2 * MUSB OTG driver host support
4 * Copyright 2005 Mentor Graphics Corporation
5 * Copyright (C) 2005-2006 by Texas Instruments
6 * Copyright (C) 2006-2007 Nokia Corporation
7 * Copyright (C) 2008-2009 MontaVista Software, Inc. <source@mvista.com>
9 * SPDX-License-Identifier: GPL-2.0
13 #include <linux/module.h>
14 #include <linux/kernel.h>
15 #include <linux/delay.h>
16 #include <linux/sched.h>
17 #include <linux/slab.h>
18 #include <linux/errno.h>
19 #include <linux/init.h>
20 #include <linux/list.h>
21 #include <linux/dma-mapping.h>
25 #include "linux-compat.h"
26 #include "usb-compat.h"
29 #include "musb_core.h"
30 #include "musb_host.h"
33 /* MUSB HOST status 22-mar-2006
35 * - There's still lots of partial code duplication for fault paths, so
36 * they aren't handled as consistently as they need to be.
38 * - PIO mostly behaved when last tested.
39 * + including ep0, with all usbtest cases 9, 10
40 * + usbtest 14 (ep0out) doesn't seem to run at all
41 * + double buffered OUT/TX endpoints saw stalls(!) with certain usbtest
42 * configurations, but otherwise double buffering passes basic tests.
43 * + for 2.6.N, for N > ~10, needs API changes for hcd framework.
45 * - DMA (CPPI) ... partially behaves, not currently recommended
46 * + about 1/15 the speed of typical EHCI implementations (PCI)
47 * + RX, all too often reqpkt seems to misbehave after tx
48 * + TX, no known issues (other than evident silicon issue)
50 * - DMA (Mentor/OMAP) ...has at least toggle update problems
52 * - [23-feb-2009] minimal traffic scheduling to avoid bulk RX packet
53 * starvation ... nothing yet for TX, interrupt, or bulk.
55 * - Not tested with HNP, but some SRP paths seem to behave.
57 * NOTE 24-August-2006:
59 * - Bulk traffic finally uses both sides of hardware ep1, freeing up an
60 * extra endpoint for periodic use enabling hub + keybd + mouse. That
61 * mostly works, except that with "usbnet" it's easy to trigger cases
62 * with "ping" where RX loses. (a) ping to davinci, even "ping -f",
63 * fine; but (b) ping _from_ davinci, even "ping -c 1", ICMP RX loses
64 * although ARP RX wins. (That test was done with a full speed link.)
69 * NOTE on endpoint usage:
71 * CONTROL transfers all go through ep0. BULK ones go through dedicated IN
72 * and OUT endpoints ... hardware is dedicated for those "async" queue(s).
73 * (Yes, bulk _could_ use more of the endpoints than that, and would even
76 * INTERUPPT and ISOCHRONOUS transfers are scheduled to the other endpoints.
77 * So far that scheduling is both dumb and optimistic: the endpoint will be
78 * "claimed" until its software queue is no longer refilled. No multiplexing
79 * of transfers between endpoints, or anything clever.
83 static void musb_ep_program(struct musb *musb, u8 epnum,
84 struct urb *urb, int is_out,
85 u8 *buf, u32 offset, u32 len);
88 * Clear TX fifo. Needed to avoid BABBLE errors.
90 static void musb_h_tx_flush_fifo(struct musb_hw_ep *ep)
92 struct musb *musb = ep->musb;
93 void __iomem *epio = ep->regs;
98 csr = musb_readw(epio, MUSB_TXCSR);
99 while (csr & MUSB_TXCSR_FIFONOTEMPTY) {
101 dev_dbg(musb->controller, "Host TX FIFONOTEMPTY csr: %02x\n", csr);
103 csr |= MUSB_TXCSR_FLUSHFIFO;
104 musb_writew(epio, MUSB_TXCSR, csr);
105 csr = musb_readw(epio, MUSB_TXCSR);
106 if (WARN(retries-- < 1,
107 "Could not flush host TX%d fifo: csr: %04x\n",
114 static void musb_h_ep0_flush_fifo(struct musb_hw_ep *ep)
116 void __iomem *epio = ep->regs;
120 /* scrub any data left in the fifo */
122 csr = musb_readw(epio, MUSB_TXCSR);
123 if (!(csr & (MUSB_CSR0_TXPKTRDY | MUSB_CSR0_RXPKTRDY)))
125 musb_writew(epio, MUSB_TXCSR, MUSB_CSR0_FLUSHFIFO);
126 csr = musb_readw(epio, MUSB_TXCSR);
130 WARN(!retries, "Could not flush host TX%d fifo: csr: %04x\n",
133 /* and reset for the next transfer */
134 musb_writew(epio, MUSB_TXCSR, 0);
138 * Start transmit. Caller is responsible for locking shared resources.
139 * musb must be locked.
141 static inline void musb_h_tx_start(struct musb_hw_ep *ep)
145 /* NOTE: no locks here; caller should lock and select EP */
147 txcsr = musb_readw(ep->regs, MUSB_TXCSR);
148 txcsr |= MUSB_TXCSR_TXPKTRDY | MUSB_TXCSR_H_WZC_BITS;
149 musb_writew(ep->regs, MUSB_TXCSR, txcsr);
151 txcsr = MUSB_CSR0_H_SETUPPKT | MUSB_CSR0_TXPKTRDY;
152 musb_writew(ep->regs, MUSB_CSR0, txcsr);
157 static inline void musb_h_tx_dma_start(struct musb_hw_ep *ep)
161 /* NOTE: no locks here; caller should lock and select EP */
162 txcsr = musb_readw(ep->regs, MUSB_TXCSR);
163 txcsr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_H_WZC_BITS;
164 if (is_cppi_enabled())
165 txcsr |= MUSB_TXCSR_DMAMODE;
166 musb_writew(ep->regs, MUSB_TXCSR, txcsr);
169 static void musb_ep_set_qh(struct musb_hw_ep *ep, int is_in, struct musb_qh *qh)
171 if (is_in != 0 || ep->is_shared_fifo)
173 if (is_in == 0 || ep->is_shared_fifo)
177 static struct musb_qh *musb_ep_get_qh(struct musb_hw_ep *ep, int is_in)
179 return is_in ? ep->in_qh : ep->out_qh;
183 * Start the URB at the front of an endpoint's queue
184 * end must be claimed from the caller.
186 * Context: controller locked, irqs blocked
189 musb_start_urb(struct musb *musb, int is_in, struct musb_qh *qh)
193 void __iomem *mbase = musb->mregs;
194 struct urb *urb = next_urb(qh);
195 void *buf = urb->transfer_buffer;
197 struct musb_hw_ep *hw_ep = qh->hw_ep;
198 unsigned pipe = urb->pipe;
199 u8 address = usb_pipedevice(pipe);
200 int epnum = hw_ep->epnum;
202 /* initialize software qh state */
206 /* gather right source of data */
208 case USB_ENDPOINT_XFER_CONTROL:
209 /* control transfers always start with SETUP */
211 musb->ep0_stage = MUSB_EP0_START;
212 buf = urb->setup_packet;
216 case USB_ENDPOINT_XFER_ISOC:
219 offset = urb->iso_frame_desc[0].offset;
220 len = urb->iso_frame_desc[0].length;
223 default: /* bulk, interrupt */
224 /* actual_length may be nonzero on retry paths */
225 buf = urb->transfer_buffer + urb->actual_length;
226 len = urb->transfer_buffer_length - urb->actual_length;
229 dev_dbg(musb->controller, "qh %p urb %p dev%d ep%d%s%s, hw_ep %d, %p/%d\n",
230 qh, urb, address, qh->epnum,
231 is_in ? "in" : "out",
232 ({char *s; switch (qh->type) {
233 case USB_ENDPOINT_XFER_CONTROL: s = ""; break;
234 case USB_ENDPOINT_XFER_BULK: s = "-bulk"; break;
236 case USB_ENDPOINT_XFER_ISOC: s = "-iso"; break;
238 default: s = "-intr"; break;
240 epnum, buf + offset, len);
242 /* Configure endpoint */
243 musb_ep_set_qh(hw_ep, is_in, qh);
244 musb_ep_program(musb, epnum, urb, !is_in, buf, offset, len);
246 /* transmit may have more work: start it when it is time */
250 /* determine if the time is right for a periodic transfer */
253 case USB_ENDPOINT_XFER_ISOC:
255 case USB_ENDPOINT_XFER_INT:
256 dev_dbg(musb->controller, "check whether there's still time for periodic Tx\n");
257 frame = musb_readw(mbase, MUSB_FRAME);
258 /* FIXME this doesn't implement that scheduling policy ...
259 * or handle framecounter wrapping
262 if ((urb->transfer_flags & URB_ISO_ASAP)
263 || (frame >= urb->start_frame)) {
264 /* REVISIT the SOF irq handler shouldn't duplicate
265 * this code; and we don't init urb->start_frame...
271 qh->frame = urb->start_frame;
272 /* enable SOF interrupt so we can count down */
273 dev_dbg(musb->controller, "SOF for %d\n", epnum);
274 #if 1 /* ifndef CONFIG_ARCH_DAVINCI */
275 musb_writeb(mbase, MUSB_INTRUSBE, 0xff);
283 dev_dbg(musb->controller, "Start TX%d %s\n", epnum,
284 hw_ep->tx_channel ? "dma" : "pio");
286 if (!hw_ep->tx_channel)
287 musb_h_tx_start(hw_ep);
288 else if (is_cppi_enabled() || tusb_dma_omap())
289 musb_h_tx_dma_start(hw_ep);
293 /* Context: caller owns controller lock, IRQs are blocked */
294 static void musb_giveback(struct musb *musb, struct urb *urb, int status)
295 __releases(musb->lock)
296 __acquires(musb->lock)
298 dev_dbg(musb->controller,
299 "complete %p %pF (%d), dev%d ep%d%s, %d/%d\n",
300 urb, urb->complete, status,
301 usb_pipedevice(urb->pipe),
302 usb_pipeendpoint(urb->pipe),
303 usb_pipein(urb->pipe) ? "in" : "out",
304 urb->actual_length, urb->transfer_buffer_length
307 usb_hcd_unlink_urb_from_ep(musb_to_hcd(musb), urb);
308 spin_unlock(&musb->lock);
309 usb_hcd_giveback_urb(musb_to_hcd(musb), urb, status);
310 spin_lock(&musb->lock);
313 /* For bulk/interrupt endpoints only */
314 static inline void musb_save_toggle(struct musb_qh *qh, int is_in,
317 void __iomem *epio = qh->hw_ep->regs;
321 * FIXME: the current Mentor DMA code seems to have
322 * problems getting toggle correct.
326 csr = musb_readw(epio, MUSB_RXCSR) & MUSB_RXCSR_H_DATATOGGLE;
328 csr = musb_readw(epio, MUSB_TXCSR) & MUSB_TXCSR_H_DATATOGGLE;
330 usb_settoggle(urb->dev, qh->epnum, !is_in, csr ? 1 : 0);
334 * Advance this hardware endpoint's queue, completing the specified URB and
335 * advancing to either the next URB queued to that qh, or else invalidating
336 * that qh and advancing to the next qh scheduled after the current one.
338 * Context: caller owns controller lock, IRQs are blocked
340 static void musb_advance_schedule(struct musb *musb, struct urb *urb,
341 struct musb_hw_ep *hw_ep, int is_in)
343 struct musb_qh *qh = musb_ep_get_qh(hw_ep, is_in);
344 struct musb_hw_ep *ep = qh->hw_ep;
345 int ready = qh->is_ready;
348 status = (urb->status == -EINPROGRESS) ? 0 : urb->status;
350 /* save toggle eagerly, for paranoia */
352 case USB_ENDPOINT_XFER_BULK:
353 case USB_ENDPOINT_XFER_INT:
354 musb_save_toggle(qh, is_in, urb);
357 case USB_ENDPOINT_XFER_ISOC:
358 if (status == 0 && urb->error_count)
365 musb_giveback(musb, urb, status);
366 qh->is_ready = ready;
368 /* reclaim resources (and bandwidth) ASAP; deschedule it, and
369 * invalidate qh as soon as list_empty(&hep->urb_list)
371 if (list_empty(&qh->hep->urb_list)) {
372 struct list_head *head;
373 struct dma_controller *dma = musb->dma_controller;
377 if (ep->rx_channel) {
378 dma->channel_release(ep->rx_channel);
379 ep->rx_channel = NULL;
383 if (ep->tx_channel) {
384 dma->channel_release(ep->tx_channel);
385 ep->tx_channel = NULL;
389 /* Clobber old pointers to this qh */
390 musb_ep_set_qh(ep, is_in, NULL);
391 qh->hep->hcpriv = NULL;
395 case USB_ENDPOINT_XFER_CONTROL:
396 case USB_ENDPOINT_XFER_BULK:
397 /* fifo policy for these lists, except that NAKing
398 * should rotate a qh to the end (for fairness).
401 head = qh->ring.prev;
408 case USB_ENDPOINT_XFER_ISOC:
409 case USB_ENDPOINT_XFER_INT:
410 /* this is where periodic bandwidth should be
411 * de-allocated if it's tracked and allocated;
412 * and where we'd update the schedule tree...
420 if (qh != NULL && qh->is_ready) {
421 dev_dbg(musb->controller, "... next ep%d %cX urb %p\n",
422 hw_ep->epnum, is_in ? 'R' : 'T', next_urb(qh));
423 musb_start_urb(musb, is_in, qh);
427 static u16 musb_h_flush_rxfifo(struct musb_hw_ep *hw_ep, u16 csr)
429 /* we don't want fifo to fill itself again;
430 * ignore dma (various models),
431 * leave toggle alone (may not have been saved yet)
433 csr |= MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_RXPKTRDY;
434 csr &= ~(MUSB_RXCSR_H_REQPKT
435 | MUSB_RXCSR_H_AUTOREQ
436 | MUSB_RXCSR_AUTOCLEAR);
438 /* write 2x to allow double buffering */
439 musb_writew(hw_ep->regs, MUSB_RXCSR, csr);
440 musb_writew(hw_ep->regs, MUSB_RXCSR, csr);
442 /* flush writebuffer */
443 return musb_readw(hw_ep->regs, MUSB_RXCSR);
447 * PIO RX for a packet (or part of it).
450 musb_host_packet_rx(struct musb *musb, struct urb *urb, u8 epnum, u8 iso_err)
458 struct musb_hw_ep *hw_ep = musb->endpoints + epnum;
459 void __iomem *epio = hw_ep->regs;
460 struct musb_qh *qh = hw_ep->in_qh;
461 int pipe = urb->pipe;
462 void *buffer = urb->transfer_buffer;
464 /* musb_ep_select(mbase, epnum); */
465 rx_count = musb_readw(epio, MUSB_RXCOUNT);
466 dev_dbg(musb->controller, "RX%d count %d, buffer %p len %d/%d\n", epnum, rx_count,
467 urb->transfer_buffer, qh->offset,
468 urb->transfer_buffer_length);
472 if (usb_pipeisoc(pipe)) {
474 struct usb_iso_packet_descriptor *d;
481 d = urb->iso_frame_desc + qh->iso_idx;
482 buf = buffer + d->offset;
484 if (rx_count > length) {
489 dev_dbg(musb->controller, "** OVERFLOW %d into %d\n", rx_count, length);
493 urb->actual_length += length;
494 d->actual_length = length;
498 /* see if we are done */
499 done = (++qh->iso_idx >= urb->number_of_packets);
503 buf = buffer + qh->offset;
504 length = urb->transfer_buffer_length - qh->offset;
505 if (rx_count > length) {
506 if (urb->status == -EINPROGRESS)
507 urb->status = -EOVERFLOW;
508 dev_dbg(musb->controller, "** OVERFLOW %d into %d\n", rx_count, length);
512 urb->actual_length += length;
513 qh->offset += length;
515 /* see if we are done */
516 done = (urb->actual_length == urb->transfer_buffer_length)
517 || (rx_count < qh->maxpacket)
518 || (urb->status != -EINPROGRESS);
520 && (urb->status == -EINPROGRESS)
521 && (urb->transfer_flags & URB_SHORT_NOT_OK)
522 && (urb->actual_length
523 < urb->transfer_buffer_length))
524 urb->status = -EREMOTEIO;
529 musb_read_fifo(hw_ep, length, buf);
531 csr = musb_readw(epio, MUSB_RXCSR);
532 csr |= MUSB_RXCSR_H_WZC_BITS;
533 if (unlikely(do_flush))
534 musb_h_flush_rxfifo(hw_ep, csr);
536 /* REVISIT this assumes AUTOCLEAR is never set */
537 csr &= ~(MUSB_RXCSR_RXPKTRDY | MUSB_RXCSR_H_REQPKT);
539 csr |= MUSB_RXCSR_H_REQPKT;
540 musb_writew(epio, MUSB_RXCSR, csr);
546 /* we don't always need to reinit a given side of an endpoint...
547 * when we do, use tx/rx reinit routine and then construct a new CSR
548 * to address data toggle, NYET, and DMA or PIO.
550 * it's possible that driver bugs (especially for DMA) or aborting a
551 * transfer might have left the endpoint busier than it should be.
552 * the busy/not-empty tests are basically paranoia.
555 musb_rx_reinit(struct musb *musb, struct musb_qh *qh, struct musb_hw_ep *ep)
559 /* NOTE: we know the "rx" fifo reinit never triggers for ep0.
560 * That always uses tx_reinit since ep0 repurposes TX register
561 * offsets; the initial SETUP packet is also a kind of OUT.
564 /* if programmed for Tx, put it in RX mode */
565 if (ep->is_shared_fifo) {
566 csr = musb_readw(ep->regs, MUSB_TXCSR);
567 if (csr & MUSB_TXCSR_MODE) {
568 musb_h_tx_flush_fifo(ep);
569 csr = musb_readw(ep->regs, MUSB_TXCSR);
570 musb_writew(ep->regs, MUSB_TXCSR,
571 csr | MUSB_TXCSR_FRCDATATOG);
575 * Clear the MODE bit (and everything else) to enable Rx.
576 * NOTE: we mustn't clear the DMAMODE bit before DMAENAB.
578 if (csr & MUSB_TXCSR_DMAMODE)
579 musb_writew(ep->regs, MUSB_TXCSR, MUSB_TXCSR_DMAMODE);
580 musb_writew(ep->regs, MUSB_TXCSR, 0);
582 /* scrub all previous state, clearing toggle */
584 csr = musb_readw(ep->regs, MUSB_RXCSR);
585 if (csr & MUSB_RXCSR_RXPKTRDY)
586 WARNING("rx%d, packet/%d ready?\n", ep->epnum,
587 musb_readw(ep->regs, MUSB_RXCOUNT));
589 musb_h_flush_rxfifo(ep, MUSB_RXCSR_CLRDATATOG);
592 /* target addr and (for multipoint) hub addr/port */
593 if (musb->is_multipoint) {
594 musb_write_rxfunaddr(ep->target_regs, qh->addr_reg);
595 musb_write_rxhubaddr(ep->target_regs, qh->h_addr_reg);
596 musb_write_rxhubport(ep->target_regs, qh->h_port_reg);
599 musb_writeb(musb->mregs, MUSB_FADDR, qh->addr_reg);
601 /* protocol/endpoint, interval/NAKlimit, i/o size */
602 musb_writeb(ep->regs, MUSB_RXTYPE, qh->type_reg);
603 musb_writeb(ep->regs, MUSB_RXINTERVAL, qh->intv_reg);
604 /* NOTE: bulk combining rewrites high bits of maxpacket */
605 /* Set RXMAXP with the FIFO size of the endpoint
606 * to disable double buffer mode.
608 if (musb->double_buffer_not_ok)
609 musb_writew(ep->regs, MUSB_RXMAXP, ep->max_packet_sz_rx);
611 musb_writew(ep->regs, MUSB_RXMAXP,
612 qh->maxpacket | ((qh->hb_mult - 1) << 11));
617 static bool musb_tx_dma_program(struct dma_controller *dma,
618 struct musb_hw_ep *hw_ep, struct musb_qh *qh,
619 struct urb *urb, u32 offset, u32 length)
621 struct dma_channel *channel = hw_ep->tx_channel;
622 void __iomem *epio = hw_ep->regs;
623 u16 pkt_size = qh->maxpacket;
627 #ifdef CONFIG_USB_INVENTRA_DMA
628 if (length > channel->max_len)
629 length = channel->max_len;
631 csr = musb_readw(epio, MUSB_TXCSR);
632 if (length > pkt_size) {
634 csr |= MUSB_TXCSR_DMAMODE | MUSB_TXCSR_DMAENAB;
635 /* autoset shouldn't be set in high bandwidth */
636 if (qh->hb_mult == 1)
637 csr |= MUSB_TXCSR_AUTOSET;
640 csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAMODE);
641 csr |= MUSB_TXCSR_DMAENAB; /* against programmer's guide */
643 channel->desired_mode = mode;
644 musb_writew(epio, MUSB_TXCSR, csr);
646 if (!is_cppi_enabled() && !tusb_dma_omap())
649 channel->actual_len = 0;
652 * TX uses "RNDIS" mode automatically but needs help
653 * to identify the zero-length-final-packet case.
655 mode = (urb->transfer_flags & URB_ZERO_PACKET) ? 1 : 0;
658 qh->segsize = length;
661 * Ensure the data reaches to main memory before starting
666 if (!dma->channel_program(channel, pkt_size, mode,
667 urb->transfer_dma + offset, length)) {
668 dma->channel_release(channel);
669 hw_ep->tx_channel = NULL;
671 csr = musb_readw(epio, MUSB_TXCSR);
672 csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAENAB);
673 musb_writew(epio, MUSB_TXCSR, csr | MUSB_TXCSR_H_WZC_BITS);
680 * Program an HDRC endpoint as per the given URB
681 * Context: irqs blocked, controller lock held
683 static void musb_ep_program(struct musb *musb, u8 epnum,
684 struct urb *urb, int is_out,
685 u8 *buf, u32 offset, u32 len)
687 struct dma_controller *dma_controller;
688 struct dma_channel *dma_channel;
690 void __iomem *mbase = musb->mregs;
691 struct musb_hw_ep *hw_ep = musb->endpoints + epnum;
692 void __iomem *epio = hw_ep->regs;
693 struct musb_qh *qh = musb_ep_get_qh(hw_ep, !is_out);
694 u16 packet_sz = qh->maxpacket;
696 dev_dbg(musb->controller, "%s hw%d urb %p spd%d dev%d ep%d%s "
697 "h_addr%02x h_port%02x bytes %d\n",
698 is_out ? "-->" : "<--",
699 epnum, urb, urb->dev->speed,
700 qh->addr_reg, qh->epnum, is_out ? "out" : "in",
701 qh->h_addr_reg, qh->h_port_reg,
704 musb_ep_select(mbase, epnum);
706 /* candidate for DMA? */
707 dma_controller = musb->dma_controller;
708 if (is_dma_capable() && epnum && dma_controller) {
709 dma_channel = is_out ? hw_ep->tx_channel : hw_ep->rx_channel;
711 dma_channel = dma_controller->channel_alloc(
712 dma_controller, hw_ep, is_out);
714 hw_ep->tx_channel = dma_channel;
716 hw_ep->rx_channel = dma_channel;
721 /* make sure we clear DMAEnab, autoSet bits from previous run */
723 /* OUT/transmit/EP0 or IN/receive? */
729 csr = musb_readw(epio, MUSB_TXCSR);
731 /* disable interrupt in case we flush */
732 int_txe = musb_readw(mbase, MUSB_INTRTXE);
733 musb_writew(mbase, MUSB_INTRTXE, int_txe & ~(1 << epnum));
735 /* general endpoint setup */
737 /* flush all old state, set default */
738 musb_h_tx_flush_fifo(hw_ep);
741 * We must not clear the DMAMODE bit before or in
742 * the same cycle with the DMAENAB bit, so we clear
743 * the latter first...
745 csr &= ~(MUSB_TXCSR_H_NAKTIMEOUT
748 | MUSB_TXCSR_FRCDATATOG
749 | MUSB_TXCSR_H_RXSTALL
751 | MUSB_TXCSR_TXPKTRDY
753 csr |= MUSB_TXCSR_MODE;
755 if (usb_gettoggle(urb->dev, qh->epnum, 1))
756 csr |= MUSB_TXCSR_H_WR_DATATOGGLE
757 | MUSB_TXCSR_H_DATATOGGLE;
759 csr |= MUSB_TXCSR_CLRDATATOG;
761 musb_writew(epio, MUSB_TXCSR, csr);
762 /* REVISIT may need to clear FLUSHFIFO ... */
763 csr &= ~MUSB_TXCSR_DMAMODE;
764 musb_writew(epio, MUSB_TXCSR, csr);
765 csr = musb_readw(epio, MUSB_TXCSR);
767 /* endpoint 0: just flush */
768 musb_h_ep0_flush_fifo(hw_ep);
771 /* target addr and (for multipoint) hub addr/port */
772 if (musb->is_multipoint) {
773 musb_write_txfunaddr(mbase, epnum, qh->addr_reg);
774 musb_write_txhubaddr(mbase, epnum, qh->h_addr_reg);
775 musb_write_txhubport(mbase, epnum, qh->h_port_reg);
776 /* FIXME if !epnum, do the same for RX ... */
778 musb_writeb(mbase, MUSB_FADDR, qh->addr_reg);
780 /* protocol/endpoint/interval/NAKlimit */
782 musb_writeb(epio, MUSB_TXTYPE, qh->type_reg);
783 if (musb->double_buffer_not_ok)
784 musb_writew(epio, MUSB_TXMAXP,
785 hw_ep->max_packet_sz_tx);
786 else if (can_bulk_split(musb, qh->type))
787 musb_writew(epio, MUSB_TXMAXP, packet_sz
788 | ((hw_ep->max_packet_sz_tx /
789 packet_sz) - 1) << 11);
791 musb_writew(epio, MUSB_TXMAXP,
793 ((qh->hb_mult - 1) << 11));
794 musb_writeb(epio, MUSB_TXINTERVAL, qh->intv_reg);
796 musb_writeb(epio, MUSB_NAKLIMIT0, qh->intv_reg);
797 if (musb->is_multipoint)
798 musb_writeb(epio, MUSB_TYPE0,
802 if (can_bulk_split(musb, qh->type))
803 load_count = min((u32) hw_ep->max_packet_sz_tx,
806 load_count = min((u32) packet_sz, len);
808 if (dma_channel && musb_tx_dma_program(dma_controller,
809 hw_ep, qh, urb, offset, len))
813 /* PIO to load FIFO */
814 qh->segsize = load_count;
815 musb_write_fifo(hw_ep, load_count, buf);
818 /* re-enable interrupt */
819 musb_writew(mbase, MUSB_INTRTXE, int_txe);
825 if (hw_ep->rx_reinit) {
826 musb_rx_reinit(musb, qh, hw_ep);
828 /* init new state: toggle and NYET, maybe DMA later */
829 if (usb_gettoggle(urb->dev, qh->epnum, 0))
830 csr = MUSB_RXCSR_H_WR_DATATOGGLE
831 | MUSB_RXCSR_H_DATATOGGLE;
834 if (qh->type == USB_ENDPOINT_XFER_INT)
835 csr |= MUSB_RXCSR_DISNYET;
838 csr = musb_readw(hw_ep->regs, MUSB_RXCSR);
840 if (csr & (MUSB_RXCSR_RXPKTRDY
842 | MUSB_RXCSR_H_REQPKT))
843 ERR("broken !rx_reinit, ep%d csr %04x\n",
846 /* scrub any stale state, leaving toggle alone */
847 csr &= MUSB_RXCSR_DISNYET;
850 /* kick things off */
852 if ((is_cppi_enabled() || tusb_dma_omap()) && dma_channel) {
853 /* Candidate for DMA */
854 dma_channel->actual_len = 0L;
857 /* AUTOREQ is in a DMA register */
858 musb_writew(hw_ep->regs, MUSB_RXCSR, csr);
859 csr = musb_readw(hw_ep->regs, MUSB_RXCSR);
862 * Unless caller treats short RX transfers as
863 * errors, we dare not queue multiple transfers.
865 dma_ok = dma_controller->channel_program(dma_channel,
866 packet_sz, !(urb->transfer_flags &
868 urb->transfer_dma + offset,
871 dma_controller->channel_release(dma_channel);
872 hw_ep->rx_channel = dma_channel = NULL;
874 csr |= MUSB_RXCSR_DMAENAB;
877 csr |= MUSB_RXCSR_H_REQPKT;
878 dev_dbg(musb->controller, "RXCSR%d := %04x\n", epnum, csr);
879 musb_writew(hw_ep->regs, MUSB_RXCSR, csr);
880 csr = musb_readw(hw_ep->regs, MUSB_RXCSR);
886 * Service the default endpoint (ep0) as host.
887 * Return true until it's time to start the status stage.
889 static bool musb_h_ep0_continue(struct musb *musb, u16 len, struct urb *urb)
892 u8 *fifo_dest = NULL;
894 struct musb_hw_ep *hw_ep = musb->control_ep;
895 struct musb_qh *qh = hw_ep->in_qh;
896 struct usb_ctrlrequest *request;
898 switch (musb->ep0_stage) {
900 fifo_dest = urb->transfer_buffer + urb->actual_length;
901 fifo_count = min_t(size_t, len, urb->transfer_buffer_length -
903 if (fifo_count < len)
904 urb->status = -EOVERFLOW;
906 musb_read_fifo(hw_ep, fifo_count, fifo_dest);
908 urb->actual_length += fifo_count;
909 if (len < qh->maxpacket) {
910 /* always terminate on short read; it's
911 * rarely reported as an error.
913 } else if (urb->actual_length <
914 urb->transfer_buffer_length)
918 request = (struct usb_ctrlrequest *) urb->setup_packet;
920 if (!request->wLength) {
921 dev_dbg(musb->controller, "start no-DATA\n");
923 } else if (request->bRequestType & USB_DIR_IN) {
924 dev_dbg(musb->controller, "start IN-DATA\n");
925 musb->ep0_stage = MUSB_EP0_IN;
929 dev_dbg(musb->controller, "start OUT-DATA\n");
930 musb->ep0_stage = MUSB_EP0_OUT;
935 fifo_count = min_t(size_t, qh->maxpacket,
936 urb->transfer_buffer_length -
939 fifo_dest = (u8 *) (urb->transfer_buffer
940 + urb->actual_length);
941 dev_dbg(musb->controller, "Sending %d byte%s to ep0 fifo %p\n",
943 (fifo_count == 1) ? "" : "s",
945 musb_write_fifo(hw_ep, fifo_count, fifo_dest);
947 urb->actual_length += fifo_count;
952 ERR("bogus ep0 stage %d\n", musb->ep0_stage);
960 * Handle default endpoint interrupt as host. Only called in IRQ time
961 * from musb_interrupt().
963 * called with controller irqlocked
965 irqreturn_t musb_h_ep0_irq(struct musb *musb)
970 void __iomem *mbase = musb->mregs;
971 struct musb_hw_ep *hw_ep = musb->control_ep;
972 void __iomem *epio = hw_ep->regs;
973 struct musb_qh *qh = hw_ep->in_qh;
974 bool complete = false;
975 irqreturn_t retval = IRQ_NONE;
977 /* ep0 only has one queue, "in" */
980 musb_ep_select(mbase, 0);
981 csr = musb_readw(epio, MUSB_CSR0);
982 len = (csr & MUSB_CSR0_RXPKTRDY)
983 ? musb_readb(epio, MUSB_COUNT0)
986 dev_dbg(musb->controller, "<== csr0 %04x, qh %p, count %d, urb %p, stage %d\n",
987 csr, qh, len, urb, musb->ep0_stage);
989 /* if we just did status stage, we are done */
990 if (MUSB_EP0_STATUS == musb->ep0_stage) {
991 retval = IRQ_HANDLED;
996 if (csr & MUSB_CSR0_H_RXSTALL) {
997 dev_dbg(musb->controller, "STALLING ENDPOINT\n");
1000 } else if (csr & MUSB_CSR0_H_ERROR) {
1001 dev_dbg(musb->controller, "no response, csr0 %04x\n", csr);
1004 } else if (csr & MUSB_CSR0_H_NAKTIMEOUT) {
1005 dev_dbg(musb->controller, "control NAK timeout\n");
1007 /* NOTE: this code path would be a good place to PAUSE a
1008 * control transfer, if another one is queued, so that
1009 * ep0 is more likely to stay busy. That's already done
1010 * for bulk RX transfers.
1012 * if (qh->ring.next != &musb->control), then
1013 * we have a candidate... NAKing is *NOT* an error
1015 musb_writew(epio, MUSB_CSR0, 0);
1016 retval = IRQ_HANDLED;
1020 dev_dbg(musb->controller, "aborting\n");
1021 retval = IRQ_HANDLED;
1023 urb->status = status;
1026 /* use the proper sequence to abort the transfer */
1027 if (csr & MUSB_CSR0_H_REQPKT) {
1028 csr &= ~MUSB_CSR0_H_REQPKT;
1029 musb_writew(epio, MUSB_CSR0, csr);
1030 csr &= ~MUSB_CSR0_H_NAKTIMEOUT;
1031 musb_writew(epio, MUSB_CSR0, csr);
1033 musb_h_ep0_flush_fifo(hw_ep);
1036 musb_writeb(epio, MUSB_NAKLIMIT0, 0);
1039 musb_writew(epio, MUSB_CSR0, 0);
1042 if (unlikely(!urb)) {
1043 /* stop endpoint since we have no place for its data, this
1044 * SHOULD NEVER HAPPEN! */
1045 ERR("no URB for end 0\n");
1047 musb_h_ep0_flush_fifo(hw_ep);
1052 /* call common logic and prepare response */
1053 if (musb_h_ep0_continue(musb, len, urb)) {
1054 /* more packets required */
1055 csr = (MUSB_EP0_IN == musb->ep0_stage)
1056 ? MUSB_CSR0_H_REQPKT : MUSB_CSR0_TXPKTRDY;
1058 /* data transfer complete; perform status phase */
1059 if (usb_pipeout(urb->pipe)
1060 || !urb->transfer_buffer_length)
1061 csr = MUSB_CSR0_H_STATUSPKT
1062 | MUSB_CSR0_H_REQPKT;
1064 csr = MUSB_CSR0_H_STATUSPKT
1065 | MUSB_CSR0_TXPKTRDY;
1067 /* flag status stage */
1068 musb->ep0_stage = MUSB_EP0_STATUS;
1070 dev_dbg(musb->controller, "ep0 STATUS, csr %04x\n", csr);
1073 musb_writew(epio, MUSB_CSR0, csr);
1074 retval = IRQ_HANDLED;
1076 musb->ep0_stage = MUSB_EP0_IDLE;
1078 /* call completion handler if done */
1080 musb_advance_schedule(musb, urb, hw_ep, 1);
1086 #ifdef CONFIG_USB_INVENTRA_DMA
1088 /* Host side TX (OUT) using Mentor DMA works as follows:
1090 - if queue was empty, Program Endpoint
1091 - ... which starts DMA to fifo in mode 1 or 0
1093 DMA Isr (transfer complete) -> TxAvail()
1094 - Stop DMA (~DmaEnab) (<--- Alert ... currently happens
1095 only in musb_cleanup_urb)
1096 - TxPktRdy has to be set in mode 0 or for
1097 short packets in mode 1.
1102 /* Service a Tx-Available or dma completion irq for the endpoint */
1103 void musb_host_tx(struct musb *musb, u8 epnum)
1110 struct musb_hw_ep *hw_ep = musb->endpoints + epnum;
1111 void __iomem *epio = hw_ep->regs;
1112 struct musb_qh *qh = hw_ep->out_qh;
1113 struct urb *urb = next_urb(qh);
1115 void __iomem *mbase = musb->mregs;
1116 struct dma_channel *dma;
1117 bool transfer_pending = false;
1119 musb_ep_select(mbase, epnum);
1120 tx_csr = musb_readw(epio, MUSB_TXCSR);
1122 /* with CPPI, DMA sometimes triggers "extra" irqs */
1124 dev_dbg(musb->controller, "extra TX%d ready, csr %04x\n", epnum, tx_csr);
1129 dma = is_dma_capable() ? hw_ep->tx_channel : NULL;
1130 dev_dbg(musb->controller, "OUT/TX%d end, csr %04x%s\n", epnum, tx_csr,
1131 dma ? ", dma" : "");
1133 /* check for errors */
1134 if (tx_csr & MUSB_TXCSR_H_RXSTALL) {
1135 /* dma was disabled, fifo flushed */
1136 dev_dbg(musb->controller, "TX end %d stall\n", epnum);
1138 /* stall; record URB status */
1141 } else if (tx_csr & MUSB_TXCSR_H_ERROR) {
1142 /* (NON-ISO) dma was disabled, fifo flushed */
1143 dev_dbg(musb->controller, "TX 3strikes on ep=%d\n", epnum);
1145 status = -ETIMEDOUT;
1147 } else if (tx_csr & MUSB_TXCSR_H_NAKTIMEOUT) {
1148 dev_dbg(musb->controller, "TX end=%d device not responding\n", epnum);
1150 /* NOTE: this code path would be a good place to PAUSE a
1151 * transfer, if there's some other (nonperiodic) tx urb
1152 * that could use this fifo. (dma complicates it...)
1153 * That's already done for bulk RX transfers.
1155 * if (bulk && qh->ring.next != &musb->out_bulk), then
1156 * we have a candidate... NAKing is *NOT* an error
1158 musb_ep_select(mbase, epnum);
1159 musb_writew(epio, MUSB_TXCSR,
1160 MUSB_TXCSR_H_WZC_BITS
1161 | MUSB_TXCSR_TXPKTRDY);
1166 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) {
1167 dma->status = MUSB_DMA_STATUS_CORE_ABORT;
1168 (void) musb->dma_controller->channel_abort(dma);
1171 /* do the proper sequence to abort the transfer in the
1172 * usb core; the dma engine should already be stopped.
1174 musb_h_tx_flush_fifo(hw_ep);
1175 tx_csr &= ~(MUSB_TXCSR_AUTOSET
1176 | MUSB_TXCSR_DMAENAB
1177 | MUSB_TXCSR_H_ERROR
1178 | MUSB_TXCSR_H_RXSTALL
1179 | MUSB_TXCSR_H_NAKTIMEOUT
1182 musb_ep_select(mbase, epnum);
1183 musb_writew(epio, MUSB_TXCSR, tx_csr);
1184 /* REVISIT may need to clear FLUSHFIFO ... */
1185 musb_writew(epio, MUSB_TXCSR, tx_csr);
1186 musb_writeb(epio, MUSB_TXINTERVAL, 0);
1191 /* second cppi case */
1192 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) {
1193 dev_dbg(musb->controller, "extra TX%d ready, csr %04x\n", epnum, tx_csr);
1197 if (is_dma_capable() && dma && !status) {
1199 * DMA has completed. But if we're using DMA mode 1 (multi
1200 * packet DMA), we need a terminal TXPKTRDY interrupt before
1201 * we can consider this transfer completed, lest we trash
1202 * its last packet when writing the next URB's data. So we
1203 * switch back to mode 0 to get that interrupt; we'll come
1204 * back here once it happens.
1206 if (tx_csr & MUSB_TXCSR_DMAMODE) {
1208 * We shouldn't clear DMAMODE with DMAENAB set; so
1209 * clear them in a safe order. That should be OK
1210 * once TXPKTRDY has been set (and I've never seen
1211 * it being 0 at this moment -- DMA interrupt latency
1212 * is significant) but if it hasn't been then we have
1213 * no choice but to stop being polite and ignore the
1214 * programmer's guide... :-)
1216 * Note that we must write TXCSR with TXPKTRDY cleared
1217 * in order not to re-trigger the packet send (this bit
1218 * can't be cleared by CPU), and there's another caveat:
1219 * TXPKTRDY may be set shortly and then cleared in the
1220 * double-buffered FIFO mode, so we do an extra TXCSR
1221 * read for debouncing...
1223 tx_csr &= musb_readw(epio, MUSB_TXCSR);
1224 if (tx_csr & MUSB_TXCSR_TXPKTRDY) {
1225 tx_csr &= ~(MUSB_TXCSR_DMAENAB |
1226 MUSB_TXCSR_TXPKTRDY);
1227 musb_writew(epio, MUSB_TXCSR,
1228 tx_csr | MUSB_TXCSR_H_WZC_BITS);
1230 tx_csr &= ~(MUSB_TXCSR_DMAMODE |
1231 MUSB_TXCSR_TXPKTRDY);
1232 musb_writew(epio, MUSB_TXCSR,
1233 tx_csr | MUSB_TXCSR_H_WZC_BITS);
1236 * There is no guarantee that we'll get an interrupt
1237 * after clearing DMAMODE as we might have done this
1238 * too late (after TXPKTRDY was cleared by controller).
1239 * Re-read TXCSR as we have spoiled its previous value.
1241 tx_csr = musb_readw(epio, MUSB_TXCSR);
1245 * We may get here from a DMA completion or TXPKTRDY interrupt.
1246 * In any case, we must check the FIFO status here and bail out
1247 * only if the FIFO still has data -- that should prevent the
1248 * "missed" TXPKTRDY interrupts and deal with double-buffered
1251 if (tx_csr & (MUSB_TXCSR_FIFONOTEMPTY | MUSB_TXCSR_TXPKTRDY)) {
1252 dev_dbg(musb->controller, "DMA complete but packet still in FIFO, "
1253 "CSR %04x\n", tx_csr);
1258 if (!status || dma || usb_pipeisoc(pipe)) {
1260 length = dma->actual_len;
1262 length = qh->segsize;
1263 qh->offset += length;
1265 if (usb_pipeisoc(pipe)) {
1267 struct usb_iso_packet_descriptor *d;
1269 d = urb->iso_frame_desc + qh->iso_idx;
1270 d->actual_length = length;
1272 if (++qh->iso_idx >= urb->number_of_packets) {
1280 } else if (dma && urb->transfer_buffer_length == qh->offset) {
1283 /* see if we need to send more data, or ZLP */
1284 if (qh->segsize < qh->maxpacket)
1286 else if (qh->offset == urb->transfer_buffer_length
1287 && !(urb->transfer_flags
1291 offset = qh->offset;
1292 length = urb->transfer_buffer_length - offset;
1293 transfer_pending = true;
1298 /* urb->status != -EINPROGRESS means request has been faulted,
1299 * so we must abort this transfer after cleanup
1301 if (urb->status != -EINPROGRESS) {
1304 status = urb->status;
1309 urb->status = status;
1310 urb->actual_length = qh->offset;
1311 musb_advance_schedule(musb, urb, hw_ep, USB_DIR_OUT);
1313 } else if ((usb_pipeisoc(pipe) || transfer_pending) && dma) {
1314 if (musb_tx_dma_program(musb->dma_controller, hw_ep, qh, urb,
1316 if (is_cppi_enabled() || tusb_dma_omap())
1317 musb_h_tx_dma_start(hw_ep);
1320 } else if (tx_csr & MUSB_TXCSR_DMAENAB) {
1321 dev_dbg(musb->controller, "not complete, but DMA enabled?\n");
1326 * PIO: start next packet in this URB.
1328 * REVISIT: some docs say that when hw_ep->tx_double_buffered,
1329 * (and presumably, FIFO is not half-full) we should write *two*
1330 * packets before updating TXCSR; other docs disagree...
1332 if (length > qh->maxpacket)
1333 length = qh->maxpacket;
1334 /* Unmap the buffer so that CPU can use it */
1335 usb_hcd_unmap_urb_for_dma(musb_to_hcd(musb), urb);
1336 musb_write_fifo(hw_ep, length, urb->transfer_buffer + offset);
1337 qh->segsize = length;
1339 musb_ep_select(mbase, epnum);
1340 musb_writew(epio, MUSB_TXCSR,
1341 MUSB_TXCSR_H_WZC_BITS | MUSB_TXCSR_TXPKTRDY);
1345 #ifdef CONFIG_USB_INVENTRA_DMA
1347 /* Host side RX (IN) using Mentor DMA works as follows:
1349 - if queue was empty, ProgramEndpoint
1350 - first IN token is sent out (by setting ReqPkt)
1351 LinuxIsr -> RxReady()
1352 /\ => first packet is received
1353 | - Set in mode 0 (DmaEnab, ~ReqPkt)
1354 | -> DMA Isr (transfer complete) -> RxReady()
1355 | - Ack receive (~RxPktRdy), turn off DMA (~DmaEnab)
1356 | - if urb not complete, send next IN token (ReqPkt)
1357 | | else complete urb.
1359 ---------------------------
1361 * Nuances of mode 1:
1362 * For short packets, no ack (+RxPktRdy) is sent automatically
1363 * (even if AutoClear is ON)
1364 * For full packets, ack (~RxPktRdy) and next IN token (+ReqPkt) is sent
1365 * automatically => major problem, as collecting the next packet becomes
1366 * difficult. Hence mode 1 is not used.
1369 * All we care about at this driver level is that
1370 * (a) all URBs terminate with REQPKT cleared and fifo(s) empty;
1371 * (b) termination conditions are: short RX, or buffer full;
1372 * (c) fault modes include
1373 * - iff URB_SHORT_NOT_OK, short RX status is -EREMOTEIO.
1374 * (and that endpoint's dma queue stops immediately)
1375 * - overflow (full, PLUS more bytes in the terminal packet)
1377 * So for example, usb-storage sets URB_SHORT_NOT_OK, and would
1378 * thus be a great candidate for using mode 1 ... for all but the
1379 * last packet of one URB's transfer.
1384 /* Schedule next QH from musb->in_bulk and move the current qh to
1385 * the end; avoids starvation for other endpoints.
1387 static void musb_bulk_rx_nak_timeout(struct musb *musb, struct musb_hw_ep *ep)
1389 struct dma_channel *dma;
1391 void __iomem *mbase = musb->mregs;
1392 void __iomem *epio = ep->regs;
1393 struct musb_qh *cur_qh, *next_qh;
1396 musb_ep_select(mbase, ep->epnum);
1397 dma = is_dma_capable() ? ep->rx_channel : NULL;
1399 /* clear nak timeout bit */
1400 rx_csr = musb_readw(epio, MUSB_RXCSR);
1401 rx_csr |= MUSB_RXCSR_H_WZC_BITS;
1402 rx_csr &= ~MUSB_RXCSR_DATAERROR;
1403 musb_writew(epio, MUSB_RXCSR, rx_csr);
1405 cur_qh = first_qh(&musb->in_bulk);
1407 urb = next_urb(cur_qh);
1408 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) {
1409 dma->status = MUSB_DMA_STATUS_CORE_ABORT;
1410 musb->dma_controller->channel_abort(dma);
1411 urb->actual_length += dma->actual_len;
1412 dma->actual_len = 0L;
1414 musb_save_toggle(cur_qh, 1, urb);
1416 /* move cur_qh to end of queue */
1417 list_move_tail(&cur_qh->ring, &musb->in_bulk);
1419 /* get the next qh from musb->in_bulk */
1420 next_qh = first_qh(&musb->in_bulk);
1422 /* set rx_reinit and schedule the next qh */
1424 musb_start_urb(musb, 1, next_qh);
1429 * Service an RX interrupt for the given IN endpoint; docs cover bulk, iso,
1430 * and high-bandwidth IN transfer cases.
1432 void musb_host_rx(struct musb *musb, u8 epnum)
1435 struct musb_hw_ep *hw_ep = musb->endpoints + epnum;
1436 void __iomem *epio = hw_ep->regs;
1437 struct musb_qh *qh = hw_ep->in_qh;
1439 void __iomem *mbase = musb->mregs;
1442 bool iso_err = false;
1445 struct dma_channel *dma;
1447 musb_ep_select(mbase, epnum);
1450 dma = is_dma_capable() ? hw_ep->rx_channel : NULL;
1454 rx_csr = musb_readw(epio, MUSB_RXCSR);
1457 if (unlikely(!urb)) {
1458 /* REVISIT -- THIS SHOULD NEVER HAPPEN ... but, at least
1459 * usbtest #11 (unlinks) triggers it regularly, sometimes
1460 * with fifo full. (Only with DMA??)
1462 dev_dbg(musb->controller, "BOGUS RX%d ready, csr %04x, count %d\n", epnum, val,
1463 musb_readw(epio, MUSB_RXCOUNT));
1464 musb_h_flush_rxfifo(hw_ep, MUSB_RXCSR_CLRDATATOG);
1470 dev_dbg(musb->controller, "<== hw %d rxcsr %04x, urb actual %d (+dma %zu)\n",
1471 epnum, rx_csr, urb->actual_length,
1472 dma ? dma->actual_len : 0);
1474 /* check for errors, concurrent stall & unlink is not really
1476 if (rx_csr & MUSB_RXCSR_H_RXSTALL) {
1477 dev_dbg(musb->controller, "RX end %d STALL\n", epnum);
1479 /* stall; record URB status */
1482 } else if (rx_csr & MUSB_RXCSR_H_ERROR) {
1483 dev_dbg(musb->controller, "end %d RX proto error\n", epnum);
1486 musb_writeb(epio, MUSB_RXINTERVAL, 0);
1488 } else if (rx_csr & MUSB_RXCSR_DATAERROR) {
1490 if (USB_ENDPOINT_XFER_ISOC != qh->type) {
1491 dev_dbg(musb->controller, "RX end %d NAK timeout\n", epnum);
1493 /* NOTE: NAKing is *NOT* an error, so we want to
1494 * continue. Except ... if there's a request for
1495 * another QH, use that instead of starving it.
1497 * Devices like Ethernet and serial adapters keep
1498 * reads posted at all times, which will starve
1499 * other devices without this logic.
1501 if (usb_pipebulk(urb->pipe)
1503 && !list_is_singular(&musb->in_bulk)) {
1504 musb_bulk_rx_nak_timeout(musb, hw_ep);
1507 musb_ep_select(mbase, epnum);
1508 rx_csr |= MUSB_RXCSR_H_WZC_BITS;
1509 rx_csr &= ~MUSB_RXCSR_DATAERROR;
1510 musb_writew(epio, MUSB_RXCSR, rx_csr);
1514 dev_dbg(musb->controller, "RX end %d ISO data error\n", epnum);
1515 /* packet error reported later */
1518 } else if (rx_csr & MUSB_RXCSR_INCOMPRX) {
1519 dev_dbg(musb->controller, "end %d high bandwidth incomplete ISO packet RX\n",
1524 /* faults abort the transfer */
1526 /* clean up dma and collect transfer count */
1527 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) {
1528 dma->status = MUSB_DMA_STATUS_CORE_ABORT;
1529 (void) musb->dma_controller->channel_abort(dma);
1530 xfer_len = dma->actual_len;
1532 musb_h_flush_rxfifo(hw_ep, MUSB_RXCSR_CLRDATATOG);
1533 musb_writeb(epio, MUSB_RXINTERVAL, 0);
1538 if (unlikely(dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY)) {
1539 /* SHOULD NEVER HAPPEN ... but at least DaVinci has done it */
1540 ERR("RX%d dma busy, csr %04x\n", epnum, rx_csr);
1544 /* thorough shutdown for now ... given more precise fault handling
1545 * and better queueing support, we might keep a DMA pipeline going
1546 * while processing this irq for earlier completions.
1549 /* FIXME this is _way_ too much in-line logic for Mentor DMA */
1551 #ifndef CONFIG_USB_INVENTRA_DMA
1552 if (rx_csr & MUSB_RXCSR_H_REQPKT) {
1553 /* REVISIT this happened for a while on some short reads...
1554 * the cleanup still needs investigation... looks bad...
1555 * and also duplicates dma cleanup code above ... plus,
1556 * shouldn't this be the "half full" double buffer case?
1558 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) {
1559 dma->status = MUSB_DMA_STATUS_CORE_ABORT;
1560 (void) musb->dma_controller->channel_abort(dma);
1561 xfer_len = dma->actual_len;
1565 dev_dbg(musb->controller, "RXCSR%d %04x, reqpkt, len %zu%s\n", epnum, rx_csr,
1566 xfer_len, dma ? ", dma" : "");
1567 rx_csr &= ~MUSB_RXCSR_H_REQPKT;
1569 musb_ep_select(mbase, epnum);
1570 musb_writew(epio, MUSB_RXCSR,
1571 MUSB_RXCSR_H_WZC_BITS | rx_csr);
1574 if (dma && (rx_csr & MUSB_RXCSR_DMAENAB)) {
1575 xfer_len = dma->actual_len;
1577 val &= ~(MUSB_RXCSR_DMAENAB
1578 | MUSB_RXCSR_H_AUTOREQ
1579 | MUSB_RXCSR_AUTOCLEAR
1580 | MUSB_RXCSR_RXPKTRDY);
1581 musb_writew(hw_ep->regs, MUSB_RXCSR, val);
1583 #ifdef CONFIG_USB_INVENTRA_DMA
1584 if (usb_pipeisoc(pipe)) {
1585 struct usb_iso_packet_descriptor *d;
1587 d = urb->iso_frame_desc + qh->iso_idx;
1588 d->actual_length = xfer_len;
1590 /* even if there was an error, we did the dma
1591 * for iso_frame_desc->length
1593 if (d->status != -EILSEQ && d->status != -EOVERFLOW)
1596 if (++qh->iso_idx >= urb->number_of_packets)
1602 /* done if urb buffer is full or short packet is recd */
1603 done = (urb->actual_length + xfer_len >=
1604 urb->transfer_buffer_length
1605 || dma->actual_len < qh->maxpacket);
1608 /* send IN token for next packet, without AUTOREQ */
1610 val |= MUSB_RXCSR_H_REQPKT;
1611 musb_writew(epio, MUSB_RXCSR,
1612 MUSB_RXCSR_H_WZC_BITS | val);
1615 dev_dbg(musb->controller, "ep %d dma %s, rxcsr %04x, rxcount %d\n", epnum,
1616 done ? "off" : "reset",
1617 musb_readw(epio, MUSB_RXCSR),
1618 musb_readw(epio, MUSB_RXCOUNT));
1622 } else if (urb->status == -EINPROGRESS) {
1623 /* if no errors, be sure a packet is ready for unloading */
1624 if (unlikely(!(rx_csr & MUSB_RXCSR_RXPKTRDY))) {
1626 ERR("Rx interrupt with no errors or packet!\n");
1628 /* FIXME this is another "SHOULD NEVER HAPPEN" */
1631 /* do the proper sequence to abort the transfer */
1632 musb_ep_select(mbase, epnum);
1633 val &= ~MUSB_RXCSR_H_REQPKT;
1634 musb_writew(epio, MUSB_RXCSR, val);
1638 /* we are expecting IN packets */
1639 #ifdef CONFIG_USB_INVENTRA_DMA
1641 struct dma_controller *c;
1646 rx_count = musb_readw(epio, MUSB_RXCOUNT);
1648 dev_dbg(musb->controller, "RX%d count %d, buffer 0x%x len %d/%d\n",
1651 + urb->actual_length,
1653 urb->transfer_buffer_length);
1655 c = musb->dma_controller;
1657 if (usb_pipeisoc(pipe)) {
1659 struct usb_iso_packet_descriptor *d;
1661 d = urb->iso_frame_desc + qh->iso_idx;
1667 if (rx_count > d->length) {
1668 if (d_status == 0) {
1669 d_status = -EOVERFLOW;
1672 dev_dbg(musb->controller, "** OVERFLOW %d into %d\n",\
1673 rx_count, d->length);
1678 d->status = d_status;
1679 buf = urb->transfer_dma + d->offset;
1682 buf = urb->transfer_dma +
1686 dma->desired_mode = 0;
1688 /* because of the issue below, mode 1 will
1689 * only rarely behave with correct semantics.
1691 if ((urb->transfer_flags &
1693 && (urb->transfer_buffer_length -
1696 dma->desired_mode = 1;
1697 if (rx_count < hw_ep->max_packet_sz_rx) {
1699 dma->desired_mode = 0;
1701 length = urb->transfer_buffer_length;
1705 /* Disadvantage of using mode 1:
1706 * It's basically usable only for mass storage class; essentially all
1707 * other protocols also terminate transfers on short packets.
1710 * An extra IN token is sent at the end of the transfer (due to AUTOREQ)
1711 * If you try to use mode 1 for (transfer_buffer_length - 512), and try
1712 * to use the extra IN token to grab the last packet using mode 0, then
1713 * the problem is that you cannot be sure when the device will send the
1714 * last packet and RxPktRdy set. Sometimes the packet is recd too soon
1715 * such that it gets lost when RxCSR is re-set at the end of the mode 1
1716 * transfer, while sometimes it is recd just a little late so that if you
1717 * try to configure for mode 0 soon after the mode 1 transfer is
1718 * completed, you will find rxcount 0. Okay, so you might think why not
1719 * wait for an interrupt when the pkt is recd. Well, you won't get any!
1722 val = musb_readw(epio, MUSB_RXCSR);
1723 val &= ~MUSB_RXCSR_H_REQPKT;
1725 if (dma->desired_mode == 0)
1726 val &= ~MUSB_RXCSR_H_AUTOREQ;
1728 val |= MUSB_RXCSR_H_AUTOREQ;
1729 val |= MUSB_RXCSR_DMAENAB;
1731 /* autoclear shouldn't be set in high bandwidth */
1732 if (qh->hb_mult == 1)
1733 val |= MUSB_RXCSR_AUTOCLEAR;
1735 musb_writew(epio, MUSB_RXCSR,
1736 MUSB_RXCSR_H_WZC_BITS | val);
1738 /* REVISIT if when actual_length != 0,
1739 * transfer_buffer_length needs to be
1742 ret = c->channel_program(
1744 dma->desired_mode, buf, length);
1747 c->channel_release(dma);
1748 hw_ep->rx_channel = NULL;
1750 val = musb_readw(epio, MUSB_RXCSR);
1751 val &= ~(MUSB_RXCSR_DMAENAB
1752 | MUSB_RXCSR_H_AUTOREQ
1753 | MUSB_RXCSR_AUTOCLEAR);
1754 musb_writew(epio, MUSB_RXCSR, val);
1757 #endif /* Mentor DMA */
1760 /* Unmap the buffer so that CPU can use it */
1761 usb_hcd_unmap_urb_for_dma(musb_to_hcd(musb), urb);
1762 done = musb_host_packet_rx(musb, urb,
1764 dev_dbg(musb->controller, "read %spacket\n", done ? "last " : "");
1769 urb->actual_length += xfer_len;
1770 qh->offset += xfer_len;
1772 if (urb->status == -EINPROGRESS)
1773 urb->status = status;
1774 musb_advance_schedule(musb, urb, hw_ep, USB_DIR_IN);
1778 /* schedule nodes correspond to peripheral endpoints, like an OHCI QH.
1779 * the software schedule associates multiple such nodes with a given
1780 * host side hardware endpoint + direction; scheduling may activate
1781 * that hardware endpoint.
1783 static int musb_schedule(
1790 int best_end, epnum;
1791 struct musb_hw_ep *hw_ep = NULL;
1792 struct list_head *head = NULL;
1795 struct urb *urb = next_urb(qh);
1797 /* use fixed hardware for control and bulk */
1798 if (qh->type == USB_ENDPOINT_XFER_CONTROL) {
1799 head = &musb->control;
1800 hw_ep = musb->control_ep;
1804 /* else, periodic transfers get muxed to other endpoints */
1807 * We know this qh hasn't been scheduled, so all we need to do
1808 * is choose which hardware endpoint to put it on ...
1810 * REVISIT what we really want here is a regular schedule tree
1811 * like e.g. OHCI uses.
1816 for (epnum = 1, hw_ep = musb->endpoints + 1;
1817 epnum < musb->nr_endpoints;
1821 if (musb_ep_get_qh(hw_ep, is_in) != NULL)
1824 if (hw_ep == musb->bulk_ep)
1828 diff = hw_ep->max_packet_sz_rx;
1830 diff = hw_ep->max_packet_sz_tx;
1831 diff -= (qh->maxpacket * qh->hb_mult);
1833 if (diff >= 0 && best_diff > diff) {
1836 * Mentor controller has a bug in that if we schedule
1837 * a BULK Tx transfer on an endpoint that had earlier
1838 * handled ISOC then the BULK transfer has to start on
1839 * a zero toggle. If the BULK transfer starts on a 1
1840 * toggle then this transfer will fail as the mentor
1841 * controller starts the Bulk transfer on a 0 toggle
1842 * irrespective of the programming of the toggle bits
1843 * in the TXCSR register. Check for this condition
1844 * while allocating the EP for a Tx Bulk transfer. If
1847 hw_ep = musb->endpoints + epnum;
1848 toggle = usb_gettoggle(urb->dev, qh->epnum, !is_in);
1849 txtype = (musb_readb(hw_ep->regs, MUSB_TXTYPE)
1851 if (!is_in && (qh->type == USB_ENDPOINT_XFER_BULK) &&
1852 toggle && (txtype == USB_ENDPOINT_XFER_ISOC))
1859 /* use bulk reserved ep1 if no other ep is free */
1860 if (best_end < 0 && qh->type == USB_ENDPOINT_XFER_BULK) {
1861 hw_ep = musb->bulk_ep;
1863 head = &musb->in_bulk;
1865 head = &musb->out_bulk;
1867 /* Enable bulk RX NAK timeout scheme when bulk requests are
1868 * multiplexed. This scheme doen't work in high speed to full
1869 * speed scenario as NAK interrupts are not coming from a
1870 * full speed device connected to a high speed device.
1871 * NAK timeout interval is 8 (128 uframe or 16ms) for HS and
1872 * 4 (8 frame or 8ms) for FS device.
1874 if (is_in && qh->dev)
1876 (USB_SPEED_HIGH == qh->dev->speed) ? 8 : 4;
1878 } else if (best_end < 0) {
1884 hw_ep = musb->endpoints + best_end;
1885 dev_dbg(musb->controller, "qh %p periodic slot %d\n", qh, best_end);
1888 idle = list_empty(head);
1889 list_add_tail(&qh->ring, head);
1893 qh->hep->hcpriv = qh;
1895 musb_start_urb(musb, is_in, qh);
1900 /* check if transaction translator is needed for device */
1901 static int tt_needed(struct musb *musb, struct usb_device *dev)
1903 if ((musb_readb(musb->mregs, MUSB_POWER) & MUSB_POWER_HSMODE) &&
1904 (dev->speed < USB_SPEED_HIGH))
1911 static int musb_urb_enqueue(
1913 int musb_urb_enqueue(
1915 struct usb_hcd *hcd,
1919 unsigned long flags;
1920 struct musb *musb = hcd_to_musb(hcd);
1921 struct usb_host_endpoint *hep = urb->ep;
1923 struct usb_endpoint_descriptor *epd = &hep->desc;
1928 /* host role must be active */
1929 if (!is_host_active(musb) || !musb->is_active)
1932 spin_lock_irqsave(&musb->lock, flags);
1933 ret = usb_hcd_link_urb_to_ep(hcd, urb);
1934 qh = ret ? NULL : hep->hcpriv;
1937 spin_unlock_irqrestore(&musb->lock, flags);
1939 /* DMA mapping was already done, if needed, and this urb is on
1940 * hep->urb_list now ... so we're done, unless hep wasn't yet
1941 * scheduled onto a live qh.
1943 * REVISIT best to keep hep->hcpriv valid until the endpoint gets
1944 * disabled, testing for empty qh->ring and avoiding qh setup costs
1945 * except for the first urb queued after a config change.
1950 /* Allocate and initialize qh, minimizing the work done each time
1951 * hw_ep gets reprogrammed, or with irqs blocked. Then schedule it.
1953 * REVISIT consider a dedicated qh kmem_cache, so it's harder
1954 * for bugs in other kernel code to break this driver...
1956 qh = kzalloc(sizeof *qh, mem_flags);
1958 spin_lock_irqsave(&musb->lock, flags);
1959 usb_hcd_unlink_urb_from_ep(hcd, urb);
1960 spin_unlock_irqrestore(&musb->lock, flags);
1966 INIT_LIST_HEAD(&qh->ring);
1969 qh->maxpacket = usb_endpoint_maxp(epd);
1970 qh->type = usb_endpoint_type(epd);
1972 /* Bits 11 & 12 of wMaxPacketSize encode high bandwidth multiplier.
1973 * Some musb cores don't support high bandwidth ISO transfers; and
1974 * we don't (yet!) support high bandwidth interrupt transfers.
1976 qh->hb_mult = 1 + ((qh->maxpacket >> 11) & 0x03);
1977 if (qh->hb_mult > 1) {
1978 int ok = (qh->type == USB_ENDPOINT_XFER_ISOC);
1981 ok = (usb_pipein(urb->pipe) && musb->hb_iso_rx)
1982 || (usb_pipeout(urb->pipe) && musb->hb_iso_tx);
1987 qh->maxpacket &= 0x7ff;
1990 qh->epnum = usb_endpoint_num(epd);
1992 /* NOTE: urb->dev->devnum is wrong during SET_ADDRESS */
1993 qh->addr_reg = (u8) usb_pipedevice(urb->pipe);
1995 /* precompute rxtype/txtype/type0 register */
1996 type_reg = (qh->type << 4) | qh->epnum;
1997 switch (urb->dev->speed) {
2001 case USB_SPEED_FULL:
2007 qh->type_reg = type_reg;
2009 /* Precompute RXINTERVAL/TXINTERVAL register */
2011 case USB_ENDPOINT_XFER_INT:
2013 * Full/low speeds use the linear encoding,
2014 * high speed uses the logarithmic encoding.
2016 if (urb->dev->speed <= USB_SPEED_FULL) {
2017 interval = max_t(u8, epd->bInterval, 1);
2021 case USB_ENDPOINT_XFER_ISOC:
2022 /* ISO always uses logarithmic encoding */
2023 interval = min_t(u8, epd->bInterval, 16);
2026 /* REVISIT we actually want to use NAK limits, hinting to the
2027 * transfer scheduling logic to try some other qh, e.g. try
2030 * interval = (USB_SPEED_HIGH == urb->dev->speed) ? 16 : 2;
2032 * The downside of disabling this is that transfer scheduling
2033 * gets VERY unfair for nonperiodic transfers; a misbehaving
2034 * peripheral could make that hurt. That's perfectly normal
2035 * for reads from network or serial adapters ... so we have
2036 * partial NAKlimit support for bulk RX.
2038 * The upside of disabling it is simpler transfer scheduling.
2042 qh->intv_reg = interval;
2044 /* precompute addressing for external hub/tt ports */
2045 if (musb->is_multipoint) {
2047 struct usb_device *parent = urb->dev->parent;
2049 struct usb_device *parent = usb_dev_get_parent(urb->dev);
2053 if (parent != hcd->self.root_hub) {
2057 qh->h_addr_reg = (u8) parent->devnum;
2060 /* set up tt info if needed */
2062 qh->h_port_reg = (u8) urb->dev->ttport;
2063 if (urb->dev->tt->hub)
2065 (u8) urb->dev->tt->hub->devnum;
2066 if (urb->dev->tt->multi)
2067 qh->h_addr_reg |= 0x80;
2070 if (tt_needed(musb, urb->dev)) {
2072 uint8_t hubaddr = 0;
2073 usb_find_usb2_hub_address_port(urb->dev,
2076 qh->h_addr_reg = hubaddr;
2077 qh->h_port_reg = portnr;
2083 /* invariant: hep->hcpriv is null OR the qh that's already scheduled.
2084 * until we get real dma queues (with an entry for each urb/buffer),
2085 * we only have work to do in the former case.
2087 spin_lock_irqsave(&musb->lock, flags);
2089 /* some concurrent activity submitted another urb to hep...
2090 * odd, rare, error prone, but legal.
2096 ret = musb_schedule(musb, qh,
2097 epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK);
2101 /* FIXME set urb->start_frame for iso/intr, it's tested in
2102 * musb_start_urb(), but otherwise only konicawc cares ...
2105 spin_unlock_irqrestore(&musb->lock, flags);
2109 spin_lock_irqsave(&musb->lock, flags);
2110 usb_hcd_unlink_urb_from_ep(hcd, urb);
2111 spin_unlock_irqrestore(&musb->lock, flags);
2118 * abort a transfer that's at the head of a hardware queue.
2119 * called with controller locked, irqs blocked
2120 * that hardware queue advances to the next transfer, unless prevented
2122 static int musb_cleanup_urb(struct urb *urb, struct musb_qh *qh)
2124 struct musb_hw_ep *ep = qh->hw_ep;
2125 struct musb *musb = ep->musb;
2126 void __iomem *epio = ep->regs;
2127 unsigned hw_end = ep->epnum;
2128 void __iomem *regs = ep->musb->mregs;
2129 int is_in = usb_pipein(urb->pipe);
2133 musb_ep_select(regs, hw_end);
2135 if (is_dma_capable()) {
2136 struct dma_channel *dma;
2138 dma = is_in ? ep->rx_channel : ep->tx_channel;
2140 status = ep->musb->dma_controller->channel_abort(dma);
2141 dev_dbg(musb->controller,
2142 "abort %cX%d DMA for urb %p --> %d\n",
2143 is_in ? 'R' : 'T', ep->epnum,
2145 urb->actual_length += dma->actual_len;
2149 /* turn off DMA requests, discard state, stop polling ... */
2150 if (ep->epnum && is_in) {
2151 /* giveback saves bulk toggle */
2152 csr = musb_h_flush_rxfifo(ep, 0);
2154 /* REVISIT we still get an irq; should likely clear the
2155 * endpoint's irq status here to avoid bogus irqs.
2156 * clearing that status is platform-specific...
2158 } else if (ep->epnum) {
2159 musb_h_tx_flush_fifo(ep);
2160 csr = musb_readw(epio, MUSB_TXCSR);
2161 csr &= ~(MUSB_TXCSR_AUTOSET
2162 | MUSB_TXCSR_DMAENAB
2163 | MUSB_TXCSR_H_RXSTALL
2164 | MUSB_TXCSR_H_NAKTIMEOUT
2165 | MUSB_TXCSR_H_ERROR
2166 | MUSB_TXCSR_TXPKTRDY);
2167 musb_writew(epio, MUSB_TXCSR, csr);
2168 /* REVISIT may need to clear FLUSHFIFO ... */
2169 musb_writew(epio, MUSB_TXCSR, csr);
2170 /* flush cpu writebuffer */
2171 csr = musb_readw(epio, MUSB_TXCSR);
2173 musb_h_ep0_flush_fifo(ep);
2176 musb_advance_schedule(ep->musb, urb, ep, is_in);
2181 static int musb_urb_dequeue(
2183 int musb_urb_dequeue(
2185 struct usb_hcd *hcd,
2189 struct musb *musb = hcd_to_musb(hcd);
2191 unsigned long flags;
2192 int is_in = usb_pipein(urb->pipe);
2195 dev_dbg(musb->controller, "urb=%p, dev%d ep%d%s\n", urb,
2196 usb_pipedevice(urb->pipe),
2197 usb_pipeendpoint(urb->pipe),
2198 is_in ? "in" : "out");
2200 spin_lock_irqsave(&musb->lock, flags);
2201 ret = usb_hcd_check_unlink_urb(hcd, urb, status);
2210 * Any URB not actively programmed into endpoint hardware can be
2211 * immediately given back; that's any URB not at the head of an
2212 * endpoint queue, unless someday we get real DMA queues. And even
2213 * if it's at the head, it might not be known to the hardware...
2215 * Otherwise abort current transfer, pending DMA, etc.; urb->status
2216 * has already been updated. This is a synchronous abort; it'd be
2217 * OK to hold off until after some IRQ, though.
2219 * NOTE: qh is invalid unless !list_empty(&hep->urb_list)
2222 || urb->urb_list.prev != &qh->hep->urb_list
2223 || musb_ep_get_qh(qh->hw_ep, is_in) != qh) {
2224 int ready = qh->is_ready;
2227 musb_giveback(musb, urb, 0);
2228 qh->is_ready = ready;
2230 /* If nothing else (usually musb_giveback) is using it
2231 * and its URB list has emptied, recycle this qh.
2233 if (ready && list_empty(&qh->hep->urb_list)) {
2234 qh->hep->hcpriv = NULL;
2235 list_del(&qh->ring);
2239 ret = musb_cleanup_urb(urb, qh);
2241 spin_unlock_irqrestore(&musb->lock, flags);
2246 /* disable an endpoint */
2248 musb_h_disable(struct usb_hcd *hcd, struct usb_host_endpoint *hep)
2250 u8 is_in = hep->desc.bEndpointAddress & USB_DIR_IN;
2251 unsigned long flags;
2252 struct musb *musb = hcd_to_musb(hcd);
2256 spin_lock_irqsave(&musb->lock, flags);
2262 /* NOTE: qh is invalid unless !list_empty(&hep->urb_list) */
2264 /* Kick the first URB off the hardware, if needed */
2266 if (musb_ep_get_qh(qh->hw_ep, is_in) == qh) {
2269 /* make software (then hardware) stop ASAP */
2271 urb->status = -ESHUTDOWN;
2274 musb_cleanup_urb(urb, qh);
2276 /* Then nuke all the others ... and advance the
2277 * queue on hw_ep (e.g. bulk ring) when we're done.
2279 while (!list_empty(&hep->urb_list)) {
2281 urb->status = -ESHUTDOWN;
2282 musb_advance_schedule(musb, urb, qh->hw_ep, is_in);
2285 /* Just empty the queue; the hardware is busy with
2286 * other transfers, and since !qh->is_ready nothing
2287 * will activate any of these as it advances.
2289 while (!list_empty(&hep->urb_list))
2290 musb_giveback(musb, next_urb(qh), -ESHUTDOWN);
2293 list_del(&qh->ring);
2297 spin_unlock_irqrestore(&musb->lock, flags);
2300 static int musb_h_get_frame_number(struct usb_hcd *hcd)
2302 struct musb *musb = hcd_to_musb(hcd);
2304 return musb_readw(musb->mregs, MUSB_FRAME);
2307 static int musb_h_start(struct usb_hcd *hcd)
2309 struct musb *musb = hcd_to_musb(hcd);
2311 /* NOTE: musb_start() is called when the hub driver turns
2312 * on port power, or when (OTG) peripheral starts.
2314 hcd->state = HC_STATE_RUNNING;
2315 musb->port1_status = 0;
2319 static void musb_h_stop(struct usb_hcd *hcd)
2321 musb_stop(hcd_to_musb(hcd));
2322 hcd->state = HC_STATE_HALT;
2325 static int musb_bus_suspend(struct usb_hcd *hcd)
2327 struct musb *musb = hcd_to_musb(hcd);
2330 if (!is_host_active(musb))
2333 switch (musb->xceiv->state) {
2334 case OTG_STATE_A_SUSPEND:
2336 case OTG_STATE_A_WAIT_VRISE:
2337 /* ID could be grounded even if there's no device
2338 * on the other end of the cable. NOTE that the
2339 * A_WAIT_VRISE timers are messy with MUSB...
2341 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
2342 if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS)
2343 musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
2349 if (musb->is_active) {
2350 WARNING("trying to suspend as %s while active\n",
2351 otg_state_string(musb->xceiv->state));
2357 static int musb_bus_resume(struct usb_hcd *hcd)
2359 /* resuming child port does the work */
2363 const struct hc_driver musb_hc_driver = {
2364 .description = "musb-hcd",
2365 .product_desc = "MUSB HDRC host driver",
2366 .hcd_priv_size = sizeof(struct musb),
2367 .flags = HCD_USB2 | HCD_MEMORY,
2369 /* not using irq handler or reset hooks from usbcore, since
2370 * those must be shared with peripheral code for OTG configs
2373 .start = musb_h_start,
2374 .stop = musb_h_stop,
2376 .get_frame_number = musb_h_get_frame_number,
2378 .urb_enqueue = musb_urb_enqueue,
2379 .urb_dequeue = musb_urb_dequeue,
2380 .endpoint_disable = musb_h_disable,
2382 .hub_status_data = musb_hub_status_data,
2383 .hub_control = musb_hub_control,
2384 .bus_suspend = musb_bus_suspend,
2385 .bus_resume = musb_bus_resume,
2386 /* .start_port_reset = NULL, */
2387 /* .hub_irq_enable = NULL, */