6 config SPL_LIBCOMMON_SUPPORT
9 config SPL_LIBDISK_SUPPORT
12 config SPL_LIBGENERIC_SUPPORT
15 config SPL_MMC_SUPPORT
16 default y if MMC_SDHCI_ZYNQ
18 config SPL_SERIAL_SUPPORT
21 config SPL_SPI_FLASH_SUPPORT
22 default y if ZYNQ_QSPI
24 config SPL_SPI_SUPPORT
25 default y if ZYNQ_QSPI
37 config SYS_CONFIG_NAME
38 string "Board configuration name"
39 default "xilinx_zynqmp"
41 This option contains information about board configuration name.
42 Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header
43 will be used for board configuration.
45 config SYS_MEM_RSVD_FOR_MMU
46 bool "Reserve memory for MMU Table"
48 If defined this option is used to setup different space for
49 MMU table than the one which will be allocated during
53 string "boot.bin init register filename"
57 Add register writes to boot.bin format (max 256 pairs).
58 Expect a table of register-value pairs, e.g. "0x12345678 0x4321"
60 config PMUFW_INIT_FILE
65 Include external PMUFW (Platform Management Unit FirmWare) to
66 a Xilinx bootable image (boot.bin).
69 bool "Configure ZynqMP USB"
72 bool "Disable DDR MMU mapping"
74 This option configures MMU with no DDR to avoid speculative
75 access to DDR memory where DDR is not present.
77 config SYS_MALLOC_F_LEN
80 config DEFINE_TCM_OCM_MMAP
81 bool "Define TCM and OCM memory in MMU Table"
84 This option if enabled defines the TCM and OCM memory and its
85 memory attributes in MMU table entry.
87 config ZYNQMP_PSU_INIT_ENABLED
88 bool "Include psu_init"
90 Include psu_init to full u-boot. SPL include psu_init by default.
92 config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
93 bool "Overwrite SPL bootmode"
96 Overwrite bootmode selected via boot mode pins to tell SPL what should
97 be the next boot device.
99 config ZYNQ_SDHCI_MAX_FREQ
102 config SPL_ZYNQMP_TWO_SDHCI
103 bool "Enable booting from both SDHCIs"
106 This option reflects that board has two SDHCI controllers which
107 platform can use as boot device. This option ensures that SPL will
108 setup BOOT_DEVICE_MMC2 for SDHCI1 controller and BOOT_DEVICE_MMC1 for
109 SDHCI0 controller. Platforms which have only one SDHCI controller
110 shouldn't enable this option because it for software SDHCI0 or SDHCI1
111 are both covered by BOOT_DEVICE_MMC1.
113 config SPL_ZYNQMP_ALT_BOOTMODE
115 default 0x0 if JTAG_MODE
116 default 0x1 if QSPI_MODE_24BIT
117 default 0x2 if QSPI_MODE_32BIT
118 default 0x3 if SD_MODE
119 default 0x4 if NAND_MODE
120 default 0x5 if SD_MODE1
121 default 0x6 if EMMC_MODE
122 default 0x7 if USB_MODE
123 default 0xa if SW_USBHOST_MODE
124 default 0xb if SW_SATA_MODE
125 default 0xe if SD1_LSHFT_MODE
129 depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
135 config QSPI_MODE_24BIT
136 bool "QSPI_MODE_24BIT"
138 config QSPI_MODE_32BIT
139 bool "QSPI_MODE_32BIT"
156 config SW_USBHOST_MODE
157 bool "SW USBHOST_MODE"
162 config SD1_LSHFT_MODE
163 bool "SD1_LSHFT_MODE"