1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright (C) 2015 Stefan Roese <sr@denx.de>
11 #include <asm/arch/cpu.h>
12 #include <asm/arch/soc.h>
13 #include "../common/tlv_data.h"
15 #include "../drivers/ddr/marvell/a38x/ddr3_init.h"
16 #include <../serdes/a38x/high_speed_env_spec.h>
18 DECLARE_GLOBAL_DATA_PTR;
21 * Those values and defines are taken from the Marvell U-Boot version
22 * "u-boot-2013.01-15t1-clearfog"
24 #define BOARD_GPP_OUT_ENA_LOW 0xffffffff
25 #define BOARD_GPP_OUT_ENA_MID 0xffffffff
27 #define BOARD_GPP_OUT_VAL_LOW 0x0
28 #define BOARD_GPP_OUT_VAL_MID 0x0
29 #define BOARD_GPP_POL_LOW 0x0
30 #define BOARD_GPP_POL_MID 0x0
32 static struct tlv_data cf_tlv_data;
34 static void cf_read_tlv_data(void)
36 static bool read_once;
42 read_tlv_data(&cf_tlv_data);
45 /* The starting board_serdes_map reflects original Clearfog Pro usage */
46 static struct serdes_map board_serdes_map[] = {
47 {SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
48 {SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
49 {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
50 {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
51 {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
52 {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
55 void config_cfbase_serdes_map(void)
57 board_serdes_map[4].serdes_type = USB3_HOST0;
58 board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
59 board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
62 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
66 /* Apply build configuration options before runtime configuration */
67 if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
68 board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;
70 if (IS_ENABLED(CONFIG_CLEARFOG_CON2_SATA)) {
71 board_serdes_map[4].serdes_type = SATA2;
72 board_serdes_map[4].serdes_speed = SERDES_SPEED_3_GBPS;
73 board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
74 board_serdes_map[4].swap_rx = 1;
77 if (IS_ENABLED(CONFIG_CLEARFOG_CON3_SATA)) {
78 board_serdes_map[2].serdes_type = SATA1;
79 board_serdes_map[2].serdes_speed = SERDES_SPEED_3_GBPS;
80 board_serdes_map[2].serdes_mode = SERDES_DEFAULT_MODE;
81 board_serdes_map[2].swap_rx = 1;
84 /* Apply runtime detection changes */
85 if (sr_product_is(&cf_tlv_data, "Clearfog GTR")) {
86 board_serdes_map[0].serdes_type = PEX0;
87 board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS;
88 board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1;
89 } else if (sr_product_is(&cf_tlv_data, "Clearfog Pro")) {
90 /* handle recognized product as noop, no adjustment required */
91 } else if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
92 config_cfbase_serdes_map();
95 * Fallback to static default. EEPROM TLV support is not
96 * enabled, runtime detection failed, hardware support is not
97 * present, EEPROM is corrupt, or an unrecognized product name
100 if (IS_ENABLED(CONFIG_SPL_CMD_TLV_EEPROM))
101 puts("EEPROM TLV detection failed: ");
102 puts("Using static config for ");
103 if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
104 puts("Clearfog Base.\n");
105 config_cfbase_serdes_map();
107 puts("Clearfog Pro.\n");
111 *serdes_map_array = board_serdes_map;
112 *count = ARRAY_SIZE(board_serdes_map);
117 * Define the DDR layout / topology here in the board file. This will
118 * be used by the DDR3 init code in the SPL U-Boot version to configure
119 * the DDR3 controller.
121 static struct mv_ddr_topology_map board_topology_map = {
123 0x1, /* active interfaces */
124 /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
125 { { { {0x1, 0, 0, 0},
130 SPEED_BIN_DDR_1600K, /* speed_bin */
131 MV_DDR_DEV_WIDTH_16BIT, /* memory_width */
132 MV_DDR_DIE_CAP_4GBIT, /* mem_size */
133 MV_DDR_FREQ_800, /* frequency */
134 0, 0, /* cas_wl cas_l */
135 MV_DDR_TEMP_LOW, /* temperature */
136 MV_DDR_TIM_DEFAULT} }, /* timing */
137 BUS_MASK_32BIT, /* Busses mask */
138 MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
139 { {0} }, /* raw spd data */
140 {0}, /* timing parameters */
141 { {0} }, /* electrical configuration */
142 {0,}, /* electrical parameters */
143 0x3, /* clock enable mask */
146 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
148 struct if_params *ifp = &board_topology_map.interface_params[0];
152 switch (cf_tlv_data.ram_size) {
155 ifp->memory_size = MV_DDR_DIE_CAP_4GBIT;
158 ifp->memory_size = MV_DDR_DIE_CAP_8GBIT;
162 /* Return the board topology as defined in the board code */
163 return &board_topology_map;
166 int board_early_init_f(void)
169 writel(0x11111111, MVEBU_MPP_BASE + 0x00);
170 writel(0x11111111, MVEBU_MPP_BASE + 0x04);
171 writel(0x10400011, MVEBU_MPP_BASE + 0x08);
172 writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
173 writel(0x44400002, MVEBU_MPP_BASE + 0x10);
174 writel(0x41144004, MVEBU_MPP_BASE + 0x14);
175 writel(0x40333333, MVEBU_MPP_BASE + 0x18);
176 writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
178 /* Set GPP Out value */
179 writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
180 writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
182 /* Set GPP Polarity */
183 writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
184 writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
186 /* Set GPP Out Enable */
187 writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
188 writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
195 /* Address of boot parameters */
196 gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
198 /* Toggle GPIO41 to reset onboard switch and phy */
199 clrbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
200 clrbits_le32(MVEBU_GPIO1_BASE + 0x4, BIT(9));
201 /* GPIO 19 on ClearFog rev 2.1 controls the uSOM onboard phy reset */
202 clrbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
203 clrbits_le32(MVEBU_GPIO0_BASE + 0x4, BIT(19));
205 setbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
206 setbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
214 char *board = "Clearfog Pro";
215 if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
216 board = "Clearfog Base";
219 if (strlen(cf_tlv_data.tlv_product_name[0]) > 0)
220 board = cf_tlv_data.tlv_product_name[0];
222 printf("Board: SolidRun %s", board);
223 if (strlen(cf_tlv_data.tlv_product_name[1]) > 0)
224 printf(", %s", cf_tlv_data.tlv_product_name[1]);
230 int board_eth_init(bd_t *bis)
232 cpu_eth_init(bis); /* Built in controller(s) come first */
233 return pci_eth_init(bis);
236 int board_late_init(void)
240 if (sr_product_is(&cf_tlv_data, "Clearfog Base"))
241 env_set("fdtfile", "armada-388-clearfog-base.dtb");
242 else if (sr_product_is(&cf_tlv_data, "Clearfog GTR S4"))
243 env_set("fdtfile", "armada-385-clearfog-gtr-s4.dtb");
244 else if (sr_product_is(&cf_tlv_data, "Clearfog GTR L8"))
245 env_set("fdtfile", "armada-385-clearfog-gtr-l8.dtb");
246 else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
247 env_set("fdtfile", "armada-388-clearfog-base.dtb");