1 # SPDX-License-Identifier: GPL-2.0-only
3 # TI device configuration
7 bool "Texas Instruments (TI) devices"
9 depends on PCI || EISA || AR7 || ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE
11 If you have a network (Ethernet) card belonging to this class, say Y.
13 Note that the answer to this question doesn't directly affect the
14 kernel: saying N will just cause the configurator to skip all
15 the questions about TI devices. If you say Y, you will be asked for
16 your specific card in the following questions.
20 config TI_DAVINCI_EMAC
21 tristate "TI DaVinci EMAC Support"
22 depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 ) || COMPILE_TEST
23 select TI_DAVINCI_MDIO
26 This driver supports TI's DaVinci Ethernet .
28 To compile this driver as a module, choose M here: the module
29 will be called davinci_emac_driver. This is recommended.
31 config TI_DAVINCI_MDIO
32 tristate "TI DaVinci MDIO Support"
33 depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST
36 This driver supports TI's DaVinci MDIO module.
38 To compile this driver as a module, choose M here: the module
39 will be called davinci_mdio. This is recommended.
41 config TI_CPSW_PHY_SEL
42 bool "TI CPSW Phy mode Selection (DEPRECATED)"
45 This driver supports configuring of the phy mode connected to
46 the CPSW. DEPRECATED: use PHY_TI_GMII_SEL.
49 tristate "TI CPSW Switch Support"
50 depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST
51 select TI_DAVINCI_MDIO
56 This driver supports TI's CPSW Ethernet Switch.
58 To compile this driver as a module, choose M here: the module
62 bool "TI Common Platform Time Sync (CPTS) Support"
63 depends on TI_CPSW || TI_KEYSTONE_NETCP || COMPILE_TEST
65 depends on POSIX_TIMERS
67 This driver supports the Common Platform Time Sync unit of
68 the CPSW Ethernet Switch and Keystone 2 1g/10g Switch Subsystem.
69 The unit can time stamp PTP UDP/IPv4 and Layer 2 packets, and the
70 driver offers a PTP Hardware Clock.
75 default y if TI_CPSW=y || TI_KEYSTONE_NETCP=y
76 select NET_PTP_CLASSIFY
80 config TI_KEYSTONE_NETCP
81 tristate "TI Keystone NETCP Core Support"
82 select TI_DAVINCI_MDIO
84 depends on KEYSTONE_NAVIGATOR_DMA && KEYSTONE_NAVIGATOR_QMSS
86 This driver supports TI's Keystone NETCP Core.
88 To compile this driver as a module, choose M here: the module
89 will be called keystone_netcp.
91 config TI_KEYSTONE_NETCP_ETHSS
92 depends on TI_KEYSTONE_NETCP
93 tristate "TI Keystone NETCP Ethernet subsystem Support"
96 To compile this driver as a module, choose M here: the module
97 will be called keystone_netcp_ethss.
100 tristate "TI ThunderLAN support"
101 depends on (PCI || EISA)
103 If you have a PCI Ethernet network card based on the ThunderLAN chip
104 which is supported by this driver, say Y here.
106 Devices currently supported by this driver are Compaq Netelligent,
107 Compaq NetFlex and Olicom cards. Please read the file
108 <file:Documentation/networking/device_drivers/ti/tlan.txt>
111 To compile this driver as a module, choose M here. The module
114 Please email feedback to <torben.mathiasen@compaq.com>.
117 tristate "TI AR7 CPMAC Ethernet support"
121 TI AR7 CPMAC Ethernet support
123 endif # NET_VENDOR_TI