6 config ARCH_UNIPHIER_32BIT
10 config ARCH_UNIPHIER_64BIT
13 select SPL_SEPARATE_BSS
14 select ARMV8_MULTIENTRY
15 select ARMV8_SPIN_TABLE
18 prompt "UniPhier SoC select"
19 default ARCH_UNIPHIER_PRO4
21 config ARCH_UNIPHIER_SLD3
22 bool "UniPhier PH1-sLD3 SoC"
23 select ARCH_UNIPHIER_32BIT
25 config ARCH_UNIPHIER_LD4_SLD8
26 bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
27 select ARCH_UNIPHIER_32BIT
29 config ARCH_UNIPHIER_PRO4
30 bool "UniPhier PH1-Pro4 SoC"
31 select ARCH_UNIPHIER_32BIT
33 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
34 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
35 select ARCH_UNIPHIER_32BIT
37 config ARCH_UNIPHIER_LD11
38 bool "UniPhier PH1-LD11 SoC"
39 select ARCH_UNIPHIER_64BIT
41 config ARCH_UNIPHIER_LD20
42 bool "UniPhier PH1-LD20 SoC"
43 select ARCH_UNIPHIER_64BIT
48 config ARCH_UNIPHIER_LD4
49 bool "Enable UniPhier PH1-LD4 SoC support"
50 depends on ARCH_UNIPHIER_LD4_SLD8
53 config ARCH_UNIPHIER_SLD8
54 bool "Enable UniPhier PH1-sLD8 SoC support"
55 depends on ARCH_UNIPHIER_LD4_SLD8
58 config ARCH_UNIPHIER_PRO5
59 bool "Enable UniPhier PH1-Pro5 SoC support"
60 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
63 config ARCH_UNIPHIER_PXS2
64 bool "Enable UniPhier ProXstream2 SoC support"
65 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
68 config ARCH_UNIPHIER_LD6B
69 bool "Enable UniPhier PH1-LD6b SoC support"
70 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
74 bool "Enable the UniPhier L2 cache controller"
75 depends on ARCH_UNIPHIER_32BIT
78 This option allows to use the UniPhier System Cache as L2 cache.
80 config MICRO_SUPPORT_CARD
81 bool "Use Micro Support Card"
83 This option provides support for the expansion board, available
84 on some UniPhier reference boards.
86 Say Y to use the on-board UART, Ether, LED devices.
89 bool "Enable boot mode pins monitor command"
92 The command "pinmon" shows the state of the boot mode pins.
93 The boot mode pins are latched when the system reset is deasserted
94 and determine which device the system should load a boot image from.
96 config CMD_DDRPHY_DUMP
97 bool "Enable dump command of DDR PHY parameters"
98 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
101 The command "ddrphy" shows the resulting parameters of DDR PHY
102 training; it is useful for the evaluation of DDR PHY training.
104 config CMD_DDRMPHY_DUMP
105 bool "Enable dump command of DDR Multi PHY parameters"
106 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
109 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
110 training; it is useful for the evaluation of DDR Multi PHY training.