drivers/mmc/host/sdhci-sprd.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 //
   3 // Secure Digital Host Controller
   4 //
   5 // Copyright (C) 2018 Spreadtrum, Inc.
   6 // Author: Chunyan Zhang <chunyan.zhang@unisoc.com>
   7
   8 #include <linux/delay.h>
   9 #include <linux/dma-mapping.h>
  10 #include <linux/highmem.h>
  11 #include <linux/module.h>
  12 #include <linux/of.h>
  13 #include <linux/of_device.h>
  14 #include <linux/of_gpio.h>
  15 #include <linux/pinctrl/consumer.h>
  16 #include <linux/platform_device.h>
  17 #include <linux/pm_runtime.h>
  18 #include <linux/regulator/consumer.h>
  19 #include <linux/slab.h>
  20
  21 #include "sdhci-pltfm.h"
  22
  23 /* SDHCI_ARGUMENT2 register high 16bit */
  24 #define SDHCI_SPRD_ARG2_STUFF           GENMASK(31, 16)
  25
  26 #define SDHCI_SPRD_REG_32_DLL_CFG       0x200
  27 #define  SDHCI_SPRD_DLL_ALL_CPST_EN     (BIT(18) | BIT(24) | BIT(25) | BIT(26) | BIT(27))
  28 #define  SDHCI_SPRD_DLL_EN              BIT(21)
  29 #define  SDHCI_SPRD_DLL_SEARCH_MODE     BIT(16)
  30 #define  SDHCI_SPRD_DLL_INIT_COUNT      0xc00
  31 #define  SDHCI_SPRD_DLL_PHASE_INTERNAL  0x3
  32
  33 #define SDHCI_SPRD_REG_32_DLL_DLY       0x204
  34
  35 #define SDHCI_SPRD_REG_32_DLL_DLY_OFFSET        0x208
  36 #define  SDHCIBSPRD_IT_WR_DLY_INV               BIT(5)
  37 #define  SDHCI_SPRD_BIT_CMD_DLY_INV             BIT(13)
  38 #define  SDHCI_SPRD_BIT_POSRD_DLY_INV           BIT(21)
  39 #define  SDHCI_SPRD_BIT_NEGRD_DLY_INV           BIT(29)
  40
  41 #define SDHCI_SPRD_REG_32_BUSY_POSI             0x250
  42 #define  SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN        BIT(25)
  43 #define  SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN        BIT(24)
  44
  45 #define SDHCI_SPRD_REG_DEBOUNCE         0x28C
  46 #define  SDHCI_SPRD_BIT_DLL_BAK         BIT(0)
  47 #define  SDHCI_SPRD_BIT_DLL_VAL         BIT(1)
  48
  49 #define  SDHCI_SPRD_INT_SIGNAL_MASK     0x1B7F410B
  50
  51 /* SDHCI_HOST_CONTROL2 */
  52 #define  SDHCI_SPRD_CTRL_HS200          0x0005
  53 #define  SDHCI_SPRD_CTRL_HS400          0x0006
  54 #define  SDHCI_SPRD_CTRL_HS400ES        0x0007
  55
  56 /*
  57  * According to the standard specification, BIT(3) of SDHCI_SOFTWARE_RESET is
  58  * reserved, and only used on Spreadtrum's design, the hardware cannot work
  59  * if this bit is cleared.
  60  * 1 : normal work
  61  * 0 : hardware reset
  62  */
  63 #define  SDHCI_HW_RESET_CARD            BIT(3)
  64
  65 #define SDHCI_SPRD_MAX_CUR              0xFFFFFF
  66 #define SDHCI_SPRD_CLK_MAX_DIV          1023
  67
  68 #define SDHCI_SPRD_CLK_DEF_RATE         26000000
  69 #define SDHCI_SPRD_PHY_DLL_CLK          52000000
  70
  71 struct sdhci_sprd_host {
  72         u32 version;
  73         struct clk *clk_sdio;
  74         struct clk *clk_enable;
  75         struct clk *clk_2x_enable;
  76         struct pinctrl *pinctrl;
  77         struct pinctrl_state *pins_uhs;
  78         struct pinctrl_state *pins_default;
  79         u32 base_rate;
  80         int flags; /* backup of host attribute */
  81         u32 phy_delay[MMC_TIMING_MMC_HS400 + 2];
  82 };
  83
  84 struct sdhci_sprd_phy_cfg {
  85         const char *property;
  86         u8 timing;
  87 };
  88
  89 static const struct sdhci_sprd_phy_cfg sdhci_sprd_phy_cfgs[] = {
  90         { "sprd,phy-delay-legacy", MMC_TIMING_LEGACY, },
  91         { "sprd,phy-delay-sd-highspeed", MMC_TIMING_SD_HS, },
  92         { "sprd,phy-delay-sd-uhs-sdr50", MMC_TIMING_UHS_SDR50, },
  93         { "sprd,phy-delay-sd-uhs-sdr104", MMC_TIMING_UHS_SDR104, },
  94         { "sprd,phy-delay-mmc-highspeed", MMC_TIMING_MMC_HS, },
  95         { "sprd,phy-delay-mmc-ddr52", MMC_TIMING_MMC_DDR52, },
  96         { "sprd,phy-delay-mmc-hs200", MMC_TIMING_MMC_HS200, },
  97         { "sprd,phy-delay-mmc-hs400", MMC_TIMING_MMC_HS400, },
  98         { "sprd,phy-delay-mmc-hs400es", MMC_TIMING_MMC_HS400 + 1, },
  99 };
 100
 101 #define TO_SPRD_HOST(host) sdhci_pltfm_priv(sdhci_priv(host))
 102
 103 static void sdhci_sprd_init_config(struct sdhci_host *host)
 104 {
 105         u16 val;
 106
 107         /* set dll backup mode */
 108         val = sdhci_readl(host, SDHCI_SPRD_REG_DEBOUNCE);
 109         val |= SDHCI_SPRD_BIT_DLL_BAK | SDHCI_SPRD_BIT_DLL_VAL;
 110         sdhci_writel(host, val, SDHCI_SPRD_REG_DEBOUNCE);
 111 }
 112
 113 static inline u32 sdhci_sprd_readl(struct sdhci_host *host, int reg)
 114 {
 115         if (unlikely(reg == SDHCI_MAX_CURRENT))
 116                 return SDHCI_SPRD_MAX_CUR;
 117
 118         return readl_relaxed(host->ioaddr + reg);
 119 }
 120
 121 static inline void sdhci_sprd_writel(struct sdhci_host *host, u32 val, int reg)
 122 {
 123         /* SDHCI_MAX_CURRENT is reserved on Spreadtrum's platform */
 124         if (unlikely(reg == SDHCI_MAX_CURRENT))
 125                 return;
 126
 127         if (unlikely(reg == SDHCI_SIGNAL_ENABLE || reg == SDHCI_INT_ENABLE))
 128                 val = val & SDHCI_SPRD_INT_SIGNAL_MASK;
 129
 130         writel_relaxed(val, host->ioaddr + reg);
 131 }
 132
 133 static inline void sdhci_sprd_writew(struct sdhci_host *host, u16 val, int reg)
 134 {
 135         /* SDHCI_BLOCK_COUNT is Read Only on Spreadtrum's platform */
 136         if (unlikely(reg == SDHCI_BLOCK_COUNT))
 137                 return;
 138
 139         writew_relaxed(val, host->ioaddr + reg);
 140 }
 141
 142 static inline void sdhci_sprd_writeb(struct sdhci_host *host, u8 val, int reg)
 143 {
 144         /*
 145          * Since BIT(3) of SDHCI_SOFTWARE_RESET is reserved according to the
 146          * standard specification, sdhci_reset() write this register directly
 147          * without checking other reserved bits, that will clear BIT(3) which
 148          * is defined as hardware reset on Spreadtrum's platform and clearing
 149          * it by mistake will lead the card not work. So here we need to work
 150          * around it.
 151          */
 152         if (unlikely(reg == SDHCI_SOFTWARE_RESET)) {
 153                 if (readb_relaxed(host->ioaddr + reg) & SDHCI_HW_RESET_CARD)
 154                         val |= SDHCI_HW_RESET_CARD;
 155         }
 156
 157         writeb_relaxed(val, host->ioaddr + reg);
 158 }
 159
 160 static inline void sdhci_sprd_sd_clk_off(struct sdhci_host *host)
 161 {
 162         u16 ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
 163
 164         ctrl &= ~SDHCI_CLOCK_CARD_EN;
 165         sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL);
 166 }
 167
 168 static inline void sdhci_sprd_sd_clk_on(struct sdhci_host *host)
 169 {
 170         u16 ctrl;
 171
 172         ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
 173         ctrl |= SDHCI_CLOCK_CARD_EN;
 174         sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL);
 175 }
 176
 177 static inline void
 178 sdhci_sprd_set_dll_invert(struct sdhci_host *host, u32 mask, bool en)
 179 {
 180         u32 dll_dly_offset;
 181
 182         dll_dly_offset = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET);
 183         if (en)
 184                 dll_dly_offset |= mask;
 185         else
 186                 dll_dly_offset &= ~mask;
 187         sdhci_writel(host, dll_dly_offset, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET);
 188 }
 189
 190 static inline u32 sdhci_sprd_calc_div(u32 base_clk, u32 clk)
 191 {
 192         u32 div;
 193
 194         /* select 2x clock source */
 195         if (base_clk <= clk * 2)
 196                 return 0;
 197
 198         div = (u32) (base_clk / (clk * 2));
 199
 200         if ((base_clk / div) > (clk * 2))
 201                 div++;
 202
 203         if (div > SDHCI_SPRD_CLK_MAX_DIV)
 204                 div = SDHCI_SPRD_CLK_MAX_DIV;
 205
 206         if (div % 2)
 207                 div = (div + 1) / 2;
 208         else
 209                 div = div / 2;
 210
 211         return div;
 212 }
 213
 214 static inline void _sdhci_sprd_set_clock(struct sdhci_host *host,
 215                                         unsigned int clk)
 216 {
 217         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 218         u32 div, val, mask;
 219
 220         sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
 221
 222         div = sdhci_sprd_calc_div(sprd_host->base_rate, clk);
 223         div = ((div & 0x300) >> 2) | ((div & 0xFF) << 8);
 224         sdhci_enable_clk(host, div);
 225
 226         /* enable auto gate sdhc_enable_auto_gate */
 227         val = sdhci_readl(host, SDHCI_SPRD_REG_32_BUSY_POSI);
 228         mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN |
 229                SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN;
 230         if (mask != (val & mask)) {
 231                 val |= mask;
 232                 sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI);
 233         }
 234 }
 235
 236 static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host)
 237 {
 238         u32 tmp;
 239
 240         tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
 241         tmp &= ~(SDHCI_SPRD_DLL_EN | SDHCI_SPRD_DLL_ALL_CPST_EN);
 242         sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
 243         /* wait 1ms */
 244         usleep_range(1000, 1250);
 245
 246         tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
 247         tmp |= SDHCI_SPRD_DLL_ALL_CPST_EN | SDHCI_SPRD_DLL_SEARCH_MODE |
 248                 SDHCI_SPRD_DLL_INIT_COUNT | SDHCI_SPRD_DLL_PHASE_INTERNAL;
 249         sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
 250         /* wait 1ms */
 251         usleep_range(1000, 1250);
 252
 253         tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
 254         tmp |= SDHCI_SPRD_DLL_EN;
 255         sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
 256         /* wait 1ms */
 257         usleep_range(1000, 1250);
 258 }
 259
 260 static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock)
 261 {
 262         bool en = false, clk_changed = false;
 263
 264         if (clock == 0) {
 265                 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
 266         } else if (clock != host->clock) {
 267                 sdhci_sprd_sd_clk_off(host);
 268                 _sdhci_sprd_set_clock(host, clock);
 269
 270                 if (clock <= 400000)
 271                         en = true;
 272                 sdhci_sprd_set_dll_invert(host, SDHCI_SPRD_BIT_CMD_DLY_INV |
 273                                           SDHCI_SPRD_BIT_POSRD_DLY_INV, en);
 274                 clk_changed = true;
 275         } else {
 276                 _sdhci_sprd_set_clock(host, clock);
 277         }
 278
 279         /*
 280          * According to the Spreadtrum SD host specification, when we changed
 281          * the clock to be more than 52M, we should enable the PHY DLL which
 282          * is used to track the clock frequency to make the clock work more
 283          * stable. Otherwise deviation may occur of the higher clock.
 284          */
 285         if (clk_changed && clock > SDHCI_SPRD_PHY_DLL_CLK)
 286                 sdhci_sprd_enable_phy_dll(host);
 287 }
 288
 289 static unsigned int sdhci_sprd_get_max_clock(struct sdhci_host *host)
 290 {
 291         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 292
 293         return clk_round_rate(sprd_host->clk_sdio, ULONG_MAX);
 294 }
 295
 296 static unsigned int sdhci_sprd_get_min_clock(struct sdhci_host *host)
 297 {
 298         return 400000;
 299 }
 300
 301 static void sdhci_sprd_set_uhs_signaling(struct sdhci_host *host,
 302                                          unsigned int timing)
 303 {
 304         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 305         struct mmc_host *mmc = host->mmc;
 306         u32 *p = sprd_host->phy_delay;
 307         u16 ctrl_2;
 308
 309         if (timing == host->timing)
 310                 return;
 311
 312         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 313         /* Select Bus Speed Mode for host */
 314         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
 315         switch (timing) {
 316         case MMC_TIMING_UHS_SDR12:
 317                 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
 318                 break;
 319         case MMC_TIMING_MMC_HS:
 320         case MMC_TIMING_SD_HS:
 321         case MMC_TIMING_UHS_SDR25:
 322                 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
 323                 break;
 324         case MMC_TIMING_UHS_SDR50:
 325                 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
 326                 break;
 327         case MMC_TIMING_UHS_SDR104:
 328                 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
 329                 break;
 330         case MMC_TIMING_UHS_DDR50:
 331         case MMC_TIMING_MMC_DDR52:
 332                 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
 333                 break;
 334         case MMC_TIMING_MMC_HS200:
 335                 ctrl_2 |= SDHCI_SPRD_CTRL_HS200;
 336                 break;
 337         case MMC_TIMING_MMC_HS400:
 338                 ctrl_2 |= SDHCI_SPRD_CTRL_HS400;
 339                 break;
 340         default:
 341                 break;
 342         }
 343
 344         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
 345
 346         if (!mmc->ios.enhanced_strobe)
 347                 sdhci_writel(host, p[timing], SDHCI_SPRD_REG_32_DLL_DLY);
 348 }
 349
 350 static void sdhci_sprd_hw_reset(struct sdhci_host *host)
 351 {
 352         int val;
 353
 354         /*
 355          * Note: don't use sdhci_writeb() API here since it is redirected to
 356          * sdhci_sprd_writeb() in which we have a workaround for
 357          * SDHCI_SOFTWARE_RESET which would make bit SDHCI_HW_RESET_CARD can
 358          * not be cleared.
 359          */
 360         val = readb_relaxed(host->ioaddr + SDHCI_SOFTWARE_RESET);
 361         val &= ~SDHCI_HW_RESET_CARD;
 362         writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET);
 363         /* wait for 10 us */
 364         usleep_range(10, 20);
 365
 366         val |= SDHCI_HW_RESET_CARD;
 367         writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET);
 368         usleep_range(300, 500);
 369 }
 370
 371 static unsigned int sdhci_sprd_get_max_timeout_count(struct sdhci_host *host)
 372 {
 373         /* The Spredtrum controller actual maximum timeout count is 1 << 31 */
 374         return 1 << 31;
 375 }
 376
 377 static unsigned int sdhci_sprd_get_ro(struct sdhci_host *host)
 378 {
 379         return 0;
 380 }
 381
 382 static struct sdhci_ops sdhci_sprd_ops = {
 383         .read_l = sdhci_sprd_readl,
 384         .write_l = sdhci_sprd_writel,
 385         .write_b = sdhci_sprd_writeb,
 386         .set_clock = sdhci_sprd_set_clock,
 387         .get_max_clock = sdhci_sprd_get_max_clock,
 388         .get_min_clock = sdhci_sprd_get_min_clock,
 389         .set_bus_width = sdhci_set_bus_width,
 390         .reset = sdhci_reset,
 391         .set_uhs_signaling = sdhci_sprd_set_uhs_signaling,
 392         .hw_reset = sdhci_sprd_hw_reset,
 393         .get_max_timeout_count = sdhci_sprd_get_max_timeout_count,
 394         .get_ro = sdhci_sprd_get_ro,
 395 };
 396
 397 static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq)
 398 {
 399         struct sdhci_host *host = mmc_priv(mmc);
 400         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 401
 402         host->flags |= sprd_host->flags & SDHCI_AUTO_CMD23;
 403
 404         /*
 405          * From version 4.10 onward, ARGUMENT2 register is also as 32-bit
 406          * block count register which doesn't support stuff bits of
 407          * CMD23 argument on Spreadtrum's sd host controller.
 408          */
 409         if (host->version >= SDHCI_SPEC_410 &&
 410             mrq->sbc && (mrq->sbc->arg & SDHCI_SPRD_ARG2_STUFF) &&
 411             (host->flags & SDHCI_AUTO_CMD23))
 412                 host->flags &= ~SDHCI_AUTO_CMD23;
 413
 414         sdhci_request(mmc, mrq);
 415 }
 416
 417 static int sdhci_sprd_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios)
 418 {
 419         struct sdhci_host *host = mmc_priv(mmc);
 420         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 421         int ret;
 422
 423         if (!IS_ERR(mmc->supply.vqmmc)) {
 424                 ret = mmc_regulator_set_vqmmc(mmc, ios);
 425                 if (ret) {
 426                         pr_err("%s: Switching signalling voltage failed\n",
 427                                mmc_hostname(mmc));
 428                         return ret;
 429                 }
 430         }
 431
 432         if (IS_ERR(sprd_host->pinctrl))
 433                 return 0;
 434
 435         switch (ios->signal_voltage) {
 436         case MMC_SIGNAL_VOLTAGE_180:
 437                 ret = pinctrl_select_state(sprd_host->pinctrl,
 438                                            sprd_host->pins_uhs);
 439                 if (ret) {
 440                         pr_err("%s: failed to select uhs pin state\n",
 441                                mmc_hostname(mmc));
 442                         return ret;
 443                 }
 444                 break;
 445
 446         default:
 447                 /* fall-through */
 448         case MMC_SIGNAL_VOLTAGE_330:
 449                 ret = pinctrl_select_state(sprd_host->pinctrl,
 450                                            sprd_host->pins_default);
 451                 if (ret) {
 452                         pr_err("%s: failed to select default pin state\n",
 453                                mmc_hostname(mmc));
 454                         return ret;
 455                 }
 456                 break;
 457         }
 458
 459         /* Wait for 300 ~ 500 us for pin state stable */
 460         usleep_range(300, 500);
 461         sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
 462
 463         return 0;
 464 }
 465
 466 static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc,
 467                                              struct mmc_ios *ios)
 468 {
 469         struct sdhci_host *host = mmc_priv(mmc);
 470         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 471         u32 *p = sprd_host->phy_delay;
 472         u16 ctrl_2;
 473
 474         if (!ios->enhanced_strobe)
 475                 return;
 476
 477         sdhci_sprd_sd_clk_off(host);
 478
 479         /* Set HS400 enhanced strobe mode */
 480         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 481         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
 482         ctrl_2 |= SDHCI_SPRD_CTRL_HS400ES;
 483         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
 484
 485         sdhci_sprd_sd_clk_on(host);
 486
 487         /* Set the PHY DLL delay value for HS400 enhanced strobe mode */
 488         sdhci_writel(host, p[MMC_TIMING_MMC_HS400 + 1],
 489                      SDHCI_SPRD_REG_32_DLL_DLY);
 490 }
 491
 492 static void sdhci_sprd_phy_param_parse(struct sdhci_sprd_host *sprd_host,
 493                                        struct device_node *np)
 494 {
 495         u32 *p = sprd_host->phy_delay;
 496         int ret, i, index;
 497         u32 val[4];
 498
 499         for (i = 0; i < ARRAY_SIZE(sdhci_sprd_phy_cfgs); i++) {
 500                 ret = of_property_read_u32_array(np,
 501                                 sdhci_sprd_phy_cfgs[i].property, val, 4);
 502                 if (ret)
 503                         continue;
 504
 505                 index = sdhci_sprd_phy_cfgs[i].timing;
 506                 p[index] = val[0] | (val[1] << 8) | (val[2] << 16) | (val[3] << 24);
 507         }
 508 }
 509
 510 static const struct sdhci_pltfm_data sdhci_sprd_pdata = {
 511         .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
 512                   SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
 513                   SDHCI_QUIRK_MISSING_CAPS,
 514         .quirks2 = SDHCI_QUIRK2_BROKEN_HS200 |
 515                    SDHCI_QUIRK2_USE_32BIT_BLK_CNT |
 516                    SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
 517         .ops = &sdhci_sprd_ops,
 518 };
 519
 520 static int sdhci_sprd_probe(struct platform_device *pdev)
 521 {
 522         struct sdhci_host *host;
 523         struct sdhci_sprd_host *sprd_host;
 524         struct clk *clk;
 525         int ret = 0;
 526
 527         host = sdhci_pltfm_init(pdev, &sdhci_sprd_pdata, sizeof(*sprd_host));
 528         if (IS_ERR(host))
 529                 return PTR_ERR(host);
 530
 531         host->dma_mask = DMA_BIT_MASK(64);
 532         pdev->dev.dma_mask = &host->dma_mask;
 533         host->mmc_host_ops.request = sdhci_sprd_request;
 534         host->mmc_host_ops.hs400_enhanced_strobe =
 535                 sdhci_sprd_hs400_enhanced_strobe;
 536         /*
 537          * We can not use the standard ops to change and detect the voltage
 538          * signal for Spreadtrum SD host controller, since our voltage regulator
 539          * for I/O is fixed in hardware, that means we do not need control
 540          * the standard SD host controller to change the I/O voltage.
 541          */
 542         host->mmc_host_ops.start_signal_voltage_switch =
 543                 sdhci_sprd_voltage_switch;
 544
 545         host->mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED |
 546                 MMC_CAP_ERASE | MMC_CAP_CMD23;
 547         ret = mmc_of_parse(host->mmc);
 548         if (ret)
 549                 goto pltfm_free;
 550
 551         sprd_host = TO_SPRD_HOST(host);
 552         sdhci_sprd_phy_param_parse(sprd_host, pdev->dev.of_node);
 553
 554         sprd_host->pinctrl = devm_pinctrl_get(&pdev->dev);
 555         if (!IS_ERR(sprd_host->pinctrl)) {
 556                 sprd_host->pins_uhs =
 557                         pinctrl_lookup_state(sprd_host->pinctrl, "state_uhs");
 558                 if (IS_ERR(sprd_host->pins_uhs)) {
 559                         ret = PTR_ERR(sprd_host->pins_uhs);
 560                         goto pltfm_free;
 561                 }
 562
 563                 sprd_host->pins_default =
 564                         pinctrl_lookup_state(sprd_host->pinctrl, "default");
 565                 if (IS_ERR(sprd_host->pins_default)) {
 566                         ret = PTR_ERR(sprd_host->pins_default);
 567                         goto pltfm_free;
 568                 }
 569         }
 570
 571         clk = devm_clk_get(&pdev->dev, "sdio");
 572         if (IS_ERR(clk)) {
 573                 ret = PTR_ERR(clk);
 574                 goto pltfm_free;
 575         }
 576         sprd_host->clk_sdio = clk;
 577         sprd_host->base_rate = clk_get_rate(sprd_host->clk_sdio);
 578         if (!sprd_host->base_rate)
 579                 sprd_host->base_rate = SDHCI_SPRD_CLK_DEF_RATE;
 580
 581         clk = devm_clk_get(&pdev->dev, "enable");
 582         if (IS_ERR(clk)) {
 583                 ret = PTR_ERR(clk);
 584                 goto pltfm_free;
 585         }
 586         sprd_host->clk_enable = clk;
 587
 588         clk = devm_clk_get(&pdev->dev, "2x_enable");
 589         if (!IS_ERR(clk))
 590                 sprd_host->clk_2x_enable = clk;
 591
 592         ret = clk_prepare_enable(sprd_host->clk_sdio);
 593         if (ret)
 594                 goto pltfm_free;
 595
 596         ret = clk_prepare_enable(sprd_host->clk_enable);
 597         if (ret)
 598                 goto clk_disable;
 599
 600         ret = clk_prepare_enable(sprd_host->clk_2x_enable);
 601         if (ret)
 602                 goto clk_disable2;
 603
 604         sdhci_sprd_init_config(host);
 605         host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
 606         sprd_host->version = ((host->version & SDHCI_VENDOR_VER_MASK) >>
 607                                SDHCI_VENDOR_VER_SHIFT);
 608
 609         pm_runtime_get_noresume(&pdev->dev);
 610         pm_runtime_set_active(&pdev->dev);
 611         pm_runtime_enable(&pdev->dev);
 612         pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
 613         pm_runtime_use_autosuspend(&pdev->dev);
 614         pm_suspend_ignore_children(&pdev->dev, 1);
 615
 616         sdhci_enable_v4_mode(host);
 617
 618         /*
 619          * Supply the existing CAPS, but clear the UHS-I modes. This
 620          * will allow these modes to be specified only by device
 621          * tree properties through mmc_of_parse().
 622          */
 623         host->caps = sdhci_readl(host, SDHCI_CAPABILITIES);
 624         host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
 625         host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 |
 626                          SDHCI_SUPPORT_DDR50);
 627
 628         ret = sdhci_setup_host(host);
 629         if (ret)
 630                 goto pm_runtime_disable;
 631
 632         sprd_host->flags = host->flags;
 633
 634         ret = __sdhci_add_host(host);
 635         if (ret)
 636                 goto err_cleanup_host;
 637
 638         pm_runtime_mark_last_busy(&pdev->dev);
 639         pm_runtime_put_autosuspend(&pdev->dev);
 640
 641         return 0;
 642
 643 err_cleanup_host:
 644         sdhci_cleanup_host(host);
 645
 646 pm_runtime_disable:
 647         pm_runtime_put_noidle(&pdev->dev);
 648         pm_runtime_disable(&pdev->dev);
 649         pm_runtime_set_suspended(&pdev->dev);
 650
 651         clk_disable_unprepare(sprd_host->clk_2x_enable);
 652
 653 clk_disable2:
 654         clk_disable_unprepare(sprd_host->clk_enable);
 655
 656 clk_disable:
 657         clk_disable_unprepare(sprd_host->clk_sdio);
 658
 659 pltfm_free:
 660         sdhci_pltfm_free(pdev);
 661         return ret;
 662 }
 663
 664 static int sdhci_sprd_remove(struct platform_device *pdev)
 665 {
 666         struct sdhci_host *host = platform_get_drvdata(pdev);
 667         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 668         struct mmc_host *mmc = host->mmc;
 669
 670         mmc_remove_host(mmc);
 671         clk_disable_unprepare(sprd_host->clk_sdio);
 672         clk_disable_unprepare(sprd_host->clk_enable);
 673         clk_disable_unprepare(sprd_host->clk_2x_enable);
 674
 675         mmc_free_host(mmc);
 676
 677         return 0;
 678 }
 679
 680 static const struct of_device_id sdhci_sprd_of_match[] = {
 681         { .compatible = "sprd,sdhci-r11", },
 682         { }
 683 };
 684 MODULE_DEVICE_TABLE(of, sdhci_sprd_of_match);
 685
 686 #ifdef CONFIG_PM
 687 static int sdhci_sprd_runtime_suspend(struct device *dev)
 688 {
 689         struct sdhci_host *host = dev_get_drvdata(dev);
 690         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 691
 692         sdhci_runtime_suspend_host(host);
 693
 694         clk_disable_unprepare(sprd_host->clk_sdio);
 695         clk_disable_unprepare(sprd_host->clk_enable);
 696         clk_disable_unprepare(sprd_host->clk_2x_enable);
 697
 698         return 0;
 699 }
 700
 701 static int sdhci_sprd_runtime_resume(struct device *dev)
 702 {
 703         struct sdhci_host *host = dev_get_drvdata(dev);
 704         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 705         int ret;
 706
 707         ret = clk_prepare_enable(sprd_host->clk_2x_enable);
 708         if (ret)
 709                 return ret;
 710
 711         ret = clk_prepare_enable(sprd_host->clk_enable);
 712         if (ret)
 713                 goto clk_2x_disable;
 714
 715         ret = clk_prepare_enable(sprd_host->clk_sdio);
 716         if (ret)
 717                 goto clk_disable;
 718
 719         sdhci_runtime_resume_host(host, 1);
 720         return 0;
 721
 722 clk_disable:
 723         clk_disable_unprepare(sprd_host->clk_enable);
 724
 725 clk_2x_disable:
 726         clk_disable_unprepare(sprd_host->clk_2x_enable);
 727
 728         return ret;
 729 }
 730 #endif
 731
 732 static const struct dev_pm_ops sdhci_sprd_pm_ops = {
 733         SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
 734                                 pm_runtime_force_resume)
 735         SET_RUNTIME_PM_OPS(sdhci_sprd_runtime_suspend,
 736                            sdhci_sprd_runtime_resume, NULL)
 737 };
 738
 739 static struct platform_driver sdhci_sprd_driver = {
 740         .probe = sdhci_sprd_probe,
 741         .remove = sdhci_sprd_remove,
 742         .driver = {
 743                 .name = "sdhci_sprd_r11",
 744                 .of_match_table = of_match_ptr(sdhci_sprd_of_match),
 745                 .pm = &sdhci_sprd_pm_ops,
 746         },
 747 };
 748 module_platform_driver(sdhci_sprd_driver);
 749
 750 MODULE_DESCRIPTION("Spreadtrum sdio host controller r11 driver");
 751 MODULE_LICENSE("GPL v2");
 752 MODULE_ALIAS("platform:sdhci-sprd-r11");