7 select SPL_DM_SEQ_ALIAS
8 select SPL_DRIVERS_MISC_SUPPORT
10 select SPL_GPIO_SUPPORT
11 select SPL_LIBCOMMON_SUPPORT
12 select SPL_LIBGENERIC_SUPPORT
14 select SPL_OF_TRANSLATE
18 select SPL_SERIAL_SUPPORT
21 select SPL_WATCHDOG_SUPPORT if WATCHDOG
22 imply BOOTSTAGE_STASH if SPL_BOOTSTAGE
23 imply SPL_BOOTSTAGE if BOOTSTAGE
24 imply SPL_DISPLAY_PRINT
25 imply SPL_LIBDISK_SUPPORT
37 bool "Support STMicroelectronics STM32MP15x Soc"
38 select ARCH_SUPPORT_PSCI if !TFABOOT
39 select ARM_SMCCC if TFABOOT
41 select CPU_V7_HAS_NONSEC if !TFABOOT
42 select CPU_V7_HAS_VIRT
49 imply SYSRESET_PSCI if TFABOOT
50 imply SYSRESET_SYSCON if !TFABOOT
52 support of STMicroelectronics SOC STM32MP15x family
53 STM32MP157, STM32MP153 or STM32MP151
54 STMicroelectronics MPU with core ARMv7
55 dual core A7 for STM32MP157/3, monocore for STM32MP151
56 target all the STMicroelectronics board with SOC STM32MP1 family
59 prompt "STM32MP15x board select"
62 config TARGET_ST_STM32MP15x
63 bool "STMicroelectronics STM32MP15x boards"
69 imply CMD_CLS if CMD_BMP
71 imply PRE_CONSOLE_BUFFER
74 target the STMicroelectronics board with SOC STM32MP15x
75 managed by board/st/stm32mp1:
76 Evalulation board (EV1) or Discovery board (DK1 and DK2).
77 The difference between board are managed with devicetree
79 config TARGET_DH_STM32MP1_PDK2
80 bool "DH STM32MP1 PDK2"
85 Target the DH PDK2 development kit with STM32MP15x SoM.
90 bool "Support trusted boot with TF-A and OP-TEE"
94 Say Y here to enable boot with TF-A and OP-TEE
95 Trusted boot chain is :
96 BootRom => TF-A.stm32 (clock & DDR) => OP-TEE => U-Boot.stm32
97 OP-TEE monitor provides ST SMC to access to secure resources
105 config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2
106 hex "Partition on MMC2 to use to load U-Boot from"
107 depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
110 Partition on the second MMC to load U-Boot from when the MMC is being
114 bool "STM32 Extended TrustZone Protection"
115 depends on STM32MP15x
118 Say y to enable STM32 Extended TrustZone Protection
121 bool "command stm32key to fuse public key hash"
125 fuse public key hash in corresponding fuse used to authenticate
129 config PRE_CON_BUF_ADDR
132 config PRE_CON_BUF_SZ
135 config BOOTSTAGE_STASH_ADDR
139 config SYS_BOOTCOUNT_SINGLEWORD
142 # TAMP_BOOTCOUNT = TAMP_BACKUP_REGISTER(21)
143 config SYS_BOOTCOUNT_ADDR
149 config DEBUG_UART_BOARD_INIT
152 # debug on UART4 by default
153 config DEBUG_UART_BASE
156 # clock source is HSI on reset
157 config DEBUG_UART_CLOCK
161 source "board/st/stm32mp1/Kconfig"
162 source "board/dhelectronics/dh_stm32mp1/Kconfig"