2 * Xilinx xps_ll_temac ethernet driver for u-boot
6 * Copyright (C) 2011 - 2012 Stephan Linz <linz@li-pro.net>
7 * Copyright (C) 2008 - 2011 Michal Simek <monstr@monstr.eu>
8 * Copyright (C) 2008 - 2011 PetaLogix
10 * Based on Yoshio Kashiwagi kashiwagi@co-nss.co.jp driver
11 * Copyright (C) 2008 Nissin Systems Co.,Ltd.
14 * CREDITS: tsec driver
16 * SPDX-License-Identifier: GPL-2.0+
18 * [0]: http://www.xilinx.com/support/documentation
20 * [S]: [0]/ip_documentation/xps_ll_temac.pdf
21 * [A]: [0]/application_notes/xapp1041.pdf
31 #include "xilinx_ll_temac.h"
32 #include "xilinx_ll_temac_mdio.h"
34 #if !defined(CONFIG_MII)
35 # error "LL_TEMAC requires MII -- missing CONFIG_MII"
38 #if !defined(CONFIG_PHYLIB)
39 # error "LL_TEMAC requires PHYLIB -- missing CONFIG_PHYLIB"
43 * Prior to PHY access, the MDIO clock must be setup. This driver will set a
44 * safe default that should work with PLB bus speeds of up to 150 MHz and keep
45 * the MDIO clock below 2.5 MHz. If the user wishes faster access to the PHY
46 * then the clock divisor can be set to a different value by setting the
47 * correct bus speed value with CONFIG_XILINX_LL_TEMAC_CLK.
49 #if !defined(CONFIG_XILINX_LL_TEMAC_CLK)
50 #define MDIO_CLOCK_DIV MC_CLKDIV_10(150000000)
52 #define MDIO_CLOCK_DIV MC_CLKDIV_25(CONFIG_XILINX_LL_TEMAC_CLK)
55 static int ll_temac_mdio_setup(struct mii_dev *bus)
57 struct temac_reg *regs = (struct temac_reg *)bus->priv;
59 /* setup MDIO clock */
60 ll_temac_indirect_set(regs, TEMAC_MC,
61 MC_MDIOEN | (MDIO_CLOCK_DIV & MC_CLKDIV_MASK));
67 * Indirect MII PHY read via ll_temac.
69 * http://www.xilinx.com/support/documentation/ip_documentation/xps_ll_temac.pdf
70 * page 67, Using the MII Management to Access PHY Registers
72 int ll_temac_local_mdio_read(struct temac_reg *regs, int addr, int devad,
76 ((addr << LSW_PHYAD_POS) & LSW_PHYAD_MASK) |
77 (regnum & LSW_REGAD_MASK));
78 out_be32(®s->ctl, TEMAC_MIIMAI);
80 ll_temac_check_status(regs, RSE_MIIM_RR);
82 return in_be32(®s->lsw) & LSW_REGDAT_MASK;
86 * Indirect MII PHY write via ll_temac.
88 * http://www.xilinx.com/support/documentation/ip_documentation/xps_ll_temac.pdf
89 * page 67, Using the MII Management to Access PHY Registers
91 void ll_temac_local_mdio_write(struct temac_reg *regs, int addr, int devad,
92 int regnum, u16 value)
94 out_be32(®s->lsw, (value & LSW_REGDAT_MASK));
95 out_be32(®s->ctl, CTL_WEN | TEMAC_MIIMWD);
98 ((addr << LSW_PHYAD_POS) & LSW_PHYAD_MASK) |
99 (regnum & LSW_REGAD_MASK));
100 out_be32(®s->ctl, CTL_WEN | TEMAC_MIIMAI);
102 ll_temac_check_status(regs, RSE_MIIM_WR);
105 int ll_temac_phy_read(struct mii_dev *bus, int addr, int devad, int regnum)
107 struct temac_reg *regs = (struct temac_reg *)bus->priv;
109 return ll_temac_local_mdio_read(regs, addr, devad, regnum);
112 int ll_temac_phy_write(struct mii_dev *bus, int addr, int devad, int regnum,
115 struct temac_reg *regs = (struct temac_reg *)bus->priv;
117 ll_temac_local_mdio_write(regs, addr, devad, regnum, value);
123 * Use MII register 1 (MII status register) to detect PHY
125 * A Mask used to verify certain PHY features (register content)
126 * in the PHY detection register:
127 * Auto-negotiation support, 10Mbps half/full duplex support
129 #define PHY_DETECT_REG MII_BMSR
130 #define PHY_DETECT_MASK (BMSR_10FULL | BMSR_10HALF | BMSR_ANEGCAPABLE)
132 /* Looking for a valid PHY address */
133 int ll_temac_phy_addr(struct mii_dev *bus)
135 struct temac_reg *regs = (struct temac_reg *)bus->priv;
139 for (phy = PHY_MAX_ADDR; phy >= 0; phy--) {
140 val = ll_temac_local_mdio_read(regs, phy, 0, PHY_DETECT_REG);
141 if ((val != 0xFFFF) &&
142 ((val & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
143 /* Found a valid PHY address */
151 int xilinx_ll_temac_mdio_initialize(bd_t *bis, struct ll_temac_mdio_info *info)
153 struct mii_dev *bus = mdio_alloc();
156 printf("Failed to allocate LL_TEMAC MDIO bus: %s\n",
161 bus->read = ll_temac_phy_read;
162 bus->write = ll_temac_phy_write;
165 /* use given name or generate its own unique name */
167 strncpy(bus->name, info->name, MDIO_NAME_LEN);
169 snprintf(bus->name, MDIO_NAME_LEN, "lltemii.%p", info->regs);
170 info->name = bus->name;
173 bus->priv = info->regs;
175 ll_temac_mdio_setup(bus);
176 return mdio_register(bus);