3 * Texas Instruments Incorporated, <www.ti.com>
4 * Steve Sakoman <steve@sakoman.com>
6 * SPDX-License-Identifier: GPL-2.0+
9 #include <asm/arch/sys_proto.h>
10 #include <asm/arch/mmc_host_def.h>
11 #include <asm/arch/clock.h>
12 #include <asm/arch/gpio.h>
16 #include "panda_mux_data.h"
18 #ifdef CONFIG_USB_EHCI
20 #include <asm/arch/ehci.h>
21 #include <asm/ehci-omap.h>
24 #define PANDA_ULPI_PHY_TYPE_GPIO 182
25 #define PANDA_BOARD_ID_1_GPIO 101
26 #define PANDA_ES_BOARD_ID_1_GPIO 48
27 #define PANDA_BOARD_ID_2_GPIO 171
28 #define PANDA_ES_BOARD_ID_3_GPIO 3
29 #define PANDA_ES_BOARD_ID_4_GPIO 2
31 DECLARE_GLOBAL_DATA_PTR;
33 const struct omap_sysinfo sysinfo = {
34 "Board: OMAP4 Panda\n"
37 struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000;
48 gd->bd->bi_arch_number = MACH_TYPE_OMAP4_PANDA;
49 gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */
54 int board_eth_init(bd_t *bis)
60 * Routine: get_board_revision
61 * Description: Detect if we are running on a panda revision A1-A6,
62 * or an ES panda board. This can be done by reading
63 * the level of GPIOs and checking the processor revisions.
64 * This should result in:
66 * GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
67 * GPIO171, GPIO101, GPIO182: 1 0 1 => A6
69 * GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
70 * GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
72 int get_board_revision(void)
74 int board_id0, board_id1, board_id2;
75 int board_id3, board_id4;
78 int processor_rev = omap_revision();
80 /* Setup the mux for the common board ID pins (gpio 171 and 182) */
81 writew((IEN | M3), (*ctrl)->control_padconf_core_base + UNIPRO_TX0);
82 writew((IEN | M3), (*ctrl)->control_padconf_core_base + FREF_CLK2_OUT);
84 board_id0 = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
85 board_id2 = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
87 if ((processor_rev >= OMAP4460_ES1_0 &&
88 processor_rev <= OMAP4460_ES1_1)) {
90 * Setup the mux for the ES specific board ID pins (gpio 101,
93 writew((IEN | M3), (*ctrl)->control_padconf_core_base +
95 writew((IEN | M3), (*ctrl)->control_padconf_core_base +
97 writew((IEN | M3), (*ctrl)->control_padconf_core_base +
100 board_id1 = gpio_get_value(PANDA_ES_BOARD_ID_1_GPIO);
101 board_id3 = gpio_get_value(PANDA_ES_BOARD_ID_3_GPIO);
102 board_id4 = gpio_get_value(PANDA_ES_BOARD_ID_4_GPIO);
104 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
105 setenv("board_name", "panda-es");
107 board_id = ((board_id4 << 4) | (board_id3 << 3) |
108 (board_id2 << 2) | (board_id1 << 1) | (board_id0));
110 /* Setup the mux for the Ax specific board ID pins (gpio 101) */
111 writew((IEN | M3), (*ctrl)->control_padconf_core_base +
114 board_id1 = gpio_get_value(PANDA_BOARD_ID_1_GPIO);
115 board_id = ((board_id2 << 2) | (board_id1 << 1) | (board_id0));
117 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
118 if ((board_id >= 0x3) && (processor_rev == OMAP4430_ES2_3))
119 setenv("board_name", "panda-a4");
127 * is_panda_es_rev_b3() - Detect if we are running on rev B3 of panda board ES
130 * Detect if we are running on B3 version of ES panda board,
131 * This can be done by reading the level of GPIO 171 and checking the
132 * processor revisions.
133 * GPIO171: 1 => Panda ES Rev B3
135 * Return : return 1 if Panda ES Rev B3 , else return 0
137 u8 is_panda_es_rev_b3(void)
139 int processor_rev = omap_revision();
142 if ((processor_rev >= OMAP4460_ES1_0 &&
143 processor_rev <= OMAP4460_ES1_1)) {
145 /* Setup the mux for the common board ID pins (gpio 171) */
147 (*ctrl)->control_padconf_core_base + UNIPRO_TX0);
149 /* if processor_rev is panda ES and GPIO171 is 1,it is rev b3 */
150 ret = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
155 #ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
157 * emif_get_reg_dump() - emif_get_reg_dump strong function
159 * @emif_nr - emif base
160 * @regs - reg dump of timing values
162 * Strong function to override emif_get_reg_dump weak function in sdram_elpida.c
164 void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
166 u32 omap4_rev = omap_revision();
168 /* Same devices and geometry on both EMIFs */
169 if (omap4_rev == OMAP4430_ES1_0)
170 *regs = &emif_regs_elpida_380_mhz_1cs;
171 else if (omap4_rev == OMAP4430_ES2_0)
172 *regs = &emif_regs_elpida_200_mhz_2cs;
173 else if (omap4_rev == OMAP4430_ES2_3)
174 *regs = &emif_regs_elpida_400_mhz_1cs;
175 else if (omap4_rev < OMAP4470_ES1_0) {
176 if(is_panda_es_rev_b3())
177 *regs = &emif_regs_elpida_400_mhz_1cs;
179 *regs = &emif_regs_elpida_400_mhz_2cs;
182 *regs = &emif_regs_elpida_400_mhz_1cs;
185 void emif_get_dmm_regs(const struct dmm_lisa_map_regs
188 u32 omap_rev = omap_revision();
190 if (omap_rev == OMAP4430_ES1_0)
191 *dmm_lisa_regs = &lisa_map_2G_x_1_x_2;
192 else if (omap_rev == OMAP4430_ES2_3)
193 *dmm_lisa_regs = &lisa_map_2G_x_2_x_2;
194 else if (omap_rev < OMAP4460_ES1_0)
195 *dmm_lisa_regs = &lisa_map_2G_x_2_x_2;
197 *dmm_lisa_regs = &ma_lisa_map_2G_x_2_x_2;
203 * @brief misc_init_r - Configure Panda board specific configurations
204 * such as power configurations, ethernet initialization as phase2 of
209 int misc_init_r(void)
212 u32 auxclk, altclksrc;
214 /* EHCI is not supported on ES1.0 */
215 if (omap_revision() == OMAP4430_ES1_0)
218 get_board_revision();
220 gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO);
221 phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
224 /* ULPI PHY supplied by auxclk3 derived from sys_clk */
225 debug("ULPI PHY supplied by auxclk3\n");
227 auxclk = readl(&scrm->auxclk3);
229 auxclk &= ~AUXCLK_SRCSELECT_MASK;
230 auxclk |= AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT;
231 /* Set the divisor to 2 */
232 auxclk &= ~AUXCLK_CLKDIV_MASK;
233 auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT;
234 /* Request auxilary clock #3 */
235 auxclk |= AUXCLK_ENABLE_MASK;
237 writel(auxclk, &scrm->auxclk3);
239 /* ULPI PHY supplied by auxclk1 derived from PER dpll */
240 debug("ULPI PHY supplied by auxclk1\n");
242 auxclk = readl(&scrm->auxclk1);
243 /* Select per DPLL */
244 auxclk &= ~AUXCLK_SRCSELECT_MASK;
245 auxclk |= AUXCLK_SRCSELECT_PER_DPLL << AUXCLK_SRCSELECT_SHIFT;
246 /* Set the divisor to 16 */
247 auxclk &= ~AUXCLK_CLKDIV_MASK;
248 auxclk |= AUXCLK_CLKDIV_16 << AUXCLK_CLKDIV_SHIFT;
249 /* Request auxilary clock #3 */
250 auxclk |= AUXCLK_ENABLE_MASK;
252 writel(auxclk, &scrm->auxclk1);
255 altclksrc = readl(&scrm->altclksrc);
257 /* Activate alternate system clock supplier */
258 altclksrc &= ~ALTCLKSRC_MODE_MASK;
259 altclksrc |= ALTCLKSRC_MODE_ACTIVE;
262 altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK;
264 writel(altclksrc, &scrm->altclksrc);
266 omap_die_id_usbethaddr();
271 void set_muxconf_regs_essential(void)
273 do_set_mux((*ctrl)->control_padconf_core_base,
274 core_padconf_array_essential,
275 sizeof(core_padconf_array_essential) /
276 sizeof(struct pad_conf_entry));
278 do_set_mux((*ctrl)->control_padconf_wkup_base,
279 wkup_padconf_array_essential,
280 sizeof(wkup_padconf_array_essential) /
281 sizeof(struct pad_conf_entry));
283 if (omap_revision() >= OMAP4460_ES1_0)
284 do_set_mux((*ctrl)->control_padconf_wkup_base,
285 wkup_padconf_array_essential_4460,
286 sizeof(wkup_padconf_array_essential_4460) /
287 sizeof(struct pad_conf_entry));
290 #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
291 int board_mmc_init(bd_t *bis)
293 return omap_mmc_init(0, 0, 0, -1, -1);
296 void board_mmc_power_init(void)
298 twl6030_power_mmc_init(0);
302 #ifdef CONFIG_USB_EHCI
304 static struct omap_usbhs_board_data usbhs_bdata = {
305 .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
306 .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
307 .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
310 int ehci_hcd_init(int index, enum usb_init_type init,
311 struct ehci_hccr **hccr, struct ehci_hcor **hcor)
314 unsigned int utmi_clk;
316 /* Now we can enable our port clocks */
317 utmi_clk = readl((void *)CM_L3INIT_HSUSBHOST_CLKCTRL);
318 utmi_clk |= HSUSBHOST_CLKCTRL_CLKSEL_UTMI_P1_MASK;
319 setbits_le32((void *)CM_L3INIT_HSUSBHOST_CLKCTRL, utmi_clk);
321 ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
328 int ehci_hcd_stop(int index)
330 return omap_ehci_hcd_stop();
335 * get_board_rev() - get board revision
337 u32 get_board_rev(void)