7 select SPL_DM_SEQ_ALIAS
8 select SPL_DRIVERS_MISC_SUPPORT
10 select SPL_GPIO_SUPPORT
11 select SPL_LIBCOMMON_SUPPORT
12 select SPL_LIBGENERIC_SUPPORT
14 select SPL_OF_TRANSLATE
18 select SPL_SERIAL_SUPPORT
20 select SPL_WATCHDOG_SUPPORT
21 imply BOOTSTAGE_STASH if SPL_BOOTSTAGE
22 imply SPL_BOOTSTAGE if BOOTSTAGE
23 imply SPL_DISPLAY_PRINT
24 imply SPL_LIBDISK_SUPPORT
35 config TARGET_STM32MP1
36 bool "Support stm32mp1xx"
37 select ARCH_SUPPORT_PSCI if !STM32MP1_TRUSTED
39 select CPU_V7_HAS_NONSEC if !STM32MP1_TRUSTED
40 select CPU_V7_HAS_VIRT
50 imply PRE_CONSOLE_BUFFER
52 imply SYSRESET_PSCI if STM32MP1_TRUSTED
53 imply SYSRESET_SYSCON if !STM32MP1_TRUSTED
55 target STMicroelectronics SOC STM32MP1 family
56 STM32MP157, STM32MP153 or STM32MP151
57 STMicroelectronics MPU with core ARMv7
58 dual core A7 for STM32MP157/3, monocore for STM32MP151
60 config STM32MP1_TRUSTED
61 bool "Support trusted boot with TF-A"
65 Say Y here to enable boot with TF-A
66 Trusted boot chain is :
67 BootRom => TF-A.stm32 (clock & DDR) => U-Boot.stm32
68 TF-A monitor provides proprietary SMC to manage secure devices
71 bool "Support trusted boot with TF-A and OP-TEE"
72 depends on STM32MP1_TRUSTED
75 Say Y here to enable boot with TF-A and OP-TEE
76 Trusted boot chain is :
77 BootRom => TF-A.stm32 (clock & DDR) => OP-TEE => U-Boot.stm32
78 OP-TEE monitor provides ST SMC to access to secure resources
81 prompt "U-Boot base address"
84 configure the U-Boot base address
85 when DDR driver is used:
86 DDR + 1MB (0xC0100000)
91 config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2
92 hex "Partition on MMC2 to use to load U-Boot from"
93 depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
96 Partition on the second MMC to load U-Boot from when the MMC is being
100 bool "STM32 Extended TrustZone Protection"
101 depends on TARGET_STM32MP1
104 Say y to enable STM32 Extended TrustZone Protection
107 bool "command stm32key to fuse public key hash"
111 fuse public key hash in corresponding fuse used to authenticate
115 config PRE_CON_BUF_ADDR
118 config PRE_CON_BUF_SZ
121 config BOOTSTAGE_STASH_ADDR
125 config SYS_BOOTCOUNT_SINGLEWORD
128 # TAMP_BOOTCOUNT = TAMP_BACKUP_REGISTER(21)
129 config SYS_BOOTCOUNT_ADDR
135 config DEBUG_UART_BOARD_INIT
138 # debug on UART4 by default
139 config DEBUG_UART_BASE
142 # clock source is HSI on reset
143 config DEBUG_UART_CLOCK
147 source "board/st/stm32mp1/Kconfig"