board/freescale/mx6slevk/mx6slevk.c

   1 /*
   2  * Copyright (C) 2013 Freescale Semiconductor, Inc.
   3  *
   4  * Author: Fabio Estevam <fabio.estevam@freescale.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <asm/arch/clock.h>
  10 #include <asm/arch/iomux.h>
  11 #include <asm/arch/crm_regs.h>
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/arch/mx6-ddr.h>
  14 #include <asm/arch/mx6-pins.h>
  15 #include <asm/arch/sys_proto.h>
  16 #include <asm/gpio.h>
  17 #include <asm/mach-imx/iomux-v3.h>
  18 #include <asm/mach-imx/mxc_i2c.h>
  19 #include <asm/mach-imx/spi.h>
  20 #include <asm/io.h>
  21 #include <linux/sizes.h>
  22 #include <common.h>
  23 #include <fsl_esdhc.h>
  24 #include <i2c.h>
  25 #include <mmc.h>
  26 #include <netdev.h>
  27 #include <power/pmic.h>
  28 #include <power/pfuze100_pmic.h>
  29 #include "../common/pfuze.h"
  30
  31 DECLARE_GLOBAL_DATA_PTR;
  32
  33 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  34         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |                 \
  35         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  36
  37 #define USDHC_PAD_CTRL (PAD_CTL_PUS_22K_UP |                    \
  38         PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |                 \
  39         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  40
  41 #define ENET_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
  42         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |             \
  43         PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
  44
  45 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
  46                       PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
  47
  48 #define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
  49                         PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\
  50                         PAD_CTL_DSE_80ohm | PAD_CTL_HYS |       \
  51                         PAD_CTL_SRE_FAST)
  52
  53 #define ETH_PHY_POWER   IMX_GPIO_NR(4, 21)
  54
  55 int dram_init(void)
  56 {
  57         gd->ram_size = imx_ddr_size();
  58
  59         return 0;
  60 }
  61
  62 static iomux_v3_cfg_t const uart1_pads[] = {
  63         MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
  64         MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
  65 };
  66
  67 #ifdef CONFIG_SPL_BUILD
  68 static iomux_v3_cfg_t const usdhc1_pads[] = {
  69         /* 8 bit SD */
  70         MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  71         MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  72         MX6_PAD_SD1_DAT0__USDHC1_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  73         MX6_PAD_SD1_DAT1__USDHC1_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  74         MX6_PAD_SD1_DAT2__USDHC1_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  75         MX6_PAD_SD1_DAT3__USDHC1_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  76         MX6_PAD_SD1_DAT4__USDHC1_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  77         MX6_PAD_SD1_DAT5__USDHC1_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  78         MX6_PAD_SD1_DAT6__USDHC1_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  79         MX6_PAD_SD1_DAT7__USDHC1_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  80
  81         /*CD pin*/
  82         MX6_PAD_KEY_ROW7__GPIO_4_7 | MUX_PAD_CTRL(NO_PAD_CTRL),
  83 };
  84
  85 static iomux_v3_cfg_t const usdhc2_pads[] = {
  86         MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  87         MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  88         MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  89         MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  90         MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  91         MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  92
  93         /*CD pin*/
  94         MX6_PAD_SD2_DAT7__GPIO_5_0 | MUX_PAD_CTRL(NO_PAD_CTRL),
  95 };
  96
  97 static iomux_v3_cfg_t const usdhc3_pads[] = {
  98         MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  99         MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 100         MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 101         MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 102         MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 103         MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 104
 105         /*CD pin*/
 106         MX6_PAD_REF_CLK_32K__GPIO_3_22 | MUX_PAD_CTRL(NO_PAD_CTRL),
 107 };
 108 #endif
 109
 110 static iomux_v3_cfg_t const fec_pads[] = {
 111         MX6_PAD_FEC_MDC__FEC_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 112         MX6_PAD_FEC_MDIO__FEC_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
 113         MX6_PAD_FEC_CRS_DV__FEC_RX_DV | MUX_PAD_CTRL(ENET_PAD_CTRL),
 114         MX6_PAD_FEC_RXD0__FEC_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 115         MX6_PAD_FEC_RXD1__FEC_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 116         MX6_PAD_FEC_TX_EN__FEC_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
 117         MX6_PAD_FEC_TXD0__FEC_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 118         MX6_PAD_FEC_TXD1__FEC_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 119         MX6_PAD_FEC_REF_CLK__FEC_REF_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL),
 120         MX6_PAD_FEC_RX_ER__GPIO_4_19 | MUX_PAD_CTRL(NO_PAD_CTRL),
 121         MX6_PAD_FEC_TX_CLK__GPIO_4_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
 122 };
 123
 124 #ifdef CONFIG_MXC_SPI
 125 static iomux_v3_cfg_t ecspi1_pads[] = {
 126         MX6_PAD_ECSPI1_MISO__ECSPI_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
 127         MX6_PAD_ECSPI1_MOSI__ECSPI_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
 128         MX6_PAD_ECSPI1_SCLK__ECSPI_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
 129         MX6_PAD_ECSPI1_SS0__GPIO4_IO11  | MUX_PAD_CTRL(NO_PAD_CTRL),
 130 };
 131
 132 int board_spi_cs_gpio(unsigned bus, unsigned cs)
 133 {
 134         return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1;
 135 }
 136
 137 static void setup_spi(void)
 138 {
 139         imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
 140 }
 141 #endif
 142
 143 static void setup_iomux_uart(void)
 144 {
 145         imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
 146 }
 147
 148 static void setup_iomux_fec(void)
 149 {
 150         imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
 151
 152         /* Power up LAN8720 PHY */
 153         gpio_request(ETH_PHY_POWER, "eth_pwr");
 154         gpio_direction_output(ETH_PHY_POWER , 1);
 155         udelay(15000);
 156 }
 157
 158 int board_mmc_get_env_dev(int devno)
 159 {
 160         return devno;
 161 }
 162
 163 #ifdef CONFIG_DM_PMIC_PFUZE100
 164 int power_init_board(void)
 165 {
 166         struct udevice *dev;
 167         int ret;
 168         u32 dev_id, rev_id, i;
 169         u32 switch_num = 6;
 170         u32 offset = PFUZE100_SW1CMODE;
 171
 172         ret = pmic_get("pfuze100", &dev);
 173         if (ret == -ENODEV)
 174                 return 0;
 175
 176         if (ret != 0)
 177                 return ret;
 178
 179         dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
 180         rev_id = pmic_reg_read(dev, PFUZE100_REVID);
 181         printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
 182
 183         /* set SW1AB staby volatage 0.975V */
 184         pmic_clrsetbits(dev, PFUZE100_SW1ABSTBY, 0x3f, 0x1b);
 185
 186         /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
 187         pmic_clrsetbits(dev, PFUZE100_SW1ABCONF, 0xc0, 0x40);
 188
 189         /* set SW1C staby volatage 0.975V */
 190         pmic_clrsetbits(dev, PFUZE100_SW1CSTBY, 0x3f, 0x1b);
 191
 192         /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
 193         pmic_clrsetbits(dev, PFUZE100_SW1CCONF, 0xc0, 0x40);
 194
 195         /* Init mode to APS_PFM */
 196         pmic_reg_write(dev, PFUZE100_SW1ABMODE, APS_PFM);
 197
 198         for (i = 0; i < switch_num - 1; i++)
 199                 pmic_reg_write(dev, offset + i * SWITCH_SIZE, APS_PFM);
 200
 201         return 0;
 202 }
 203 #endif
 204
 205 #ifdef CONFIG_FEC_MXC
 206 int board_eth_init(bd_t *bis)
 207 {
 208         setup_iomux_fec();
 209
 210         return cpu_eth_init(bis);
 211 }
 212
 213 static int setup_fec(void)
 214 {
 215         struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
 216
 217         /* clear gpr1[14], gpr1[18:17] to select anatop clock */
 218         clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);
 219
 220         return enable_fec_anatop_clock(0, ENET_50MHZ);
 221 }
 222 #endif
 223
 224 int board_early_init_f(void)
 225 {
 226         setup_iomux_uart();
 227
 228         return 0;
 229 }
 230
 231 int board_init(void)
 232 {
 233         /* address of boot parameters */
 234         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 235
 236 #ifdef CONFIG_MXC_SPI
 237         gpio_request(IMX_GPIO_NR(4, 11), "spi_cs");
 238         setup_spi();
 239 #endif
 240
 241 #ifdef  CONFIG_FEC_MXC
 242         setup_fec();
 243 #endif
 244
 245         return 0;
 246 }
 247
 248 int checkboard(void)
 249 {
 250         puts("Board: MX6SLEVK\n");
 251
 252         return 0;
 253 }
 254
 255 #ifdef CONFIG_SPL_BUILD
 256 #include <spl.h>
 257 #include <libfdt.h>
 258
 259 #define USDHC1_CD_GPIO  IMX_GPIO_NR(4, 7)
 260 #define USDHC2_CD_GPIO  IMX_GPIO_NR(5, 0)
 261 #define USDHC3_CD_GPIO  IMX_GPIO_NR(3, 22)
 262
 263 static struct fsl_esdhc_cfg usdhc_cfg[3] = {
 264         {USDHC1_BASE_ADDR},
 265         {USDHC2_BASE_ADDR, 0, 4},
 266         {USDHC3_BASE_ADDR, 0, 4},
 267 };
 268
 269 int board_mmc_getcd(struct mmc *mmc)
 270 {
 271         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 272         int ret = 0;
 273
 274         switch (cfg->esdhc_base) {
 275         case USDHC1_BASE_ADDR:
 276                 gpio_request(USDHC1_CD_GPIO, "cd1_gpio");
 277                 ret = !gpio_get_value(USDHC1_CD_GPIO);
 278                 break;
 279         case USDHC2_BASE_ADDR:
 280                 gpio_request(USDHC2_CD_GPIO, "cd2_gpio");
 281                 ret = !gpio_get_value(USDHC2_CD_GPIO);
 282                 break;
 283         case USDHC3_BASE_ADDR:
 284                 gpio_request(USDHC3_CD_GPIO, "cd3_gpio");
 285                 ret = !gpio_get_value(USDHC3_CD_GPIO);
 286                 break;
 287         }
 288
 289         return ret;
 290 }
 291
 292 int board_mmc_init(bd_t *bis)
 293 {
 294         struct src *src_regs = (struct src *)SRC_BASE_ADDR;
 295         u32 val;
 296         u32 port;
 297
 298         val = readl(&src_regs->sbmr1);
 299
 300         /* Boot from USDHC */
 301         port = (val >> 11) & 0x3;
 302         switch (port) {
 303         case 0:
 304                 imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
 305                                                  ARRAY_SIZE(usdhc1_pads));
 306                 gpio_direction_input(USDHC1_CD_GPIO);
 307                 usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
 308                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 309                 break;
 310         case 1:
 311                 imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
 312                                                  ARRAY_SIZE(usdhc2_pads));
 313                 gpio_direction_input(USDHC2_CD_GPIO);
 314                 usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
 315                 usdhc_cfg[0].max_bus_width = 4;
 316                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 317                 break;
 318         case 2:
 319                 imx_iomux_v3_setup_multiple_pads(usdhc3_pads,
 320                                                  ARRAY_SIZE(usdhc3_pads));
 321                 gpio_direction_input(USDHC3_CD_GPIO);
 322                 usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
 323                 usdhc_cfg[0].max_bus_width = 4;
 324                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 325                 break;
 326         }
 327
 328         gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
 329         return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
 330 }
 331
 332 const struct mx6sl_iomux_ddr_regs mx6_ddr_ioregs = {
 333         .dram_sdqs0 = 0x00003030,
 334         .dram_sdqs1 = 0x00003030,
 335         .dram_sdqs2 = 0x00003030,
 336         .dram_sdqs3 = 0x00003030,
 337         .dram_dqm0 = 0x00000030,
 338         .dram_dqm1 = 0x00000030,
 339         .dram_dqm2 = 0x00000030,
 340         .dram_dqm3 = 0x00000030,
 341         .dram_cas  = 0x00000030,
 342         .dram_ras  = 0x00000030,
 343         .dram_sdclk_0 = 0x00000028,
 344         .dram_reset = 0x00000030,
 345         .dram_sdba2 = 0x00000000,
 346         .dram_odt0 = 0x00000008,
 347         .dram_odt1 = 0x00000008,
 348 };
 349
 350 const struct mx6sl_iomux_grp_regs mx6_grp_ioregs = {
 351         .grp_b0ds = 0x00000030,
 352         .grp_b1ds = 0x00000030,
 353         .grp_b2ds = 0x00000030,
 354         .grp_b3ds = 0x00000030,
 355         .grp_addds = 0x00000030,
 356         .grp_ctlds = 0x00000030,
 357         .grp_ddrmode_ctl = 0x00020000,
 358         .grp_ddrpke = 0x00000000,
 359         .grp_ddrmode = 0x00020000,
 360         .grp_ddr_type = 0x00080000,
 361 };
 362
 363 const struct mx6_mmdc_calibration mx6_mmcd_calib = {
 364         .p0_mpdgctrl0 =  0x20000000,
 365         .p0_mpdgctrl1 =  0x00000000,
 366         .p0_mprddlctl =  0x4241444a,
 367         .p0_mpwrdlctl =  0x3030312b,
 368         .mpzqlp2ctl = 0x1b4700c7,
 369 };
 370
 371 static struct mx6_lpddr2_cfg mem_ddr = {
 372         .mem_speed = 800,
 373         .density = 4,
 374         .width = 32,
 375         .banks = 8,
 376         .rowaddr = 14,
 377         .coladdr = 10,
 378         .trcd_lp = 2000,
 379         .trppb_lp = 2000,
 380         .trpab_lp = 2250,
 381         .trasmin = 4200,
 382 };
 383
 384 static void ccgr_init(void)
 385 {
 386         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 387
 388         writel(0xFFFFFFFF, &ccm->CCGR0);
 389         writel(0xFFFFFFFF, &ccm->CCGR1);
 390         writel(0xFFFFFFFF, &ccm->CCGR2);
 391         writel(0xFFFFFFFF, &ccm->CCGR3);
 392         writel(0xFFFFFFFF, &ccm->CCGR4);
 393         writel(0xFFFFFFFF, &ccm->CCGR5);
 394         writel(0xFFFFFFFF, &ccm->CCGR6);
 395
 396         writel(0x00260324, &ccm->cbcmr);
 397 }
 398
 399 static void spl_dram_init(void)
 400 {
 401         struct mx6_ddr_sysinfo sysinfo = {
 402                 .dsize = mem_ddr.width / 32,
 403                 .cs_density = 20,
 404                 .ncs = 2,
 405                 .cs1_mirror = 0,
 406                 .walat = 0,
 407                 .ralat = 2,
 408                 .mif3_mode = 3,
 409                 .bi_on = 1,
 410                 .rtt_wr = 0,        /* LPDDR2 does not need rtt_wr rtt_nom */
 411                 .rtt_nom = 0,
 412                 .sde_to_rst = 0,    /* LPDDR2 does not need this field */
 413                 .rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */
 414                 .ddr_type = DDR_TYPE_LPDDR2,
 415                 .refsel = 0,    /* Refresh cycles at 64KHz */
 416                 .refr = 3,      /* 4 refresh commands per refresh cycle */
 417         };
 418         mx6sl_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs);
 419         mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
 420 }
 421
 422 void board_init_f(ulong dummy)
 423 {
 424         /* setup AIPS and disable watchdog */
 425         arch_cpu_init();
 426
 427         ccgr_init();
 428
 429         /* iomux and setup of i2c */
 430         board_early_init_f();
 431
 432         /* setup GP timer */
 433         timer_init();
 434
 435         /* UART clocks enabled and gd valid - init serial console */
 436         preloader_console_init();
 437
 438         /* DDR initialization */
 439         spl_dram_init();
 440
 441         /* Clear the BSS. */
 442         memset(__bss_start, 0, __bss_end - __bss_start);
 443
 444         /* load/boot image from boot device */
 445         board_init_r(NULL, 0);
 446 }
 447 #endif