Linux-libre 4.14.12-gnu

[librecmc/linux-libre.git] / drivers / mmc / core / core.c

/*
 *  linux/drivers/mmc/core/core.c
 *
 *  Copyright (C) 2003-2004 Russell King, All Rights Reserved.
 *  SD support Copyright (C) 2004 Ian Molton, All Rights Reserved.
 *  Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
 *  MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */
#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/completion.h>
#include <linux/device.h>
#include <linux/delay.h>
#include <linux/pagemap.h>
#include <linux/err.h>
#include <linux/leds.h>
#include <linux/scatterlist.h>
#include <linux/log2.h>
#include <linux/regulator/consumer.h>
#include <linux/pm_runtime.h>
#include <linux/pm_wakeup.h>
#include <linux/suspend.h>
#include <linux/fault-inject.h>
#include <linux/random.h>
#include <linux/slab.h>
#include <linux/of.h>

#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h>
#include <linux/mmc/sd.h>
#include <linux/mmc/slot-gpio.h>

#define CREATE_TRACE_POINTS
#include <trace/events/mmc.h>

#include "core.h"
#include "card.h"
#include "bus.h"
#include "host.h"
#include "sdio_bus.h"
#include "pwrseq.h"

#include "mmc_ops.h"
#include "sd_ops.h"
#include "sdio_ops.h"

/* If the device is not responding */
#define MMC_CORE_TIMEOUT_MS     (10 * 60 * 1000) /* 10 minute timeout */

/* The max erase timeout, used when host->max_busy_timeout isn't specified */
#define MMC_ERASE_TIMEOUT_MS    (60 * 1000) /* 60 s */

static const unsigned freqs[] = { 400000, 300000, 200000, 100000 };

/*
 * Enabling software CRCs on the data blocks can be a significant (30%)
 * performance cost, and for other reasons may not always be desired.
 * So we allow it it to be disabled.
 */
bool use_spi_crc = 1;
module_param(use_spi_crc, bool, 0);

static int mmc_schedule_delayed_work(struct delayed_work *work,
                                     unsigned long delay)
{
        /*
         * We use the system_freezable_wq, because of two reasons.
         * First, it allows several works (not the same work item) to be
         * executed simultaneously. Second, the queue becomes frozen when
         * userspace becomes frozen during system PM.
         */
        return queue_delayed_work(system_freezable_wq, work, delay);
}

#ifdef CONFIG_FAIL_MMC_REQUEST

/*
 * Internal function. Inject random data errors.
 * If mmc_data is NULL no errors are injected.
 */
static void mmc_should_fail_request(struct mmc_host *host,
                                    struct mmc_request *mrq)
{
        struct mmc_command *cmd = mrq->cmd;
        struct mmc_data *data = mrq->data;
        static const int data_errors[] = {
                -ETIMEDOUT,
                -EILSEQ,
                -EIO,
        };

        if (!data)
                return;

        if (cmd->error || data->error ||
            !should_fail(&host->fail_mmc_request, data->blksz * data->blocks))
                return;

        data->error = data_errors[prandom_u32() % ARRAY_SIZE(data_errors)];
        data->bytes_xfered = (prandom_u32() % (data->bytes_xfered >> 9)) << 9;
}

#else /* CONFIG_FAIL_MMC_REQUEST */

static inline void mmc_should_fail_request(struct mmc_host *host,
                                           struct mmc_request *mrq)
{
}

#endif /* CONFIG_FAIL_MMC_REQUEST */

static inline void mmc_complete_cmd(struct mmc_request *mrq)
{
        if (mrq->cap_cmd_during_tfr && !completion_done(&mrq->cmd_completion))
                complete_all(&mrq->cmd_completion);
}

void mmc_command_done(struct mmc_host *host, struct mmc_request *mrq)
{
        if (!mrq->cap_cmd_during_tfr)
                return;

        mmc_complete_cmd(mrq);

        pr_debug("%s: cmd done, tfr ongoing (CMD%u)\n",
                 mmc_hostname(host), mrq->cmd->opcode);
}
EXPORT_SYMBOL(mmc_command_done);

/**
 *      mmc_request_done - finish processing an MMC request
 *      @host: MMC host which completed request
 *      @mrq: MMC request which request
 *
 *      MMC drivers should call this function when they have completed
 *      their processing of a request.
 */
void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq)
{
        struct mmc_command *cmd = mrq->cmd;
        int err = cmd->error;

        /* Flag re-tuning needed on CRC errors */
        if ((cmd->opcode != MMC_SEND_TUNING_BLOCK &&
            cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200) &&
            (err == -EILSEQ || (mrq->sbc && mrq->sbc->error == -EILSEQ) ||
            (mrq->data && mrq->data->error == -EILSEQ) ||
            (mrq->stop && mrq->stop->error == -EILSEQ)))
                mmc_retune_needed(host);

        if (err && cmd->retries && mmc_host_is_spi(host)) {
                if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
                        cmd->retries = 0;
        }

        if (host->ongoing_mrq == mrq)
                host->ongoing_mrq = NULL;

        mmc_complete_cmd(mrq);

        trace_mmc_request_done(host, mrq);

        /*
         * We list various conditions for the command to be considered
         * properly done:
         *
         * - There was no error, OK fine then
         * - We are not doing some kind of retry
         * - The card was removed (...so just complete everything no matter
         *   if there are errors or retries)
         */
        if (!err || !cmd->retries || mmc_card_removed(host->card)) {
                mmc_should_fail_request(host, mrq);

                if (!host->ongoing_mrq)
                        led_trigger_event(host->led, LED_OFF);

                if (mrq->sbc) {
                        pr_debug("%s: req done <CMD%u>: %d: %08x %08x %08x %08x\n",
                                mmc_hostname(host), mrq->sbc->opcode,
                                mrq->sbc->error,
                                mrq->sbc->resp[0], mrq->sbc->resp[1],
                                mrq->sbc->resp[2], mrq->sbc->resp[3]);
                }

                pr_debug("%s: req done (CMD%u): %d: %08x %08x %08x %08x\n",
                        mmc_hostname(host), cmd->opcode, err,
                        cmd->resp[0], cmd->resp[1],
                        cmd->resp[2], cmd->resp[3]);

                if (mrq->data) {
                        pr_debug("%s:     %d bytes transferred: %d\n",
                                mmc_hostname(host),
                                mrq->data->bytes_xfered, mrq->data->error);
                }

                if (mrq->stop) {
                        pr_debug("%s:     (CMD%u): %d: %08x %08x %08x %08x\n",
                                mmc_hostname(host), mrq->stop->opcode,
                                mrq->stop->error,
                                mrq->stop->resp[0], mrq->stop->resp[1],
                                mrq->stop->resp[2], mrq->stop->resp[3]);
                }
        }
        /*
         * Request starter must handle retries - see
         * mmc_wait_for_req_done().
         */
        if (mrq->done)
                mrq->done(mrq);
}

EXPORT_SYMBOL(mmc_request_done);

static void __mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
{
        int err;

        /* Assumes host controller has been runtime resumed by mmc_claim_host */
        err = mmc_retune(host);
        if (err) {
                mrq->cmd->error = err;
                mmc_request_done(host, mrq);
                return;
        }

        /*
         * For sdio rw commands we must wait for card busy otherwise some
         * sdio devices won't work properly.
         * And bypass I/O abort, reset and bus suspend operations.
         */
        if (sdio_is_io_busy(mrq->cmd->opcode, mrq->cmd->arg) &&
            host->ops->card_busy) {
                int tries = 500; /* Wait aprox 500ms at maximum */

                while (host->ops->card_busy(host) && --tries)
                        mmc_delay(1);

                if (tries == 0) {
                        mrq->cmd->error = -EBUSY;
                        mmc_request_done(host, mrq);
                        return;
                }
        }

        if (mrq->cap_cmd_during_tfr) {
                host->ongoing_mrq = mrq;
                /*
                 * Retry path could come through here without having waiting on
                 * cmd_completion, so ensure it is reinitialised.
                 */
                reinit_completion(&mrq->cmd_completion);
        }

        trace_mmc_request_start(host, mrq);

        if (host->cqe_on)
                host->cqe_ops->cqe_off(host);

        host->ops->request(host, mrq);
}

static void mmc_mrq_pr_debug(struct mmc_host *host, struct mmc_request *mrq)
{
        if (mrq->sbc) {
                pr_debug("<%s: starting CMD%u arg %08x flags %08x>\n",
                         mmc_hostname(host), mrq->sbc->opcode,
                         mrq->sbc->arg, mrq->sbc->flags);
        }

        if (mrq->cmd) {
                pr_debug("%s: starting CMD%u arg %08x flags %08x\n",
                         mmc_hostname(host), mrq->cmd->opcode, mrq->cmd->arg,
                         mrq->cmd->flags);
        }

        if (mrq->data) {
                pr_debug("%s:     blksz %d blocks %d flags %08x "
                        "tsac %d ms nsac %d\n",
                        mmc_hostname(host), mrq->data->blksz,
                        mrq->data->blocks, mrq->data->flags,
                        mrq->data->timeout_ns / 1000000,
                        mrq->data->timeout_clks);
        }

        if (mrq->stop) {
                pr_debug("%s:     CMD%u arg %08x flags %08x\n",
                         mmc_hostname(host), mrq->stop->opcode,
                         mrq->stop->arg, mrq->stop->flags);
        }
}

static int mmc_mrq_prep(struct mmc_host *host, struct mmc_request *mrq)
{
        unsigned int i, sz = 0;
        struct scatterlist *sg;

        if (mrq->cmd) {
                mrq->cmd->error = 0;
                mrq->cmd->mrq = mrq;
                mrq->cmd->data = mrq->data;
        }
        if (mrq->sbc) {
                mrq->sbc->error = 0;
                mrq->sbc->mrq = mrq;
        }
        if (mrq->data) {
                if (mrq->data->blksz > host->max_blk_size ||
                    mrq->data->blocks > host->max_blk_count ||
                    mrq->data->blocks * mrq->data->blksz > host->max_req_size)
                        return -EINVAL;

                for_each_sg(mrq->data->sg, sg, mrq->data->sg_len, i)
                        sz += sg->length;
                if (sz != mrq->data->blocks * mrq->data->blksz)
                        return -EINVAL;

                mrq->data->error = 0;
                mrq->data->mrq = mrq;
                if (mrq->stop) {
                        mrq->data->stop = mrq->stop;
                        mrq->stop->error = 0;
                        mrq->stop->mrq = mrq;
                }
        }

        return 0;
}

static int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
{
        int err;

        mmc_retune_hold(host);

        if (mmc_card_removed(host->card))
                return -ENOMEDIUM;

        mmc_mrq_pr_debug(host, mrq);

        WARN_ON(!host->claimed);

        err = mmc_mrq_prep(host, mrq);
        if (err)
                return err;

        led_trigger_event(host->led, LED_FULL);
        __mmc_start_request(host, mrq);

        return 0;
}

/*
 * mmc_wait_data_done() - done callback for data request
 * @mrq: done data request
 *
 * Wakes up mmc context, passed as a callback to host controller driver
 */
static void mmc_wait_data_done(struct mmc_request *mrq)
{
        struct mmc_context_info *context_info = &mrq->host->context_info;

        context_info->is_done_rcv = true;
        wake_up_interruptible(&context_info->wait);
}

static void mmc_wait_done(struct mmc_request *mrq)
{
        complete(&mrq->completion);
}

static inline void mmc_wait_ongoing_tfr_cmd(struct mmc_host *host)
{
        struct mmc_request *ongoing_mrq = READ_ONCE(host->ongoing_mrq);

        /*
         * If there is an ongoing transfer, wait for the command line to become
         * available.
         */
        if (ongoing_mrq && !completion_done(&ongoing_mrq->cmd_completion))
                wait_for_completion(&ongoing_mrq->cmd_completion);
}

/*
 *__mmc_start_data_req() - starts data request
 * @host: MMC host to start the request
 * @mrq: data request to start
 *
 * Sets the done callback to be called when request is completed by the card.
 * Starts data mmc request execution
 * If an ongoing transfer is already in progress, wait for the command line
 * to become available before sending another command.
 */
static int __mmc_start_data_req(struct mmc_host *host, struct mmc_request *mrq)
{
        int err;

        mmc_wait_ongoing_tfr_cmd(host);

        mrq->done = mmc_wait_data_done;
        mrq->host = host;

        init_completion(&mrq->cmd_completion);

        err = mmc_start_request(host, mrq);
        if (err) {
                mrq->cmd->error = err;
                mmc_complete_cmd(mrq);
                mmc_wait_data_done(mrq);
        }

        return err;
}

static int __mmc_start_req(struct mmc_host *host, struct mmc_request *mrq)
{
        int err;

        mmc_wait_ongoing_tfr_cmd(host);

        init_completion(&mrq->completion);
        mrq->done = mmc_wait_done;

        init_completion(&mrq->cmd_completion);

        err = mmc_start_request(host, mrq);
        if (err) {
                mrq->cmd->error = err;
                mmc_complete_cmd(mrq);
                complete(&mrq->completion);
        }

        return err;
}

void mmc_wait_for_req_done(struct mmc_host *host, struct mmc_request *mrq)
{
        struct mmc_command *cmd;

        while (1) {
                wait_for_completion(&mrq->completion);

                cmd = mrq->cmd;

                /*
                 * If host has timed out waiting for the sanitize
                 * to complete, card might be still in programming state
                 * so let's try to bring the card out of programming
                 * state.
                 */
                if (cmd->sanitize_busy && cmd->error == -ETIMEDOUT) {
                        if (!mmc_interrupt_hpi(host->card)) {
                                pr_warn("%s: %s: Interrupted sanitize\n",
                                        mmc_hostname(host), __func__);
                                cmd->error = 0;
                                break;
                        } else {
                                pr_err("%s: %s: Failed to interrupt sanitize\n",
                                       mmc_hostname(host), __func__);
                        }
                }
                if (!cmd->error || !cmd->retries ||
                    mmc_card_removed(host->card))
                        break;

                mmc_retune_recheck(host);

                pr_debug("%s: req failed (CMD%u): %d, retrying...\n",
                         mmc_hostname(host), cmd->opcode, cmd->error);
                cmd->retries--;
                cmd->error = 0;
                __mmc_start_request(host, mrq);
        }

        mmc_retune_release(host);
}
EXPORT_SYMBOL(mmc_wait_for_req_done);

/**
 *      mmc_is_req_done - Determine if a 'cap_cmd_during_tfr' request is done
 *      @host: MMC host
 *      @mrq: MMC request
 *
 *      mmc_is_req_done() is used with requests that have
 *      mrq->cap_cmd_during_tfr = true. mmc_is_req_done() must be called after
 *      starting a request and before waiting for it to complete. That is,
 *      either in between calls to mmc_start_req(), or after mmc_wait_for_req()
 *      and before mmc_wait_for_req_done(). If it is called at other times the
 *      result is not meaningful.
 */
bool mmc_is_req_done(struct mmc_host *host, struct mmc_request *mrq)
{
        if (host->areq)
                return host->context_info.is_done_rcv;
        else
                return completion_done(&mrq->completion);
}
EXPORT_SYMBOL(mmc_is_req_done);

/**
 *      mmc_pre_req - Prepare for a new request
 *      @host: MMC host to prepare command
 *      @mrq: MMC request to prepare for
 *
 *      mmc_pre_req() is called in prior to mmc_start_req() to let
 *      host prepare for the new request. Preparation of a request may be
 *      performed while another request is running on the host.
 */
static void mmc_pre_req(struct mmc_host *host, struct mmc_request *mrq)
{
        if (host->ops->pre_req)
                host->ops->pre_req(host, mrq);
}

/**
 *      mmc_post_req - Post process a completed request
 *      @host: MMC host to post process command
 *      @mrq: MMC request to post process for
 *      @err: Error, if non zero, clean up any resources made in pre_req
 *
 *      Let the host post process a completed request. Post processing of
 *      a request may be performed while another reuqest is running.
 */
static void mmc_post_req(struct mmc_host *host, struct mmc_request *mrq,
                         int err)
{
        if (host->ops->post_req)
                host->ops->post_req(host, mrq, err);
}

/**
 * mmc_finalize_areq() - finalize an asynchronous request
 * @host: MMC host to finalize any ongoing request on
 *
 * Returns the status of the ongoing asynchronous request, but
 * MMC_BLK_SUCCESS if no request was going on.
 */
static enum mmc_blk_status mmc_finalize_areq(struct mmc_host *host)
{
        struct mmc_context_info *context_info = &host->context_info;
        enum mmc_blk_status status;

        if (!host->areq)
                return MMC_BLK_SUCCESS;

        while (1) {
                wait_event_interruptible(context_info->wait,
                                (context_info->is_done_rcv ||
                                 context_info->is_new_req));

                if (context_info->is_done_rcv) {
                        struct mmc_command *cmd;

                        context_info->is_done_rcv = false;
                        cmd = host->areq->mrq->cmd;

                        if (!cmd->error || !cmd->retries ||
                            mmc_card_removed(host->card)) {
                                status = host->areq->err_check(host->card,
                                                               host->areq);
                                break; /* return status */
                        } else {
                                mmc_retune_recheck(host);
                                pr_info("%s: req failed (CMD%u): %d, retrying...\n",
                                        mmc_hostname(host),
                                        cmd->opcode, cmd->error);
                                cmd->retries--;
                                cmd->error = 0;
                                __mmc_start_request(host, host->areq->mrq);
                                continue; /* wait for done/new event again */
                        }
                }

                return MMC_BLK_NEW_REQUEST;
        }

        mmc_retune_release(host);

        /*
         * Check BKOPS urgency for each R1 response
         */
        if (host->card && mmc_card_mmc(host->card) &&
            ((mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1) ||
             (mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1B)) &&
            (host->areq->mrq->cmd->resp[0] & R1_EXCEPTION_EVENT)) {
                mmc_start_bkops(host->card, true);
        }

        return status;
}

/**
 *      mmc_start_areq - start an asynchronous request
 *      @host: MMC host to start command
 *      @areq: asynchronous request to start
 *      @ret_stat: out parameter for status
 *
 *      Start a new MMC custom command request for a host.
 *      If there is on ongoing async request wait for completion
 *      of that request and start the new one and return.
 *      Does not wait for the new request to complete.
 *
 *      Returns the completed request, NULL in case of none completed.
 *      Wait for the an ongoing request (previoulsy started) to complete and
 *      return the completed request. If there is no ongoing request, NULL
 *      is returned without waiting. NULL is not an error condition.
 */
struct mmc_async_req *mmc_start_areq(struct mmc_host *host,
                                     struct mmc_async_req *areq,
                                     enum mmc_blk_status *ret_stat)
{
        enum mmc_blk_status status;
        int start_err = 0;
        struct mmc_async_req *previous = host->areq;

        /* Prepare a new request */
        if (areq)
                mmc_pre_req(host, areq->mrq);

        /* Finalize previous request */
        status = mmc_finalize_areq(host);
        if (ret_stat)
                *ret_stat = status;

        /* The previous request is still going on... */
        if (status == MMC_BLK_NEW_REQUEST)
                return NULL;

        /* Fine so far, start the new request! */
        if (status == MMC_BLK_SUCCESS && areq)
                start_err = __mmc_start_data_req(host, areq->mrq);

        /* Postprocess the old request at this point */
        if (host->areq)
                mmc_post_req(host, host->areq->mrq, 0);

        /* Cancel a prepared request if it was not started. */
        if ((status != MMC_BLK_SUCCESS || start_err) && areq)
                mmc_post_req(host, areq->mrq, -EINVAL);

        if (status != MMC_BLK_SUCCESS)
                host->areq = NULL;
        else
                host->areq = areq;

        return previous;
}
EXPORT_SYMBOL(mmc_start_areq);

/**
 *      mmc_wait_for_req - start a request and wait for completion
 *      @host: MMC host to start command
 *      @mrq: MMC request to start
 *
 *      Start a new MMC custom command request for a host, and wait
 *      for the command to complete. In the case of 'cap_cmd_during_tfr'
 *      requests, the transfer is ongoing and the caller can issue further
 *      commands that do not use the data lines, and then wait by calling
 *      mmc_wait_for_req_done().
 *      Does not attempt to parse the response.
 */
void mmc_wait_for_req(struct mmc_host *host, struct mmc_request *mrq)
{
        __mmc_start_req(host, mrq);

        if (!mrq->cap_cmd_during_tfr)
                mmc_wait_for_req_done(host, mrq);
}
EXPORT_SYMBOL(mmc_wait_for_req);

/**
 *      mmc_wait_for_cmd - start a command and wait for completion
 *      @host: MMC host to start command
 *      @cmd: MMC command to start
 *      @retries: maximum number of retries
 *
 *      Start a new MMC command for a host, and wait for the command
 *      to complete.  Return any error that occurred while the command
 *      was executing.  Do not attempt to parse the response.
 */
int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd, int retries)
{
        struct mmc_request mrq = {};

        WARN_ON(!host->claimed);

        memset(cmd->resp, 0, sizeof(cmd->resp));
        cmd->retries = retries;

        mrq.cmd = cmd;
        cmd->data = NULL;

        mmc_wait_for_req(host, &mrq);

        return cmd->error;
}

EXPORT_SYMBOL(mmc_wait_for_cmd);

/**
 *      mmc_set_data_timeout - set the timeout for a data command
 *      @data: data phase for command
 *      @card: the MMC card associated with the data transfer
 *
 *      Computes the data timeout parameters according to the
 *      correct algorithm given the card type.
 */
void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card)
{
        unsigned int mult;

        /*
         * SDIO cards only define an upper 1 s limit on access.
         */
        if (mmc_card_sdio(card)) {
                data->timeout_ns = 1000000000;
                data->timeout_clks = 0;
                return;
        }

        /*
         * SD cards use a 100 multiplier rather than 10
         */
        mult = mmc_card_sd(card) ? 100 : 10;

        /*
         * Scale up the multiplier (and therefore the timeout) by
         * the r2w factor for writes.
         */
        if (data->flags & MMC_DATA_WRITE)
                mult <<= card->csd.r2w_factor;

        data->timeout_ns = card->csd.taac_ns * mult;
        data->timeout_clks = card->csd.taac_clks * mult;

        /*
         * SD cards also have an upper limit on the timeout.
         */
        if (mmc_card_sd(card)) {
                unsigned int timeout_us, limit_us;

                timeout_us = data->timeout_ns / 1000;
                if (card->host->ios.clock)
                        timeout_us += data->timeout_clks * 1000 /
                                (card->host->ios.clock / 1000);

                if (data->flags & MMC_DATA_WRITE)
                        /*
                         * The MMC spec "It is strongly recommended
                         * for hosts to implement more than 500ms
                         * timeout value even if the card indicates
                         * the 250ms maximum busy length."  Even the
                         * previous value of 300ms is known to be
                         * insufficient for some cards.
                         */
                        limit_us = 3000000;
                else
                        limit_us = 100000;

                /*
                 * SDHC cards always use these fixed values.
                 */
                if (timeout_us > limit_us) {
                        data->timeout_ns = limit_us * 1000;
                        data->timeout_clks = 0;
                }

                /* assign limit value if invalid */
                if (timeout_us == 0)
                        data->timeout_ns = limit_us * 1000;
        }

        /*
         * Some cards require longer data read timeout than indicated in CSD.
         * Address this by setting the read timeout to a "reasonably high"
         * value. For the cards tested, 600ms has proven enough. If necessary,
         * this value can be increased if other problematic cards require this.
         */
        if (mmc_card_long_read_time(card) && data->flags & MMC_DATA_READ) {
                data->timeout_ns = 600000000;
                data->timeout_clks = 0;
        }

        /*
         * Some cards need very high timeouts if driven in SPI mode.
         * The worst observed timeout was 900ms after writing a
         * continuous stream of data until the internal logic
         * overflowed.
         */
        if (mmc_host_is_spi(card->host)) {
                if (data->flags & MMC_DATA_WRITE) {
                        if (data->timeout_ns < 1000000000)
                                data->timeout_ns = 1000000000;  /* 1s */
                } else {
                        if (data->timeout_ns < 100000000)
                                data->timeout_ns =  100000000;  /* 100ms */
                }
        }
}
EXPORT_SYMBOL(mmc_set_data_timeout);

/**
 *      mmc_align_data_size - pads a transfer size to a more optimal value
 *      @card: the MMC card associated with the data transfer
 *      @sz: original transfer size
 *
 *      Pads the original data size with a number of extra bytes in
 *      order to avoid controller bugs and/or performance hits
 *      (e.g. some controllers revert to PIO for certain sizes).
 *
 *      Returns the improved size, which might be unmodified.
 *
 *      Note that this function is only relevant when issuing a
 *      single scatter gather entry.
 */
unsigned int mmc_align_data_size(struct mmc_card *card, unsigned int sz)
{
        /*
         * FIXME: We don't have a system for the controller to tell
         * the core about its problems yet, so for now we just 32-bit
         * align the size.
         */
        sz = ((sz + 3) / 4) * 4;

        return sz;
}
EXPORT_SYMBOL(mmc_align_data_size);

/**
 *      __mmc_claim_host - exclusively claim a host
 *      @host: mmc host to claim
 *      @abort: whether or not the operation should be aborted
 *
 *      Claim a host for a set of operations.  If @abort is non null and
 *      dereference a non-zero value then this will return prematurely with
 *      that non-zero value without acquiring the lock.  Returns zero
 *      with the lock held otherwise.
 */
int __mmc_claim_host(struct mmc_host *host, atomic_t *abort)
{
        DECLARE_WAITQUEUE(wait, current);
        unsigned long flags;
        int stop;
        bool pm = false;

        might_sleep();

        add_wait_queue(&host->wq, &wait);
        spin_lock_irqsave(&host->lock, flags);
        while (1) {
                set_current_state(TASK_UNINTERRUPTIBLE);
                stop = abort ? atomic_read(abort) : 0;
                if (stop || !host->claimed || host->claimer == current)
                        break;
                spin_unlock_irqrestore(&host->lock, flags);
                schedule();
                spin_lock_irqsave(&host->lock, flags);
        }
        set_current_state(TASK_RUNNING);
        if (!stop) {
                host->claimed = 1;
                host->claimer = current;
                host->claim_cnt += 1;
                if (host->claim_cnt == 1)
                        pm = true;
        } else
                wake_up(&host->wq);
        spin_unlock_irqrestore(&host->lock, flags);
        remove_wait_queue(&host->wq, &wait);

        if (pm)
                pm_runtime_get_sync(mmc_dev(host));

        return stop;
}
EXPORT_SYMBOL(__mmc_claim_host);

/**
 *      mmc_release_host - release a host
 *      @host: mmc host to release
 *
 *      Release a MMC host, allowing others to claim the host
 *      for their operations.
 */
void mmc_release_host(struct mmc_host *host)
{
        unsigned long flags;

        WARN_ON(!host->claimed);

        spin_lock_irqsave(&host->lock, flags);
        if (--host->claim_cnt) {
                /* Release for nested claim */
                spin_unlock_irqrestore(&host->lock, flags);
        } else {
                host->claimed = 0;
                host->claimer = NULL;
                spin_unlock_irqrestore(&host->lock, flags);
                wake_up(&host->wq);
                pm_runtime_mark_last_busy(mmc_dev(host));
                pm_runtime_put_autosuspend(mmc_dev(host));
        }
}
EXPORT_SYMBOL(mmc_release_host);

/*
 * This is a helper function, which fetches a runtime pm reference for the
 * card device and also claims the host.
 */
void mmc_get_card(struct mmc_card *card)
{
        pm_runtime_get_sync(&card->dev);
        mmc_claim_host(card->host);
}
EXPORT_SYMBOL(mmc_get_card);

/*
 * This is a helper function, which releases the host and drops the runtime
 * pm reference for the card device.
 */
void mmc_put_card(struct mmc_card *card)
{
        mmc_release_host(card->host);
        pm_runtime_mark_last_busy(&card->dev);
        pm_runtime_put_autosuspend(&card->dev);
}
EXPORT_SYMBOL(mmc_put_card);

/*
 * Internal function that does the actual ios call to the host driver,
 * optionally printing some debug output.
 */
static inline void mmc_set_ios(struct mmc_host *host)
{
        struct mmc_ios *ios = &host->ios;

        pr_debug("%s: clock %uHz busmode %u powermode %u cs %u Vdd %u "
                "width %u timing %u\n",
                 mmc_hostname(host), ios->clock, ios->bus_mode,
                 ios->power_mode, ios->chip_select, ios->vdd,
                 1 << ios->bus_width, ios->timing);

        host->ops->set_ios(host, ios);
}

/*
 * Control chip select pin on a host.
 */
void mmc_set_chip_select(struct mmc_host *host, int mode)
{
        host->ios.chip_select = mode;
        mmc_set_ios(host);
}

/*
 * Sets the host clock to the highest possible frequency that
 * is below "hz".
 */
void mmc_set_clock(struct mmc_host *host, unsigned int hz)
{
        WARN_ON(hz && hz < host->f_min);

        if (hz > host->f_max)
                hz = host->f_max;

        host->ios.clock = hz;
        mmc_set_ios(host);
}

int mmc_execute_tuning(struct mmc_card *card)
{
        struct mmc_host *host = card->host;
        u32 opcode;
        int err;

        if (!host->ops->execute_tuning)
                return 0;

        if (host->cqe_on)
                host->cqe_ops->cqe_off(host);

        if (mmc_card_mmc(card))
                opcode = MMC_SEND_TUNING_BLOCK_HS200;
        else
                opcode = MMC_SEND_TUNING_BLOCK;

        err = host->ops->execute_tuning(host, opcode);

        if (err)
                pr_err("%s: tuning execution failed: %d\n",
                        mmc_hostname(host), err);
        else
                mmc_retune_enable(host);

        return err;
}

/*
 * Change the bus mode (open drain/push-pull) of a host.
 */
void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode)
{
        host->ios.bus_mode = mode;
        mmc_set_ios(host);
}

/*
 * Change data bus width of a host.
 */
void mmc_set_bus_width(struct mmc_host *host, unsigned int width)
{
        host->ios.bus_width = width;
        mmc_set_ios(host);
}

/*
 * Set initial state after a power cycle or a hw_reset.
 */
void mmc_set_initial_state(struct mmc_host *host)
{
        if (host->cqe_on)
                host->cqe_ops->cqe_off(host);

        mmc_retune_disable(host);

        if (mmc_host_is_spi(host))
                host->ios.chip_select = MMC_CS_HIGH;
        else
                host->ios.chip_select = MMC_CS_DONTCARE;
        host->ios.bus_mode = MMC_BUSMODE_PUSHPULL;
        host->ios.bus_width = MMC_BUS_WIDTH_1;
        host->ios.timing = MMC_TIMING_LEGACY;
        host->ios.drv_type = 0;
        host->ios.enhanced_strobe = false;

        /*
         * Make sure we are in non-enhanced strobe mode before we
         * actually enable it in ext_csd.
         */
        if ((host->caps2 & MMC_CAP2_HS400_ES) &&
             host->ops->hs400_enhanced_strobe)
                host->ops->hs400_enhanced_strobe(host, &host->ios);

        mmc_set_ios(host);
}

/**
 * mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number
 * @vdd:        voltage (mV)
 * @low_bits:   prefer low bits in boundary cases
 *
 * This function returns the OCR bit number according to the provided @vdd
 * value. If conversion is not possible a negative errno value returned.
 *
 * Depending on the @low_bits flag the function prefers low or high OCR bits
 * on boundary voltages. For example,
 * with @low_bits = true, 3300 mV translates to ilog2(MMC_VDD_32_33);
 * with @low_bits = false, 3300 mV translates to ilog2(MMC_VDD_33_34);
 *
 * Any value in the [1951:1999] range translates to the ilog2(MMC_VDD_20_21).
 */
static int mmc_vdd_to_ocrbitnum(int vdd, bool low_bits)
{
        const int max_bit = ilog2(MMC_VDD_35_36);
        int bit;

        if (vdd < 1650 || vdd > 3600)
                return -EINVAL;

        if (vdd >= 1650 && vdd <= 1950)
                return ilog2(MMC_VDD_165_195);

        if (low_bits)
                vdd -= 1;

        /* Base 2000 mV, step 100 mV, bit's base 8. */
        bit = (vdd - 2000) / 100 + 8;
        if (bit > max_bit)
                return max_bit;
        return bit;
}

/**
 * mmc_vddrange_to_ocrmask - Convert a voltage range to the OCR mask
 * @vdd_min:    minimum voltage value (mV)
 * @vdd_max:    maximum voltage value (mV)
 *
 * This function returns the OCR mask bits according to the provided @vdd_min
 * and @vdd_max values. If conversion is not possible the function returns 0.
 *
 * Notes wrt boundary cases:
 * This function sets the OCR bits for all boundary voltages, for example
 * [3300:3400] range is translated to MMC_VDD_32_33 | MMC_VDD_33_34 |
 * MMC_VDD_34_35 mask.
 */
u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max)
{
        u32 mask = 0;

        if (vdd_max < vdd_min)
                return 0;

        /* Prefer high bits for the boundary vdd_max values. */
        vdd_max = mmc_vdd_to_ocrbitnum(vdd_max, false);
        if (vdd_max < 0)
                return 0;

        /* Prefer low bits for the boundary vdd_min values. */
        vdd_min = mmc_vdd_to_ocrbitnum(vdd_min, true);
        if (vdd_min < 0)
                return 0;

        /* Fill the mask, from max bit to min bit. */
        while (vdd_max >= vdd_min)
                mask |= 1 << vdd_max--;

        return mask;
}
EXPORT_SYMBOL(mmc_vddrange_to_ocrmask);

#ifdef CONFIG_OF

/**
 * mmc_of_parse_voltage - return mask of supported voltages
 * @np: The device node need to be parsed.
 * @mask: mask of voltages available for MMC/SD/SDIO
 *
 * Parse the "voltage-ranges" DT property, returning zero if it is not
 * found, negative errno if the voltage-range specification is invalid,
 * or one if the voltage-range is specified and successfully parsed.
 */
int mmc_of_parse_voltage(struct device_node *np, u32 *mask)
{
        const u32 *voltage_ranges;
        int num_ranges, i;

        voltage_ranges = of_get_property(np, "voltage-ranges", &num_ranges);
        num_ranges = num_ranges / sizeof(*voltage_ranges) / 2;
        if (!voltage_ranges) {
                pr_debug("%pOF: voltage-ranges unspecified\n", np);
                return 0;
        }
        if (!num_ranges) {
                pr_err("%pOF: voltage-ranges empty\n", np);
                return -EINVAL;
        }

        for (i = 0; i < num_ranges; i++) {
                const int j = i * 2;
                u32 ocr_mask;

                ocr_mask = mmc_vddrange_to_ocrmask(
                                be32_to_cpu(voltage_ranges[j]),
                                be32_to_cpu(voltage_ranges[j + 1]));
                if (!ocr_mask) {
                        pr_err("%pOF: voltage-range #%d is invalid\n",
                                np, i);
                        return -EINVAL;
                }
                *mask |= ocr_mask;
        }

        return 1;
}
EXPORT_SYMBOL(mmc_of_parse_voltage);

#endif /* CONFIG_OF */

static int mmc_of_get_func_num(struct device_node *node)
{
        u32 reg;
        int ret;

        ret = of_property_read_u32(node, "reg", &reg);
        if (ret < 0)
                return ret;

        return reg;
}

struct device_node *mmc_of_find_child_device(struct mmc_host *host,
                unsigned func_num)
{
        struct device_node *node;

        if (!host->parent || !host->parent->of_node)
                return NULL;

        for_each_child_of_node(host->parent->of_node, node) {
                if (mmc_of_get_func_num(node) == func_num)
                        return node;
        }

        return NULL;
}

#ifdef CONFIG_REGULATOR

/**
 * mmc_ocrbitnum_to_vdd - Convert a OCR bit number to its voltage
 * @vdd_bit:    OCR bit number
 * @min_uV:     minimum voltage value (mV)
 * @max_uV:     maximum voltage value (mV)
 *
 * This function returns the voltage range according to the provided OCR
 * bit number. If conversion is not possible a negative errno value returned.
 */
static int mmc_ocrbitnum_to_vdd(int vdd_bit, int *min_uV, int *max_uV)
{
        int             tmp;

        if (!vdd_bit)
                return -EINVAL;

        /*
         * REVISIT mmc_vddrange_to_ocrmask() may have set some
         * bits this regulator doesn't quite support ... don't
         * be too picky, most cards and regulators are OK with
         * a 0.1V range goof (it's a small error percentage).
         */
        tmp = vdd_bit - ilog2(MMC_VDD_165_195);
        if (tmp == 0) {
                *min_uV = 1650 * 1000;
                *max_uV = 1950 * 1000;
        } else {
                *min_uV = 1900 * 1000 + tmp * 100 * 1000;
                *max_uV = *min_uV + 100 * 1000;
        }

        return 0;
}

/**
 * mmc_regulator_get_ocrmask - return mask of supported voltages
 * @supply: regulator to use
 *
 * This returns either a negative errno, or a mask of voltages that
 * can be provided to MMC/SD/SDIO devices using the specified voltage
 * regulator.  This would normally be called before registering the
 * MMC host adapter.
 */
int mmc_regulator_get_ocrmask(struct regulator *supply)
{
        int                     result = 0;
        int                     count;
        int                     i;
        int                     vdd_uV;
        int                     vdd_mV;

        count = regulator_count_voltages(supply);
        if (count < 0)
                return count;

        for (i = 0; i < count; i++) {
                vdd_uV = regulator_list_voltage(supply, i);
                if (vdd_uV <= 0)
                        continue;

                vdd_mV = vdd_uV / 1000;
                result |= mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV);
        }

        if (!result) {
                vdd_uV = regulator_get_voltage(supply);
                if (vdd_uV <= 0)
                        return vdd_uV;

                vdd_mV = vdd_uV / 1000;
                result = mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV);
        }

        return result;
}
EXPORT_SYMBOL_GPL(mmc_regulator_get_ocrmask);

/**
 * mmc_regulator_set_ocr - set regulator to match host->ios voltage
 * @mmc: the host to regulate
 * @supply: regulator to use
 * @vdd_bit: zero for power off, else a bit number (host->ios.vdd)
 *
 * Returns zero on success, else negative errno.
 *
 * MMC host drivers may use this to enable or disable a regulator using
 * a particular supply voltage.  This would normally be called from the
 * set_ios() method.
 */
int mmc_regulator_set_ocr(struct mmc_host *mmc,
                        struct regulator *supply,
                        unsigned short vdd_bit)
{
        int                     result = 0;
        int                     min_uV, max_uV;

        if (vdd_bit) {
                mmc_ocrbitnum_to_vdd(vdd_bit, &min_uV, &max_uV);

                result = regulator_set_voltage(supply, min_uV, max_uV);
                if (result == 0 && !mmc->regulator_enabled) {
                        result = regulator_enable(supply);
                        if (!result)
                                mmc->regulator_enabled = true;
                }
        } else if (mmc->regulator_enabled) {
                result = regulator_disable(supply);
                if (result == 0)
                        mmc->regulator_enabled = false;
        }

        if (result)
                dev_err(mmc_dev(mmc),
                        "could not set regulator OCR (%d)\n", result);
        return result;
}
EXPORT_SYMBOL_GPL(mmc_regulator_set_ocr);

static int mmc_regulator_set_voltage_if_supported(struct regulator *regulator,
                                                  int min_uV, int target_uV,
                                                  int max_uV)
{
        /*
         * Check if supported first to avoid errors since we may try several
         * signal levels during power up and don't want to show errors.
         */
        if (!regulator_is_supported_voltage(regulator, min_uV, max_uV))
                return -EINVAL;

        return regulator_set_voltage_triplet(regulator, min_uV, target_uV,
                                             max_uV);
}

/**
 * mmc_regulator_set_vqmmc - Set VQMMC as per the ios
 *
 * For 3.3V signaling, we try to match VQMMC to VMMC as closely as possible.
 * That will match the behavior of old boards where VQMMC and VMMC were supplied
 * by the same supply.  The Bus Operating conditions for 3.3V signaling in the
 * SD card spec also define VQMMC in terms of VMMC.
 * If this is not possible we'll try the full 2.7-3.6V of the spec.
 *
 * For 1.2V and 1.8V signaling we'll try to get as close as possible to the
 * requested voltage.  This is definitely a good idea for UHS where there's a
 * separate regulator on the card that's trying to make 1.8V and it's best if
 * we match.
 *
 * This function is expected to be used by a controller's
 * start_signal_voltage_switch() function.
 */
int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios)
{
        struct device *dev = mmc_dev(mmc);
        int ret, volt, min_uV, max_uV;

        /* If no vqmmc supply then we can't change the voltage */
        if (IS_ERR(mmc->supply.vqmmc))
                return -EINVAL;

        switch (ios->signal_voltage) {
        case MMC_SIGNAL_VOLTAGE_120:
                return mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc,
                                                1100000, 1200000, 1300000);
        case MMC_SIGNAL_VOLTAGE_180:
                return mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc,
                                                1700000, 1800000, 1950000);
        case MMC_SIGNAL_VOLTAGE_330:
                ret = mmc_ocrbitnum_to_vdd(mmc->ios.vdd, &volt, &max_uV);
                if (ret < 0)
                        return ret;

                dev_dbg(dev, "%s: found vmmc voltage range of %d-%duV\n",
                        __func__, volt, max_uV);

                min_uV = max(volt - 300000, 2700000);
                max_uV = min(max_uV + 200000, 3600000);

                /*
                 * Due to a limitation in the current implementation of
                 * regulator_set_voltage_triplet() which is taking the lowest
                 * voltage possible if below the target, search for a suitable
                 * voltage in two steps and try to stay close to vmmc
                 * with a 0.3V tolerance at first.
                 */
                if (!mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc,
                                                min_uV, volt, max_uV))
                        return 0;

                return mmc_regulator_set_voltage_if_supported(mmc->supply.vqmmc,
                                                2700000, volt, 3600000);
        default:
                return -EINVAL;
        }
}
EXPORT_SYMBOL_GPL(mmc_regulator_set_vqmmc);

#endif /* CONFIG_REGULATOR */

int mmc_regulator_get_supply(struct mmc_host *mmc)
{
        struct device *dev = mmc_dev(mmc);
        int ret;

        mmc->supply.vmmc = devm_regulator_get_optional(dev, "vmmc");
        mmc->supply.vqmmc = devm_regulator_get_optional(dev, "vqmmc");

        if (IS_ERR(mmc->supply.vmmc)) {
                if (PTR_ERR(mmc->supply.vmmc) == -EPROBE_DEFER)
                        return -EPROBE_DEFER;
                dev_dbg(dev, "No vmmc regulator found\n");
        } else {
                ret = mmc_regulator_get_ocrmask(mmc->supply.vmmc);
                if (ret > 0)
                        mmc->ocr_avail = ret;
                else
                        dev_warn(dev, "Failed getting OCR mask: %d\n", ret);
        }

        if (IS_ERR(mmc->supply.vqmmc)) {
                if (PTR_ERR(mmc->supply.vqmmc) == -EPROBE_DEFER)
                        return -EPROBE_DEFER;
                dev_dbg(dev, "No vqmmc regulator found\n");
        }

        return 0;
}
EXPORT_SYMBOL_GPL(mmc_regulator_get_supply);

/*
 * Mask off any voltages we don't support and select
 * the lowest voltage
 */
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
{
        int bit;

        /*
         * Sanity check the voltages that the card claims to
         * support.
         */
        if (ocr & 0x7F) {
                dev_warn(mmc_dev(host),
                "card claims to support voltages below defined range\n");
                ocr &= ~0x7F;
        }

        ocr &= host->ocr_avail;
        if (!ocr) {
                dev_warn(mmc_dev(host), "no support for card's volts\n");
                return 0;
        }

        if (host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) {
                bit = ffs(ocr) - 1;
                ocr &= 3 << bit;
                mmc_power_cycle(host, ocr);
        } else {
                bit = fls(ocr) - 1;
                ocr &= 3 << bit;
                if (bit != host->ios.vdd)
                        dev_warn(mmc_dev(host), "exceeding card's volts\n");
        }

        return ocr;
}

int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
{
        int err = 0;
        int old_signal_voltage = host->ios.signal_voltage;

        host->ios.signal_voltage = signal_voltage;
        if (host->ops->start_signal_voltage_switch)
                err = host->ops->start_signal_voltage_switch(host, &host->ios);

        if (err)
                host->ios.signal_voltage = old_signal_voltage;

        return err;

}

int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr)
{
        struct mmc_command cmd = {};
        int err = 0;
        u32 clock;

        /*
         * If we cannot switch voltages, return failure so the caller
         * can continue without UHS mode
         */
        if (!host->ops->start_signal_voltage_switch)
                return -EPERM;
        if (!host->ops->card_busy)
                pr_warn("%s: cannot verify signal voltage switch\n",
                        mmc_hostname(host));

        cmd.opcode = SD_SWITCH_VOLTAGE;
        cmd.arg = 0;
        cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;

        err = mmc_wait_for_cmd(host, &cmd, 0);
        if (err)
                return err;

        if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
                return -EIO;

        /*
         * The card should drive cmd and dat[0:3] low immediately
         * after the response of cmd11, but wait 1 ms to be sure
         */
        mmc_delay(1);
        if (host->ops->card_busy && !host->ops->card_busy(host)) {
                err = -EAGAIN;
                goto power_cycle;
        }
        /*
         * During a signal voltage level switch, the clock must be gated
         * for 5 ms according to the SD spec
         */
        clock = host->ios.clock;
        host->ios.clock = 0;
        mmc_set_ios(host);

        if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180)) {
                /*
                 * Voltages may not have been switched, but we've already
                 * sent CMD11, so a power cycle is required anyway
                 */
                err = -EAGAIN;
                goto power_cycle;
        }

        /* Keep clock gated for at least 10 ms, though spec only says 5 ms */
        mmc_delay(10);
        host->ios.clock = clock;
        mmc_set_ios(host);

        /* Wait for at least 1 ms according to spec */
        mmc_delay(1);

        /*
         * Failure to switch is indicated by the card holding
         * dat[0:3] low
         */
        if (host->ops->card_busy && host->ops->card_busy(host))
                err = -EAGAIN;

power_cycle:
        if (err) {
                pr_debug("%s: Signal voltage switch failed, "
                        "power cycling card\n", mmc_hostname(host));
                mmc_power_cycle(host, ocr);
        }

        return err;
}

/*
 * Select timing parameters for host.
 */
void mmc_set_timing(struct mmc_host *host, unsigned int timing)
{
        host->ios.timing = timing;
        mmc_set_ios(host);
}

/*
 * Select appropriate driver type for host.
 */
void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type)
{
        host->ios.drv_type = drv_type;
        mmc_set_ios(host);
}

int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr,
                              int card_drv_type, int *drv_type)
{
        struct mmc_host *host = card->host;
        int host_drv_type = SD_DRIVER_TYPE_B;

        *drv_type = 0;

        if (!host->ops->select_drive_strength)
                return 0;

        /* Use SD definition of driver strength for hosts */
        if (host->caps & MMC_CAP_DRIVER_TYPE_A)
                host_drv_type |= SD_DRIVER_TYPE_A;

        if (host->caps & MMC_CAP_DRIVER_TYPE_C)
                host_drv_type |= SD_DRIVER_TYPE_C;

        if (host->caps & MMC_CAP_DRIVER_TYPE_D)
                host_drv_type |= SD_DRIVER_TYPE_D;

        /*
         * The drive strength that the hardware can support
         * depends on the board design.  Pass the appropriate
         * information and let the hardware specific code
         * return what is possible given the options
         */
        return host->ops->select_drive_strength(card, max_dtr,
                                                host_drv_type,
                                                card_drv_type,
                                                drv_type);
}

/*
 * Apply power to the MMC stack.  This is a two-stage process.
 * First, we enable power to the card without the clock running.
 * We then wait a bit for the power to stabilise.  Finally,
 * enable the bus drivers and clock to the card.
 *
 * We must _NOT_ enable the clock prior to power stablising.
 *
 * If a host does all the power sequencing itself, ignore the
 * initial MMC_POWER_UP stage.
 */
void mmc_power_up(struct mmc_host *host, u32 ocr)
{
        if (host->ios.power_mode == MMC_POWER_ON)
                return;

        mmc_pwrseq_pre_power_on(host);

        host->ios.vdd = fls(ocr) - 1;
        host->ios.power_mode = MMC_POWER_UP;
        /* Set initial state and call mmc_set_ios */
        mmc_set_initial_state(host);

        /* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */
        if (!mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330))
                dev_dbg(mmc_dev(host), "Initial signal voltage of 3.3v\n");
        else if (!mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180))
                dev_dbg(mmc_dev(host), "Initial signal voltage of 1.8v\n");
        else if (!mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120))
                dev_dbg(mmc_dev(host), "Initial signal voltage of 1.2v\n");

        /*
         * This delay should be sufficient to allow the power supply
         * to reach the minimum voltage.
         */
        mmc_delay(10);

        mmc_pwrseq_post_power_on(host);

        host->ios.clock = host->f_init;

        host->ios.power_mode = MMC_POWER_ON;
        mmc_set_ios(host);

        /*
         * This delay must be at least 74 clock sizes, or 1 ms, or the
         * time required to reach a stable voltage.
         */
        mmc_delay(10);
}

void mmc_power_off(struct mmc_host *host)
{
        if (host->ios.power_mode == MMC_POWER_OFF)
                return;

        mmc_pwrseq_power_off(host);

        host->ios.clock = 0;
        host->ios.vdd = 0;

        host->ios.power_mode = MMC_POWER_OFF;
        /* Set initial state and call mmc_set_ios */
        mmc_set_initial_state(host);

        /*
         * Some configurations, such as the 802.11 SDIO card in the OLPC
         * XO-1.5, require a short delay after poweroff before the card
         * can be successfully turned on again.
         */
        mmc_delay(1);
}

void mmc_power_cycle(struct mmc_host *host, u32 ocr)
{
        mmc_power_off(host);
        /* Wait at least 1 ms according to SD spec */
        mmc_delay(1);
        mmc_power_up(host, ocr);
}

/*
 * Cleanup when the last reference to the bus operator is dropped.
 */
static void __mmc_release_bus(struct mmc_host *host)
{
        WARN_ON(!host->bus_dead);

        host->bus_ops = NULL;
}

/*
 * Increase reference count of bus operator
 */
static inline void mmc_bus_get(struct mmc_host *host)
{
        unsigned long flags;

        spin_lock_irqsave(&host->lock, flags);
        host->bus_refs++;
        spin_unlock_irqrestore(&host->lock, flags);
}

/*
 * Decrease reference count of bus operator and free it if
 * it is the last reference.
 */
static inline void mmc_bus_put(struct mmc_host *host)
{
        unsigned long flags;

        spin_lock_irqsave(&host->lock, flags);
        host->bus_refs--;
        if ((host->bus_refs == 0) && host->bus_ops)
                __mmc_release_bus(host);
        spin_unlock_irqrestore(&host->lock, flags);
}

/*
 * Assign a mmc bus handler to a host. Only one bus handler may control a
 * host at any given time.
 */
void mmc_attach_bus(struct mmc_host *host, const struct mmc_bus_ops *ops)
{
        unsigned long flags;

        WARN_ON(!host->claimed);

        spin_lock_irqsave(&host->lock, flags);

        WARN_ON(host->bus_ops);
        WARN_ON(host->bus_refs);

        host->bus_ops = ops;
        host->bus_refs = 1;
        host->bus_dead = 0;

        spin_unlock_irqrestore(&host->lock, flags);
}

/*
 * Remove the current bus handler from a host.
 */
void mmc_detach_bus(struct mmc_host *host)
{
        unsigned long flags;

        WARN_ON(!host->claimed);
        WARN_ON(!host->bus_ops);

        spin_lock_irqsave(&host->lock, flags);

        host->bus_dead = 1;

        spin_unlock_irqrestore(&host->lock, flags);

        mmc_bus_put(host);
}

static void _mmc_detect_change(struct mmc_host *host, unsigned long delay,
                                bool cd_irq)
{
        /*
         * If the device is configured as wakeup, we prevent a new sleep for
         * 5 s to give provision for user space to consume the event.
         */
        if (cd_irq && !(host->caps & MMC_CAP_NEEDS_POLL) &&
                device_can_wakeup(mmc_dev(host)))
                pm_wakeup_event(mmc_dev(host), 5000);

        host->detect_change = 1;
        mmc_schedule_delayed_work(&host->detect, delay);
}

/**
 *      mmc_detect_change - process change of state on a MMC socket
 *      @host: host which changed state.
 *      @delay: optional delay to wait before detection (jiffies)
 *
 *      MMC drivers should call this when they detect a card has been
 *      inserted or removed. The MMC layer will confirm that any
 *      present card is still functional, and initialize any newly
 *      inserted.
 */
void mmc_detect_change(struct mmc_host *host, unsigned long delay)
{
        _mmc_detect_change(host, delay, true);
}
EXPORT_SYMBOL(mmc_detect_change);

void mmc_init_erase(struct mmc_card *card)
{
        unsigned int sz;

        if (is_power_of_2(card->erase_size))
                card->erase_shift = ffs(card->erase_size) - 1;
        else
                card->erase_shift = 0;

        /*
         * It is possible to erase an arbitrarily large area of an SD or MMC
         * card.  That is not desirable because it can take a long time
         * (minutes) potentially delaying more important I/O, and also the
         * timeout calculations become increasingly hugely over-estimated.
         * Consequently, 'pref_erase' is defined as a guide to limit erases
         * to that size and alignment.
         *
         * For SD cards that define Allocation Unit size, limit erases to one
         * Allocation Unit at a time.
         * For MMC, have a stab at ai good value and for modern cards it will
         * end up being 4MiB. Note that if the value is too small, it can end
         * up taking longer to erase. Also note, erase_size is already set to
         * High Capacity Erase Size if available when this function is called.
         */
        if (mmc_card_sd(card) && card->ssr.au) {
                card->pref_erase = card->ssr.au;
                card->erase_shift = ffs(card->ssr.au) - 1;
        } else if (card->erase_size) {
                sz = (card->csd.capacity << (card->csd.read_blkbits - 9)) >> 11;
                if (sz < 128)
                        card->pref_erase = 512 * 1024 / 512;
                else if (sz < 512)
                        card->pref_erase = 1024 * 1024 / 512;
                else if (sz < 1024)
                        card->pref_erase = 2 * 1024 * 1024 / 512;
                else
                        card->pref_erase = 4 * 1024 * 1024 / 512;
                if (card->pref_erase < card->erase_size)
                        card->pref_erase = card->erase_size;
                else {
                        sz = card->pref_erase % card->erase_size;
                        if (sz)
                                card->pref_erase += card->erase_size - sz;
                }
        } else
                card->pref_erase = 0;
}

static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card,
                                          unsigned int arg, unsigned int qty)
{
        unsigned int erase_timeout;

        if (arg == MMC_DISCARD_ARG ||
            (arg == MMC_TRIM_ARG && card->ext_csd.rev >= 6)) {
                erase_timeout = card->ext_csd.trim_timeout;
        } else if (card->ext_csd.erase_group_def & 1) {
                /* High Capacity Erase Group Size uses HC timeouts */
                if (arg == MMC_TRIM_ARG)
                        erase_timeout = card->ext_csd.trim_timeout;
                else
                        erase_timeout = card->ext_csd.hc_erase_timeout;
        } else {
                /* CSD Erase Group Size uses write timeout */
                unsigned int mult = (10 << card->csd.r2w_factor);
                unsigned int timeout_clks = card->csd.taac_clks * mult;
                unsigned int timeout_us;

                /* Avoid overflow: e.g. taac_ns=80000000 mult=1280 */
                if (card->csd.taac_ns < 1000000)
                        timeout_us = (card->csd.taac_ns * mult) / 1000;
                else
                        timeout_us = (card->csd.taac_ns / 1000) * mult;

                /*
                 * ios.clock is only a target.  The real clock rate might be
                 * less but not that much less, so fudge it by multiplying by 2.
                 */
                timeout_clks <<= 1;
                timeout_us += (timeout_clks * 1000) /
                              (card->host->ios.clock / 1000);

                erase_timeout = timeout_us / 1000;

                /*
                 * Theoretically, the calculation could underflow so round up
                 * to 1ms in that case.
                 */
                if (!erase_timeout)
                        erase_timeout = 1;
        }

        /* Multiplier for secure operations */
        if (arg & MMC_SECURE_ARGS) {
                if (arg == MMC_SECURE_ERASE_ARG)
                        erase_timeout *= card->ext_csd.sec_erase_mult;
                else
                        erase_timeout *= card->ext_csd.sec_trim_mult;
        }

        erase_timeout *= qty;

        /*
         * Ensure at least a 1 second timeout for SPI as per
         * 'mmc_set_data_timeout()'
         */
        if (mmc_host_is_spi(card->host) && erase_timeout < 1000)
                erase_timeout = 1000;

        return erase_timeout;
}

static unsigned int mmc_sd_erase_timeout(struct mmc_card *card,
                                         unsigned int arg,
                                         unsigned int qty)
{
        unsigned int erase_timeout;

        if (card->ssr.erase_timeout) {
                /* Erase timeout specified in SD Status Register (SSR) */
                erase_timeout = card->ssr.erase_timeout * qty +
                                card->ssr.erase_offset;
        } else {
                /*
                 * Erase timeout not specified in SD Status Register (SSR) so
                 * use 250ms per write block.
                 */
                erase_timeout = 250 * qty;
        }

        /* Must not be less than 1 second */
        if (erase_timeout < 1000)
                erase_timeout = 1000;

        return erase_timeout;
}

static unsigned int mmc_erase_timeout(struct mmc_card *card,
                                      unsigned int arg,
                                      unsigned int qty)
{
        if (mmc_card_sd(card))
                return mmc_sd_erase_timeout(card, arg, qty);
        else
                return mmc_mmc_erase_timeout(card, arg, qty);
}

static int mmc_do_erase(struct mmc_card *card, unsigned int from,
                        unsigned int to, unsigned int arg)
{
        struct mmc_command cmd = {};
        unsigned int qty = 0, busy_timeout = 0;
        bool use_r1b_resp = false;
        unsigned long timeout;
        int err;

        mmc_retune_hold(card->host);

        /*
         * qty is used to calculate the erase timeout which depends on how many
         * erase groups (or allocation units in SD terminology) are affected.
         * We count erasing part of an erase group as one erase group.
         * For SD, the allocation units are always a power of 2.  For MMC, the
         * erase group size is almost certainly also power of 2, but it does not
         * seem to insist on that in the JEDEC standard, so we fall back to
         * division in that case.  SD may not specify an allocation unit size,
         * in which case the timeout is based on the number of write blocks.
         *
         * Note that the timeout for secure trim 2 will only be correct if the
         * number of erase groups specified is the same as the total of all
         * preceding secure trim 1 commands.  Since the power may have been
         * lost since the secure trim 1 commands occurred, it is generally
         * impossible to calculate the secure trim 2 timeout correctly.
         */
        if (card->erase_shift)
                qty += ((to >> card->erase_shift) -
                        (from >> card->erase_shift)) + 1;
        else if (mmc_card_sd(card))
                qty += to - from + 1;
        else
                qty += ((to / card->erase_size) -
                        (from / card->erase_size)) + 1;

        if (!mmc_card_blockaddr(card)) {
                from <<= 9;
                to <<= 9;
        }

        if (mmc_card_sd(card))
                cmd.opcode = SD_ERASE_WR_BLK_START;
        else
                cmd.opcode = MMC_ERASE_GROUP_START;
        cmd.arg = from;
        cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
        err = mmc_wait_for_cmd(card->host, &cmd, 0);
        if (err) {
                pr_err("mmc_erase: group start error %d, "
                       "status %#x\n", err, cmd.resp[0]);
                err = -EIO;
                goto out;
        }

        memset(&cmd, 0, sizeof(struct mmc_command));
        if (mmc_card_sd(card))
                cmd.opcode = SD_ERASE_WR_BLK_END;
        else
                cmd.opcode = MMC_ERASE_GROUP_END;
        cmd.arg = to;
        cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
        err = mmc_wait_for_cmd(card->host, &cmd, 0);
        if (err) {
                pr_err("mmc_erase: group end error %d, status %#x\n",
                       err, cmd.resp[0]);
                err = -EIO;
                goto out;
        }

        memset(&cmd, 0, sizeof(struct mmc_command));
        cmd.opcode = MMC_ERASE;
        cmd.arg = arg;
        busy_timeout = mmc_erase_timeout(card, arg, qty);
        /*
         * If the host controller supports busy signalling and the timeout for
         * the erase operation does not exceed the max_busy_timeout, we should
         * use R1B response. Or we need to prevent the host from doing hw busy
         * detection, which is done by converting to a R1 response instead.
         */
        if (card->host->max_busy_timeout &&
            busy_timeout > card->host->max_busy_timeout) {
                cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
        } else {
                cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
                cmd.busy_timeout = busy_timeout;
                use_r1b_resp = true;
        }

        err = mmc_wait_for_cmd(card->host, &cmd, 0);
        if (err) {
                pr_err("mmc_erase: erase error %d, status %#x\n",
                       err, cmd.resp[0]);
                err = -EIO;
                goto out;
        }

        if (mmc_host_is_spi(card->host))
                goto out;

        /*
         * In case of when R1B + MMC_CAP_WAIT_WHILE_BUSY is used, the polling
         * shall be avoided.
         */
        if ((card->host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp)
                goto out;

        timeout = jiffies + msecs_to_jiffies(busy_timeout);
        do {
                memset(&cmd, 0, sizeof(struct mmc_command));
                cmd.opcode = MMC_SEND_STATUS;
                cmd.arg = card->rca << 16;
                cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
                /* Do not retry else we can't see errors */
                err = mmc_wait_for_cmd(card->host, &cmd, 0);
                if (err || (cmd.resp[0] & 0xFDF92000)) {
                        pr_err("error %d requesting status %#x\n",
                                err, cmd.resp[0]);
                        err = -EIO;
                        goto out;
                }

                /* Timeout if the device never becomes ready for data and
                 * never leaves the program state.
                 */
                if (time_after(jiffies, timeout)) {
                        pr_err("%s: Card stuck in programming state! %s\n",
                                mmc_hostname(card->host), __func__);
                        err =  -EIO;
                        goto out;
                }

        } while (!(cmd.resp[0] & R1_READY_FOR_DATA) ||
                 (R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG));
out:
        mmc_retune_release(card->host);
        return err;
}

static unsigned int mmc_align_erase_size(struct mmc_card *card,
                                         unsigned int *from,
                                         unsigned int *to,
                                         unsigned int nr)
{
        unsigned int from_new = *from, nr_new = nr, rem;

        /*
         * When the 'card->erase_size' is power of 2, we can use round_up/down()
         * to align the erase size efficiently.
         */
        if (is_power_of_2(card->erase_size)) {
                unsigned int temp = from_new;

                from_new = round_up(temp, card->erase_size);
                rem = from_new - temp;

                if (nr_new > rem)
                        nr_new -= rem;
                else
                        return 0;

                nr_new = round_down(nr_new, card->erase_size);
        } else {
                rem = from_new % card->erase_size;
                if (rem) {
                        rem = card->erase_size - rem;
                        from_new += rem;
                        if (nr_new > rem)
                                nr_new -= rem;
                        else
                                return 0;
                }

                rem = nr_new % card->erase_size;
                if (rem)
                        nr_new -= rem;
        }

        if (nr_new == 0)
                return 0;

        *to = from_new + nr_new;
        *from = from_new;

        return nr_new;
}

/**
 * mmc_erase - erase sectors.
 * @card: card to erase
 * @from: first sector to erase
 * @nr: number of sectors to erase
 * @arg: erase command argument (SD supports only %MMC_ERASE_ARG)
 *
 * Caller must claim host before calling this function.
 */
int mmc_erase(struct mmc_card *card, unsigned int from, unsigned int nr,
              unsigned int arg)
{
        unsigned int rem, to = from + nr;
        int err;

        if (!(card->host->caps & MMC_CAP_ERASE) ||
            !(card->csd.cmdclass & CCC_ERASE))
                return -EOPNOTSUPP;

        if (!card->erase_size)
                return -EOPNOTSUPP;

        if (mmc_card_sd(card) && arg != MMC_ERASE_ARG)
                return -EOPNOTSUPP;

        if ((arg & MMC_SECURE_ARGS) &&
            !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN))
                return -EOPNOTSUPP;

        if ((arg & MMC_TRIM_ARGS) &&
            !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN))
                return -EOPNOTSUPP;

        if (arg == MMC_SECURE_ERASE_ARG) {
                if (from % card->erase_size || nr % card->erase_size)
                        return -EINVAL;
        }

        if (arg == MMC_ERASE_ARG)
                nr = mmc_align_erase_size(card, &from, &to, nr);

        if (nr == 0)
                return 0;

        if (to <= from)
                return -EINVAL;

        /* 'from' and 'to' are inclusive */
        to -= 1;

        /*
         * Special case where only one erase-group fits in the timeout budget:
         * If the region crosses an erase-group boundary on this particular
         * case, we will be trimming more than one erase-group which, does not
         * fit in the timeout budget of the controller, so we need to split it
         * and call mmc_do_erase() twice if necessary. This special case is
         * identified by the card->eg_boundary flag.
         */
        rem = card->erase_size - (from % card->erase_size);
        if ((arg & MMC_TRIM_ARGS) && (card->eg_boundary) && (nr > rem)) {
                err = mmc_do_erase(card, from, from + rem - 1, arg);
                from += rem;
                if ((err) || (to <= from))
                        return err;
        }

        return mmc_do_erase(card, from, to, arg);
}
EXPORT_SYMBOL(mmc_erase);

int mmc_can_erase(struct mmc_card *card)
{
        if ((card->host->caps & MMC_CAP_ERASE) &&
            (card->csd.cmdclass & CCC_ERASE) && card->erase_size)
                return 1;
        return 0;
}
EXPORT_SYMBOL(mmc_can_erase);

int mmc_can_trim(struct mmc_card *card)
{
        if ((card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN) &&
            (!(card->quirks & MMC_QUIRK_TRIM_BROKEN)))
                return 1;
        return 0;
}
EXPORT_SYMBOL(mmc_can_trim);

int mmc_can_discard(struct mmc_card *card)
{
        /*
         * As there's no way to detect the discard support bit at v4.5
         * use the s/w feature support filed.
         */
        if (card->ext_csd.feature_support & MMC_DISCARD_FEATURE)
                return 1;
        return 0;
}
EXPORT_SYMBOL(mmc_can_discard);

int mmc_can_sanitize(struct mmc_card *card)
{
        if (!mmc_can_trim(card) && !mmc_can_erase(card))
                return 0;
        if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_SANITIZE)
                return 1;
        return 0;
}
EXPORT_SYMBOL(mmc_can_sanitize);

int mmc_can_secure_erase_trim(struct mmc_card *card)
{
        if ((card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN) &&
            !(card->quirks & MMC_QUIRK_SEC_ERASE_TRIM_BROKEN))
                return 1;
        return 0;
}
EXPORT_SYMBOL(mmc_can_secure_erase_trim);

int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from,
                            unsigned int nr)
{
        if (!card->erase_size)
                return 0;
        if (from % card->erase_size || nr % card->erase_size)
                return 0;
        return 1;
}
EXPORT_SYMBOL(mmc_erase_group_aligned);

static unsigned int mmc_do_calc_max_discard(struct mmc_card *card,
                                            unsigned int arg)
{
        struct mmc_host *host = card->host;
        unsigned int max_discard, x, y, qty = 0, max_qty, min_qty, timeout;
        unsigned int last_timeout = 0;
        unsigned int max_busy_timeout = host->max_busy_timeout ?
                        host->max_busy_timeout : MMC_ERASE_TIMEOUT_MS;

        if (card->erase_shift) {
                max_qty = UINT_MAX >> card->erase_shift;
                min_qty = card->pref_erase >> card->erase_shift;
        } else if (mmc_card_sd(card)) {
                max_qty = UINT_MAX;
                min_qty = card->pref_erase;
        } else {
                max_qty = UINT_MAX / card->erase_size;
                min_qty = card->pref_erase / card->erase_size;
        }

        /*
         * We should not only use 'host->max_busy_timeout' as the limitation
         * when deciding the max discard sectors. We should set a balance value
         * to improve the erase speed, and it can not get too long timeout at
         * the same time.
         *
         * Here we set 'card->pref_erase' as the minimal discard sectors no
         * matter what size of 'host->max_busy_timeout', but if the
         * 'host->max_busy_timeout' is large enough for more discard sectors,
         * then we can continue to increase the max discard sectors until we
         * get a balance value. In cases when the 'host->max_busy_timeout'
         * isn't specified, use the default max erase timeout.
         */
        do {
                y = 0;
                for (x = 1; x && x <= max_qty && max_qty - x >= qty; x <<= 1) {
                        timeout = mmc_erase_timeout(card, arg, qty + x);

                        if (qty + x > min_qty && timeout > max_busy_timeout)
                                break;

                        if (timeout < last_timeout)
                                break;
                        last_timeout = timeout;
                        y = x;
                }
                qty += y;
        } while (y);

        if (!qty)
                return 0;

        /*
         * When specifying a sector range to trim, chances are we might cross
         * an erase-group boundary even if the amount of sectors is less than
         * one erase-group.
         * If we can only fit one erase-group in the controller timeout budget,
         * we have to care that erase-group boundaries are not crossed by a
         * single trim operation. We flag that special case with "eg_boundary".
         * In all other cases we can just decrement qty and pretend that we
         * always touch (qty + 1) erase-groups as a simple optimization.
         */
        if (qty == 1)
                card->eg_boundary = 1;
        else
                qty--;

        /* Convert qty to sectors */
        if (card->erase_shift)
                max_discard = qty << card->erase_shift;
        else if (mmc_card_sd(card))
                max_discard = qty + 1;
        else
                max_discard = qty * card->erase_size;

        return max_discard;
}

unsigned int mmc_calc_max_discard(struct mmc_card *card)
{
        struct mmc_host *host = card->host;
        unsigned int max_discard, max_trim;

        /*
         * Without erase_group_def set, MMC erase timeout depends on clock
         * frequence which can change.  In that case, the best choice is
         * just the preferred erase size.
         */
        if (mmc_card_mmc(card) && !(card->ext_csd.erase_group_def & 1))
                return card->pref_erase;

        max_discard = mmc_do_calc_max_discard(card, MMC_ERASE_ARG);
        if (mmc_can_trim(card)) {
                max_trim = mmc_do_calc_max_discard(card, MMC_TRIM_ARG);
                if (max_trim < max_discard)
                        max_discard = max_trim;
        } else if (max_discard < card->erase_size) {
                max_discard = 0;
        }
        pr_debug("%s: calculated max. discard sectors %u for timeout %u ms\n",
                mmc_hostname(host), max_discard, host->max_busy_timeout ?
                host->max_busy_timeout : MMC_ERASE_TIMEOUT_MS);
        return max_discard;
}
EXPORT_SYMBOL(mmc_calc_max_discard);

bool mmc_card_is_blockaddr(struct mmc_card *card)
{
        return card ? mmc_card_blockaddr(card) : false;
}
EXPORT_SYMBOL(mmc_card_is_blockaddr);

int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen)
{
        struct mmc_command cmd = {};

        if (mmc_card_blockaddr(card) || mmc_card_ddr52(card) ||
            mmc_card_hs400(card) || mmc_card_hs400es(card))
                return 0;

        cmd.opcode = MMC_SET_BLOCKLEN;
        cmd.arg = blocklen;
        cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
        return mmc_wait_for_cmd(card->host, &cmd, 5);
}
EXPORT_SYMBOL(mmc_set_blocklen);

int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount,
                        bool is_rel_write)
{
        struct mmc_command cmd = {};

        cmd.opcode = MMC_SET_BLOCK_COUNT;
        cmd.arg = blockcount & 0x0000FFFF;
        if (is_rel_write)
                cmd.arg |= 1 << 31;
        cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
        return mmc_wait_for_cmd(card->host, &cmd, 5);
}
EXPORT_SYMBOL(mmc_set_blockcount);

static void mmc_hw_reset_for_init(struct mmc_host *host)
{
        mmc_pwrseq_reset(host);

        if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset)
                return;
        host->ops->hw_reset(host);
}

int mmc_hw_reset(struct mmc_host *host)
{
        int ret;

        if (!host->card)
                return -EINVAL;

        mmc_bus_get(host);
        if (!host->bus_ops || host->bus_dead || !host->bus_ops->reset) {
                mmc_bus_put(host);
                return -EOPNOTSUPP;
        }

        ret = host->bus_ops->reset(host);
        mmc_bus_put(host);

        if (ret)
                pr_warn("%s: tried to reset card, got error %d\n",
                        mmc_hostname(host), ret);

        return ret;
}
EXPORT_SYMBOL(mmc_hw_reset);

static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
{
        host->f_init = freq;

        pr_debug("%s: %s: trying to init card at %u Hz\n",
                mmc_hostname(host), __func__, host->f_init);

        mmc_power_up(host, host->ocr_avail);

        /*
         * Some eMMCs (with VCCQ always on) may not be reset after power up, so
         * do a hardware reset if possible.
         */
        mmc_hw_reset_for_init(host);

        /*
         * sdio_reset sends CMD52 to reset card.  Since we do not know
         * if the card is being re-initialized, just send it.  CMD52
         * should be ignored by SD/eMMC cards.
         * Skip it if we already know that we do not support SDIO commands
         */
        if (!(host->caps2 & MMC_CAP2_NO_SDIO))
                sdio_reset(host);

        mmc_go_idle(host);

        if (!(host->caps2 & MMC_CAP2_NO_SD))
                mmc_send_if_cond(host, host->ocr_avail);

        /* Order's important: probe SDIO, then SD, then MMC */
        if (!(host->caps2 & MMC_CAP2_NO_SDIO))
                if (!mmc_attach_sdio(host))
                        return 0;

        if (!(host->caps2 & MMC_CAP2_NO_SD))
                if (!mmc_attach_sd(host))
                        return 0;

        if (!(host->caps2 & MMC_CAP2_NO_MMC))
                if (!mmc_attach_mmc(host))
                        return 0;

        mmc_power_off(host);
        return -EIO;
}

int _mmc_detect_card_removed(struct mmc_host *host)
{
        int ret;

        if (!host->card || mmc_card_removed(host->card))
                return 1;

        ret = host->bus_ops->alive(host);

        /*
         * Card detect status and alive check may be out of sync if card is
         * removed slowly, when card detect switch changes while card/slot
         * pads are still contacted in hardware (refer to "SD Card Mechanical
         * Addendum, Appendix C: Card Detection Switch"). So reschedule a
         * detect work 200ms later for this case.
         */
        if (!ret && host->ops->get_cd && !host->ops->get_cd(host)) {
                mmc_detect_change(host, msecs_to_jiffies(200));
                pr_debug("%s: card removed too slowly\n", mmc_hostname(host));
        }

        if (ret) {
                mmc_card_set_removed(host->card);
                pr_debug("%s: card remove detected\n", mmc_hostname(host));
        }

        return ret;
}

int mmc_detect_card_removed(struct mmc_host *host)
{
        struct mmc_card *card = host->card;
        int ret;

        WARN_ON(!host->claimed);

        if (!card)
                return 1;

        if (!mmc_card_is_removable(host))
                return 0;

        ret = mmc_card_removed(card);
        /*
         * The card will be considered unchanged unless we have been asked to
         * detect a change or host requires polling to provide card detection.
         */
        if (!host->detect_change && !(host->caps & MMC_CAP_NEEDS_POLL))
                return ret;

        host->detect_change = 0;
        if (!ret) {
                ret = _mmc_detect_card_removed(host);
                if (ret && (host->caps & MMC_CAP_NEEDS_POLL)) {
                        /*
                         * Schedule a detect work as soon as possible to let a
                         * rescan handle the card removal.
                         */
                        cancel_delayed_work(&host->detect);
                        _mmc_detect_change(host, 0, false);
                }
        }

        return ret;
}
EXPORT_SYMBOL(mmc_detect_card_removed);

void mmc_rescan(struct work_struct *work)
{
        struct mmc_host *host =
                container_of(work, struct mmc_host, detect.work);
        int i;

        if (host->rescan_disable)
                return;

        /* If there is a non-removable card registered, only scan once */
        if (!mmc_card_is_removable(host) && host->rescan_entered)
                return;
        host->rescan_entered = 1;

        if (host->trigger_card_event && host->ops->card_event) {
                mmc_claim_host(host);
                host->ops->card_event(host);
                mmc_release_host(host);
                host->trigger_card_event = false;
        }

        mmc_bus_get(host);

        /*
         * if there is a _removable_ card registered, check whether it is
         * still present
         */
        if (host->bus_ops && !host->bus_dead && mmc_card_is_removable(host))
                host->bus_ops->detect(host);

        host->detect_change = 0;

        /*
         * Let mmc_bus_put() free the bus/bus_ops if we've found that
         * the card is no longer present.
         */
        mmc_bus_put(host);
        mmc_bus_get(host);

        /* if there still is a card present, stop here */
        if (host->bus_ops != NULL) {
                mmc_bus_put(host);
                goto out;
        }

        /*
         * Only we can add a new handler, so it's safe to
         * release the lock here.
         */
        mmc_bus_put(host);

        mmc_claim_host(host);
        if (mmc_card_is_removable(host) && host->ops->get_cd &&
                        host->ops->get_cd(host) == 0) {
                mmc_power_off(host);
                mmc_release_host(host);
                goto out;
        }

        for (i = 0; i < ARRAY_SIZE(freqs); i++) {
                if (!mmc_rescan_try_freq(host, max(freqs[i], host->f_min)))
                        break;
                if (freqs[i] <= host->f_min)
                        break;
        }
        mmc_release_host(host);

 out:
        if (host->caps & MMC_CAP_NEEDS_POLL)
                mmc_schedule_delayed_work(&host->detect, HZ);
}

void mmc_start_host(struct mmc_host *host)
{
        host->f_init = max(freqs[0], host->f_min);
        host->rescan_disable = 0;
        host->ios.power_mode = MMC_POWER_UNDEFINED;

        if (!(host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP)) {
                mmc_claim_host(host);
                mmc_power_up(host, host->ocr_avail);
                mmc_release_host(host);
        }

        mmc_gpiod_request_cd_irq(host);
        _mmc_detect_change(host, 0, false);
}

void mmc_stop_host(struct mmc_host *host)
{
        if (host->slot.cd_irq >= 0) {
                if (host->slot.cd_wake_enabled)
                        disable_irq_wake(host->slot.cd_irq);
                disable_irq(host->slot.cd_irq);
        }

        host->rescan_disable = 1;
        cancel_delayed_work_sync(&host->detect);

        /* clear pm flags now and let card drivers set them as needed */
        host->pm_flags = 0;

        mmc_bus_get(host);
        if (host->bus_ops && !host->bus_dead) {
                /* Calling bus_ops->remove() with a claimed host can deadlock */
                host->bus_ops->remove(host);
                mmc_claim_host(host);
                mmc_detach_bus(host);
                mmc_power_off(host);
                mmc_release_host(host);
                mmc_bus_put(host);
                return;
        }
        mmc_bus_put(host);

        mmc_claim_host(host);
        mmc_power_off(host);
        mmc_release_host(host);
}

int mmc_power_save_host(struct mmc_host *host)
{
        int ret = 0;

        pr_debug("%s: %s: powering down\n", mmc_hostname(host), __func__);

        mmc_bus_get(host);

        if (!host->bus_ops || host->bus_dead) {
                mmc_bus_put(host);
                return -EINVAL;
        }

        if (host->bus_ops->power_save)
                ret = host->bus_ops->power_save(host);

        mmc_bus_put(host);

        mmc_power_off(host);

        return ret;
}
EXPORT_SYMBOL(mmc_power_save_host);

int mmc_power_restore_host(struct mmc_host *host)
{
        int ret;

        pr_debug("%s: %s: powering up\n", mmc_hostname(host), __func__);

        mmc_bus_get(host);

        if (!host->bus_ops || host->bus_dead) {
                mmc_bus_put(host);
                return -EINVAL;
        }

        mmc_power_up(host, host->card->ocr);
        ret = host->bus_ops->power_restore(host);

        mmc_bus_put(host);

        return ret;
}
EXPORT_SYMBOL(mmc_power_restore_host);

#ifdef CONFIG_PM_SLEEP
/* Do the card removal on suspend if card is assumed removeable
 * Do that in pm notifier while userspace isn't yet frozen, so we will be able
   to sync the card.
*/
static int mmc_pm_notify(struct notifier_block *notify_block,
                        unsigned long mode, void *unused)
{
        struct mmc_host *host = container_of(
                notify_block, struct mmc_host, pm_notify);
        unsigned long flags;
        int err = 0;

        switch (mode) {
        case PM_HIBERNATION_PREPARE:
        case PM_SUSPEND_PREPARE:
        case PM_RESTORE_PREPARE:
                spin_lock_irqsave(&host->lock, flags);
                host->rescan_disable = 1;
                spin_unlock_irqrestore(&host->lock, flags);
                cancel_delayed_work_sync(&host->detect);

                if (!host->bus_ops)
                        break;

                /* Validate prerequisites for suspend */
                if (host->bus_ops->pre_suspend)
                        err = host->bus_ops->pre_suspend(host);
                if (!err)
                        break;

                /* Calling bus_ops->remove() with a claimed host can deadlock */
                host->bus_ops->remove(host);
                mmc_claim_host(host);
                mmc_detach_bus(host);
                mmc_power_off(host);
                mmc_release_host(host);
                host->pm_flags = 0;
                break;

        case PM_POST_SUSPEND:
        case PM_POST_HIBERNATION:
        case PM_POST_RESTORE:

                spin_lock_irqsave(&host->lock, flags);
                host->rescan_disable = 0;
                spin_unlock_irqrestore(&host->lock, flags);
                _mmc_detect_change(host, 0, false);

        }

        return 0;
}

void mmc_register_pm_notifier(struct mmc_host *host)
{
        host->pm_notify.notifier_call = mmc_pm_notify;
        register_pm_notifier(&host->pm_notify);
}

void mmc_unregister_pm_notifier(struct mmc_host *host)
{
        unregister_pm_notifier(&host->pm_notify);
}
#endif

/**
 * mmc_init_context_info() - init synchronization context
 * @host: mmc host
 *
 * Init struct context_info needed to implement asynchronous
 * request mechanism, used by mmc core, host driver and mmc requests
 * supplier.
 */
void mmc_init_context_info(struct mmc_host *host)
{
        host->context_info.is_new_req = false;
        host->context_info.is_done_rcv = false;
        host->context_info.is_waiting_last_req = false;
        init_waitqueue_head(&host->context_info.wait);
}

static int __init mmc_init(void)
{
        int ret;

        ret = mmc_register_bus();
        if (ret)
                return ret;

        ret = mmc_register_host_class();
        if (ret)
                goto unregister_bus;

        ret = sdio_register_bus();
        if (ret)
                goto unregister_host_class;

        return 0;

unregister_host_class:
        mmc_unregister_host_class();
unregister_bus:
        mmc_unregister_bus();
        return ret;
}

static void __exit mmc_exit(void)
{
        sdio_unregister_bus();
        mmc_unregister_host_class();
        mmc_unregister_bus();
}

subsys_initcall(mmc_init);
module_exit(mmc_exit);

MODULE_LICENSE("GPL");