3 bool "Bit-banged ethernet MII management channel support"
5 config MV88E6352_SWITCH
6 bool "Marvell 88E6352 switch support"
9 bool "Ethernet PHY (physical media interface) support"
12 Enable Ethernet PHY (physical media interface) support.
17 bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
19 Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches.
20 This currently supports BCM53125 and similar models.
29 hex "Bitmask of PHY ports"
33 config MV88E61XX_SWITCH
34 bool "Marvel MV88E61xx Ethernet switch PHY support."
38 config MV88E61XX_CPU_PORT
41 config MV88E61XX_PHY_PORTS
42 hex "Bitmask of PHY Ports"
44 config MV88E61XX_FIXED_PORTS
45 hex "Bitmask of PHYless serdes Ports"
47 endif # MV88E61XX_SWITCH
50 bool "Generic 10G PHY support"
53 bool "Aquantia Ethernet PHYs support"
56 bool "Atheros Ethernet PHYs support"
59 bool "Broadcom Ethernet PHYs support"
62 bool "Cortina Ethernet PHYs support"
65 bool "Davicom Ethernet PHYs support"
68 bool "LSI TruePHY ET1011C support"
71 bool "LXT971 Ethernet PHY support"
74 bool "Marvell Ethernet PHYs support"
77 bool "Amlogic Meson GXL Internal PHY support"
80 bool "Micrel Ethernet PHYs support"
82 Enable support for the GbE PHYs manufactured by Micrel (now
83 a part of Microchip). This includes drivers for the KSZ804,
84 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, KSZ8721
85 either/or KSZ9021 (see the "Micrel KSZ9021 family support"
86 config option for details), and KSZ9031 (if configured).
90 config PHY_MICREL_KSZ9021
93 select PHY_MICREL_KSZ90X1
95 config PHY_MICREL_KSZ9031
98 select PHY_MICREL_KSZ90X1
100 config PHY_MICREL_KSZ90X1
101 bool "Micrel KSZ90x1 family support"
104 Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If
105 enabled, the extended register read/write for KSZ90x1 PHYs
106 is supported through the 'mdio' command and any RGMII signal
107 delays configured in the device tree will be applied to the
108 PHY during initialization.
110 This should not be enabled at the same time with PHY_MICREL_KSZ8XXX
111 as the KSZ9021 and KS8721 share the same ID.
113 config PHY_MICREL_KSZ8XXX
114 bool "Micrel KSZ8xxx family support"
115 default y if !PHY_MICREL_KSZ90X1
117 Enable support for the 8000 series GbE PHYs manufactured by Micrel
118 (now a part of Microchip). This includes drivers for the KSZ804,
119 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721.
121 This should not be enabled at the same time with PHY_MICREL_KSZ90X1
122 as the KSZ9021 and KS8721 share the same ID.
127 bool "Microsemi Corp Ethernet PHYs support"
130 bool "National Semiconductor Ethernet PHYs support"
133 bool "Realtek Ethernet PHYs support"
135 config RTL8211X_PHY_FORCE_MASTER
136 bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
137 depends on PHY_REALTEK
139 Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
140 This can work around link stability and data corruption issues on gigabit
141 links which can occur in slave mode on certain PHYs, e.g. on the
144 Please note that two directly connected devices (i.e. via crossover cable)
145 will not be able to establish a link between each other if they both force
146 master mode. Multiple devices forcing master mode when connected by a
147 network switch do not pose a problem as the switch configures its affected
148 ports into slave mode.
150 This option only affects gigabit links. If you must establish a direct
151 connection between two devices which both force master mode, try forcing
152 the link speed to 100MBit/s.
157 bool "Microchip(SMSC) Ethernet PHYs support"
159 config PHY_TERANETICS
160 bool "Teranetics Ethernet PHYs support"
163 bool "Texas Instruments Ethernet PHYs support"
166 bool "Vitesse Ethernet PHYs support"
169 bool "Xilinx Ethernet PHYs support"
172 bool "Fixed-Link PHY"
175 Fixed PHY is used for having a 'fixed-link' to another MAC with a direct
176 connection (MII, RGMII, ...).
177 There is nothing like autoneogation and so
178 on, the link is always up with fixed speed and fixed duplex-setting.
179 More information: doc/device-tree-bindings/net/fixed-link.txt