board/BuR/brppt2/board.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Board functions for BuR BRPPT2 board
   4  *
   5  * Copyright (C) 2019
   6  * B&R Industrial Automation GmbH - http://www.br-automation.com/
   7  *
   8  */
   9 #include <common.h>
  10 #include <cpu_func.h>
  11 #include <spl.h>
  12 #include <dm.h>
  13 #include <miiphy.h>
  14 #include <asm/arch/crm_regs.h>
  15 #include <asm/arch/sys_proto.h>
  16 #include <asm/arch/iomux.h>
  17 #include <asm/arch/mx6-pins.h>
  18 #ifdef CONFIG_SPL_BUILD
  19 # include <asm/arch/mx6-ddr.h>
  20 #endif
  21 #include <asm/arch/clock.h>
  22 #include <asm/io.h>
  23 #include <asm/gpio.h>
  24
  25 #define USBHUB_RSTN     IMX_GPIO_NR(1, 16)
  26 #define BKLT_EN         IMX_GPIO_NR(1, 15)
  27 #define CAPT_INT        IMX_GPIO_NR(4, 9)
  28 #define CAPT_RESETN     IMX_GPIO_NR(4, 11)
  29 #define SW_INTN         IMX_GPIO_NR(3, 26)
  30 #define VCCDISP_EN      IMX_GPIO_NR(5, 18)
  31 #define EMMC_RSTN       IMX_GPIO_NR(6, 8)
  32 #define PMIC_IRQN       IMX_GPIO_NR(5, 22)
  33 #define TASTER          IMX_GPIO_NR(5, 23)
  34
  35 #define ETH0_LINK       IMX_GPIO_NR(1, 27)
  36 #define ETH1_LINK       IMX_GPIO_NR(1, 28)
  37
  38 #define UART_PAD_CTRL           (PAD_CTL_PUS_47K_UP |                   \
  39                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  40                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  41
  42 #define I2C_PAD_CTRL            (PAD_CTL_PUS_47K_UP |                   \
  43                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  44                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  45
  46 #define ECSPI_PAD_CTRL          (PAD_CTL_PUS_100K_DOWN |                \
  47                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_48ohm | \
  48                                 PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  49 #define USDHC_PAD_CTRL          (PAD_CTL_PUS_47K_UP |                   \
  50                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  51                                 PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  52
  53 #define ENET_PAD_CTRL           (PAD_CTL_PUS_100K_UP |                  \
  54                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
  55                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  56
  57 #define ENET_PAD_CTRL1          (PAD_CTL_PUS_100K_UP |                  \
  58                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_34ohm | \
  59                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  60
  61 #define ENET_PAD_CTRL_PU        (PAD_CTL_PUS_100K_UP |          \
  62                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm | \
  63                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  64
  65 #define ENET_PAD_CTRL_CLK       ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
  66                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
  67                                 PAD_CTL_SRE_FAST)
  68
  69 #define GPIO_PAD_CTRL_PU        (PAD_CTL_PUS_100K_UP |                  \
  70                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  71                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  72
  73 #define GPIO_PAD_CTRL_PD        (PAD_CTL_PUS_100K_DOWN |                \
  74                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  75                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  76
  77 #define LCDCMOS_PAD_CTRL        (PAD_CTL_PUS_100K_DOWN |                \
  78                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm |\
  79                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  80
  81 #define MUXDESC(pad, ctrl)      IOMUX_PADS(pad | MUX_PAD_CTRL(ctrl))
  82
  83 #if !defined(CONFIG_SPL_BUILD)
  84 static iomux_v3_cfg_t const eth_pads[] = {
  85         /*
  86          * Gigabit Ethernet
  87          */
  88         /* CLKs */
  89         MUXDESC(PAD_GPIO_16__ENET_REF_CLK,      ENET_PAD_CTRL_CLK),
  90         MUXDESC(PAD_ENET_REF_CLK__ENET_TX_CLK,  ENET_PAD_CTRL_CLK),
  91         /* MDIO */
  92         MUXDESC(PAD_ENET_MDIO__ENET_MDIO,       ENET_PAD_CTRL_PU),
  93         MUXDESC(PAD_ENET_MDC__ENET_MDC,         ENET_PAD_CTRL_PU),
  94         /* RGMII */
  95         MUXDESC(PAD_RGMII_TXC__RGMII_TXC,       ENET_PAD_CTRL1),
  96         MUXDESC(PAD_RGMII_TD0__RGMII_TD0,       ENET_PAD_CTRL),
  97         MUXDESC(PAD_RGMII_TD1__RGMII_TD1,       ENET_PAD_CTRL),
  98         MUXDESC(PAD_RGMII_TD2__RGMII_TD2,       ENET_PAD_CTRL),
  99         MUXDESC(PAD_RGMII_TD3__RGMII_TD3,       ENET_PAD_CTRL),
 100         MUXDESC(PAD_RGMII_TX_CTL__RGMII_TX_CTL, ENET_PAD_CTRL),
 101         MUXDESC(PAD_RGMII_RXC__RGMII_RXC,       ENET_PAD_CTRL_PU),
 102         MUXDESC(PAD_RGMII_RD0__RGMII_RD0,       ENET_PAD_CTRL_PU),
 103         MUXDESC(PAD_RGMII_RD1__RGMII_RD1,       ENET_PAD_CTRL_PU),
 104         MUXDESC(PAD_RGMII_RD2__RGMII_RD2,       ENET_PAD_CTRL_PU),
 105         MUXDESC(PAD_RGMII_RD3__RGMII_RD3,       ENET_PAD_CTRL_PU),
 106         MUXDESC(PAD_RGMII_RX_CTL__RGMII_RX_CTL, ENET_PAD_CTRL_PU),
 107         /* ETH0_LINK */
 108         MUXDESC(PAD_ENET_RXD0__GPIO1_IO27,      GPIO_PAD_CTRL_PD),
 109         /* ETH1_LINK */
 110         MUXDESC(PAD_ENET_TX_EN__GPIO1_IO28,     GPIO_PAD_CTRL_PD),
 111 };
 112
 113 static iomux_v3_cfg_t const board_pads[] = {
 114         /*
 115          * I2C #3, #4
 116          */
 117         MUXDESC(PAD_GPIO_3__I2C3_SCL,           I2C_PAD_CTRL),
 118         MUXDESC(PAD_GPIO_6__I2C3_SDA,           I2C_PAD_CTRL),
 119
 120         /*
 121          * UART#4 PADS
 122          * UART_Tasten
 123          */
 124         MUXDESC(PAD_CSI0_DAT12__UART4_TX_DATA,  UART_PAD_CTRL),
 125         MUXDESC(PAD_CSI0_DAT13__UART4_RX_DATA,  UART_PAD_CTRL),
 126         MUXDESC(PAD_CSI0_DAT17__UART4_CTS_B,    UART_PAD_CTRL),
 127         MUXDESC(PAD_CSI0_DAT16__UART4_RTS_B,    UART_PAD_CTRL),
 128         /*
 129          * ESCPI#1
 130          * M25P32 NOR-Flash
 131          */
 132         MUXDESC(PAD_EIM_D16__ECSPI1_SCLK,       ECSPI_PAD_CTRL),
 133         MUXDESC(PAD_EIM_D17__ECSPI1_MISO,       ECSPI_PAD_CTRL),
 134         MUXDESC(PAD_EIM_D18__ECSPI1_MOSI,       ECSPI_PAD_CTRL),
 135         MUXDESC(PAD_EIM_D19__GPIO3_IO19,        ECSPI_PAD_CTRL),
 136         /*
 137          * ESCPI#2
 138          * resTouch SPI ADC
 139          */
 140         MUXDESC(PAD_CSI0_DAT8__ECSPI2_SCLK,     ECSPI_PAD_CTRL),
 141         MUXDESC(PAD_EIM_OE__ECSPI2_MISO,        ECSPI_PAD_CTRL),
 142         MUXDESC(PAD_CSI0_DAT9__ECSPI2_MOSI,     ECSPI_PAD_CTRL),
 143         MUXDESC(PAD_EIM_D24__GPIO3_IO24,        ECSPI_PAD_CTRL),
 144         /*
 145          * USDHC#4
 146          */
 147         MUXDESC(PAD_SD4_CLK__SD4_CLK,           USDHC_PAD_CTRL),
 148         MUXDESC(PAD_SD4_CMD__SD4_CMD,           USDHC_PAD_CTRL),
 149         MUXDESC(PAD_SD4_DAT0__SD4_DATA0,        USDHC_PAD_CTRL),
 150         MUXDESC(PAD_SD4_DAT1__SD4_DATA1,        USDHC_PAD_CTRL),
 151         MUXDESC(PAD_SD4_DAT2__SD4_DATA2,        USDHC_PAD_CTRL),
 152         MUXDESC(PAD_SD4_DAT3__SD4_DATA3,        USDHC_PAD_CTRL),
 153         MUXDESC(PAD_SD4_DAT4__SD4_DATA4,        USDHC_PAD_CTRL),
 154         MUXDESC(PAD_SD4_DAT5__SD4_DATA5,        USDHC_PAD_CTRL),
 155         MUXDESC(PAD_SD4_DAT6__SD4_DATA6,        USDHC_PAD_CTRL),
 156         MUXDESC(PAD_SD4_DAT7__SD4_DATA7,        USDHC_PAD_CTRL),
 157         /*
 158          * USB OTG power & ID
 159          */
 160         /* USB_OTG_5V_EN */
 161         MUXDESC(PAD_EIM_D22__GPIO3_IO22,        GPIO_PAD_CTRL_PD),
 162         MUXDESC(PAD_EIM_D31__GPIO3_IO31,        GPIO_PAD_CTRL_PD),
 163         /* USB_OTG_JUMPER */
 164         MUXDESC(PAD_ENET_RX_ER__USB_OTG_ID,     GPIO_PAD_CTRL_PD),
 165         /*
 166          * PWM-Pins
 167          */
 168         /* BKLT_CTL */
 169         MUXDESC(PAD_SD1_CMD__PWM4_OUT,          GPIO_PAD_CTRL_PD),
 170         /* SPEAKER */
 171         MUXDESC(PAD_SD1_DAT1__PWM3_OUT,         GPIO_PAD_CTRL_PD),
 172         /*
 173          * GPIOs
 174          */
 175         /* USB_HUB_nRESET */
 176         MUXDESC(PAD_SD1_DAT0__GPIO1_IO16,       GPIO_PAD_CTRL_PD),
 177         /* BKLT_EN */
 178         MUXDESC(PAD_SD2_DAT0__GPIO1_IO15,       GPIO_PAD_CTRL_PD),
 179         /* capTouch_INT */
 180         MUXDESC(PAD_KEY_ROW1__GPIO4_IO09,       GPIO_PAD_CTRL_PD),
 181         /* capTouch_nRESET */
 182         MUXDESC(PAD_KEY_ROW2__GPIO4_IO11,       GPIO_PAD_CTRL_PD),
 183         /* SW_nINT */
 184         MUXDESC(PAD_EIM_D26__GPIO3_IO26,        GPIO_PAD_CTRL_PU),
 185         /* VCC_DISP_EN */
 186         MUXDESC(PAD_CSI0_PIXCLK__GPIO5_IO18,    GPIO_PAD_CTRL_PD),
 187         /* eMMC_nRESET */
 188         MUXDESC(PAD_NANDF_ALE__GPIO6_IO08,      GPIO_PAD_CTRL_PD),
 189         /* HWID*/
 190         MUXDESC(PAD_NANDF_D0__GPIO2_IO00,       GPIO_PAD_CTRL_PU),
 191         MUXDESC(PAD_NANDF_D1__GPIO2_IO01,       GPIO_PAD_CTRL_PU),
 192         MUXDESC(PAD_NANDF_D2__GPIO2_IO02,       GPIO_PAD_CTRL_PU),
 193         MUXDESC(PAD_NANDF_D3__GPIO2_IO03,       GPIO_PAD_CTRL_PU),
 194         /* PMIC_nIRQ */
 195         MUXDESC(PAD_CSI0_DAT4__GPIO5_IO22,      GPIO_PAD_CTRL_PU),
 196         /* nTASTER */
 197         MUXDESC(PAD_CSI0_DAT5__GPIO5_IO23,      GPIO_PAD_CTRL_PU),
 198         /* RGB LCD Display */
 199         MUXDESC(PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,    LCDCMOS_PAD_CTRL),
 200         MUXDESC(PAD_DI0_PIN2__IPU1_DI0_PIN02,           LCDCMOS_PAD_CTRL),
 201         MUXDESC(PAD_DI0_PIN3__IPU1_DI0_PIN03,           LCDCMOS_PAD_CTRL),
 202         MUXDESC(PAD_DI0_PIN4__IPU1_DI0_PIN04,           LCDCMOS_PAD_CTRL),
 203         MUXDESC(PAD_DI0_PIN15__IPU1_DI0_PIN15,          LCDCMOS_PAD_CTRL),
 204         MUXDESC(PAD_DISP0_DAT0__IPU1_DISP0_DATA00,      LCDCMOS_PAD_CTRL),
 205         MUXDESC(PAD_DISP0_DAT1__IPU1_DISP0_DATA01,      LCDCMOS_PAD_CTRL),
 206         MUXDESC(PAD_DISP0_DAT2__IPU1_DISP0_DATA02,      LCDCMOS_PAD_CTRL),
 207         MUXDESC(PAD_DISP0_DAT3__IPU1_DISP0_DATA03,      LCDCMOS_PAD_CTRL),
 208         MUXDESC(PAD_DISP0_DAT4__IPU1_DISP0_DATA04,      LCDCMOS_PAD_CTRL),
 209         MUXDESC(PAD_DISP0_DAT5__IPU1_DISP0_DATA05,      LCDCMOS_PAD_CTRL),
 210         MUXDESC(PAD_DISP0_DAT6__IPU1_DISP0_DATA06,      LCDCMOS_PAD_CTRL),
 211         MUXDESC(PAD_DISP0_DAT7__IPU1_DISP0_DATA07,      LCDCMOS_PAD_CTRL),
 212         MUXDESC(PAD_DISP0_DAT8__IPU1_DISP0_DATA08,      LCDCMOS_PAD_CTRL),
 213         MUXDESC(PAD_DISP0_DAT9__IPU1_DISP0_DATA09,      LCDCMOS_PAD_CTRL),
 214         MUXDESC(PAD_DISP0_DAT10__IPU1_DISP0_DATA10,     LCDCMOS_PAD_CTRL),
 215         MUXDESC(PAD_DISP0_DAT11__IPU1_DISP0_DATA11,     LCDCMOS_PAD_CTRL),
 216         MUXDESC(PAD_DISP0_DAT12__IPU1_DISP0_DATA12,     LCDCMOS_PAD_CTRL),
 217         MUXDESC(PAD_DISP0_DAT13__IPU1_DISP0_DATA13,     LCDCMOS_PAD_CTRL),
 218         MUXDESC(PAD_DISP0_DAT14__IPU1_DISP0_DATA14,     LCDCMOS_PAD_CTRL),
 219         MUXDESC(PAD_DISP0_DAT15__IPU1_DISP0_DATA15,     LCDCMOS_PAD_CTRL),
 220         MUXDESC(PAD_DISP0_DAT16__IPU1_DISP0_DATA16,     LCDCMOS_PAD_CTRL),
 221         MUXDESC(PAD_DISP0_DAT17__IPU1_DISP0_DATA17,     LCDCMOS_PAD_CTRL),
 222         MUXDESC(PAD_DISP0_DAT18__IPU1_DISP0_DATA18,     LCDCMOS_PAD_CTRL),
 223         MUXDESC(PAD_DISP0_DAT19__IPU1_DISP0_DATA19,     LCDCMOS_PAD_CTRL),
 224         MUXDESC(PAD_DISP0_DAT20__IPU1_DISP0_DATA20,     LCDCMOS_PAD_CTRL),
 225         MUXDESC(PAD_DISP0_DAT21__IPU1_DISP0_DATA21,     LCDCMOS_PAD_CTRL),
 226         MUXDESC(PAD_DISP0_DAT22__IPU1_DISP0_DATA22,     LCDCMOS_PAD_CTRL),
 227         MUXDESC(PAD_DISP0_DAT23__IPU1_DISP0_DATA23,     LCDCMOS_PAD_CTRL),
 228 };
 229
 230 int board_ehci_hcd_init(int port)
 231 {
 232         gpio_direction_output(USBHUB_RSTN, 1);
 233
 234         return 0;
 235 }
 236
 237 int board_late_init(void)
 238 {
 239         ulong b_mode = 4;
 240
 241         if (gpio_get_value(TASTER) == 0)
 242                 b_mode = 12;
 243
 244         env_set_ulong("b_mode", b_mode);
 245
 246         return 0;
 247 }
 248
 249 int board_init(void)
 250 {
 251         gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 252
 253         if (gpio_request(BKLT_EN, "BKLT_EN"))
 254                 printf("Warning: BKLT_EN setup failed\n");
 255         gpio_direction_output(BKLT_EN, 0);
 256
 257         if (gpio_request(USBHUB_RSTN, "USBHUB_nRST"))
 258                 printf("Warning: USBHUB_nRST setup failed\n");
 259         gpio_direction_output(USBHUB_RSTN, 0);
 260
 261         if (gpio_request(TASTER, "TASTER"))
 262                 printf("Warning: TASTER setup failed\n");
 263         gpio_direction_input(TASTER);
 264
 265         return 0;
 266 }
 267
 268 int board_early_init_f(void)
 269 {
 270         struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
 271
 272         SETUP_IOMUX_PADS(board_pads);
 273         SETUP_IOMUX_PADS(eth_pads);
 274
 275         /* set GPIO_16 as ENET_REF_CLK_OUT running at 25 MHz */
 276         setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
 277         enable_fec_anatop_clock(0, ENET_25MHZ);
 278         enable_enet_clk(1);
 279
 280         return 0;
 281 }
 282
 283 int dram_init(void)
 284 {
 285         gd->ram_size = imx_ddr_size();
 286
 287         return 0;
 288 }
 289 #else
 290 /* configure MX6SOLO/DUALLITE mmdc DDR io registers */
 291 static struct mx6sdl_iomux_ddr_regs ddr_iomux_s = {
 292         /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
 293         .dram_sdclk_0           = 0x00020030,
 294         .dram_sdclk_1           = 0x00020030,
 295         .dram_cas               = 0x00020030,
 296         .dram_ras               = 0x00020030,
 297         .dram_reset             = 0x00020030,
 298         /* SDCKE[0:1]: 100k pull-up */
 299         .dram_sdcke0            = 0x00003000,
 300         .dram_sdcke1            = 0x00003000,
 301         /* SDBA2: pull-up disabled */
 302         .dram_sdba2             = 0x00000000,
 303         /* SDODT[0:1]: 100k pull-up, 40 ohm */
 304         .dram_sdodt0            = 0x00003030,
 305         .dram_sdodt1            = 0x00003030,
 306         /* SDQS[0:7]: Differential input, 40 ohm */
 307         .dram_sdqs0             = 0x00000030,
 308         .dram_sdqs1             = 0x00000030,
 309         .dram_sdqs2             = 0x00000030,
 310         .dram_sdqs3             = 0x00000030,
 311         .dram_sdqs4             = 0x00000030,
 312         .dram_sdqs5             = 0x00000030,
 313         .dram_sdqs6             = 0x00000030,
 314         .dram_sdqs7             = 0x00000030,
 315         /* DQM[0:7]: Differential input, 40 ohm */
 316         .dram_dqm0              = 0x00020030,
 317         .dram_dqm1              = 0x00020030,
 318         .dram_dqm2              = 0x00020030,
 319         .dram_dqm3              = 0x00020030,
 320         .dram_dqm4              = 0x00020030,
 321         .dram_dqm5              = 0x00020030,
 322         .dram_dqm6              = 0x00020030,
 323         .dram_dqm7              = 0x00020030,
 324 };
 325
 326 /* configure MX6SOLO/DUALLITE mmdc GRP io registers */
 327 static struct mx6sdl_iomux_grp_regs grp_iomux_s = {
 328         /* DDR3 */
 329         .grp_ddr_type           = 0x000c0000,
 330         .grp_ddrmode_ctl        = 0x00020000,
 331         /* disable DDR pullups */
 332         .grp_ddrpke             = 0x00000000,
 333         /* ADDR[00:16], SDBA[0:1]: 40 ohm */
 334         .grp_addds              = 0x00000030,
 335         /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
 336         .grp_ctlds              = 0x00000030,
 337         /* DATA[00:63]: Differential input, 40 ohm */
 338         .grp_ddrmode            = 0x00020000,
 339         .grp_b0ds               = 0x00000030,
 340         .grp_b1ds               = 0x00000030,
 341         .grp_b2ds               = 0x00000030,
 342         .grp_b3ds               = 0x00000030,
 343         .grp_b4ds               = 0x00000030,
 344         .grp_b5ds               = 0x00000030,
 345         .grp_b6ds               = 0x00000030,
 346         .grp_b7ds               = 0x00000030,
 347 };
 348
 349 /*
 350  * DDR3 desriptions - these are the memory chips we support
 351  */
 352
 353 /* NT5CC128M16FP-DII */
 354 static struct mx6_ddr3_cfg cfg_nt5cc128m16fp_dii = {
 355         .mem_speed      = 1600,
 356         .density        = 2,
 357         .width          = 16,
 358         .banks          = 8,
 359         .rowaddr        = 14,
 360         .coladdr        = 10,
 361         .pagesz         = 2,
 362         .trcd           = 1375,
 363         .trcmin         = 4875,
 364         .trasmin        = 3500,
 365 };
 366
 367 /* measured on board TSERIES_ARM/1 V_LVDS_DL64 */
 368 static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x64_s = {
 369         /* write leveling calibration determine, MR1-value = 0x0002 */
 370         .p0_mpwldectrl0 = 0x003F003E,
 371         .p0_mpwldectrl1 = 0x003A003A,
 372         .p1_mpwldectrl0 = 0x001B001C,
 373         .p1_mpwldectrl1 = 0x00190031,
 374         /* Read DQS Gating calibration */
 375         .p0_mpdgctrl0   = 0x02640264,
 376         .p0_mpdgctrl1   = 0x02440250,
 377         .p1_mpdgctrl0   = 0x02400250,
 378         .p1_mpdgctrl1   = 0x0238023C,
 379         /* Read Calibration: DQS delay relative to DQ read access */
 380         .p0_mprddlctl   = 0x40464644,
 381         .p1_mprddlctl   = 0x464A4842,
 382         /* Write Calibration: DQ/DM delay relative to DQS write access */
 383         .p0_mpwrdlctl   = 0x38343034,
 384         .p1_mpwrdlctl   = 0x36323830,
 385 };
 386
 387 /* measured on board TSERIES_ARM/1 V_LVDS_S32 */
 388 static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x32_s = {
 389         /* write leveling calibration determine, MR1-value = 0x0002 */
 390         .p0_mpwldectrl0 = 0x00410043,
 391         .p0_mpwldectrl1 = 0x003A003C,
 392         /* Read DQS Gating calibration */
 393         .p0_mpdgctrl0   = 0x023C0244,
 394         .p0_mpdgctrl1   = 0x02240230,
 395         /* Read Calibration: DQS delay relative to DQ read access */
 396         .p0_mprddlctl   = 0x484C4A48,
 397         /* Write Calibration: DQ/DM delay relative to DQS write access */
 398         .p0_mpwrdlctl   = 0x3C363434,
 399 };
 400
 401 static void spl_dram_init(void)
 402 {
 403         struct gpio_regs *gpio = (struct gpio_regs *)GPIO2_BASE_ADDR;
 404         u32 val, dram_strap = 0;
 405         struct mx6_ddr3_cfg *mem = NULL;
 406         struct mx6_mmdc_calibration *calib = NULL;
 407         struct mx6_ddr_sysinfo sysinfo = {
 408                 /* width of data bus:0=16,1=32,2=64 */
 409                 .dsize          = -1,   /* CPU type specific (overwritten) */
 410                 /* config for full 4GB range so that get_mem_size() works */
 411                 .cs_density     = 32,   /* 32Gb per CS */
 412                 .ncs            = 1,    /* single chip select */
 413                 .cs1_mirror     = 0,
 414                 .rtt_wr         = 1,    /* DDR3_RTT_60_OHM, RTT_Wr = RZQ/4 */
 415                 .rtt_nom        = 1,    /* DDR3_RTT_60_OHM, RTT_Nom = RZQ/4 */
 416                 .walat          = 1,    /* Write additional latency */
 417                 .ralat          = 5,    /* Read additional latency */
 418                 .mif3_mode      = 3,    /* Command prediction working mode */
 419                 .bi_on          = 1,    /* Bank interleaving enabled */
 420                 .sde_to_rst     = 0x10, /* 14 cycles, 200us (JEDEC default) */
 421                 .rst_to_cke     = 0x23, /* 33 cycles, 500us (JEDEC default) */
 422                 .ddr_type       = 0,    /* DDR3 */
 423         };
 424
 425         /*
 426          * MMDC Calibration requires the following data:
 427          *  mx6_mmdc_calibration - board-specific calibration (routing delays)
 428          *     these calibration values depend on board routing, SoC, and DDR
 429          *  mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc)
 430          *  mx6_ddr_cfg - chip specific timing/layout details
 431          */
 432
 433         /* setup HWID3-2 to input */
 434         val = readl(&gpio->gpio_dir);
 435         val &= ~(0x1 << 0 | 0x1 << 1);
 436         writel(val, &gpio->gpio_dir);
 437
 438         /* read DRAM strapping from HWID3/2 (bit 1 and bit 0) */
 439         dram_strap = readl(&gpio->gpio_psr) & 0x3;
 440
 441         switch (dram_strap) {
 442         /* 1 GiB, 64 bit, 4 NT5CC128M16FP chips */
 443         case 0:
 444                 puts("DRAM strap 00\n");
 445                 mem = &cfg_nt5cc128m16fp_dii;
 446                 sysinfo.dsize = 2;
 447                 calib = &cal_nt5cc128m16fp_dii_128x64_s;
 448                 break;
 449         /* 512 MiB, 32 bit, 2 NT5CC128M16FP chips */
 450         case 1:
 451                 puts("DRAM strap 01\n");
 452                 mem = &cfg_nt5cc128m16fp_dii;
 453                 sysinfo.dsize = 1;
 454                 calib = &cal_nt5cc128m16fp_dii_128x32_s;
 455                 break;
 456         default:
 457                 printf("DRAM strap 0x%x (invalid)\n", dram_strap);
 458                 break;
 459         }
 460
 461         if (!mem) {
 462                 puts("Error: Invalid Memory Configuration\n");
 463                 hang();
 464         }
 465         if (!calib) {
 466                 puts("Error: Invalid Board Calibration Configuration\n");
 467                 hang();
 468         }
 469
 470         mx6sdl_dram_iocfg(16 << sysinfo.dsize,
 471                           &ddr_iomux_s,
 472                           &grp_iomux_s);
 473
 474         mx6_dram_cfg(&sysinfo, calib, mem);
 475 }
 476
 477 static iomux_v3_cfg_t const board_pads_spl[] = {
 478         /* UART#1 PADS */
 479         MUXDESC(PAD_CSI0_DAT10__UART1_TX_DATA,  UART_PAD_CTRL),
 480         MUXDESC(PAD_CSI0_DAT11__UART1_RX_DATA,  UART_PAD_CTRL),
 481         /* ESCPI#1 PADS */
 482         MUXDESC(PAD_EIM_D16__ECSPI1_SCLK,       ECSPI_PAD_CTRL),
 483         MUXDESC(PAD_EIM_D17__ECSPI1_MISO,       ECSPI_PAD_CTRL),
 484         MUXDESC(PAD_EIM_D18__ECSPI1_MOSI,       ECSPI_PAD_CTRL),
 485         MUXDESC(PAD_EIM_D19__GPIO3_IO19,        ECSPI_PAD_CTRL),
 486         /* USDHC#4 PADS */
 487         MUXDESC(PAD_SD4_CLK__SD4_CLK,           USDHC_PAD_CTRL),
 488         MUXDESC(PAD_SD4_CMD__SD4_CMD,           USDHC_PAD_CTRL),
 489         MUXDESC(PAD_SD4_DAT0__SD4_DATA0,        USDHC_PAD_CTRL),
 490         MUXDESC(PAD_SD4_DAT1__SD4_DATA1,        USDHC_PAD_CTRL),
 491         MUXDESC(PAD_SD4_DAT2__SD4_DATA2,        USDHC_PAD_CTRL),
 492         MUXDESC(PAD_SD4_DAT3__SD4_DATA3,        USDHC_PAD_CTRL),
 493         MUXDESC(PAD_SD4_DAT4__SD4_DATA4,        USDHC_PAD_CTRL),
 494         MUXDESC(PAD_SD4_DAT5__SD4_DATA5,        USDHC_PAD_CTRL),
 495         MUXDESC(PAD_SD4_DAT6__SD4_DATA6,        USDHC_PAD_CTRL),
 496         MUXDESC(PAD_SD4_DAT7__SD4_DATA7,        USDHC_PAD_CTRL),
 497         /* HWID*/
 498         MUXDESC(PAD_NANDF_D0__GPIO2_IO00,       GPIO_PAD_CTRL_PU),
 499         MUXDESC(PAD_NANDF_D1__GPIO2_IO01,       GPIO_PAD_CTRL_PU),
 500         MUXDESC(PAD_NANDF_D2__GPIO2_IO02,       GPIO_PAD_CTRL_PU),
 501         MUXDESC(PAD_NANDF_D3__GPIO2_IO03,       GPIO_PAD_CTRL_PU),
 502 };
 503
 504 void spl_board_init(void)
 505 {
 506         preloader_console_init();
 507 }
 508
 509 static void ccgr_init(void)
 510 {
 511         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 512
 513         /*
 514          * We don't use DMA in SPL, but we do need it in U-Boot. U-Boot
 515          * initializes DMA very early (before all board code), so the only
 516          * opportunity we have to initialize APBHDMA clocks is in SPL.
 517          * setbits_le32(&ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
 518          */
 519
 520         writel(0x00C03F3F, &ccm->CCGR0);
 521         writel(0x00F0FC03, &ccm->CCGR1);
 522         writel(0x0FFFF000, &ccm->CCGR2);
 523         writel(0x3FF00000, &ccm->CCGR3);
 524         writel(0x00FFF300, &ccm->CCGR4);
 525         writel(0x0F0030C3, &ccm->CCGR5);
 526         writel(0x000003F0, &ccm->CCGR6);
 527 }
 528
 529 void board_init_f(ulong dummy)
 530 {
 531         ccgr_init();
 532         arch_cpu_init();
 533         timer_init();
 534         gpr_init();
 535
 536         SETUP_IOMUX_PADS(board_pads_spl);
 537         spl_dram_init();
 538 }
 539
 540 void reset_cpu(ulong addr)
 541 {
 542 }
 543 #endif /* CONFIG_SPL_BUILD */