1 // SPDX-License-Identifier: GPL-2.0+
3 * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
4 * Rohit Choraria <rohitkc@ti.com>
9 #include <linux/errno.h>
10 #include <asm/arch/mem.h>
11 #include <linux/mtd/omap_gpmc.h>
12 #include <linux/mtd/nand_ecc.h>
13 #include <linux/bch.h>
14 #include <linux/compiler.h>
16 #include <linux/mtd/omap_elm.h>
18 #define BADBLOCK_MARKER_LENGTH 2
19 #define SECTOR_BYTES 512
20 #define ECCCLEAR (0x1 << 8)
21 #define ECCRESULTREG1 (0x1 << 0)
22 /* 4 bit padding to make byte aligned, 56 = 52 + 4 */
23 #define BCH4_BIT_PAD 4
26 static u8 bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2,
27 0x97, 0x79, 0xe5, 0x24, 0xb5};
29 static uint8_t cs_next;
30 static __maybe_unused struct nand_ecclayout omap_ecclayout;
32 #if defined(CONFIG_NAND_OMAP_GPMC_WSCFG)
33 static const int8_t wscfg[CONFIG_SYS_MAX_NAND_DEVICE] =
34 { CONFIG_NAND_OMAP_GPMC_WSCFG };
36 /* wscfg is preset to zero since its a static variable */
37 static const int8_t wscfg[CONFIG_SYS_MAX_NAND_DEVICE];
41 * Driver configurations
43 struct omap_nand_info {
44 struct bch_control *control;
45 enum omap_ecc ecc_scheme;
47 uint8_t ws; /* wait status pin (0,1) */
50 /* We are wasting a bit of memory but al least we are safe */
51 static struct omap_nand_info omap_nand_info[GPMC_MAX_CS];
54 * omap_nand_hwcontrol - Set the address pointers corretly for the
55 * following address/data/command operation
57 static void omap_nand_hwcontrol(struct mtd_info *mtd, int32_t cmd,
60 register struct nand_chip *this = mtd_to_nand(mtd);
61 struct omap_nand_info *info = nand_get_controller_data(this);
65 * Point the IO_ADDR to DATA and ADDRESS registers instead
69 case NAND_CTRL_CHANGE | NAND_CTRL_CLE:
70 this->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd;
72 case NAND_CTRL_CHANGE | NAND_CTRL_ALE:
73 this->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_adr;
75 case NAND_CTRL_CHANGE | NAND_NCE:
76 this->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat;
80 if (cmd != NAND_CMD_NONE)
81 writeb(cmd, this->IO_ADDR_W);
84 /* Check wait pin as dev ready indicator */
85 static int omap_dev_ready(struct mtd_info *mtd)
87 register struct nand_chip *this = mtd_to_nand(mtd);
88 struct omap_nand_info *info = nand_get_controller_data(this);
89 return gpmc_cfg->status & (1 << (8 + info->ws));
93 * gen_true_ecc - This function will generate true ECC value, which
94 * can be used when correcting data read from NAND flash memory core
96 * @ecc_buf: buffer to store ecc code
98 * @return: re-formatted ECC value
100 static uint32_t gen_true_ecc(uint8_t *ecc_buf)
102 return ecc_buf[0] | (ecc_buf[1] << 16) | ((ecc_buf[2] & 0xF0) << 20) |
103 ((ecc_buf[2] & 0x0F) << 8);
107 * omap_correct_data - Compares the ecc read from nand spare area with ECC
108 * registers values and corrects one bit error if it has occurred
109 * Further details can be had from OMAP TRM and the following selected links:
110 * http://en.wikipedia.org/wiki/Hamming_code
111 * http://www.cs.utexas.edu/users/plaxton/c/337/05f/slides/ErrorCorrection-4.pdf
113 * @mtd: MTD device structure
115 * @read_ecc: ecc read from nand flash
116 * @calc_ecc: ecc read from ECC registers
118 * @return 0 if data is OK or corrected, else returns -1
120 static int __maybe_unused omap_correct_data(struct mtd_info *mtd, uint8_t *dat,
121 uint8_t *read_ecc, uint8_t *calc_ecc)
123 uint32_t orig_ecc, new_ecc, res, hm;
124 uint16_t parity_bits, byte;
127 /* Regenerate the orginal ECC */
128 orig_ecc = gen_true_ecc(read_ecc);
129 new_ecc = gen_true_ecc(calc_ecc);
130 /* Get the XOR of real ecc */
131 res = orig_ecc ^ new_ecc;
133 /* Get the hamming width */
135 /* Single bit errors can be corrected! */
137 /* Correctable data! */
138 parity_bits = res >> 16;
139 bit = (parity_bits & 0x7);
140 byte = (parity_bits >> 3) & 0x1FF;
141 /* Flip the bit to correct */
142 dat[byte] ^= (0x1 << bit);
143 } else if (hm == 1) {
144 printf("Error: Ecc is wrong\n");
145 /* ECC itself is corrupted */
149 * hm distance != parity pairs OR one, could mean 2 bit
150 * error OR potentially be on a blank page..
151 * orig_ecc: contains spare area data from nand flash.
152 * new_ecc: generated ecc while reading data area.
153 * Note: if the ecc = 0, all data bits from which it was
154 * generated are 0xFF.
155 * The 3 byte(24 bits) ecc is generated per 512byte
156 * chunk of a page. If orig_ecc(from spare area)
157 * is 0xFF && new_ecc(computed now from data area)=0x0,
158 * this means that data area is 0xFF and spare area is
159 * 0xFF. A sure sign of a erased page!
161 if ((orig_ecc == 0x0FFF0FFF) && (new_ecc == 0x00000000))
163 printf("Error: Bad compare! failed\n");
164 /* detected 2 bit error */
172 * omap_enable_hwecc - configures GPMC as per ECC scheme before read/write
173 * @mtd: MTD device structure
174 * @mode: Read/Write mode
177 static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
179 struct nand_chip *nand = mtd_to_nand(mtd);
180 struct omap_nand_info *info = nand_get_controller_data(nand);
181 unsigned int dev_width = (nand->options & NAND_BUSWIDTH_16) ? 1 : 0;
182 unsigned int ecc_algo = 0;
183 unsigned int bch_type = 0;
184 unsigned int eccsize1 = 0x00, eccsize0 = 0x00, bch_wrapmode = 0x00;
185 u32 ecc_size_config_val = 0;
186 u32 ecc_config_val = 0;
189 /* configure GPMC for specific ecc-scheme */
190 switch (info->ecc_scheme) {
191 case OMAP_ECC_HAM1_CODE_SW:
193 case OMAP_ECC_HAM1_CODE_HW:
200 case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
201 case OMAP_ECC_BCH8_CODE_HW:
204 if (mode == NAND_ECC_WRITE) {
206 eccsize0 = 0; /* extra bits in nibbles per sector */
207 eccsize1 = 28; /* OOB bits in nibbles per sector */
210 eccsize0 = 26; /* ECC bits in nibbles per sector */
211 eccsize1 = 2; /* non-ECC bits in nibbles per sector */
214 case OMAP_ECC_BCH16_CODE_HW:
217 if (mode == NAND_ECC_WRITE) {
219 eccsize0 = 0; /* extra bits in nibbles per sector */
220 eccsize1 = 52; /* OOB bits in nibbles per sector */
223 eccsize0 = 52; /* ECC bits in nibbles per sector */
224 eccsize1 = 0; /* non-ECC bits in nibbles per sector */
230 /* Clear ecc and enable bits */
231 writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
232 /* Configure ecc size for BCH */
233 ecc_size_config_val = (eccsize1 << 22) | (eccsize0 << 12);
234 writel(ecc_size_config_val, &gpmc_cfg->ecc_size_config);
236 /* Configure device details for BCH engine */
237 ecc_config_val = ((ecc_algo << 16) | /* HAM1 | BCHx */
238 (bch_type << 12) | /* BCH4/BCH8/BCH16 */
239 (bch_wrapmode << 8) | /* wrap mode */
240 (dev_width << 7) | /* bus width */
241 (0x0 << 4) | /* number of sectors */
242 (cs << 1) | /* ECC CS */
243 (0x1)); /* enable ECC */
244 writel(ecc_config_val, &gpmc_cfg->ecc_config);
248 * omap_calculate_ecc - Read ECC result
249 * @mtd: MTD structure
251 * @ecc_code: ecc_code buffer
252 * Using noninverted ECC can be considered ugly since writing a blank
253 * page ie. padding will clear the ECC bytes. This is no problem as
254 * long nobody is trying to write data on the seemingly unused page.
255 * Reading an erased page will produce an ECC mismatch between
256 * generated and read ECC bytes that has to be dealt with separately.
257 * E.g. if page is 0xFF (fresh erased), and if HW ECC engine within GPMC
258 * is used, the result of read will be 0x0 while the ECC offsets of the
259 * spare area will be 0xFF which will result in an ECC mismatch.
261 static int omap_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat,
264 struct nand_chip *chip = mtd_to_nand(mtd);
265 struct omap_nand_info *info = nand_get_controller_data(chip);
270 switch (info->ecc_scheme) {
271 case OMAP_ECC_HAM1_CODE_HW:
272 val = readl(&gpmc_cfg->ecc1_result);
273 ecc_code[0] = val & 0xFF;
274 ecc_code[1] = (val >> 16) & 0xFF;
275 ecc_code[2] = ((val >> 8) & 0x0F) | ((val >> 20) & 0xF0);
278 case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
280 case OMAP_ECC_BCH8_CODE_HW:
281 ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[3];
283 ecc_code[i++] = (val >> 0) & 0xFF;
285 for (j = 0; j < 3; j++) {
287 ecc_code[i++] = (val >> 24) & 0xFF;
288 ecc_code[i++] = (val >> 16) & 0xFF;
289 ecc_code[i++] = (val >> 8) & 0xFF;
290 ecc_code[i++] = (val >> 0) & 0xFF;
294 case OMAP_ECC_BCH16_CODE_HW:
295 val = readl(&gpmc_cfg->bch_result_4_6[0].bch_result_x[2]);
296 ecc_code[i++] = (val >> 8) & 0xFF;
297 ecc_code[i++] = (val >> 0) & 0xFF;
298 val = readl(&gpmc_cfg->bch_result_4_6[0].bch_result_x[1]);
299 ecc_code[i++] = (val >> 24) & 0xFF;
300 ecc_code[i++] = (val >> 16) & 0xFF;
301 ecc_code[i++] = (val >> 8) & 0xFF;
302 ecc_code[i++] = (val >> 0) & 0xFF;
303 val = readl(&gpmc_cfg->bch_result_4_6[0].bch_result_x[0]);
304 ecc_code[i++] = (val >> 24) & 0xFF;
305 ecc_code[i++] = (val >> 16) & 0xFF;
306 ecc_code[i++] = (val >> 8) & 0xFF;
307 ecc_code[i++] = (val >> 0) & 0xFF;
308 for (j = 3; j >= 0; j--) {
309 val = readl(&gpmc_cfg->bch_result_0_3[0].bch_result_x[j]
311 ecc_code[i++] = (val >> 24) & 0xFF;
312 ecc_code[i++] = (val >> 16) & 0xFF;
313 ecc_code[i++] = (val >> 8) & 0xFF;
314 ecc_code[i++] = (val >> 0) & 0xFF;
320 /* ECC scheme specific syndrome customizations */
321 switch (info->ecc_scheme) {
322 case OMAP_ECC_HAM1_CODE_HW:
325 case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
327 for (i = 0; i < chip->ecc.bytes; i++)
328 *(ecc_code + i) = *(ecc_code + i) ^
332 case OMAP_ECC_BCH8_CODE_HW:
333 ecc_code[chip->ecc.bytes - 1] = 0x00;
335 case OMAP_ECC_BCH16_CODE_HW:
343 #ifdef CONFIG_NAND_OMAP_GPMC_PREFETCH
345 #define PREFETCH_CONFIG1_CS_SHIFT 24
346 #define PREFETCH_FIFOTHRESHOLD_MAX 0x40
347 #define PREFETCH_FIFOTHRESHOLD(val) ((val) << 8)
348 #define PREFETCH_STATUS_COUNT(val) (val & 0x00003fff)
349 #define PREFETCH_STATUS_FIFO_CNT(val) ((val >> 24) & 0x7F)
350 #define ENABLE_PREFETCH (1 << 7)
353 * omap_prefetch_enable - configures and starts prefetch transfer
354 * @fifo_th: fifo threshold to be used for read/ write
355 * @count: number of bytes to be transferred
356 * @is_write: prefetch read(0) or write post(1) mode
357 * @cs: chip select to use
359 static int omap_prefetch_enable(int fifo_th, unsigned int count, int is_write, int cs)
363 if (fifo_th > PREFETCH_FIFOTHRESHOLD_MAX)
366 if (readl(&gpmc_cfg->prefetch_control))
369 /* Set the amount of bytes to be prefetched */
370 writel(count, &gpmc_cfg->prefetch_config2);
372 val = (cs << PREFETCH_CONFIG1_CS_SHIFT) | (is_write & 1) |
373 PREFETCH_FIFOTHRESHOLD(fifo_th) | ENABLE_PREFETCH;
374 writel(val, &gpmc_cfg->prefetch_config1);
376 /* Start the prefetch engine */
377 writel(1, &gpmc_cfg->prefetch_control);
383 * omap_prefetch_reset - disables and stops the prefetch engine
385 static void omap_prefetch_reset(void)
387 writel(0, &gpmc_cfg->prefetch_control);
388 writel(0, &gpmc_cfg->prefetch_config1);
391 static int __read_prefetch_aligned(struct nand_chip *chip, uint32_t *buf, int len)
395 struct omap_nand_info *info = nand_get_controller_data(chip);
397 ret = omap_prefetch_enable(PREFETCH_FIFOTHRESHOLD_MAX, len, 0, info->cs);
404 cnt = readl(&gpmc_cfg->prefetch_status);
405 cnt = PREFETCH_STATUS_FIFO_CNT(cnt);
407 for (i = 0; i < cnt / 4; i++) {
408 *buf++ = readl(CONFIG_SYS_NAND_BASE);
413 omap_prefetch_reset();
418 static inline void omap_nand_read(struct mtd_info *mtd, uint8_t *buf, int len)
420 struct nand_chip *chip = mtd_to_nand(mtd);
422 if (chip->options & NAND_BUSWIDTH_16)
423 nand_read_buf16(mtd, buf, len);
425 nand_read_buf(mtd, buf, len);
428 static void omap_nand_read_prefetch(struct mtd_info *mtd, uint8_t *buf, int len)
432 struct nand_chip *chip = mtd_to_nand(mtd);
435 * If the destination buffer is unaligned, start with reading
436 * the overlap byte-wise.
438 head = ((uint32_t) buf) % 4;
440 omap_nand_read(mtd, buf, head);
446 * Only transfer multiples of 4 bytes in a pre-fetched fashion.
447 * If there's a residue, care for it byte-wise afterwards.
451 ret = __read_prefetch_aligned(chip, (uint32_t *)buf, len - tail);
453 /* fallback in case the prefetch engine is busy */
454 omap_nand_read(mtd, buf, len);
457 omap_nand_read(mtd, buf, tail);
460 #endif /* CONFIG_NAND_OMAP_GPMC_PREFETCH */
462 #ifdef CONFIG_NAND_OMAP_ELM
464 * omap_reverse_list - re-orders list elements in reverse order [internal]
465 * @list: pointer to start of list
466 * @length: length of list
468 static void omap_reverse_list(u8 *list, unsigned int length)
471 unsigned int half_length = length / 2;
473 for (i = 0, j = length - 1; i < half_length; i++, j--) {
481 * omap_correct_data_bch - Compares the ecc read from nand spare area
482 * with ECC registers values and corrects one bit error if it has occurred
484 * @mtd: MTD device structure
486 * @read_ecc: ecc read from nand flash (ignored)
487 * @calc_ecc: ecc read from ECC registers
489 * @return 0 if data is OK or corrected, else returns -1
491 static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
492 uint8_t *read_ecc, uint8_t *calc_ecc)
494 struct nand_chip *chip = mtd_to_nand(mtd);
495 struct omap_nand_info *info = nand_get_controller_data(chip);
496 struct nand_ecc_ctrl *ecc = &chip->ecc;
497 uint32_t error_count = 0, error_max;
498 uint32_t error_loc[ELM_MAX_ERROR_COUNT];
499 enum bch_level bch_type;
500 uint32_t i, ecc_flag = 0;
502 uint32_t byte_pos, bit_pos;
505 /* check calculated ecc */
506 for (i = 0; i < ecc->bytes && !ecc_flag; i++) {
507 if (calc_ecc[i] != 0x00)
513 /* check for whether its a erased-page */
515 for (i = 0; i < ecc->bytes && !ecc_flag; i++) {
516 if (read_ecc[i] != 0xff)
523 * while reading ECC result we read it in big endian.
524 * Hence while loading to ELM we have rotate to get the right endian.
526 switch (info->ecc_scheme) {
527 case OMAP_ECC_BCH8_CODE_HW:
528 bch_type = BCH_8_BIT;
529 omap_reverse_list(calc_ecc, ecc->bytes - 1);
531 case OMAP_ECC_BCH16_CODE_HW:
532 bch_type = BCH_16_BIT;
533 omap_reverse_list(calc_ecc, ecc->bytes);
538 /* use elm module to check for errors */
539 elm_config(bch_type);
540 err = elm_check_error(calc_ecc, bch_type, &error_count, error_loc);
544 /* correct bch error */
545 for (count = 0; count < error_count; count++) {
546 switch (info->ecc_scheme) {
547 case OMAP_ECC_BCH8_CODE_HW:
548 /* 14th byte in ECC is reserved to match ROM layout */
549 error_max = SECTOR_BYTES + (ecc->bytes - 1);
551 case OMAP_ECC_BCH16_CODE_HW:
552 error_max = SECTOR_BYTES + ecc->bytes;
557 byte_pos = error_max - (error_loc[count] / 8) - 1;
558 bit_pos = error_loc[count] % 8;
559 if (byte_pos < SECTOR_BYTES) {
560 dat[byte_pos] ^= 1 << bit_pos;
561 debug("nand: bit-flip corrected @data=%d\n", byte_pos);
562 } else if (byte_pos < error_max) {
563 read_ecc[byte_pos - SECTOR_BYTES] ^= 1 << bit_pos;
564 debug("nand: bit-flip corrected @oob=%d\n", byte_pos -
568 printf("nand: error: invalid bit-flip location\n");
571 return (err) ? err : error_count;
575 * omap_read_page_bch - hardware ecc based page read function
576 * @mtd: mtd info structure
577 * @chip: nand chip info structure
578 * @buf: buffer to store read data
579 * @oob_required: caller expects OOB data read to chip->oob_poi
580 * @page: page number to read
583 static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
584 uint8_t *buf, int oob_required, int page)
586 int i, eccsize = chip->ecc.size;
587 int eccbytes = chip->ecc.bytes;
588 int eccsteps = chip->ecc.steps;
590 uint8_t *ecc_calc = chip->buffers->ecccalc;
591 uint8_t *ecc_code = chip->buffers->ecccode;
592 uint32_t *eccpos = chip->ecc.layout->eccpos;
593 uint8_t *oob = chip->oob_poi;
599 oob_pos = (eccsize * eccsteps) + chip->ecc.layout->eccpos[0];
600 oob += chip->ecc.layout->eccpos[0];
602 for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize,
604 chip->ecc.hwctl(mtd, NAND_ECC_READ);
606 chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_pos, -1);
607 chip->read_buf(mtd, p, eccsize);
609 /* read respective ecc from oob area */
610 chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, -1);
611 chip->read_buf(mtd, oob, eccbytes);
613 chip->ecc.calculate(mtd, p, &ecc_calc[i]);
619 for (i = 0; i < chip->ecc.total; i++)
620 ecc_code[i] = chip->oob_poi[eccpos[i]];
622 eccsteps = chip->ecc.steps;
625 for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
628 stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
630 mtd->ecc_stats.failed++;
632 mtd->ecc_stats.corrected += stat;
636 #endif /* CONFIG_NAND_OMAP_ELM */
639 * OMAP3 BCH8 support (with BCH library)
643 * omap_correct_data_bch_sw - Decode received data and correct errors
644 * @mtd: MTD device structure
646 * @read_ecc: ecc read from nand flash
647 * @calc_ecc: ecc read from HW ECC registers
649 static int omap_correct_data_bch_sw(struct mtd_info *mtd, u_char *data,
650 u_char *read_ecc, u_char *calc_ecc)
653 /* cannot correct more than 8 errors */
654 unsigned int errloc[8];
655 struct nand_chip *chip = mtd_to_nand(mtd);
656 struct omap_nand_info *info = nand_get_controller_data(chip);
658 count = decode_bch(info->control, NULL, SECTOR_BYTES,
659 read_ecc, calc_ecc, NULL, errloc);
662 for (i = 0; i < count; i++) {
663 /* correct data only, not ecc bytes */
664 if (errloc[i] < SECTOR_BYTES << 3)
665 data[errloc[i] >> 3] ^= 1 << (errloc[i] & 7);
666 debug("corrected bitflip %u\n", errloc[i]);
670 * BCH8 have 13 bytes of ECC; BCH4 needs adoption
673 for (i = 0; i < 13; i++)
674 printf("%02x ", read_ecc[i]);
677 for (i = 0; i < 13; i++)
678 printf("%02x ", calc_ecc[i]);
682 } else if (count < 0) {
683 puts("ecc unrecoverable error\n");
689 * omap_free_bch - Release BCH ecc resources
690 * @mtd: MTD device structure
692 static void __maybe_unused omap_free_bch(struct mtd_info *mtd)
694 struct nand_chip *chip = mtd_to_nand(mtd);
695 struct omap_nand_info *info = nand_get_controller_data(chip);
698 free_bch(info->control);
699 info->control = NULL;
702 #endif /* CONFIG_BCH */
705 * omap_select_ecc_scheme - configures driver for particular ecc-scheme
706 * @nand: NAND chip device structure
707 * @ecc_scheme: ecc scheme to configure
708 * @pagesize: number of main-area bytes per page of NAND device
709 * @oobsize: number of OOB/spare bytes per page of NAND device
711 static int omap_select_ecc_scheme(struct nand_chip *nand,
712 enum omap_ecc ecc_scheme, unsigned int pagesize, unsigned int oobsize) {
713 struct omap_nand_info *info = nand_get_controller_data(nand);
714 struct nand_ecclayout *ecclayout = &omap_ecclayout;
715 int eccsteps = pagesize / SECTOR_BYTES;
718 switch (ecc_scheme) {
719 case OMAP_ECC_HAM1_CODE_SW:
720 debug("nand: selected OMAP_ECC_HAM1_CODE_SW\n");
721 /* For this ecc-scheme, ecc.bytes, ecc.layout, ... are
722 * initialized in nand_scan_tail(), so just set ecc.mode */
723 info->control = NULL;
724 nand->ecc.mode = NAND_ECC_SOFT;
725 nand->ecc.layout = NULL;
729 case OMAP_ECC_HAM1_CODE_HW:
730 debug("nand: selected OMAP_ECC_HAM1_CODE_HW\n");
731 /* check ecc-scheme requirements before updating ecc info */
732 if ((3 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
733 printf("nand: error: insufficient OOB: require=%d\n", (
734 (3 * eccsteps) + BADBLOCK_MARKER_LENGTH));
737 info->control = NULL;
738 /* populate ecc specific fields */
739 memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
740 nand->ecc.mode = NAND_ECC_HW;
741 nand->ecc.strength = 1;
742 nand->ecc.size = SECTOR_BYTES;
744 nand->ecc.hwctl = omap_enable_hwecc;
745 nand->ecc.correct = omap_correct_data;
746 nand->ecc.calculate = omap_calculate_ecc;
747 /* define ecc-layout */
748 ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
749 for (i = 0; i < ecclayout->eccbytes; i++) {
750 if (nand->options & NAND_BUSWIDTH_16)
751 ecclayout->eccpos[i] = i + 2;
753 ecclayout->eccpos[i] = i + 1;
755 ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
756 ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
757 BADBLOCK_MARKER_LENGTH;
760 case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
762 debug("nand: selected OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n");
763 /* check ecc-scheme requirements before updating ecc info */
764 if ((13 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
765 printf("nand: error: insufficient OOB: require=%d\n", (
766 (13 * eccsteps) + BADBLOCK_MARKER_LENGTH));
769 /* check if BCH S/W library can be used for error detection */
770 info->control = init_bch(13, 8, 0x201b);
771 if (!info->control) {
772 printf("nand: error: could not init_bch()\n");
775 /* populate ecc specific fields */
776 memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
777 nand->ecc.mode = NAND_ECC_HW;
778 nand->ecc.strength = 8;
779 nand->ecc.size = SECTOR_BYTES;
780 nand->ecc.bytes = 13;
781 nand->ecc.hwctl = omap_enable_hwecc;
782 nand->ecc.correct = omap_correct_data_bch_sw;
783 nand->ecc.calculate = omap_calculate_ecc;
784 /* define ecc-layout */
785 ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
786 ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
787 for (i = 1; i < ecclayout->eccbytes; i++) {
788 if (i % nand->ecc.bytes)
789 ecclayout->eccpos[i] =
790 ecclayout->eccpos[i - 1] + 1;
792 ecclayout->eccpos[i] =
793 ecclayout->eccpos[i - 1] + 2;
795 ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
796 ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
797 BADBLOCK_MARKER_LENGTH;
800 printf("nand: error: CONFIG_BCH required for ECC\n");
804 case OMAP_ECC_BCH8_CODE_HW:
805 #ifdef CONFIG_NAND_OMAP_ELM
806 debug("nand: selected OMAP_ECC_BCH8_CODE_HW\n");
807 /* check ecc-scheme requirements before updating ecc info */
808 if ((14 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
809 printf("nand: error: insufficient OOB: require=%d\n", (
810 (14 * eccsteps) + BADBLOCK_MARKER_LENGTH));
813 /* intialize ELM for ECC error detection */
815 info->control = NULL;
816 /* populate ecc specific fields */
817 memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl));
818 nand->ecc.mode = NAND_ECC_HW;
819 nand->ecc.strength = 8;
820 nand->ecc.size = SECTOR_BYTES;
821 nand->ecc.bytes = 14;
822 nand->ecc.hwctl = omap_enable_hwecc;
823 nand->ecc.correct = omap_correct_data_bch;
824 nand->ecc.calculate = omap_calculate_ecc;
825 nand->ecc.read_page = omap_read_page_bch;
826 /* define ecc-layout */
827 ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
828 for (i = 0; i < ecclayout->eccbytes; i++)
829 ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH;
830 ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
831 ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
832 BADBLOCK_MARKER_LENGTH;
835 printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n");
839 case OMAP_ECC_BCH16_CODE_HW:
840 #ifdef CONFIG_NAND_OMAP_ELM
841 debug("nand: using OMAP_ECC_BCH16_CODE_HW\n");
842 /* check ecc-scheme requirements before updating ecc info */
843 if ((26 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
844 printf("nand: error: insufficient OOB: require=%d\n", (
845 (26 * eccsteps) + BADBLOCK_MARKER_LENGTH));
848 /* intialize ELM for ECC error detection */
850 /* populate ecc specific fields */
851 nand->ecc.mode = NAND_ECC_HW;
852 nand->ecc.size = SECTOR_BYTES;
853 nand->ecc.bytes = 26;
854 nand->ecc.strength = 16;
855 nand->ecc.hwctl = omap_enable_hwecc;
856 nand->ecc.correct = omap_correct_data_bch;
857 nand->ecc.calculate = omap_calculate_ecc;
858 nand->ecc.read_page = omap_read_page_bch;
859 /* define ecc-layout */
860 ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
861 for (i = 0; i < ecclayout->eccbytes; i++)
862 ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH;
863 ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
864 ecclayout->oobfree[0].length = oobsize - nand->ecc.bytes -
865 BADBLOCK_MARKER_LENGTH;
868 printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n");
872 debug("nand: error: ecc scheme not enabled or supported\n");
876 /* nand_scan_tail() sets ham1 sw ecc; hw ecc layout is set by driver */
877 if (ecc_scheme != OMAP_ECC_HAM1_CODE_SW)
878 nand->ecc.layout = ecclayout;
880 info->ecc_scheme = ecc_scheme;
884 #ifndef CONFIG_SPL_BUILD
886 * omap_nand_switch_ecc - switch the ECC operation between different engines
887 * (h/w and s/w) and different algorithms (hamming and BCHx)
889 * @hardware - true if one of the HW engines should be used
890 * @eccstrength - the number of bits that could be corrected
891 * (1 - hamming, 4 - BCH4, 8 - BCH8, 16 - BCH16)
893 int __maybe_unused omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength)
895 struct nand_chip *nand;
896 struct mtd_info *mtd = get_nand_dev_by_index(nand_curr_device);
900 printf("nand: error: no NAND devices found\n");
904 nand = mtd_to_nand(mtd);
905 nand->options |= NAND_OWN_BUFFERS;
906 nand->options &= ~NAND_SUBPAGE_READ;
907 /* Setup the ecc configurations again */
909 if (eccstrength == 1) {
910 err = omap_select_ecc_scheme(nand,
911 OMAP_ECC_HAM1_CODE_HW,
912 mtd->writesize, mtd->oobsize);
913 } else if (eccstrength == 8) {
914 err = omap_select_ecc_scheme(nand,
915 OMAP_ECC_BCH8_CODE_HW,
916 mtd->writesize, mtd->oobsize);
917 } else if (eccstrength == 16) {
918 err = omap_select_ecc_scheme(nand,
919 OMAP_ECC_BCH16_CODE_HW,
920 mtd->writesize, mtd->oobsize);
922 printf("nand: error: unsupported ECC scheme\n");
926 if (eccstrength == 1) {
927 err = omap_select_ecc_scheme(nand,
928 OMAP_ECC_HAM1_CODE_SW,
929 mtd->writesize, mtd->oobsize);
930 } else if (eccstrength == 8) {
931 err = omap_select_ecc_scheme(nand,
932 OMAP_ECC_BCH8_CODE_HW_DETECTION_SW,
933 mtd->writesize, mtd->oobsize);
935 printf("nand: error: unsupported ECC scheme\n");
940 /* Update NAND handling after ECC mode switch */
942 err = nand_scan_tail(mtd);
945 #endif /* CONFIG_SPL_BUILD */
948 * Board-specific NAND initialization. The following members of the
949 * argument are board-specific:
950 * - IO_ADDR_R: address to read the 8 I/O lines of the flash device
951 * - IO_ADDR_W: address to write the 8 I/O lines of the flash device
952 * - cmd_ctrl: hardwarespecific function for accesing control-lines
953 * - waitfunc: hardwarespecific function for accesing device ready/busy line
954 * - ecc.hwctl: function to enable (reset) hardware ecc generator
955 * - ecc.mode: mode of ecc, see defines
956 * - chip_delay: chip dependent delay for transfering data from array to
958 * - options: various chip options. They can partly be set to inform
959 * nand_scan about special functionality. See the defines for further
962 int board_nand_init(struct nand_chip *nand)
964 int32_t gpmc_config = 0;
968 * xloader/Uboot's gpmc configuration would have configured GPMC for
969 * nand type of memory. The following logic scans and latches on to the
970 * first CS with NAND type memory.
971 * TBD: need to make this logic generic to handle multiple CS NAND
974 while (cs < GPMC_MAX_CS) {
975 /* Check if NAND type is set */
976 if ((readl(&gpmc_cfg->cs[cs].config1) & 0xC00) == 0x800) {
982 if (cs >= GPMC_MAX_CS) {
983 printf("nand: error: Unable to find NAND settings in "
984 "GPMC Configuration - quitting\n");
988 gpmc_config = readl(&gpmc_cfg->config);
989 /* Disable Write protect */
991 writel(gpmc_config, &gpmc_cfg->config);
993 nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat;
994 nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd;
995 omap_nand_info[cs].control = NULL;
996 omap_nand_info[cs].cs = cs;
997 omap_nand_info[cs].ws = wscfg[cs];
998 nand_set_controller_data(nand, &omap_nand_info[cs]);
999 nand->cmd_ctrl = omap_nand_hwcontrol;
1000 nand->options |= NAND_NO_PADDING | NAND_CACHEPRG;
1001 nand->chip_delay = 100;
1002 nand->ecc.layout = &omap_ecclayout;
1004 /* configure driver and controller based on NAND device bus-width */
1005 gpmc_config = readl(&gpmc_cfg->cs[cs].config1);
1006 #if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT)
1007 nand->options |= NAND_BUSWIDTH_16;
1008 writel(gpmc_config | (0x1 << 12), &gpmc_cfg->cs[cs].config1);
1010 nand->options &= ~NAND_BUSWIDTH_16;
1011 writel(gpmc_config & ~(0x1 << 12), &gpmc_cfg->cs[cs].config1);
1013 /* select ECC scheme */
1014 #if defined(CONFIG_NAND_OMAP_ECCSCHEME)
1015 err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME,
1016 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE);
1018 /* pagesize and oobsize are not required to configure sw ecc-scheme */
1019 err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW,
1025 #ifdef CONFIG_NAND_OMAP_GPMC_PREFETCH
1026 nand->read_buf = omap_nand_read_prefetch;
1028 if (nand->options & NAND_BUSWIDTH_16)
1029 nand->read_buf = nand_read_buf16;
1031 nand->read_buf = nand_read_buf;
1034 nand->dev_ready = omap_dev_ready;