrl);
 305         }
 306 }
 307
 308 #define ab8500_usb_host_phy_en(ab)      ab8500_usb_phy_enable(ab, true)
 309 #define ab8500_usb_host_phy_dis(ab)     ab8500_usb_phy_disable(ab, true)
 310 #define ab8500_usb_peri_phy_en(ab)      ab8500_usb_phy_enable(ab, false)
 311 #define ab8500_usb_peri_phy_dis(ab)     ab8500_usb_phy_disable(ab, false)
 312
 313 static int ab8505_usb_link_status_update(struct ab8500_usb *ab,
 314                 enum ab8505_usb_link_status lsts)
 315 {
 316         enum ux500_musb_vbus_id_status event = 0;
 317
 318         dev_dbg(ab->dev, "ab8505_usb_link_status_update %d\n", lsts);
 319
 320         /*
 321          * Spurious link_status interrupts are seen at the time of
 322          * disconnection of a device in RIDA state
 323          */
 324         if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8505 &&
 325                         (lsts == USB_LINK_STD_HOST_NC_8505))
 326                 return 0;
 327
 328         ab->previous_link_status_state = lsts;
 329
 330         switch (lsts) {
 331         case USB_LINK_ACA_RID_B_8505:
 332                 event = UX500_MUSB_RIDB;
 333         case USB_LINK_NOT_CONFIGURED_8505:
 334         case USB_LINK_RESERVED0_8505:
 335         case USB_LINK_RESERVED1_8505:
 336         case USB_LINK_RESERVED2_8505:
 337         case USB_LINK_RESERVED3_8505:
 338                 ab->mode = USB_IDLE;
 339                 ab->phy.otg->default_a = false;
 340                 ab->vbus_draw = 0;
 341                 if (event != UX500_MUSB_RIDB)
 342                         event = UX500_MUSB_NONE;
 343                 /*
 344                  * Fallback to default B_IDLE as nothing
 345                  * is connected
 346                  */
 347                 ab->phy.otg->state = OTG_STATE_B_IDLE;
 348                 usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
 349                 break;
 350
 351         case USB_LINK_ACA_RID_C_NM_8505:
 352                 event = UX500_MUSB_RIDC;
 353         case USB_LINK_STD_HOST_NC_8505:
 354         case USB_LINK_STD_HOST_C_NS_8505:
 355         case USB_LINK_STD_HOST_C_S_8505:
 356         case USB_LINK_CDP_8505:
 357                 if (ab->mode == USB_IDLE) {
 358                         ab->mode = USB_PERIPHERAL;
 359                         ab8500_usb_peri_phy_en(ab);
 360                         atomic_notifier_call_chain(&ab->phy.notifier,
 361                                         UX500_MUSB_PREPARE, &ab->vbus_draw);
 362                         usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED);
 363                 }
 364                 if (event != UX500_MUSB_RIDC)
 365                         event = UX500_MUSB_VBUS;
 366                 break;
 367
 368         case USB_LINK_ACA_RID_A_8505:
 369         case USB_LINK_ACA_DOCK_CHGR_8505:
 370                 event = UX500_MUSB_RIDA;
 371         case USB_LINK_HM_IDGND_8505:
 372                 if (ab->mode == USB_IDLE) {
 373                         ab->mode = USB_HOST;
 374                         ab8500_usb_host_phy_en(ab);
 375                         atomic_notifier_call_chain(&ab->phy.notifier,
 376                                         UX500_MUSB_PREPARE, &ab->vbus_draw);
 377                 }
 378                 ab->phy.otg->default_a = true;
 379                 if (event != UX500_MUSB_RIDA)
 380                         event = UX500_MUSB_ID;
 381                 atomic_notifier_call_chain(&ab->phy.notifier,
 382                                 event, &ab->vbus_draw);
 383                 break;
 384
 385         case USB_LINK_DEDICATED_CHG_8505:
 386                 ab->mode = USB_DEDICATED_CHG;
 387                 event = UX500_MUSB_CHARGER;
 388                 atomic_notifier_call_chain(&ab->phy.notifier,
 389                                 event, &ab->vbus_draw);
 390                 usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER);
 391                 break;
 392
 393         default:
 394                 break;
 395         }
 396
 397         return 0;
 398 }
 399
 400 static int ab8500_usb_link_status_update(struct ab8500_usb *ab,
 401                 enum ab8500_usb_link_status lsts)
 402 {
 403         enum ux500_musb_vbus_id_status event = 0;
 404
 405         dev_dbg(ab->dev, "ab8500_usb_link_status_update %d\n", lsts);
 406
 407         /*
 408          * Spurious link_status interrupts are seen in case of a
 409          * disconnection of a device in IDGND and RIDA stage
 410          */
 411         if (ab->previous_link_status_state == USB_LINK_HM_IDGND_8500 &&
 412                         (lsts == USB_LINK_STD_HOST_C_NS_8500 ||
 413                          lsts == USB_LINK_STD_HOST_NC_8500))
 414                 return 0;
 415
 416         if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8500 &&
 417                         lsts == USB_LINK_STD_HOST_NC_8500)
 418                 return 0;
 419
 420         ab->previous_link_status_state = lsts;
 421
 422         switch (lsts) {
 423         case USB_LINK_ACA_RID_B_8500:
 424                 event = UX500_MUSB_RIDB;
 425         case USB_LINK_NOT_CONFIGURED_8500:
 426         case USB_LINK_NOT_VALID_LINK_8500:
 427                 ab->mode = USB_IDLE;
 428                 ab->phy.otg->default_a = false;
 429                 ab->vbus_draw = 0;
 430                 if (event != UX500_MUSB_RIDB)
 431                         event = UX500_MUSB_NONE;
 432                 /* Fallback to default B_IDLE as nothing is connected */
 433                 ab->phy.otg->state = OTG_STATE_B_IDLE;
 434                 usb_phy_set_event(&ab->phy, USB_EVENT_NONE);
 435                 break;
 436
 437         case USB_LINK_ACA_RID_C_NM_8500:
 438         case USB_LINK_ACA_RID_C_HS_8500:
 439         case USB_LINK_ACA_RID_C_HS_CHIRP_8500:
 440                 event = UX500_MUSB_RIDC;
 441         case USB_LINK_STD_HOST_NC_8500:
 442         case USB_LINK_STD_HOST_C_NS_8500:
 443         case USB_LINK_STD_HOST_C_S_8500:
 444         case USB_LINK_HOST_CHG_NM_8500:
 445         case USB_LINK_HOST_CHG_HS_8500:
 446         case USB_LINK_HOST_CHG_HS_CHIRP_8500:
 447                 if (ab->mode == USB_IDLE) {
 448                         ab->mode = USB_PERIPHERAL;
 449                         ab8500_usb_peri_phy_en(ab);
 450                         atomic_notifier_call_chain(&ab->phy.notifier,
 451                                         UX500_MUSB_PREPARE, &ab->vbus_draw);
 452                         usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED);
 453                 }
 454                 if (event != UX500_MUSB_RIDC)
 455                         event = UX500_MUSB_VBUS;
 456                 break;
 457
 458         case USB_LINK_ACA_RID_A_8500:
 459                 event = UX500_MUSB_RIDA;
 460         case USB_LINK_HM_IDGND_8500:
 461                 if (ab->mode == USB_IDLE) {
 462                         ab->mode = USB_HOST;
 463                         ab8500_usb_host_phy_en(ab);
 464                         atomic_notifier_call_chain(&ab->phy.notifier,
 465                                         UX500_MUSB_PREPARE, &ab->vbus_draw);
 466                 }
 467                 ab->phy.otg->default_a = true;
 468                 if (event != UX500_MUSB_RIDA)
 469                         event = UX500_MUSB_ID;
 470                 atomic_notifier_call_chain(&ab->phy.notifier,
 471                                 event, &ab->vbus_draw);
 472                 break;
 473
 474         case USB_LINK_DEDICATED_CHG_8500:
 475                 ab->mode = USB_DEDICATED_CHG;
 476                 event = UX500_MUSB_CHARGER;
 477                 atomic_notifier_call_chain(&ab->phy.notifier,
 478                                 event, &ab->vbus_draw);
 479                 usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER);
 480                 break;
 481
 482         case USB_LINK_RESERVED_8500:
 483                 break;
 484         }
 485
 486         return 0;
 487 }
 488
 489 /*
 490  * Connection Sequence:
 491  *   1. Link Status Interrupt
 492  *   2. Enable AB clock
 493  *   3. Enable AB regulators
 494  *   4. Enable USB phy
 495  *   5. Reset the musb controller
 496  *   6. Switch the ULPI GPIO pins to fucntion mode
 497  *   7. Enable the musb Peripheral5 clock
 498  *   8. Restore MUSB context
 499  */
 500 static int abx500_usb_link_status_update(struct ab8500_usb *ab)
 501 {
 502         u8 reg;
 503         int ret = 0;
 504
 505         if (is_ab8500(ab->ab8500)) {
 506                 enum ab8500_usb_link_status lsts;
 507
 508                 ret = abx500_get_register_interruptible(ab->dev,
 509                                 AB8500_USB, AB8500_USB_LINE_STAT_REG, &reg);
 510                 if (ret < 0)
 511                         return ret;
 512                 lsts = (reg >> 3) & 0x0F;
 513                 ret = ab8500_usb_link_status_update(ab, lsts);
 514         } else if (is_ab8505(ab->ab8500)) {
 515                 enum ab8505_usb_link_status lsts;
 516
 517                 ret = abx500_get_register_interruptible(ab->dev,
 518                                 AB8500_USB, AB8505_USB_LINE_STAT_REG, &reg);
 519                 if (ret < 0)
 520                         return ret;
 521                 lsts = (reg >> 3) & 0x1F;
 522                 ret = ab8505_usb_link_status_update(ab, lsts);
 523         }
 524
 525         return ret;
 526 }
 527
 528 /*
 529  * Disconnection Sequence:
 530  *   1. Disconnect Interrupt
 531  *   2. Disable regulators
 532  *   3. Disable AB clock
 533  *   4. Disable the Phy
 534  *   5. Link Status Interrupt
 535  *   6. Disable Musb Clock
 536  */
 537 static irqreturn_t ab8500_usb_disconnect_irq(int irq, void *data)
 538 {
 539         struct ab8500_usb *ab = (struct ab8500_usb *) data;
 540         enum usb_phy_events event = USB_EVENT_NONE;
 541
 542         /* Link status will not be updated till phy is disabled. */
 543         if (ab->mode == USB_HOST) {
 544                 ab->phy.otg->default_a = false;
 545                 ab->vbus_draw = 0;
 546                 atomic_notifier_call_chain(&ab->phy.notifier,
 547                                 event, &ab->vbus_draw);
 548                 ab8500_usb_host_phy_dis(ab);
 549                 ab->mode = USB_IDLE;
 550         }
 551
 552         if (ab->mode == USB_PERIPHERAL) {
 553                 atomic_notifier_call_chain(&ab->phy.notifier,
 554                                 event, &ab->vbus_draw);
 555                 ab8500_usb_peri_phy_dis(ab);
 556                 atomic_notifier_call_chain(&ab->phy.notifier,
 557                                 UX500_MUSB_CLEAN, &ab->vbus_draw);
 558                 ab->mode = USB_IDLE;
 559                 ab->phy.otg->default_a = false;
 560                 ab->vbus_draw = 0;
 561         }
 562
 563         if (is_ab8500_2p0(ab->ab8500)) {
 564                 if (ab->mode == USB_DEDICATED_CHG) {
 565                         ab8500_usb_wd_linkstatus(ab,
 566                                         AB8500_BIT_PHY_CTRL_DEVICE_EN);
 567                         abx500_mask_and_set_register_interruptible(ab->dev,
 568                                         AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 569                                         AB8500_BIT_PHY_CTRL_DEVICE_EN, 0);
 570                 }
 571         }
 572
 573         return IRQ_HANDLED;
 574 }
 575
 576 static irqreturn_t ab8500_usb_link_status_irq(int irq, void *data)
 577 {
 578         struct ab8500_usb *ab = (struct ab8500_usb *)data;
 579
 580         abx500_usb_link_status_update(ab);
 581
 582         return IRQ_HANDLED;
 583 }
 584
 585 static void ab8500_usb_phy_disable_work(struct work_struct *work)
 586 {
 587         struct ab8500_usb *ab = container_of(work, struct ab8500_usb,
 588                                                 phy_dis_work);
 589
 590         if (!ab->phy.otg->host)
 591                 ab8500_usb_host_phy_dis(ab);
 592
 593         if (!ab->phy.otg->gadget)
 594                 ab8500_usb_peri_phy_dis(ab);
 595 }
 596
 597 static int ab8500_usb_set_suspend(struct usb_phy *x, int suspend)
 598 {
 599         /* TODO */
 600         return 0;
 601 }
 602
 603 static int ab8500_usb_set_peripheral(struct usb_otg *otg,
 604                                         struct usb_gadget *gadget)
 605 {
 606         struct ab8500_usb *ab;
 607
 608         if (!otg)
 609                 return -ENODEV;
 610
 611         ab = phy_to_ab(otg->usb_phy);
 612
 613         ab->phy.otg->gadget = gadget;
 614
 615         /* Some drivers call this function in atomic context.
 616          * Do not update ab8500 registers directly till this
 617          * is fixed.
 618          */
 619
 620         if ((ab->mode != USB_IDLE) && !gadget) {
 621                 ab->mode = USB_IDLE;
 622                 schedule_work(&ab->phy_dis_work);
 623         }
 624
 625         return 0;
 626 }
 627
 628 static int ab8500_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
 629 {
 630         struct ab8500_usb *ab;
 631
 632         if (!otg)
 633                 return -ENODEV;
 634
 635         ab = phy_to_ab(otg->usb_phy);
 636
 637         ab->phy.otg->host = host;
 638
 639         /* Some drivers call this function in atomic context.
 640          * Do not update ab8500 registers directly till this
 641          * is fixed.
 642          */
 643
 644         if ((ab->mode != USB_IDLE) && !host) {
 645                 ab->mode = USB_IDLE;
 646                 schedule_work(&ab->phy_dis_work);
 647         }
 648
 649         return 0;
 650 }
 651
 652 static void ab8500_usb_restart_phy(struct ab8500_usb *ab)
 653 {
 654         abx500_mask_and_set_register_interruptible(ab->dev,
 655                         AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 656                         AB8500_BIT_PHY_CTRL_DEVICE_EN,
 657                         AB8500_BIT_PHY_CTRL_DEVICE_EN);
 658
 659         udelay(100);
 660
 661         abx500_mask_and_set_register_interruptible(ab->dev,
 662                         AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 663                         AB8500_BIT_PHY_CTRL_DEVICE_EN,
 664                         0);
 665
 666         abx500_mask_and_set_register_interruptible(ab->dev,
 667                         AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 668                         AB8500_BIT_PHY_CTRL_HOST_EN,
 669                         AB8500_BIT_PHY_CTRL_HOST_EN);
 670
 671         udelay(100);
 672
 673         abx500_mask_and_set_register_interruptible(ab->dev,
 674                         AB8500_USB, AB8500_USB_PHY_CTRL_REG,
 675                         AB8500_BIT_PHY_CTRL_HOST_EN,
 676                         0);
 677 }
 678
 679 static int ab8500_usb_regulator_get(struct ab8500_usb *ab)
 680 {
 681         int err;
 682
 683         ab->v_ape = devm_regulator_get(ab->dev, "v-ape");
 684         if (IS_ERR(ab->v_ape)) {
 685                 dev_err(ab->dev, "Could not get v-ape supply\n");
 686                 err = PTR_ERR(ab->v_ape);
 687                 return err;
 688         }
 689
 690         ab->v_ulpi = devm_regulator_get(ab->dev, "vddulpivio18");
 691         if (IS_ERR(ab->v_ulpi)) {
 692                 dev_err(ab->dev, "Could not get vddulpivio18 supply\n");
 693                 err = PTR_ERR(ab->v_ulpi);
 694                 return err;
 695         }
 696
 697         ab->v_musb = devm_regulator_get(ab->dev, "musb_1v8");
 698         if (IS_ERR(ab->v_musb)) {
 699                 dev_err(ab->dev, "Could not get musb_1v8 supply\n");
 700                 err = PTR_ERR(ab->v_musb);
 701                 return err;
 702         }
 703
 704         return 0;
 705 }
 706
 707 static int ab8500_usb_irq_setup(struct platform_device *pdev,
 708                 struct ab8500_usb *ab)
 709 {
 710         int err;
 711         int irq;
 712
 713         if (ab->flags & AB8500_USB_FLAG_USE_LINK_STATUS_IRQ) {
 714                 irq = platform_get_irq_byname(pdev, "USB_LINK_STATUS");
 715                 if (irq < 0) {
 716                         dev_err(&pdev->dev, "Link status irq not found\n");
 717                         return irq;
 718                 }
 719                 err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
 720                                 ab8500_usb_link_status_irq,
 721                                 IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
 722                                 "usb-link-status", ab);
 723                 if (err < 0) {
 724                         dev_err(ab->dev, "request_irq failed for link status irq\n");
 725                         return err;
 726                 }
 727         }
 728
 729         if (ab->flags & AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ) {
 730                 irq = platform_get_irq_byname(pdev, "ID_WAKEUP_F");
 731                 if (irq < 0) {
 732                         dev_err(&pdev->dev, "ID fall irq not found\n");
 733                         return irq;
 734                 }
 735                 err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
 736                                 ab8500_usb_disconnect_irq,
 737                                 IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
 738                                 "usb-id-fall", ab);
 739                 if (err < 0) {
 740                         dev_err(ab->dev, "request_irq failed for ID fall irq\n");
 741                         return err;
 742                 }
 743         }
 744
 745         if (ab->flags & AB8500_USB_FLAG_USE_VBUS_DET_IRQ) {
 746                 irq = platform_get_irq_byname(pdev, "VBUS_DET_F");
 747                 if (irq < 0) {
 748                         dev_err(&pdev->dev, "VBUS fall irq not found\n");
 749                         return irq;
 750                 }
 751                 err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
 752                                 ab8500_usb_disconnect_irq,
 753                                 IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
 754                                 "usb-vbus-fall", ab);
 755                 if (err < 0) {
 756                         dev_err(ab->dev, "request_irq failed for Vbus fall irq\n");
 757                         return err;
 758                 }
 759         }
 760
 761         return 0;
 762 }
 763
 764 static void ab8500_usb_set_ab8500_tuning_values(struct ab8500_usb *ab)
 765 {
 766         int err;
 767
 768         /* Enable the PBT/Bank 0x12 access */
 769         err = abx500_set_register_interruptible(ab->dev,
 770                         AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x01);
 771         if (err < 0)
 772                 dev_err(ab->dev, "Failed to enable bank12 access err=%d\n",
 773                                 err);
 774
 775         err = abx500_set_register_interruptible(ab->dev,
 776                         AB8500_DEBUG, AB8500_USB_PHY_TUNE1, 0xC8);
 777         if (err < 0)
 778                 dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n",
 779                                 err);
 780
 781         err = abx500_set_register_interruptible(ab->dev,
 782                         AB8500_DEBUG, AB8500_USB_PHY_TUNE2, 0x00);
 783         if (err < 0)
 784                 dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n",
 785                                 err);
 786
 787         err = abx500_set_register_interruptible(ab->dev,
 788                         AB8500_DEBUG, AB8500_USB_PHY_TUNE3, 0x78);
 789         if (err < 0)
 790                 dev_err(ab->dev, "Failed to set PHY_TUNE3 register err=%d\n",
 791                                 err);
 792
 793         /* Switch to normal mode/disable Bank 0x12 access */
 794         err = abx500_set_register_interruptible(ab->dev,
 795                         AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x00);
 796         if (err < 0)
 797                 dev_err(ab->dev, "Failed to switch bank12 access err=%d\n",
 798                                 err);
 799 }
 800
 801 static void ab8500_usb_set_ab8505_tuning_values(struct ab8500_usb *ab)
 802 {
 803         int err;
 804
 805         /* Enable the PBT/Bank 0x12 access */
 806         err = abx500_mask_and_set_register_interruptible(ab->dev,
 807                         AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS,
 808                         0x01, 0x01);
 809         if (err < 0)
 810                 dev_err(ab->dev, "Failed to enable bank12 access err=%d\n",
 811                                 err);
 812
 813         err = abx500_mask_and_set_register_interruptible(ab->dev,
 814                         AB8500_DEBUG, AB8500_USB_PHY_TUNE1,
 815                         0xC8, 0xC8);
 816         if (err < 0)
 817                 dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n",
 818                                 err);
 819
 820         err = abx500_mask_and_set_register_interruptible(ab->dev,
 821                         AB8500_DEBUG, AB8500_USB_PHY_TUNE2,
 822                         0x60, 0x60);
 823         if (err < 0)
 824                 dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n",
 825                                 err);
 826
 827         err = abx500_mask_and_set_register_interruptible(ab->dev,
 828                         AB8500_DEBUG, AB8500_USB_PHY_TUNE3,
 829                         0xFC, 0x80);
 830
 831         if (err < 0)
 832                 dev_err(ab->dev, "Failed to set PHY_TUNE3 register err=%d\n",
 833                                 err);
 834
 835         /* Switch to normal mode/disable Bank 0x12 access */
 836         err = abx500_mask_and_set_register_interruptible(ab->dev,
 837                         AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS,
 838                         0x00, 0x00);
 839         if (err < 0)
 840                 dev_err(ab->dev, "Failed to switch bank12 access err=%d\n",
 841                                 err);
 842 }
 843
 844 static int ab8500_usb_probe(struct platform_device *pdev)
 845 {
 846         struct ab8500_usb       *ab;
 847         struct ab8500           *ab8500;
 848         struct usb_otg          *otg;
 849         int err;
 850         int rev;
 851
 852         ab8500 = dev_get_drvdata(pdev->dev.parent);
 853         rev = abx500_get_chip_id(&pdev->dev);
 854
 855         if (is_ab8500_1p1_or_earlier(ab8500)) {
 856                 dev_err(&pdev->dev, "Unsupported AB8500 chip rev=%d\n", rev);
 857                 return -ENODEV;
 858         }
 859
 860         ab = devm_kzalloc(&pdev->dev, sizeof(*ab), GFP_KERNEL);
 861         if (!ab)
 862                 return -ENOMEM;
 863
 864         otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
 865         if (!otg)
 866                 return -ENOMEM;
 867
 868         ab->dev                 = &pdev->dev;
 869         ab->ab8500              = ab8500;
 870         ab->phy.dev             = ab->dev;
 871         ab->phy.otg             = otg;
 872         ab->phy.label           = "ab8500";
 873         ab->phy.set_suspend     = ab8500_usb_set_suspend;
 874         ab->phy.otg->state      = OTG_STATE_UNDEFINED;
 875
 876         otg->usb_phy            = &ab->phy;
 877         otg->set_host           = ab8500_usb_set_host;
 878         otg->set_peripheral     = ab8500_usb_set_peripheral;
 879
 880         if (is_ab8500(ab->ab8500)) {
 881                 ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ |
 882                         AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ |
 883                         AB8500_USB_FLAG_USE_VBUS_DET_IRQ |
 884                         AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
 885         } else if (is_ab8505(ab->ab8500)) {
 886                 ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ |
 887                         AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ |
 888                         AB8500_USB_FLAG_USE_VBUS_DET_IRQ |
 889                         AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
 890         }
 891
 892         /* Disable regulator voltage setting for AB8500 <= v2.0 */
 893         if (is_ab8500_2p0_or_earlier(ab->ab8500))
 894                 ab->flags &= ~AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE;
 895
 896         platform_set_drvdata(pdev, ab);
 897
 898         /* all: Disable phy when called from set_host and set_peripheral */
 899         INIT_WORK(&ab->phy_dis_work, ab8500_usb_phy_disable_work);
 900
 901         err = ab8500_usb_regulator_get(ab);
 902         if (err)
 903                 return err;
 904
 905         ab->sysclk = devm_clk_get(ab->dev, "sysclk");
 906         if (IS_ERR(ab->sysclk)) {
 907                 dev_err(ab->dev, "Could not get sysclk.\n");
 908                 return PTR_ERR(ab->sysclk);
 909         }
 910
 911         err = ab8500_usb_irq_setup(pdev, ab);
 912         if (err < 0)
 913                 return err;
 914
 915         err = usb_add_phy(&ab->phy, USB_PHY_TYPE_USB2);
 916         if (err) {
 917                 dev_err(&pdev->dev, "Can't register transceiver\n");
 918                 return err;
 919         }
 920
 921         if (is_ab8500(ab->ab8500) && !is_ab8500_2p0_or_earlier(ab->ab8500))
 922                 /* Phy tuning values for AB8500 > v2.0 */
 923                 ab8500_usb_set_ab8500_tuning_values(ab);
 924         else if (is_ab8505(ab->ab8500))
 925                 /* Phy tuning values for AB8505 */
 926                 ab8500_usb_set_ab8505_tuning_values(ab);
 927
 928         /* Needed to enable ID detection. */
 929         ab8500_usb_wd_workaround(ab);
 930
 931         /*
 932          * This is required for usb-link-status to work properly when a
 933          * cable is connected at boot time.
 934          */
 935         ab8500_usb_restart_phy(ab);
 936
 937         abx500_usb_link_status_update(ab);
 938
 939         dev_info(&pdev->dev, "revision 0x%2x driver initialized\n", rev);
 940
 941         return 0;
 942 }
 943
 944 static int ab8500_usb_remove(struct platform_device *pdev)
 945 {
 946         struct ab8500_usb *ab = platform_get_drvdata(pdev);
 947
 948         cancel_work_sync(&ab->phy_dis_work);
 949
 950         usb_remove_phy(&ab->phy);
 951
 952         if (ab->mode == USB_HOST)
 953                 ab8500_usb_host_phy_dis(ab);
 954         else if (ab->mode == USB_PERIPHERAL)
 955                 ab8500_usb_peri_phy_dis(ab);
 956
 957         return 0;
 958 }
 959
 960 static const struct platform_device_id ab8500_usb_devtype[] = {
 961         { .name = "ab8500-usb", },
 962         { /* sentinel */ }
 963 };
 964 MODULE_DEVICE_TABLE(platform, ab8500_usb_devtype);
 965
 966 static struct platform_driver ab8500_usb_driver = {
 967         .probe          = ab8500_usb_probe,
 968         .remove         = ab8500_usb_remove,
 969         .id_table       = ab8500_usb_devtype,
 970         .driver         = {
 971                 .name   = "abx5x0-usb",
 972         },
 973 };
 974
 975 static int __init ab8500_usb_init(void)
 976 {
 977         return platform_driver_register(&ab8500_usb_driver);
 978 }
 979 subsys_initcall(ab8500_usb_init);
 980
 981 static void __exit ab8500_usb_exit(void)
 982 {
 983         platform_driver_unregister(&ab8500_usb_driver);
 984 }
 985 module_exit(ab8500_usb_exit);
 986
 987 MODULE_AUTHOR("ST-Ericsson AB");
 988 MODULE_DESCRIPTION("AB8500 family usb transceiver driver");
 989 MODULE_LICENSE("GPL");