cmd: Add test and fix bugs for dm drivers
[oweals/u-boot.git] / drivers / mmc / sunxi_mmc.c
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * (C) Copyright 2007-2011
4  * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
5  * Aaron <leafy.myeh@allwinnertech.com>
6  *
7  * MMC driver for allwinner sunxi platform.
8  */
9
10 #include <common.h>
11 #include <dm.h>
12 #include <errno.h>
13 #include <malloc.h>
14 #include <mmc.h>
15 #include <clk.h>
16 #include <reset.h>
17 #include <asm/io.h>
18 #include <asm/arch/clock.h>
19 #include <asm/arch/cpu.h>
20 #include <asm/arch/gpio.h>
21 #include <asm/arch/mmc.h>
22 #include <asm-generic/gpio.h>
23
24 #ifdef CONFIG_DM_MMC
25 struct sunxi_mmc_variant {
26         u16 mclk_offset;
27 };
28 #endif
29
30 struct sunxi_mmc_plat {
31         struct mmc_config cfg;
32         struct mmc mmc;
33 };
34
35 struct sunxi_mmc_priv {
36         unsigned mmc_no;
37         uint32_t *mclkreg;
38         unsigned fatal_err;
39         struct gpio_desc cd_gpio;       /* Change Detect GPIO */
40         int cd_inverted;                /* Inverted Card Detect */
41         struct sunxi_mmc *reg;
42         struct mmc_config cfg;
43 #ifdef CONFIG_DM_MMC
44         const struct sunxi_mmc_variant *variant;
45 #endif
46 };
47
48 #if !CONFIG_IS_ENABLED(DM_MMC)
49 /* support 4 mmc hosts */
50 struct sunxi_mmc_priv mmc_host[4];
51
52 static int sunxi_mmc_getcd_gpio(int sdc_no)
53 {
54         switch (sdc_no) {
55         case 0: return sunxi_name_to_gpio(CONFIG_MMC0_CD_PIN);
56         case 1: return sunxi_name_to_gpio(CONFIG_MMC1_CD_PIN);
57         case 2: return sunxi_name_to_gpio(CONFIG_MMC2_CD_PIN);
58         case 3: return sunxi_name_to_gpio(CONFIG_MMC3_CD_PIN);
59         }
60         return -EINVAL;
61 }
62
63 static int mmc_resource_init(int sdc_no)
64 {
65         struct sunxi_mmc_priv *priv = &mmc_host[sdc_no];
66         struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
67         int cd_pin, ret = 0;
68
69         debug("init mmc %d resource\n", sdc_no);
70
71         switch (sdc_no) {
72         case 0:
73                 priv->reg = (struct sunxi_mmc *)SUNXI_MMC0_BASE;
74                 priv->mclkreg = &ccm->sd0_clk_cfg;
75                 break;
76         case 1:
77                 priv->reg = (struct sunxi_mmc *)SUNXI_MMC1_BASE;
78                 priv->mclkreg = &ccm->sd1_clk_cfg;
79                 break;
80         case 2:
81                 priv->reg = (struct sunxi_mmc *)SUNXI_MMC2_BASE;
82                 priv->mclkreg = &ccm->sd2_clk_cfg;
83                 break;
84 #ifdef SUNXI_MMC3_BASE
85         case 3:
86                 priv->reg = (struct sunxi_mmc *)SUNXI_MMC3_BASE;
87                 priv->mclkreg = &ccm->sd3_clk_cfg;
88                 break;
89 #endif
90         default:
91                 printf("Wrong mmc number %d\n", sdc_no);
92                 return -1;
93         }
94         priv->mmc_no = sdc_no;
95
96         cd_pin = sunxi_mmc_getcd_gpio(sdc_no);
97         if (cd_pin >= 0) {
98                 ret = gpio_request(cd_pin, "mmc_cd");
99                 if (!ret) {
100                         sunxi_gpio_set_pull(cd_pin, SUNXI_GPIO_PULL_UP);
101                         ret = gpio_direction_input(cd_pin);
102                 }
103         }
104
105         return ret;
106 }
107 #endif
108
109 static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz)
110 {
111         unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly;
112         bool new_mode = true;
113         bool calibrate = false;
114         u32 val = 0;
115
116         if (!IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE))
117                 new_mode = false;
118
119         /* A83T support new mode only on eMMC */
120         if (IS_ENABLED(CONFIG_MACH_SUN8I_A83T) && priv->mmc_no != 2)
121                 new_mode = false;
122
123 #if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
124         calibrate = true;
125 #endif
126
127         if (hz <= 24000000) {
128                 pll = CCM_MMC_CTRL_OSCM24;
129                 pll_hz = 24000000;
130         } else {
131 #ifdef CONFIG_MACH_SUN9I
132                 pll = CCM_MMC_CTRL_PLL_PERIPH0;
133                 pll_hz = clock_get_pll4_periph0();
134 #elif defined(CONFIG_MACH_SUN50I_H6)
135                 pll = CCM_MMC_CTRL_PLL6X2;
136                 pll_hz = clock_get_pll6() * 2;
137 #else
138                 pll = CCM_MMC_CTRL_PLL6;
139                 pll_hz = clock_get_pll6();
140 #endif
141         }
142
143         div = pll_hz / hz;
144         if (pll_hz % hz)
145                 div++;
146
147         n = 0;
148         while (div > 16) {
149                 n++;
150                 div = (div + 1) / 2;
151         }
152
153         if (n > 3) {
154                 printf("mmc %u error cannot set clock to %u\n", priv->mmc_no,
155                        hz);
156                 return -1;
157         }
158
159         /* determine delays */
160         if (hz <= 400000) {
161                 oclk_dly = 0;
162                 sclk_dly = 0;
163         } else if (hz <= 25000000) {
164                 oclk_dly = 0;
165                 sclk_dly = 5;
166 #ifdef CONFIG_MACH_SUN9I
167         } else if (hz <= 52000000) {
168                 oclk_dly = 5;
169                 sclk_dly = 4;
170         } else {
171                 /* hz > 52000000 */
172                 oclk_dly = 2;
173                 sclk_dly = 4;
174 #else
175         } else if (hz <= 52000000) {
176                 oclk_dly = 3;
177                 sclk_dly = 4;
178         } else {
179                 /* hz > 52000000 */
180                 oclk_dly = 1;
181                 sclk_dly = 4;
182 #endif
183         }
184
185         if (new_mode) {
186 #ifdef CONFIG_MMC_SUNXI_HAS_NEW_MODE
187 #ifdef CONFIG_MMC_SUNXI_HAS_MODE_SWITCH
188                 val = CCM_MMC_CTRL_MODE_SEL_NEW;
189 #endif
190                 setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW);
191 #endif
192         } else if (!calibrate) {
193                 /*
194                  * Use hardcoded delay values if controller doesn't support
195                  * calibration
196                  */
197                 val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) |
198                         CCM_MMC_CTRL_SCLK_DLY(sclk_dly);
199         }
200
201         writel(CCM_MMC_CTRL_ENABLE| pll | CCM_MMC_CTRL_N(n) |
202                CCM_MMC_CTRL_M(div) | val, priv->mclkreg);
203
204         debug("mmc %u set mod-clk req %u parent %u n %u m %u rate %u\n",
205               priv->mmc_no, hz, pll_hz, 1u << n, div, pll_hz / (1u << n) / div);
206
207         return 0;
208 }
209
210 static int mmc_update_clk(struct sunxi_mmc_priv *priv)
211 {
212         unsigned int cmd;
213         unsigned timeout_msecs = 2000;
214         unsigned long start = get_timer(0);
215
216         cmd = SUNXI_MMC_CMD_START |
217               SUNXI_MMC_CMD_UPCLK_ONLY |
218               SUNXI_MMC_CMD_WAIT_PRE_OVER;
219
220         writel(cmd, &priv->reg->cmd);
221         while (readl(&priv->reg->cmd) & SUNXI_MMC_CMD_START) {
222                 if (get_timer(start) > timeout_msecs)
223                         return -1;
224         }
225
226         /* clock update sets various irq status bits, clear these */
227         writel(readl(&priv->reg->rint), &priv->reg->rint);
228
229         return 0;
230 }
231
232 static int mmc_config_clock(struct sunxi_mmc_priv *priv, struct mmc *mmc)
233 {
234         unsigned rval = readl(&priv->reg->clkcr);
235
236         /* Disable Clock */
237         rval &= ~SUNXI_MMC_CLK_ENABLE;
238         writel(rval, &priv->reg->clkcr);
239         if (mmc_update_clk(priv))
240                 return -1;
241
242         /* Set mod_clk to new rate */
243         if (mmc_set_mod_clk(priv, mmc->clock))
244                 return -1;
245
246         /* Clear internal divider */
247         rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK;
248         writel(rval, &priv->reg->clkcr);
249
250 #if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
251         /* A64 supports calibration of delays on MMC controller and we
252          * have to set delay of zero before starting calibration.
253          * Allwinner BSP driver sets a delay only in the case of
254          * using HS400 which is not supported by mainline U-Boot or
255          * Linux at the moment
256          */
257         writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl);
258 #endif
259
260         /* Re-enable Clock */
261         rval |= SUNXI_MMC_CLK_ENABLE;
262         writel(rval, &priv->reg->clkcr);
263         if (mmc_update_clk(priv))
264                 return -1;
265
266         return 0;
267 }
268
269 static int sunxi_mmc_set_ios_common(struct sunxi_mmc_priv *priv,
270                                     struct mmc *mmc)
271 {
272         debug("set ios: bus_width: %x, clock: %d\n",
273               mmc->bus_width, mmc->clock);
274
275         /* Change clock first */
276         if (mmc->clock && mmc_config_clock(priv, mmc) != 0) {
277                 priv->fatal_err = 1;
278                 return -EINVAL;
279         }
280
281         /* Change bus width */
282         if (mmc->bus_width == 8)
283                 writel(0x2, &priv->reg->width);
284         else if (mmc->bus_width == 4)
285                 writel(0x1, &priv->reg->width);
286         else
287                 writel(0x0, &priv->reg->width);
288
289         return 0;
290 }
291
292 #if !CONFIG_IS_ENABLED(DM_MMC)
293 static int sunxi_mmc_core_init(struct mmc *mmc)
294 {
295         struct sunxi_mmc_priv *priv = mmc->priv;
296
297         /* Reset controller */
298         writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl);
299         udelay(1000);
300
301         return 0;
302 }
303 #endif
304
305 static int mmc_trans_data_by_cpu(struct sunxi_mmc_priv *priv, struct mmc *mmc,
306                                  struct mmc_data *data)
307 {
308         const int reading = !!(data->flags & MMC_DATA_READ);
309         const uint32_t status_bit = reading ? SUNXI_MMC_STATUS_FIFO_EMPTY :
310                                               SUNXI_MMC_STATUS_FIFO_FULL;
311         unsigned i;
312         unsigned *buff = (unsigned int *)(reading ? data->dest : data->src);
313         unsigned byte_cnt = data->blocksize * data->blocks;
314         unsigned timeout_msecs = byte_cnt >> 8;
315         unsigned long  start;
316
317         if (timeout_msecs < 2000)
318                 timeout_msecs = 2000;
319
320         /* Always read / write data through the CPU */
321         setbits_le32(&priv->reg->gctrl, SUNXI_MMC_GCTRL_ACCESS_BY_AHB);
322
323         start = get_timer(0);
324
325         for (i = 0; i < (byte_cnt >> 2); i++) {
326                 while (readl(&priv->reg->status) & status_bit) {
327                         if (get_timer(start) > timeout_msecs)
328                                 return -1;
329                 }
330
331                 if (reading)
332                         buff[i] = readl(&priv->reg->fifo);
333                 else
334                         writel(buff[i], &priv->reg->fifo);
335         }
336
337         return 0;
338 }
339
340 static int mmc_rint_wait(struct sunxi_mmc_priv *priv, struct mmc *mmc,
341                          uint timeout_msecs, uint done_bit, const char *what)
342 {
343         unsigned int status;
344         unsigned long start = get_timer(0);
345
346         do {
347                 status = readl(&priv->reg->rint);
348                 if ((get_timer(start) > timeout_msecs) ||
349                     (status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT)) {
350                         debug("%s timeout %x\n", what,
351                               status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT);
352                         return -ETIMEDOUT;
353                 }
354         } while (!(status & done_bit));
355
356         return 0;
357 }
358
359 static int sunxi_mmc_send_cmd_common(struct sunxi_mmc_priv *priv,
360                                      struct mmc *mmc, struct mmc_cmd *cmd,
361                                      struct mmc_data *data)
362 {
363         unsigned int cmdval = SUNXI_MMC_CMD_START;
364         unsigned int timeout_msecs;
365         int error = 0;
366         unsigned int status = 0;
367         unsigned int bytecnt = 0;
368
369         if (priv->fatal_err)
370                 return -1;
371         if (cmd->resp_type & MMC_RSP_BUSY)
372                 debug("mmc cmd %d check rsp busy\n", cmd->cmdidx);
373         if (cmd->cmdidx == 12)
374                 return 0;
375
376         if (!cmd->cmdidx)
377                 cmdval |= SUNXI_MMC_CMD_SEND_INIT_SEQ;
378         if (cmd->resp_type & MMC_RSP_PRESENT)
379                 cmdval |= SUNXI_MMC_CMD_RESP_EXPIRE;
380         if (cmd->resp_type & MMC_RSP_136)
381                 cmdval |= SUNXI_MMC_CMD_LONG_RESPONSE;
382         if (cmd->resp_type & MMC_RSP_CRC)
383                 cmdval |= SUNXI_MMC_CMD_CHK_RESPONSE_CRC;
384
385         if (data) {
386                 if ((u32)(long)data->dest & 0x3) {
387                         error = -1;
388                         goto out;
389                 }
390
391                 cmdval |= SUNXI_MMC_CMD_DATA_EXPIRE|SUNXI_MMC_CMD_WAIT_PRE_OVER;
392                 if (data->flags & MMC_DATA_WRITE)
393                         cmdval |= SUNXI_MMC_CMD_WRITE;
394                 if (data->blocks > 1)
395                         cmdval |= SUNXI_MMC_CMD_AUTO_STOP;
396                 writel(data->blocksize, &priv->reg->blksz);
397                 writel(data->blocks * data->blocksize, &priv->reg->bytecnt);
398         }
399
400         debug("mmc %d, cmd %d(0x%08x), arg 0x%08x\n", priv->mmc_no,
401               cmd->cmdidx, cmdval | cmd->cmdidx, cmd->cmdarg);
402         writel(cmd->cmdarg, &priv->reg->arg);
403
404         if (!data)
405                 writel(cmdval | cmd->cmdidx, &priv->reg->cmd);
406
407         /*
408          * transfer data and check status
409          * STATREG[2] : FIFO empty
410          * STATREG[3] : FIFO full
411          */
412         if (data) {
413                 int ret = 0;
414
415                 bytecnt = data->blocksize * data->blocks;
416                 debug("trans data %d bytes\n", bytecnt);
417                 writel(cmdval | cmd->cmdidx, &priv->reg->cmd);
418                 ret = mmc_trans_data_by_cpu(priv, mmc, data);
419                 if (ret) {
420                         error = readl(&priv->reg->rint) &
421                                 SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT;
422                         error = -ETIMEDOUT;
423                         goto out;
424                 }
425         }
426
427         error = mmc_rint_wait(priv, mmc, 1000, SUNXI_MMC_RINT_COMMAND_DONE,
428                               "cmd");
429         if (error)
430                 goto out;
431
432         if (data) {
433                 timeout_msecs = 120;
434                 debug("cacl timeout %x msec\n", timeout_msecs);
435                 error = mmc_rint_wait(priv, mmc, timeout_msecs,
436                                       data->blocks > 1 ?
437                                       SUNXI_MMC_RINT_AUTO_COMMAND_DONE :
438                                       SUNXI_MMC_RINT_DATA_OVER,
439                                       "data");
440                 if (error)
441                         goto out;
442         }
443
444         if (cmd->resp_type & MMC_RSP_BUSY) {
445                 unsigned long start = get_timer(0);
446                 timeout_msecs = 2000;
447
448                 do {
449                         status = readl(&priv->reg->status);
450                         if (get_timer(start) > timeout_msecs) {
451                                 debug("busy timeout\n");
452                                 error = -ETIMEDOUT;
453                                 goto out;
454                         }
455                 } while (status & SUNXI_MMC_STATUS_CARD_DATA_BUSY);
456         }
457
458         if (cmd->resp_type & MMC_RSP_136) {
459                 cmd->response[0] = readl(&priv->reg->resp3);
460                 cmd->response[1] = readl(&priv->reg->resp2);
461                 cmd->response[2] = readl(&priv->reg->resp1);
462                 cmd->response[3] = readl(&priv->reg->resp0);
463                 debug("mmc resp 0x%08x 0x%08x 0x%08x 0x%08x\n",
464                       cmd->response[3], cmd->response[2],
465                       cmd->response[1], cmd->response[0]);
466         } else {
467                 cmd->response[0] = readl(&priv->reg->resp0);
468                 debug("mmc resp 0x%08x\n", cmd->response[0]);
469         }
470 out:
471         if (error < 0) {
472                 writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl);
473                 mmc_update_clk(priv);
474         }
475         writel(0xffffffff, &priv->reg->rint);
476         writel(readl(&priv->reg->gctrl) | SUNXI_MMC_GCTRL_FIFO_RESET,
477                &priv->reg->gctrl);
478
479         return error;
480 }
481
482 #if !CONFIG_IS_ENABLED(DM_MMC)
483 static int sunxi_mmc_set_ios_legacy(struct mmc *mmc)
484 {
485         struct sunxi_mmc_priv *priv = mmc->priv;
486
487         return sunxi_mmc_set_ios_common(priv, mmc);
488 }
489
490 static int sunxi_mmc_send_cmd_legacy(struct mmc *mmc, struct mmc_cmd *cmd,
491                                      struct mmc_data *data)
492 {
493         struct sunxi_mmc_priv *priv = mmc->priv;
494
495         return sunxi_mmc_send_cmd_common(priv, mmc, cmd, data);
496 }
497
498 static int sunxi_mmc_getcd_legacy(struct mmc *mmc)
499 {
500         struct sunxi_mmc_priv *priv = mmc->priv;
501         int cd_pin;
502
503         cd_pin = sunxi_mmc_getcd_gpio(priv->mmc_no);
504         if (cd_pin < 0)
505                 return 1;
506
507         return !gpio_get_value(cd_pin);
508 }
509
510 static const struct mmc_ops sunxi_mmc_ops = {
511         .send_cmd       = sunxi_mmc_send_cmd_legacy,
512         .set_ios        = sunxi_mmc_set_ios_legacy,
513         .init           = sunxi_mmc_core_init,
514         .getcd          = sunxi_mmc_getcd_legacy,
515 };
516
517 struct mmc *sunxi_mmc_init(int sdc_no)
518 {
519         struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
520         struct sunxi_mmc_priv *priv = &mmc_host[sdc_no];
521         struct mmc_config *cfg = &priv->cfg;
522         int ret;
523
524         memset(priv, '\0', sizeof(struct sunxi_mmc_priv));
525
526         cfg->name = "SUNXI SD/MMC";
527         cfg->ops  = &sunxi_mmc_ops;
528
529         cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
530         cfg->host_caps = MMC_MODE_4BIT;
531 #if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN8I) || defined(CONFIG_MACH_SUN50I_H6)
532         if (sdc_no == 2)
533                 cfg->host_caps = MMC_MODE_8BIT;
534 #endif
535         cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
536         cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
537
538         cfg->f_min = 400000;
539         cfg->f_max = 52000000;
540
541         if (mmc_resource_init(sdc_no) != 0)
542                 return NULL;
543
544         /* config ahb clock */
545         debug("init mmc %d clock and io\n", sdc_no);
546 #if !defined(CONFIG_MACH_SUN50I_H6)
547         setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MMC(sdc_no));
548
549 #ifdef CONFIG_SUNXI_GEN_SUN6I
550         /* unassert reset */
551         setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MMC(sdc_no));
552 #endif
553 #if defined(CONFIG_MACH_SUN9I)
554         /* sun9i has a mmc-common module, also set the gate and reset there */
555         writel(SUNXI_MMC_COMMON_CLK_GATE | SUNXI_MMC_COMMON_RESET,
556                SUNXI_MMC_COMMON_BASE + 4 * sdc_no);
557 #endif
558 #else /* CONFIG_MACH_SUN50I_H6 */
559         setbits_le32(&ccm->sd_gate_reset, 1 << sdc_no);
560         /* unassert reset */
561         setbits_le32(&ccm->sd_gate_reset, 1 << (RESET_SHIFT + sdc_no));
562 #endif
563         ret = mmc_set_mod_clk(priv, 24000000);
564         if (ret)
565                 return NULL;
566
567         return mmc_create(cfg, priv);
568 }
569 #else
570
571 static int sunxi_mmc_set_ios(struct udevice *dev)
572 {
573         struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
574         struct sunxi_mmc_priv *priv = dev_get_priv(dev);
575
576         return sunxi_mmc_set_ios_common(priv, &plat->mmc);
577 }
578
579 static int sunxi_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
580                               struct mmc_data *data)
581 {
582         struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
583         struct sunxi_mmc_priv *priv = dev_get_priv(dev);
584
585         return sunxi_mmc_send_cmd_common(priv, &plat->mmc, cmd, data);
586 }
587
588 static int sunxi_mmc_getcd(struct udevice *dev)
589 {
590         struct sunxi_mmc_priv *priv = dev_get_priv(dev);
591
592         if (dm_gpio_is_valid(&priv->cd_gpio)) {
593                 int cd_state = dm_gpio_get_value(&priv->cd_gpio);
594
595                 return cd_state ^ priv->cd_inverted;
596         }
597         return 1;
598 }
599
600 static const struct dm_mmc_ops sunxi_mmc_ops = {
601         .send_cmd       = sunxi_mmc_send_cmd,
602         .set_ios        = sunxi_mmc_set_ios,
603         .get_cd         = sunxi_mmc_getcd,
604 };
605
606 static int sunxi_mmc_probe(struct udevice *dev)
607 {
608         struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
609         struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
610         struct sunxi_mmc_priv *priv = dev_get_priv(dev);
611         struct reset_ctl_bulk reset_bulk;
612         struct clk gate_clk;
613         struct mmc_config *cfg = &plat->cfg;
614         struct ofnode_phandle_args args;
615         u32 *ccu_reg;
616         int bus_width, ret;
617
618         cfg->name = dev->name;
619         bus_width = dev_read_u32_default(dev, "bus-width", 1);
620
621         cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
622         cfg->host_caps = 0;
623         if (bus_width == 8)
624                 cfg->host_caps |= MMC_MODE_8BIT;
625         if (bus_width >= 4)
626                 cfg->host_caps |= MMC_MODE_4BIT;
627         cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
628         cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
629
630         cfg->f_min = 400000;
631         cfg->f_max = 52000000;
632
633         priv->reg = (void *)dev_read_addr(dev);
634         priv->variant =
635                 (const struct sunxi_mmc_variant *)dev_get_driver_data(dev);
636
637         /* We don't have a sunxi clock driver so find the clock address here */
638         ret = dev_read_phandle_with_args(dev, "clocks", "#clock-cells", 0,
639                                           1, &args);
640         if (ret)
641                 return ret;
642         ccu_reg = (u32 *)ofnode_get_addr(args.node);
643
644         priv->mmc_no = ((uintptr_t)priv->reg - SUNXI_MMC0_BASE) / 0x1000;
645         priv->mclkreg = (void *)ccu_reg +
646                         (priv->variant->mclk_offset + (priv->mmc_no * 4));
647
648         ret = clk_get_by_name(dev, "ahb", &gate_clk);
649         if (!ret)
650                 clk_enable(&gate_clk);
651
652         ret = reset_get_bulk(dev, &reset_bulk);
653         if (!ret)
654                 reset_deassert_bulk(&reset_bulk);
655
656         ret = mmc_set_mod_clk(priv, 24000000);
657         if (ret)
658                 return ret;
659
660         /* This GPIO is optional */
661         if (!dev_read_bool(dev, "non-removable") &&
662             !gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
663                                   GPIOD_IS_IN)) {
664                 int cd_pin = gpio_get_number(&priv->cd_gpio);
665
666                 sunxi_gpio_set_pull(cd_pin, SUNXI_GPIO_PULL_UP);
667         }
668
669         /* Check if card detect is inverted */
670         priv->cd_inverted = dev_read_bool(dev, "cd-inverted");
671
672         upriv->mmc = &plat->mmc;
673
674         /* Reset controller */
675         writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl);
676         udelay(1000);
677
678         return 0;
679 }
680
681 static int sunxi_mmc_bind(struct udevice *dev)
682 {
683         struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
684
685         return mmc_bind(dev, &plat->mmc, &plat->cfg);
686 }
687
688 static const struct sunxi_mmc_variant sun4i_a10_variant = {
689         .mclk_offset = 0x88,
690 };
691
692 static const struct sunxi_mmc_variant sun9i_a80_variant = {
693         .mclk_offset = 0x410,
694 };
695
696 static const struct sunxi_mmc_variant sun50i_h6_variant = {
697         .mclk_offset = 0x830,
698 };
699
700 static const struct udevice_id sunxi_mmc_ids[] = {
701         {
702           .compatible = "allwinner,sun4i-a10-mmc",
703           .data = (ulong)&sun4i_a10_variant,
704         },
705         {
706           .compatible = "allwinner,sun5i-a13-mmc",
707           .data = (ulong)&sun4i_a10_variant,
708         },
709         {
710           .compatible = "allwinner,sun7i-a20-mmc",
711           .data = (ulong)&sun4i_a10_variant,
712         },
713         {
714           .compatible = "allwinner,sun8i-a83t-emmc",
715           .data = (ulong)&sun4i_a10_variant,
716         },
717         {
718           .compatible = "allwinner,sun9i-a80-mmc",
719           .data = (ulong)&sun9i_a80_variant,
720         },
721         {
722           .compatible = "allwinner,sun50i-a64-mmc",
723           .data = (ulong)&sun4i_a10_variant,
724         },
725         {
726           .compatible = "allwinner,sun50i-a64-emmc",
727           .data = (ulong)&sun4i_a10_variant,
728         },
729         {
730           .compatible = "allwinner,sun50i-h6-mmc",
731           .data = (ulong)&sun50i_h6_variant,
732         },
733         {
734           .compatible = "allwinner,sun50i-h6-emmc",
735           .data = (ulong)&sun50i_h6_variant,
736         },
737         { /* sentinel */ }
738 };
739
740 U_BOOT_DRIVER(sunxi_mmc_drv) = {
741         .name           = "sunxi_mmc",
742         .id             = UCLASS_MMC,
743         .of_match       = sunxi_mmc_ids,
744         .bind           = sunxi_mmc_bind,
745         .probe          = sunxi_mmc_probe,
746         .ops            = &sunxi_mmc_ops,
747         .platdata_auto_alloc_size = sizeof(struct sunxi_mmc_plat),
748         .priv_auto_alloc_size = sizeof(struct sunxi_mmc_priv),
749 };
750 #endif