3 * KwikByte <kb9200_dev@kwikbyte.com>
6 * Matthias Kaehlcke <matthias@kaehlcke.net>
8 * SPDX-License-Identifier: GPL-2.0+
13 #include <asm/arch/AT91RM9200.h>
14 #include <asm/arch/hardware.h>
19 * hardware specific access to control-lines
22 #define MASK_ALE (1 << 22) /* our ALE is A22 */
23 #define MASK_CLE (1 << 21) /* our CLE is A21 */
25 #define KB9202_NAND_NCE (1 << 28) /* EN* on D28 */
26 #define KB9202_NAND_BUSY (1 << 29) /* RB* on D29 */
28 #define KB9202_SMC2_NWS (1 << 2)
29 #define KB9202_SMC2_TDF (1 << 8)
30 #define KB9202_SMC2_RWSETUP (1 << 24)
31 #define KB9202_SMC2_RWHOLD (1 << 29)
34 * Board-specific function to access device control signals
36 static void kb9202_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
38 struct nand_chip *this = mtd->priv;
40 if (ctrl & NAND_CTRL_CHANGE) {
41 ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
43 /* clear ALE and CLE bits */
44 IO_ADDR_W &= ~(MASK_ALE | MASK_CLE);
47 IO_ADDR_W |= MASK_CLE;
50 IO_ADDR_W |= MASK_ALE;
52 this->IO_ADDR_W = (void *) IO_ADDR_W;
55 writel(KB9202_NAND_NCE, AT91C_PIOC_CODR);
57 writel(KB9202_NAND_NCE, AT91C_PIOC_SODR);
60 if (cmd != NAND_CMD_NONE)
61 writeb(cmd, this->IO_ADDR_W);
66 * Board-specific function to access the device ready signal.
68 static int kb9202_nand_ready(struct mtd_info *mtd)
70 return readl(AT91C_PIOC_PDSR) & KB9202_NAND_BUSY;
75 * Board-specific NAND init. Copied from include/linux/mtd/nand.h for reference.
77 * struct nand_chip - NAND Private Flash Chip Data
78 * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device
79 * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device
80 * @hwcontrol: [BOARDSPECIFIC] hardwarespecific function for accesing control-lines
81 * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line
82 * If set to NULL no access to ready/busy is available and the ready/busy information
83 * is read from the chip status register
84 * @enable_hwecc: [BOARDSPECIFIC] function to enable (reset) hardware ecc generator. Must only
85 * be provided if a hardware ECC is available
86 * @eccmode: [BOARDSPECIFIC] mode of ecc, see defines
87 * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR)
88 * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about
89 * special functionality. See the defines for further explanation
92 * This routine initializes controller and GPIOs.
94 int board_nand_init(struct nand_chip *nand)
98 nand->ecc.mode = NAND_ECC_SOFT;
99 nand->cmd_ctrl = kb9202_nand_hwcontrol;
100 nand->dev_ready = kb9202_nand_ready;
102 /* in case running outside of bootloader */
103 writel(1 << AT91C_ID_PIOC, AT91C_PMC_PCER);
105 /* setup nand flash access (allow ample margin) */
106 /* 4 wait states, 1 setup, 1 hold, 1 float for 8-bit device */
107 writel(AT91C_SMC2_WSEN | KB9202_SMC2_NWS | KB9202_SMC2_TDF |
108 AT91C_SMC2_DBW_8 | KB9202_SMC2_RWSETUP | KB9202_SMC2_RWHOLD,
111 /* enable internal NAND controller */
112 value = readl(AT91C_EBI_CSA);
113 value |= AT91C_EBI_CS3A_SMC_SmartMedia;
114 writel(value, AT91C_EBI_CSA);
116 /* enable SMOE/SMWE */
117 writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_ASR);
118 writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_PDR);
119 writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_OER);
121 /* set NCE to high */
122 writel(KB9202_NAND_NCE, AT91C_PIOC_SODR);
124 /* disable output on pin connected to the busy line of the NAND */
125 writel(KB9202_NAND_BUSY, AT91C_PIOC_ODR);
127 /* enable the PIO to control NCE and BUSY */
128 writel(KB9202_NAND_NCE | KB9202_NAND_BUSY, AT91C_PIOC_PER);
130 /* enable output for NCE */
131 writel(KB9202_NAND_NCE, AT91C_PIOC_OER);