1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
5 bool "Enable Driver Model for Ethernet drivers"
8 Enable driver model for Ethernet.
10 The eth_*() interface will be implemented by the UCLASS_ETH class
11 This is currently implemented in net/eth-uclass.c
12 Look in include/net.h for details.
15 bool "TI Common Platform Ethernet Switch"
18 This driver supports the TI three port switch gigabit ethernet
19 subsystem found in the TI SoCs.
22 bool "Network device support"
26 You must select Y to enable any network device support
27 Generally if you have any networking support this is a given
34 bool "Enable GbE PHY status parsing and configuration"
36 Enables support for parsing the status output and for
37 configuring GbE PHYs (affects the inner workings of some
38 commands and miiphyutil.c).
41 bool "Atheros AG7xxx Ethernet MAC support"
42 depends on DM_ETH && ARCH_ATH79
45 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
46 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
50 bool "Altera Triple-Speed Ethernet MAC support"
54 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
55 Please find details on the "Triple-Speed Ethernet MegaCore Function
56 Resource Center" of Altera.
59 bool "Broadcom SF2 (Starfighter2) Ethernet support"
62 This is an abstract framework which provides a generic interface
63 to MAC and DMA management for multiple Broadcom SoCs such as
64 Cygnus, NSP and bcm28155_ap platforms.
66 config BCM_SF2_ETH_DEFAULT_PORT
67 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
68 depends on BCM_SF2_ETH
71 Default port number for the Starfighter2 ethernet driver.
73 config BCM_SF2_ETH_GMAC
74 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
75 depends on BCM_SF2_ETH
77 This flag enables the ethernet support for Broadcom platforms with
78 GMAC such as Cygnus. This driver is based on the framework provided
79 by the BCM_SF2_ETH driver.
80 Say Y to any bcmcygnus based platforms.
83 bool "Synopsys DWC Ethernet QOS device support"
87 This driver supports the Synopsys Designware Ethernet QOS (Quality
88 Of Service) IP block. The IP supports many options for bus type,
89 clocking/reset structure, and feature list. This driver currently
90 supports the specific configuration used in NVIDIA's Tegra186 chip,
91 but should be extensible to other combinations quite easily.
94 bool "Intel PRO/1000 Gigabit Ethernet support"
96 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
97 adapters. For more information on how to identify your adapter, go
98 to the Adapter & Driver ID Guide at:
100 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
102 config E1000_SPI_GENERIC
103 bool "Allow access to the Intel 8257x SPI bus"
106 Allow generic access to the SPI bus on the Intel 8257x, for
107 example with the "sspi" command.
110 bool "Enable SPI bus utility code"
113 Utility code for direct access to the SPI bus on Intel 8257x.
114 This does not do anything useful unless you set at least one
115 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
118 bool "Enable the e1000 command"
121 This enables the 'e1000' management command for E1000 devices. When
122 used on devices with SPI support you can reprogram the EEPROM from
126 depends on DM_ETH && SANDBOX
128 bool "Sandbox: Mocked Ethernet driver"
130 This driver simply responds with fake ARP replies and ping
131 replies that are used to verify network stack functionality
133 This driver is particularly useful in the test/dm/eth.c tests
135 config ETH_SANDBOX_RAW
136 depends on DM_ETH && SANDBOX
138 bool "Sandbox: Bridge to Linux Raw Sockets"
140 This driver is a bridge from the bottom of the network stack
141 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
142 network traffic to be tested from within sandbox. See
143 board/sandbox/README.sandbox for more details.
145 config ETH_DESIGNWARE
146 bool "Synopsys Designware Ethernet MAC"
149 This MAC is present in SoCs from various vendors. It supports
150 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
151 provide the PHY (physical media interface).
153 config ETH_DESIGNWARE_SOCFPGA
154 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
155 depends on DM_ETH && ETH_DESIGNWARE
157 The Altera SoCFPGA requires additional configuration of the
158 Altera system manager to correctly interface with the PHY.
159 This code handles those SoC specifics.
162 bool "OpenCores 10/100 Mbps Ethernet MAC"
164 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
166 config FEC_MXC_SHARE_MDIO
167 bool "Share the MDIO bus for FEC controller"
170 config FEC_MXC_MDIO_BASE
171 hex "MDIO base address for the FEC controller"
172 depends on FEC_MXC_SHARE_MDIO
174 This specifies the MDIO registers base address. It is used when
175 two FEC controllers share MDIO bus.
178 bool "FEC Ethernet controller"
179 depends on MX5 || MX6 || MX7
181 This driver supports the 10/100 Fast Ethernet controller for
185 bool "Ftmac100 Ethernet Support"
187 This MAC is present in Andestech SoCs.
190 bool "Marvell Orion5x/Kirkwood network interface support"
191 depends on KIRKWOOD || ORION5X
192 select PHYLIB if DM_ETH
194 This driver supports the network interface units in the
195 Marvell Orion5x and Kirkwood SoCs
198 bool "Marvell Armada XP/385/3700 network interface support"
199 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
202 This driver supports the network interface units in the
203 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
206 bool "Marvell Armada 375/7K/8K network interface support"
207 depends on ARMADA_375 || ARMADA_8K
210 This driver supports the network interface units in the
211 Marvell ARMADA 375, 7K and 8K SoCs.
214 bool "Cadence MACB/GEM Ethernet Interface"
218 The Cadence MACB ethernet interface is found on many Atmel
219 AT91 and SAMA5 parts. This driver also supports the Cadence
220 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
221 Say Y to include support for the MACB/GEM chip.
224 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
227 The Cadence MACB ethernet interface was used on Zynq platform.
228 Say Y to enable support for the MACB/GEM in Zynq chip.
231 bool "Intel Platform Controller Hub EG20T GMAC driver"
232 depends on DM_ETH && DM_PCI
235 This MAC is present in Intel Platform Controller Hub EG20T. It
236 supports 10/100/1000 Mbps operation.
241 Enable the support of the Reduced Gigabit Media-Independent
247 Enable support of the Media-Independent Interface (MII)
250 bool "Realtek 8139 series Ethernet controller driver"
252 This driver supports Realtek 8139 series fast ethernet family of
253 PCI chipsets/adapters.
256 bool "Realtek 8169 series Ethernet controller driver"
258 This driver supports Realtek 8169 series gigabit ethernet family of
259 PCI/PCIe chipsets/adapters.
262 bool "SMSC LAN911x and LAN921x controller driver"
267 hex "SMC911X Base Address"
269 Define this to hold the physical address
270 of the device (I/O space)
273 prompt "SMC911X bus width"
274 default SMC911X_16_BIT
276 config SMC911X_32_BIT
277 bool "Enable 32-bit interface"
279 config SMC911X_16_BIT
280 bool "Enable 16-bit interface"
282 Define this if data bus is 16 bits. If your processor
283 automatically converts one 32 bit word to two 16 bit
284 words you may also try CONFIG_SMC911X_32_BIT.
290 bool "Enable Allwinner GMAC Ethernet support"
292 Enable the support for Sun7i GMAC Ethernet controller
294 config SUN7I_GMAC_FORCE_TXERR
295 bool "Force PA17 as gmac function"
296 depends on SUN7I_GMAC
298 Some ethernet phys needs TXERR control. Since the GMAC
299 doesn't have such signal, setting PA17 as GMAC function
300 makes the pin output low, which enables data transmission.
303 bool "Allwinner Sun4i Ethernet MAC support"
307 This driver supports the Allwinner based SUN4I Ethernet MAC.
310 bool "Allwinner Sun8i Ethernet MAC support"
315 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
316 It can be found in H3/A64/A83T based SoCs and compatible with both
317 External and Internal PHYs.
320 bool "Renesas SH Ethernet MAC"
323 This driver supports the Ethernet for Renesas SH and ARM SoCs.
325 config DRIVER_TI_EMAC
326 bool "TI Davinci EMAC"
328 Support for davinci emac
330 config XILINX_AXIEMAC
331 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
334 bool "Xilinx AXI Ethernet"
336 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
338 config XILINX_EMACLITE
339 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
342 bool "Xilinx Ethernetlite"
344 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
347 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
349 bool "Xilinx Ethernet GEM"
351 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
354 bool "Microchip PIC32 Ethernet Support"
355 depends on DM_ETH && MACH_PIC32
358 This driver implements 10/100 Mbps Ethernet and MAC layer for
359 Microchip PIC32 microcontrollers.
362 bool "Rockchip Synopsys Designware Ethernet MAC"
363 depends on DM_ETH && ETH_DESIGNWARE
365 This driver provides Rockchip SoCs network support based on the
366 Synopsys Designware driver.
369 bool "Renesas Ethernet AVB MAC"
370 depends on DM_ETH && RCAR_GEN3
373 This driver implements support for the Ethernet AVB block in
374 Renesas M3 and H3 SoCs.
377 bool "Fast Ethernet Controller on MPC8XX"
381 This driver implements support for the Fast Ethernet Controller
385 bool "Socionext AVE Ethernet support"
386 depends on DM_ETH && ARCH_UNIPHIER
391 This driver implements support for the Socionext AVE Ethernet
392 controller, as found on the Socionext UniPhier family.
396 depends on MPC8XX_FEC
401 depends on ETHER_ON_FEC1
404 Define to the hardcoded PHY address which corresponds
405 to the given FEC; i. e.
406 #define CONFIG_FEC1_PHY 4
407 means that the PHY with address 4 is connected to FEC1
409 When set to -1, means to probe for first available.
413 depends on ETHER_ON_FEC1
416 The PHY does not have a RXERR line (RMII only).
417 (so program the FEC to ignore it).
421 depends on MPC8XX_FEC && MPC885
426 depends on ETHER_ON_FEC2
429 Define to the hardcoded PHY address which corresponds
430 to the given FEC; i. e.
431 #define CONFIG_FEC1_PHY 4
432 means that the PHY with address 4 is connected to FEC1
434 When set to -1, means to probe for first available.
436 config FEC2_PHY_NORXERR
438 depends on ETHER_ON_FEC2
441 The PHY does not have a RXERR line (RMII only).
442 (so program the FEC to ignore it).
444 config SYS_DPAA_QBMAN
445 bool "Device tree fixup for QBMan on freescale SOCs"
446 depends on (ARM || PPC) && !SPL_BUILD
447 default y if ARCH_B4860 || \
466 QBman fixups to allow deep sleep in DPAA 1 SOCs
470 bool "Enable Three-Speed Ethernet Controller"
472 This driver implements support for the (Enhanced) Three-Speed
473 Ethernet Controller found on Freescale SoCs.