2 * Copyright (C) 2014-2016 Stefan Roese <sr@denx.de>
4 * SPDX-License-Identifier: GPL-2.0+
9 #include <debug_uart.h>
13 #include <asm/arch/cpu.h>
14 #include <asm/arch/soc.h>
16 static u32 get_boot_device(void)
22 * First check, if UART boot-mode is active. This can only
23 * be done, via the bootrom error register. Here the
24 * MSB marks if the UART mode is active.
26 val = readl(CONFIG_BOOTROM_ERR_REG);
27 boot_device = (val & BOOTROM_ERR_MODE_MASK) >> BOOTROM_ERR_MODE_OFFS;
28 debug("BOOTROM_REG=0x%08x boot_device=0x%x\n", val, boot_device);
29 #if defined(CONFIG_ARMADA_38X)
31 * If the bootrom error register contains any else than zeros
32 * in the first 8 bits it's an error condition. And in that case
33 * try to boot from UART.
37 if (boot_device == BOOTROM_ERR_MODE_UART)
39 return BOOT_DEVICE_UART;
42 * Now check the SAR register for the strapped boot-device
44 val = readl(CONFIG_SAR_REG); /* SAR - Sample At Reset */
45 boot_device = (val & BOOT_DEV_SEL_MASK) >> BOOT_DEV_SEL_OFFS;
46 debug("SAR_REG=0x%08x boot_device=0x%x\n", val, boot_device);
47 switch (boot_device) {
48 #if defined(CONFIG_ARMADA_38X)
50 return BOOT_DEVICE_NAND;
52 #ifdef CONFIG_SPL_MMC_SUPPORT
54 case BOOT_FROM_MMC_ALT:
55 return BOOT_DEVICE_MMC1;
58 #ifdef BOOT_FROM_UART_ALT
59 case BOOT_FROM_UART_ALT:
61 return BOOT_DEVICE_UART;
64 return BOOT_DEVICE_SPI;
68 u32 spl_boot_device(void)
70 return get_boot_device();
73 void board_init_f(ulong dummy)
78 * Pin muxing needs to be done before UART output, since
79 * on A38x the UART pins need some re-muxing for output
84 /* Example code showing how to enable the debug UART on MVEBU */
87 * Debug UART can be used from here if required:
92 * printascii("string");
98 debug("spl_init() failed: %d\n", ret);
102 /* Use special translation offset for SPL */
103 dm_set_translation_offset(0xd0000000 - 0xf1000000);
105 preloader_console_init();
109 /* Armada 375 does not support SerDes and DDR3 init yet */
110 #if !defined(CONFIG_ARMADA_375)
111 /* First init the serdes PHY's */
119 * Return to the BootROM to continue the Marvell xmodem
120 * UART boot protocol. As initiated by the kwboot tool.
122 * This can only be done by the BootROM and not by the
123 * U-Boot SPL infrastructure, since the beginning of the
124 * image is already read and interpreted by the BootROM.
125 * SPL has no chance to receive this information. So we
126 * need to return to the BootROM to enable this xmodem
129 * If booting from NAND lets let the BootROM load the
130 * rest of the bootloader.
132 switch (get_boot_device()) {
133 case BOOT_DEVICE_UART:
134 #if defined(CONFIG_ARMADA_38X)
135 case BOOT_DEVICE_NAND: