1 // SPDX-License-Identifier: GPL-2.0+
3 * Board file for the VInCo platform
4 * Based on the the SAMA5-EK board file
5 * Configuration settings for the VInCo platform.
6 * Copyright (C) 2014 Atmel
7 * Bo Shen <voice.shen@atmel.com>
8 * Copyright (C) 2015 Free Electrons
9 * Gregory CLEMENT <gregory.clement@free-electrons.com>
15 #include <asm/arch/at91_common.h>
16 #include <asm/arch/at91_pmc.h>
17 #include <asm/arch/at91_rstc.h>
18 #include <asm/arch/atmel_mpddrc.h>
19 #include <asm/arch/atmel_usba_udc.h>
20 #include <asm/arch/gpio.h>
21 #include <asm/arch/clk.h>
22 #include <asm/arch/sama5d3_smc.h>
23 #include <asm/arch/sama5d4.h>
24 #include <atmel_hlcdc.h>
25 #include <atmel_mci.h>
34 DECLARE_GLOBAL_DATA_PTR;
36 /* FIXME gpio code here need to handle through DM_GPIO */
38 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
40 return bus == 0 && cs == 0;
43 void spi_cs_activate(struct spi_slave *slave)
45 at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
48 void spi_cs_deactivate(struct spi_slave *slave)
50 at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
53 static void vinco_spi0_hw_init(void)
55 at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */
56 at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */
57 at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */
59 at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */
62 at91_periph_clk_enable(ATMEL_ID_SPI0);
64 #endif /* CONFIG_ATMEL_SPI */
68 static void vinco_usb_hw_init(void)
70 at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
71 at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
72 at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
77 #ifdef CONFIG_GENERIC_ATMEL_MCI
78 void vinco_mci0_hw_init(void)
80 at91_pio3_set_b_periph(AT91_PIO_PORTC, 5, 1); /* MCI0 CDA */
81 at91_pio3_set_b_periph(AT91_PIO_PORTC, 6, 1); /* MCI0 DA0 */
82 at91_pio3_set_b_periph(AT91_PIO_PORTC, 7, 1); /* MCI0 DA1 */
83 at91_pio3_set_b_periph(AT91_PIO_PORTC, 8, 1); /* MCI0 DA2 */
84 at91_pio3_set_b_periph(AT91_PIO_PORTC, 9, 1); /* MCI0 DA3 */
85 at91_pio3_set_b_periph(AT91_PIO_PORTC, 10, 1); /* MCI0 DA4 */
86 at91_pio3_set_b_periph(AT91_PIO_PORTC, 11, 1); /* MCI0 DA5 */
87 at91_pio3_set_b_periph(AT91_PIO_PORTC, 12, 1); /* MCI0 DA6 */
88 at91_pio3_set_b_periph(AT91_PIO_PORTC, 13, 1); /* MCI0 DA7 */
89 at91_pio3_set_b_periph(AT91_PIO_PORTC, 4, 0); /* MCI0 CLK */
92 * As the mci io internal pull down is too strong, so if the io needs
93 * external pull up, the pull up resistor will be very small, if so
94 * the power consumption will increase, so disable the interanl pull
95 * down to save the power.
97 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 4, 0);
98 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 5, 0);
99 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 6, 0);
100 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 7, 0);
101 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 8, 0);
102 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 9, 0);
103 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 10, 0);
104 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 11, 0);
105 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 12, 0);
106 at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 13, 0);
109 at91_periph_clk_enable(ATMEL_ID_MCI0);
112 int board_mmc_init(bd_t *bis)
114 /* Enable power for MCI0 interface */
115 at91_set_pio_output(AT91_PIO_PORTE, 7, 1);
117 return atmel_mci_init((void *)ATMEL_BASE_MCI0);
119 #endif /* CONFIG_GENERIC_ATMEL_MCI */
122 void vinco_macb0_hw_init(void)
124 at91_pio3_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */
125 at91_pio3_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */
126 at91_pio3_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */
127 at91_pio3_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */
128 at91_pio3_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */
129 at91_pio3_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */
130 at91_pio3_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */
131 at91_pio3_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */
132 at91_pio3_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */
133 at91_pio3_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */
136 at91_periph_clk_enable(ATMEL_ID_GMAC0);
139 at91_set_pio_output(AT91_PIO_PORTE, 8, 1);
143 static void vinco_serial3_hw_init(void)
145 at91_pio3_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */
146 at91_pio3_set_b_periph(AT91_PIO_PORTE, 16, 0); /* RXD3 */
149 at91_periph_clk_enable(ATMEL_ID_USART3);
152 int board_early_init_f(void)
154 at91_periph_clk_enable(ATMEL_ID_PIOA);
155 at91_periph_clk_enable(ATMEL_ID_PIOB);
156 at91_periph_clk_enable(ATMEL_ID_PIOC);
157 at91_periph_clk_enable(ATMEL_ID_PIOD);
158 at91_periph_clk_enable(ATMEL_ID_PIOE);
160 vinco_serial3_hw_init();
167 /* adress of boot parameters */
168 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
170 #ifndef CONFIG_DM_SPI
171 vinco_spi0_hw_init();
174 #ifdef CONFIG_GENERIC_ATMEL_MCI
175 vinco_mci0_hw_init();
178 vinco_macb0_hw_init();
180 #ifdef CONFIG_CMD_USB
183 #ifdef CONFIG_USB_GADGET_ATMEL_USBA
192 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
193 CONFIG_SYS_SDRAM_SIZE);
197 int board_eth_init(bd_t *bis)
202 rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
205 #ifdef CONFIG_USB_GADGET_ATMEL_USBA
206 usba_udc_probe(&pdata);
207 #ifdef CONFIG_USB_ETH_RNDIS
208 usb_eth_initialize(bis);