3 bool "Bit-banged ethernet MII management channel support"
5 config MV88E6352_SWITCH
6 bool "Marvell 88E6352 switch support"
9 bool "Ethernet PHY (physical media interface) support"
11 Enable Ethernet PHY (physical media interface) support.
15 config MV88E61XX_SWITCH
16 bool "Marvel MV88E61xx Ethernet switch PHY support."
20 config MV88E61XX_CPU_PORT
23 config MV88E61XX_PHY_PORTS
24 hex "Bitmask of PHY Ports"
26 config MV88E61XX_FIXED_PORTS
27 hex "Bitmask of PHYless serdes Ports"
29 endif # MV88E61XX_SWITCH
32 bool "Generic 10G PHY support"
35 bool "Aquantia Ethernet PHYs support"
38 bool "Atheros Ethernet PHYs support"
41 bool "Broadcom Ethernet PHYs support"
44 bool "Cortina Ethernet PHYs support"
47 bool "Davicom Ethernet PHYs support"
50 bool "LSI TruePHY ET1011C support"
53 bool "LXT971 Ethernet PHY support"
56 bool "Marvell Ethernet PHYs support"
59 bool "Micrel Ethernet PHYs support"
61 Enable support for the GbE PHYs manufactured by Micrel (now
62 a part of Microchip). This includes drivers for the KSZ804,
63 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, KSZ8721
64 either/or KSZ9021 (see the "Micrel KSZ9021 family support"
65 config option for details), and KSZ9031 (if configured).
69 config PHY_MICREL_KSZ9021
70 bool "Micrel KSZ9021 family support"
73 Enable support for the Micrel KSZ9021 GbE PHY family. If
74 enabled, the extended register read/write for KSZ9021 PHYs
75 is supported through the 'mdio' command and any RGMII signal
76 delays configured in the device tree will be applied to the
77 PHY during initialisation.
79 Note that the KSZ9021 uses the same part number os the
80 KSZ8921BL, so enabling this option disables support for the
83 config PHY_MICREL_KSZ9031
84 bool "Micrel KSZ9031 family support"
87 Enable support for the Micrel KSZ9031 GbE PHY family. If
88 enabled, the extended register read/write for KSZ9021 PHYs
89 is supported through the 'mdio' command and any RGMII signal
90 delays configured in the device tree will be applied to the
91 PHY during initialisatioin.
96 bool "Microsemi Corp Ethernet PHYs support"
99 bool "National Semiconductor Ethernet PHYs support"
102 bool "Realtek Ethernet PHYs support"
104 config RTL8211X_PHY_FORCE_MASTER
105 bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
106 depends on PHY_REALTEK
108 Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
109 This can work around link stability and data corruption issues on gigabit
110 links which can occur in slave mode on certain PHYs, e.g. on the
113 Please note that two directly connected devices (i.e. via crossover cable)
114 will not be able to establish a link between each other if they both force
115 master mode. Multiple devices forcing master mode when connected by a
116 network switch do not pose a problem as the switch configures its affected
117 ports into slave mode.
119 This option only affects gigabit links. If you must establish a direct
120 connection between two devices which both force master mode, try forcing
121 the link speed to 100MBit/s.
126 bool "Microchip(SMSC) Ethernet PHYs support"
128 config PHY_TERANETICS
129 bool "Teranetics Ethernet PHYs support"
132 bool "Texas Instruments Ethernet PHYs support"
135 bool "Vitesse Ethernet PHYs support"
138 bool "Xilinx Ethernet PHYs support"
141 bool "Fixed-Link PHY"
144 Fixed PHY is used for having a 'fixed-link' to another MAC with a direct
145 connection (MII, RGMII, ...).
146 There is nothing like autoneogation and so
147 on, the link is always up with fixed speed and fixed duplex-setting.
148 More information: doc/device-tree-bindings/net/fixed-link.txt