drivers/ddr/fsl/lc_common_dimm_params.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright 2008-2016 Freescale Semiconductor, Inc.
   4  * Copyright 2017-2018 NXP Semiconductor
   5  */
   6
   7 #include <common.h>
   8 #include <fsl_ddr_sdram.h>
   9 #include <log.h>
  10 #include <asm/bitops.h>
  11
  12 #include <fsl_ddr.h>
  13
  14 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
  15 static unsigned int
  16 compute_cas_latency(const unsigned int ctrl_num,
  17                     const dimm_params_t *dimm_params,
  18                     common_timing_params_t *outpdimm,
  19                     unsigned int number_of_dimms)
  20 {
  21         unsigned int i;
  22         unsigned int common_caslat;
  23         unsigned int caslat_actual;
  24         unsigned int retry = 16;
  25         unsigned int tmp = ~0;
  26         const unsigned int mclk_ps = get_memory_clk_period_ps(ctrl_num);
  27 #ifdef CONFIG_SYS_FSL_DDR3
  28         const unsigned int taamax = 20000;
  29 #else
  30         const unsigned int taamax = 18000;
  31 #endif
  32
  33         /* compute the common CAS latency supported between slots */
  34         for (i = 0; i < number_of_dimms; i++) {
  35                 if (dimm_params[i].n_ranks)
  36                         tmp &= dimm_params[i].caslat_x;
  37         }
  38         common_caslat = tmp;
  39
  40         /* validate if the memory clk is in the range of dimms */
  41         if (mclk_ps < outpdimm->tckmin_x_ps) {
  42                 printf("DDR clock (MCLK cycle %u ps) is faster than "
  43                         "the slowest DIMM(s) (tCKmin %u ps) can support.\n",
  44                         mclk_ps, outpdimm->tckmin_x_ps);
  45         }
  46 #ifdef CONFIG_SYS_FSL_DDR4
  47         if (mclk_ps > outpdimm->tckmax_ps) {
  48                 printf("DDR clock (MCLK cycle %u ps) is slower than DIMM(s) (tCKmax %u ps) can support.\n",
  49                        mclk_ps, outpdimm->tckmax_ps);
  50         }
  51 #endif
  52         /* determine the acutal cas latency */
  53         caslat_actual = (outpdimm->taamin_ps + mclk_ps - 1) / mclk_ps;
  54         /* check if the dimms support the CAS latency */
  55         while (!(common_caslat & (1 << caslat_actual)) && retry > 0) {
  56                 caslat_actual++;
  57                 retry--;
  58         }
  59         /* once the caculation of caslat_actual is completed
  60          * we must verify that this CAS latency value does not
  61          * exceed tAAmax, which is 20 ns for all DDR3 speed grades,
  62          * 18ns for all DDR4 speed grades.
  63          */
  64         if (caslat_actual * mclk_ps > taamax) {
  65                 printf("The chosen cas latency %d is too large\n",
  66                        caslat_actual);
  67         }
  68         outpdimm->lowest_common_spd_caslat = caslat_actual;
  69         debug("lowest_common_spd_caslat is 0x%x\n", caslat_actual);
  70
  71         return 0;
  72 }
  73 #else   /* for DDR1 and DDR2 */
  74 static unsigned int
  75 compute_cas_latency(const unsigned int ctrl_num,
  76                     const dimm_params_t *dimm_params,
  77                     common_timing_params_t *outpdimm,
  78                     unsigned int number_of_dimms)
  79 {
  80         int i;
  81         const unsigned int mclk_ps = get_memory_clk_period_ps(ctrl_num);
  82         unsigned int lowest_good_caslat;
  83         unsigned int not_ok;
  84         unsigned int temp1, temp2;
  85
  86         debug("using mclk_ps = %u\n", mclk_ps);
  87         if (mclk_ps > outpdimm->tckmax_ps) {
  88                 printf("Warning: DDR clock (%u ps) is slower than DIMM(s) (tCKmax %u ps)\n",
  89                        mclk_ps, outpdimm->tckmax_ps);
  90         }
  91
  92         /*
  93          * Compute a CAS latency suitable for all DIMMs
  94          *
  95          * Strategy for SPD-defined latencies: compute only
  96          * CAS latency defined by all DIMMs.
  97          */
  98
  99         /*
 100          * Step 1: find CAS latency common to all DIMMs using bitwise
 101          * operation.
 102          */
 103         temp1 = 0xFF;
 104         for (i = 0; i < number_of_dimms; i++) {
 105                 if (dimm_params[i].n_ranks) {
 106                         temp2 = 0;
 107                         temp2 |= 1 << dimm_params[i].caslat_x;
 108                         temp2 |= 1 << dimm_params[i].caslat_x_minus_1;
 109                         temp2 |= 1 << dimm_params[i].caslat_x_minus_2;
 110                         /*
 111                          * If there was no entry for X-2 (X-1) in
 112                          * the SPD, then caslat_x_minus_2
 113                          * (caslat_x_minus_1) contains either 255 or
 114                          * 0xFFFFFFFF because that's what the glorious
 115                          * __ilog2 function returns for an input of 0.
 116                          * On 32-bit PowerPC, left shift counts with bit
 117                          * 26 set (that the value of 255 or 0xFFFFFFFF
 118                          * will have), cause the destination register to
 119                          * be 0.  That is why this works.
 120                          */
 121                         temp1 &= temp2;
 122                 }
 123         }
 124
 125         /*
 126          * Step 2: check each common CAS latency against tCK of each
 127          * DIMM's SPD.
 128          */
 129         lowest_good_caslat = 0;
 130         temp2 = 0;
 131         while (temp1) {
 132                 not_ok = 0;
 133                 temp2 =  __ilog2(temp1);
 134                 debug("checking common caslat = %u\n", temp2);
 135
 136                 /* Check if this CAS latency will work on all DIMMs at tCK. */
 137                 for (i = 0; i < number_of_dimms; i++) {
 138                         if (!dimm_params[i].n_ranks)
 139                                 continue;
 140
 141                         if (dimm_params[i].caslat_x == temp2) {
 142                                 if (mclk_ps >= dimm_params[i].tckmin_x_ps) {
 143                                         debug("CL = %u ok on DIMM %u at tCK=%u ps with tCKmin_X_ps of %u\n",
 144                                               temp2, i, mclk_ps,
 145                                               dimm_params[i].tckmin_x_ps);
 146                                         continue;
 147                                 } else {
 148                                         not_ok++;
 149                                 }
 150                         }
 151
 152                         if (dimm_params[i].caslat_x_minus_1 == temp2) {
 153                                 unsigned int tckmin_x_minus_1_ps
 154                                         = dimm_params[i].tckmin_x_minus_1_ps;
 155                                 if (mclk_ps >= tckmin_x_minus_1_ps) {
 156                                         debug("CL = %u ok on DIMM %u at tCK=%u ps with tckmin_x_minus_1_ps of %u\n",
 157                                               temp2, i, mclk_ps,
 158                                               tckmin_x_minus_1_ps);
 159                                         continue;
 160                                 } else {
 161                                         not_ok++;
 162                                 }
 163                         }
 164
 165                         if (dimm_params[i].caslat_x_minus_2 == temp2) {
 166                                 unsigned int tckmin_x_minus_2_ps
 167                                         = dimm_params[i].tckmin_x_minus_2_ps;
 168                                 if (mclk_ps >= tckmin_x_minus_2_ps) {
 169                                         debug("CL = %u ok on DIMM %u at tCK=%u ps with tckmin_x_minus_2_ps of %u\n",
 170                                               temp2, i, mclk_ps,
 171                                               tckmin_x_minus_2_ps);
 172                                         continue;
 173                                 } else {
 174                                         not_ok++;
 175                                 }
 176                         }
 177                 }
 178
 179                 if (!not_ok)
 180                         lowest_good_caslat = temp2;
 181
 182                 temp1 &= ~(1 << temp2);
 183         }
 184
 185         debug("lowest common SPD-defined CAS latency = %u\n",
 186               lowest_good_caslat);
 187         outpdimm->lowest_common_spd_caslat = lowest_good_caslat;
 188
 189
 190         /*
 191          * Compute a common 'de-rated' CAS latency.
 192          *
 193          * The strategy here is to find the *highest* dereated cas latency
 194          * with the assumption that all of the DIMMs will support a dereated
 195          * CAS latency higher than or equal to their lowest dereated value.
 196          */
 197         temp1 = 0;
 198         for (i = 0; i < number_of_dimms; i++)
 199                 temp1 = max(temp1, dimm_params[i].caslat_lowest_derated);
 200
 201         outpdimm->highest_common_derated_caslat = temp1;
 202         debug("highest common dereated CAS latency = %u\n", temp1);
 203
 204         return 0;
 205 }
 206 #endif
 207
 208 /*
 209  * compute_lowest_common_dimm_parameters()
 210  *
 211  * Determine the worst-case DIMM timing parameters from the set of DIMMs
 212  * whose parameters have been computed into the array pointed to
 213  * by dimm_params.
 214  */
 215 unsigned int
 216 compute_lowest_common_dimm_parameters(const unsigned int ctrl_num,
 217                                       const dimm_params_t *dimm_params,
 218                                       common_timing_params_t *outpdimm,
 219                                       const unsigned int number_of_dimms)
 220 {
 221         unsigned int i, j;
 222
 223         unsigned int tckmin_x_ps = 0;
 224         unsigned int tckmax_ps = 0xFFFFFFFF;
 225         unsigned int trcd_ps = 0;
 226         unsigned int trp_ps = 0;
 227         unsigned int tras_ps = 0;
 228 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
 229         unsigned int taamin_ps = 0;
 230 #endif
 231 #ifdef CONFIG_SYS_FSL_DDR4
 232         unsigned int twr_ps = 15000;
 233         unsigned int trfc1_ps = 0;
 234         unsigned int trfc2_ps = 0;
 235         unsigned int trfc4_ps = 0;
 236         unsigned int trrds_ps = 0;
 237         unsigned int trrdl_ps = 0;
 238         unsigned int tccdl_ps = 0;
 239         unsigned int trfc_slr_ps = 0;
 240 #else
 241         unsigned int twr_ps = 0;
 242         unsigned int twtr_ps = 0;
 243         unsigned int trfc_ps = 0;
 244         unsigned int trrd_ps = 0;
 245         unsigned int trtp_ps = 0;
 246 #endif
 247         unsigned int trc_ps = 0;
 248         unsigned int refresh_rate_ps = 0;
 249         unsigned int extended_op_srt = 1;
 250 #if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2)
 251         unsigned int tis_ps = 0;
 252         unsigned int tih_ps = 0;
 253         unsigned int tds_ps = 0;
 254         unsigned int tdh_ps = 0;
 255         unsigned int tdqsq_max_ps = 0;
 256         unsigned int tqhs_ps = 0;
 257 #endif
 258         unsigned int temp1, temp2;
 259         unsigned int additive_latency = 0;
 260
 261         temp1 = 0;
 262         for (i = 0; i < number_of_dimms; i++) {
 263                 /*
 264                  * If there are no ranks on this DIMM,
 265                  * it probably doesn't exist, so skip it.
 266                  */
 267                 if (dimm_params[i].n_ranks == 0) {
 268                         temp1++;
 269                         continue;
 270                 }
 271                 if (dimm_params[i].n_ranks == 4 && i != 0) {
 272                         printf("Found Quad-rank DIMM in wrong bank, ignored."
 273                                 " Software may not run as expected.\n");
 274                         temp1++;
 275                         continue;
 276                 }
 277
 278                 /*
 279                  * check if quad-rank DIMM is plugged if
 280                  * CONFIG_CHIP_SELECT_QUAD_CAPABLE is not defined
 281                  * Only the board with proper design is capable
 282                  */
 283 #ifndef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
 284                 if (dimm_params[i].n_ranks == 4 && \
 285                   CONFIG_CHIP_SELECTS_PER_CTRL/CONFIG_DIMM_SLOTS_PER_CTLR < 4) {
 286                         printf("Found Quad-rank DIMM, not able to support.");
 287                         temp1++;
 288                         continue;
 289                 }
 290 #endif
 291                 /*
 292                  * Find minimum tckmax_ps to find fastest slow speed,
 293                  * i.e., this is the slowest the whole system can go.
 294                  */
 295                 tckmax_ps = min(tckmax_ps,
 296                                 (unsigned int)dimm_params[i].tckmax_ps);
 297 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
 298                 taamin_ps = max(taamin_ps,
 299                                 (unsigned int)dimm_params[i].taa_ps);
 300 #endif
 301                 tckmin_x_ps = max(tckmin_x_ps,
 302                                   (unsigned int)dimm_params[i].tckmin_x_ps);
 303                 trcd_ps = max(trcd_ps, (unsigned int)dimm_params[i].trcd_ps);
 304                 trp_ps = max(trp_ps, (unsigned int)dimm_params[i].trp_ps);
 305                 tras_ps = max(tras_ps, (unsigned int)dimm_params[i].tras_ps);
 306 #ifdef CONFIG_SYS_FSL_DDR4
 307                 trfc1_ps = max(trfc1_ps,
 308                                (unsigned int)dimm_params[i].trfc1_ps);
 309                 trfc2_ps = max(trfc2_ps,
 310                                (unsigned int)dimm_params[i].trfc2_ps);
 311                 trfc4_ps = max(trfc4_ps,
 312                                (unsigned int)dimm_params[i].trfc4_ps);
 313                 trrds_ps = max(trrds_ps,
 314                                (unsigned int)dimm_params[i].trrds_ps);
 315                 trrdl_ps = max(trrdl_ps,
 316                                (unsigned int)dimm_params[i].trrdl_ps);
 317                 tccdl_ps = max(tccdl_ps,
 318                                (unsigned int)dimm_params[i].tccdl_ps);
 319                 trfc_slr_ps = max(trfc_slr_ps,
 320                                   (unsigned int)dimm_params[i].trfc_slr_ps);
 321 #else
 322                 twr_ps = max(twr_ps, (unsigned int)dimm_params[i].twr_ps);
 323                 twtr_ps = max(twtr_ps, (unsigned int)dimm_params[i].twtr_ps);
 324                 trfc_ps = max(trfc_ps, (unsigned int)dimm_params[i].trfc_ps);
 325                 trrd_ps = max(trrd_ps, (unsigned int)dimm_params[i].trrd_ps);
 326                 trtp_ps = max(trtp_ps, (unsigned int)dimm_params[i].trtp_ps);
 327 #endif
 328                 trc_ps = max(trc_ps, (unsigned int)dimm_params[i].trc_ps);
 329 #if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2)
 330                 tis_ps = max(tis_ps, (unsigned int)dimm_params[i].tis_ps);
 331                 tih_ps = max(tih_ps, (unsigned int)dimm_params[i].tih_ps);
 332                 tds_ps = max(tds_ps, (unsigned int)dimm_params[i].tds_ps);
 333                 tdh_ps = max(tdh_ps, (unsigned int)dimm_params[i].tdh_ps);
 334                 tqhs_ps = max(tqhs_ps, (unsigned int)dimm_params[i].tqhs_ps);
 335                 /*
 336                  * Find maximum tdqsq_max_ps to find slowest.
 337                  *
 338                  * FIXME: is finding the slowest value the correct
 339                  * strategy for this parameter?
 340                  */
 341                 tdqsq_max_ps = max(tdqsq_max_ps,
 342                                    (unsigned int)dimm_params[i].tdqsq_max_ps);
 343 #endif
 344                 refresh_rate_ps = max(refresh_rate_ps,
 345                                       (unsigned int)dimm_params[i].refresh_rate_ps);
 346                 /* extended_op_srt is either 0 or 1, 0 having priority */
 347                 extended_op_srt = min(extended_op_srt,
 348                                       (unsigned int)dimm_params[i].extended_op_srt);
 349         }
 350
 351         outpdimm->ndimms_present = number_of_dimms - temp1;
 352
 353         if (temp1 == number_of_dimms) {
 354                 debug("no dimms this memory controller\n");
 355                 return 0;
 356         }
 357
 358         outpdimm->tckmin_x_ps = tckmin_x_ps;
 359         outpdimm->tckmax_ps = tckmax_ps;
 360 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
 361         outpdimm->taamin_ps = taamin_ps;
 362 #endif
 363         outpdimm->trcd_ps = trcd_ps;
 364         outpdimm->trp_ps = trp_ps;
 365         outpdimm->tras_ps = tras_ps;
 366 #ifdef CONFIG_SYS_FSL_DDR4
 367         outpdimm->trfc1_ps = trfc1_ps;
 368         outpdimm->trfc2_ps = trfc2_ps;
 369         outpdimm->trfc4_ps = trfc4_ps;
 370         outpdimm->trrds_ps = trrds_ps;
 371         outpdimm->trrdl_ps = trrdl_ps;
 372         outpdimm->tccdl_ps = tccdl_ps;
 373         outpdimm->trfc_slr_ps = trfc_slr_ps;
 374 #else
 375         outpdimm->twtr_ps = twtr_ps;
 376         outpdimm->trfc_ps = trfc_ps;
 377         outpdimm->trrd_ps = trrd_ps;
 378         outpdimm->trtp_ps = trtp_ps;
 379 #endif
 380         outpdimm->twr_ps = twr_ps;
 381         outpdimm->trc_ps = trc_ps;
 382         outpdimm->refresh_rate_ps = refresh_rate_ps;
 383         outpdimm->extended_op_srt = extended_op_srt;
 384 #if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2)
 385         outpdimm->tis_ps = tis_ps;
 386         outpdimm->tih_ps = tih_ps;
 387         outpdimm->tds_ps = tds_ps;
 388         outpdimm->tdh_ps = tdh_ps;
 389         outpdimm->tdqsq_max_ps = tdqsq_max_ps;
 390         outpdimm->tqhs_ps = tqhs_ps;
 391 #endif
 392
 393         /* Determine common burst length for all DIMMs. */
 394         temp1 = 0xff;
 395         for (i = 0; i < number_of_dimms; i++) {
 396                 if (dimm_params[i].n_ranks) {
 397                         temp1 &= dimm_params[i].burst_lengths_bitmask;
 398                 }
 399         }
 400         outpdimm->all_dimms_burst_lengths_bitmask = temp1;
 401
 402         /* Determine if all DIMMs registered buffered. */
 403         temp1 = temp2 = 0;
 404         for (i = 0; i < number_of_dimms; i++) {
 405                 if (dimm_params[i].n_ranks) {
 406                         if (dimm_params[i].registered_dimm) {
 407                                 temp1 = 1;
 408 #ifndef CONFIG_SPL_BUILD
 409                                 printf("Detected RDIMM %s\n",
 410                                         dimm_params[i].mpart);
 411 #endif
 412                         } else {
 413                                 temp2 = 1;
 414 #ifndef CONFIG_SPL_BUILD
 415                                 printf("Detected UDIMM %s\n",
 416                                         dimm_params[i].mpart);
 417 #endif
 418                         }
 419                 }
 420         }
 421
 422         outpdimm->all_dimms_registered = 0;
 423         outpdimm->all_dimms_unbuffered = 0;
 424         if (temp1 && !temp2) {
 425                 outpdimm->all_dimms_registered = 1;
 426         } else if (!temp1 && temp2) {
 427                 outpdimm->all_dimms_unbuffered = 1;
 428         } else {
 429                 printf("ERROR:  Mix of registered buffered and unbuffered "
 430                                 "DIMMs detected!\n");
 431         }
 432
 433         temp1 = 0;
 434         if (outpdimm->all_dimms_registered)
 435                 for (j = 0; j < 16; j++) {
 436                         outpdimm->rcw[j] = dimm_params[0].rcw[j];
 437                         for (i = 1; i < number_of_dimms; i++) {
 438                                 if (!dimm_params[i].n_ranks)
 439                                         continue;
 440                                 if (dimm_params[i].rcw[j] != dimm_params[0].rcw[j]) {
 441                                         temp1 = 1;
 442                                         break;
 443                                 }
 444                         }
 445                 }
 446
 447         if (temp1 != 0)
 448                 printf("ERROR: Mix different RDIMM detected!\n");
 449
 450         /* calculate cas latency for all DDR types */
 451         if (compute_cas_latency(ctrl_num, dimm_params,
 452                                 outpdimm, number_of_dimms))
 453                 return 1;
 454
 455         /* Determine if all DIMMs ECC capable. */
 456         temp1 = 1;
 457         for (i = 0; i < number_of_dimms; i++) {
 458                 if (dimm_params[i].n_ranks &&
 459                         !(dimm_params[i].edc_config & EDC_ECC)) {
 460                         temp1 = 0;
 461                         break;
 462                 }
 463         }
 464         if (temp1) {
 465                 debug("all DIMMs ECC capable\n");
 466         } else {
 467                 debug("Warning: not all DIMMs ECC capable, cant enable ECC\n");
 468         }
 469         outpdimm->all_dimms_ecc_capable = temp1;
 470
 471         /*
 472          * Compute additive latency.
 473          *
 474          * For DDR1, additive latency should be 0.
 475          *
 476          * For DDR2, with ODT enabled, use "a value" less than ACTTORW,
 477          *      which comes from Trcd, and also note that:
 478          *          add_lat + caslat must be >= 4
 479          *
 480          * For DDR3, we use the AL=0
 481          *
 482          * When to use additive latency for DDR2:
 483          *
 484          * I. Because you are using CL=3 and need to do ODT on writes and
 485          *    want functionality.
 486          *    1. Are you going to use ODT? (Does your board not have
 487          *      additional termination circuitry for DQ, DQS, DQS_,
 488          *      DM, RDQS, RDQS_ for x4/x8 configs?)
 489          *    2. If so, is your lowest supported CL going to be 3?
 490          *    3. If so, then you must set AL=1 because
 491          *
 492          *       WL >= 3 for ODT on writes
 493          *       RL = AL + CL
 494          *       WL = RL - 1
 495          *       ->
 496          *       WL = AL + CL - 1
 497          *       AL + CL - 1 >= 3
 498          *       AL + CL >= 4
 499          *  QED
 500          *
 501          *  RL >= 3 for ODT on reads
 502          *  RL = AL + CL
 503          *
 504          *  Since CL aren't usually less than 2, AL=0 is a minimum,
 505          *  so the WL-derived AL should be the  -- FIXME?
 506          *
 507          * II. Because you are using auto-precharge globally and want to
 508          *     use additive latency (posted CAS) to get more bandwidth.
 509          *     1. Are you going to use auto-precharge mode globally?
 510          *
 511          *        Use addtivie latency and compute AL to be 1 cycle less than
 512          *        tRCD, i.e. the READ or WRITE command is in the cycle
 513          *        immediately following the ACTIVATE command..
 514          *
 515          * III. Because you feel like it or want to do some sort of
 516          *      degraded-performance experiment.
 517          *     1.  Do you just want to use additive latency because you feel
 518          *         like it?
 519          *
 520          * Validation:  AL is less than tRCD, and within the other
 521          * read-to-precharge constraints.
 522          */
 523
 524         additive_latency = 0;
 525
 526 #if defined(CONFIG_SYS_FSL_DDR2)
 527         if ((outpdimm->lowest_common_spd_caslat < 4) &&
 528             (picos_to_mclk(ctrl_num, trcd_ps) >
 529              outpdimm->lowest_common_spd_caslat)) {
 530                 additive_latency = picos_to_mclk(ctrl_num, trcd_ps) -
 531                                    outpdimm->lowest_common_spd_caslat;
 532                 if (mclk_to_picos(ctrl_num, additive_latency) > trcd_ps) {
 533                         additive_latency = picos_to_mclk(ctrl_num, trcd_ps);
 534                         debug("setting additive_latency to %u because it was "
 535                                 " greater than tRCD_ps\n", additive_latency);
 536                 }
 537         }
 538 #endif
 539
 540         /*
 541          * Validate additive latency
 542          *
 543          * AL <= tRCD(min)
 544          */
 545         if (mclk_to_picos(ctrl_num, additive_latency) > trcd_ps) {
 546                 printf("Error: invalid additive latency exceeds tRCD(min).\n");
 547                 return 1;
 548         }
 549
 550         /*
 551          * RL = CL + AL;  RL >= 3 for ODT_RD_CFG to be enabled
 552          * WL = RL - 1;  WL >= 3 for ODT_WL_CFG to be enabled
 553          * ADD_LAT (the register) must be set to a value less
 554          * than ACTTORW if WL = 1, then AL must be set to 1
 555          * RD_TO_PRE (the register) must be set to a minimum
 556          * tRTP + AL if AL is nonzero
 557          */
 558
 559         /*
 560          * Additive latency will be applied only if the memctl option to
 561          * use it.
 562          */
 563         outpdimm->additive_latency = additive_latency;
 564
 565         debug("tCKmin_ps = %u\n", outpdimm->tckmin_x_ps);
 566         debug("trcd_ps   = %u\n", outpdimm->trcd_ps);
 567         debug("trp_ps    = %u\n", outpdimm->trp_ps);
 568         debug("tras_ps   = %u\n", outpdimm->tras_ps);
 569 #ifdef CONFIG_SYS_FSL_DDR4
 570         debug("trfc1_ps = %u\n", trfc1_ps);
 571         debug("trfc2_ps = %u\n", trfc2_ps);
 572         debug("trfc4_ps = %u\n", trfc4_ps);
 573         debug("trrds_ps = %u\n", trrds_ps);
 574         debug("trrdl_ps = %u\n", trrdl_ps);
 575         debug("tccdl_ps = %u\n", tccdl_ps);
 576         debug("trfc_slr_ps = %u\n", trfc_slr_ps);
 577 #else
 578         debug("twtr_ps   = %u\n", outpdimm->twtr_ps);
 579         debug("trfc_ps   = %u\n", outpdimm->trfc_ps);
 580         debug("trrd_ps   = %u\n", outpdimm->trrd_ps);
 581 #endif
 582         debug("twr_ps    = %u\n", outpdimm->twr_ps);
 583         debug("trc_ps    = %u\n", outpdimm->trc_ps);
 584
 585         return 0;
 586 }