1 #include <dt-bindings/input/input.h>
2 #include "tegra124.dtsi"
6 rtc0 = "/i2c@7000d000/pmic@40";
7 rtc1 = "/rtc@7000e000";
12 reg = <0x80000000 0x80000000>;
19 vdd-supply = <&vdd_3v3_hdmi>;
20 pll-supply = <&vdd_hdmi_pll>;
21 hdmi-supply = <&vdd_5v0_hdmi>;
23 nvidia,ddc-i2c-bus = <&hdmi_ddc>;
25 <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
31 nvidia,dpaux = <&dpaux>;
32 nvidia,panel = <&panel>;
36 vdd-supply = <&vdd_3v3_panel>;
42 /* Debug connector on the bottom of the board near SD card. */
52 clock-frequency = <100000>;
54 acodec: audio-codec@10 {
55 compatible = "maxim,max98090";
57 interrupt-parent = <&gpio>;
58 interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
61 temperature-sensor@4c {
62 compatible = "ti,tmp451";
64 interrupt-parent = <&gpio>;
65 interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
67 #thermal-sensor-cells = <1>;
73 clock-frequency = <100000>;
76 compatible = "elan,ekth3000";
78 interrupt-parent = <&gpio>;
79 interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
86 clock-frequency = <400000>;
89 compatible = "infineon,slb9645tt";
94 hdmi_ddc: i2c@7000c700 {
96 clock-frequency = <100000>;
101 clock-frequency = <400000>;
104 compatible = "ams,as3722";
106 interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
108 ams,system-power-controller;
110 #interrupt-cells = <2>;
111 interrupt-controller;
116 pinctrl-names = "default";
117 pinctrl-0 = <&as3722_default>;
119 as3722_default: pinmux {
133 pins = "gpio2", "gpio4", "gpio7";
139 pins = "gpio3", "gpio6";
145 function = "clk32k-out";
151 vsup-sd2-supply = <&vdd_5v0_sys>;
152 vsup-sd3-supply = <&vdd_5v0_sys>;
153 vsup-sd4-supply = <&vdd_5v0_sys>;
154 vsup-sd5-supply = <&vdd_5v0_sys>;
155 vin-ldo0-supply = <&vdd_1v35_lp0>;
156 vin-ldo1-6-supply = <&vdd_3v3_run>;
157 vin-ldo2-5-7-supply = <&vddio_1v8>;
158 vin-ldo3-4-supply = <&vdd_3v3_sys>;
159 vin-ldo9-10-supply = <&vdd_5v0_sys>;
160 vin-ldo11-supply = <&vdd_3v3_run>;
163 regulator-name = "+VDD_CPU_AP";
164 regulator-min-microvolt = <700000>;
165 regulator-max-microvolt = <1350000>;
166 regulator-min-microamp = <3500000>;
167 regulator-max-microamp = <3500000>;
170 ams,ext-control = <2>;
174 regulator-name = "+VDD_CORE";
175 regulator-min-microvolt = <700000>;
176 regulator-max-microvolt = <1350000>;
177 regulator-min-microamp = <2500000>;
178 regulator-max-microamp = <4000000>;
181 ams,ext-control = <1>;
185 regulator-name = "+1.35V_LP0(sd2)";
186 regulator-min-microvolt = <1350000>;
187 regulator-max-microvolt = <1350000>;
193 regulator-name = "+1.35V_LP0(sd3)";
194 regulator-min-microvolt = <1350000>;
195 regulator-max-microvolt = <1350000>;
201 regulator-name = "+1.05V_RUN";
202 regulator-min-microvolt = <1050000>;
203 regulator-max-microvolt = <1050000>;
207 regulator-name = "+1.8V_VDDIO";
208 regulator-min-microvolt = <1800000>;
209 regulator-max-microvolt = <1800000>;
214 regulator-name = "+VDD_GPU_AP";
215 regulator-min-microvolt = <650000>;
216 regulator-max-microvolt = <1200000>;
217 regulator-min-microamp = <3500000>;
218 regulator-max-microamp = <3500000>;
224 regulator-name = "+1.05V_RUN_AVDD";
225 regulator-min-microvolt = <1050000>;
226 regulator-max-microvolt = <1050000>;
229 ams,ext-control = <1>;
233 regulator-name = "+1.8V_RUN_CAM";
234 regulator-min-microvolt = <1800000>;
235 regulator-max-microvolt = <1800000>;
239 regulator-name = "+1.2V_GEN_AVDD";
240 regulator-min-microvolt = <1200000>;
241 regulator-max-microvolt = <1200000>;
247 regulator-name = "+1.00V_LP0_VDD_RTC";
248 regulator-min-microvolt = <1000000>;
249 regulator-max-microvolt = <1000000>;
256 regulator-name = "+3.3V_RUN_CAM";
257 regulator-min-microvolt = <2800000>;
258 regulator-max-microvolt = <2800000>;
262 regulator-name = "+1.2V_RUN_CAM_FRONT";
263 regulator-min-microvolt = <1200000>;
264 regulator-max-microvolt = <1200000>;
268 regulator-name = "+VDDIO_SDMMC3";
269 regulator-min-microvolt = <1800000>;
270 regulator-max-microvolt = <3300000>;
274 regulator-name = "+1.05V_RUN_CAM_REAR";
275 regulator-min-microvolt = <1050000>;
276 regulator-max-microvolt = <1050000>;
280 regulator-name = "+2.8V_RUN_TOUCH";
281 regulator-min-microvolt = <2800000>;
282 regulator-max-microvolt = <2800000>;
286 regulator-name = "+2.8V_RUN_CAM_AF";
287 regulator-min-microvolt = <2800000>;
288 regulator-max-microvolt = <2800000>;
292 regulator-name = "+1.8V_RUN_VPP_FUSE";
293 regulator-min-microvolt = <1800000>;
294 regulator-max-microvolt = <1800000>;
304 compatible = "google,cros-ec-spi";
305 spi-max-frequency = <3000000>;
306 interrupt-parent = <&gpio>;
307 interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
310 google,cros-ec-spi-msg-delay = <2000>;
313 compatible = "google,cros-ec-i2c-tunnel";
314 #address-cells = <1>;
317 google,remote-bus = <0>;
320 compatible = "ti,bq24735";
322 interrupt-parent = <&gpio>;
323 interrupts = <TEGRA_GPIO(J, 0)
325 ti,ac-detect-gpios = <&gpio
330 battery: sbs-battery@b {
331 compatible = "sbs,sbs-battery";
333 sbs,i2c-retry-count = <2>;
334 sbs,poll-retry-count = <10>;
335 power-supplies = <&charger>;
343 spi-max-frequency = <25000000>;
346 compatible = "winbond,w25q32dw";
347 spi-max-frequency = <25000000>;
353 nvidia,invert-interrupt;
354 nvidia,suspend-mode = <0>;
355 nvidia,cpu-pwr-good-time = <500>;
356 nvidia,cpu-pwr-off-time = <300>;
357 nvidia,core-pwr-good-time = <641 3845>;
358 nvidia,core-pwr-off-time = <61036>;
359 nvidia,core-power-req-active-high;
360 nvidia,sys-clock-req-active-high;
367 sdhci0_pwrseq: sdhci0_pwrseq {
368 compatible = "mmc-pwrseq-simple";
370 reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
373 sdhci@700b0000 { /* WiFi/BT on this bus */
375 power-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
379 mmc-pwrseq = <&sdhci0_pwrseq>;
380 vmmc-supply = <&vdd_3v3_lp0>;
381 vqmmc-supply = <&vddio_1v8>;
382 keep-power-in-suspend;
385 sdhci@700b0400 { /* SD Card on this bus */
387 cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
388 power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
389 wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
392 vqmmc-supply = <&vddio_sdmmc3>;
395 sdhci@700b0600 { /* eMMC on this bus */
405 vdd-cpu-supply = <&vdd_cpu>;
406 nvidia,i2c-fs-rate = <400000>;
415 usb@7d000000 { /* Rear external USB port. */
418 nvidia,vbus-gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
423 vbus-supply = <&vdd_usb1_vbus>;
426 usb@7d004000 { /* Internal webcam. */
434 vbus-supply = <&vdd_run_cam>;
437 usb@7d008000 { /* Left external USB port. */
439 nvidia,vbus-gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
444 vbus-supply = <&vdd_usb3_vbus>;
447 backlight: backlight {
448 compatible = "pwm-backlight";
450 enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
451 power-supply = <&vdd_led>;
452 pwms = <&pwm 1 1000000>;
454 default-brightness-level = <224>;
457 8 9 10 11 12 13 14 15
458 16 17 18 19 20 21 22 23
459 24 25 26 27 28 29 30 31
460 32 33 34 35 36 37 38 39
461 40 41 42 43 44 45 46 47
462 48 49 50 51 52 53 54 55
463 56 57 58 59 60 61 62 63
464 64 65 66 67 68 69 70 71
465 72 73 74 75 76 77 78 79
466 80 81 82 83 84 85 86 87
467 88 89 90 91 92 93 94 95
468 96 97 98 99 100 101 102 103
469 104 105 106 107 108 109 110 111
470 112 113 114 115 116 117 118 119
471 120 121 122 123 124 125 126 127
472 128 129 130 131 132 133 134 135
473 136 137 138 139 140 141 142 143
474 144 145 146 147 148 149 150 151
475 152 153 154 155 156 157 158 159
476 160 161 162 163 164 165 166 167
477 168 169 170 171 172 173 174 175
478 176 177 178 179 180 181 182 183
479 184 185 186 187 188 189 190 191
480 192 193 194 195 196 197 198 199
481 200 201 202 203 204 205 206 207
482 208 209 210 211 212 213 214 215
483 216 217 218 219 220 221 222 223
484 224 225 226 227 228 229 230 231
485 232 233 234 235 236 237 238 239
486 240 241 242 243 244 245 246 247
487 248 249 250 251 252 253 254 255
492 compatible = "simple-bus";
493 #address-cells = <1>;
497 compatible = "fixed-clock";
500 clock-frequency = <32768>;
506 vdd-cpu-supply = <&vdd_cpu>;
512 vdd-cpu-supply = <&vdd_cpu>;
517 compatible = "gpio-keys";
521 gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
522 linux,input-type = <5>;
523 linux,code = <KEY_RESERVED>;
524 debounce-interval = <1>;
530 gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
531 linux,code = <KEY_POWER>;
532 debounce-interval = <30>;
538 compatible = "simple-bus";
539 #address-cells = <1>;
542 vdd_mux: regulator@0 {
543 compatible = "regulator-fixed";
545 regulator-name = "+VDD_MUX";
546 regulator-min-microvolt = <12000000>;
547 regulator-max-microvolt = <12000000>;
552 vdd_5v0_sys: regulator@1 {
553 compatible = "regulator-fixed";
555 regulator-name = "+5V_SYS";
556 regulator-min-microvolt = <5000000>;
557 regulator-max-microvolt = <5000000>;
560 vin-supply = <&vdd_mux>;
563 vdd_3v3_sys: regulator@2 {
564 compatible = "regulator-fixed";
566 regulator-name = "+3.3V_SYS";
567 regulator-min-microvolt = <3300000>;
568 regulator-max-microvolt = <3300000>;
571 vin-supply = <&vdd_mux>;
574 vdd_3v3_run: regulator@3 {
575 compatible = "regulator-fixed";
577 regulator-name = "+3.3V_RUN";
578 regulator-min-microvolt = <3300000>;
579 regulator-max-microvolt = <3300000>;
582 gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
584 vin-supply = <&vdd_3v3_sys>;
587 vdd_3v3_hdmi: regulator@4 {
588 compatible = "regulator-fixed";
590 regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
591 regulator-min-microvolt = <3300000>;
592 regulator-max-microvolt = <3300000>;
593 vin-supply = <&vdd_3v3_run>;
596 vdd_led: regulator@5 {
597 compatible = "regulator-fixed";
599 regulator-name = "+VDD_LED";
600 gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
602 vin-supply = <&vdd_mux>;
605 vdd_5v0_ts: regulator@6 {
606 compatible = "regulator-fixed";
608 regulator-name = "+5V_VDD_TS_SW";
609 regulator-min-microvolt = <5000000>;
610 regulator-max-microvolt = <5000000>;
612 gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
614 vin-supply = <&vdd_5v0_sys>;
617 vdd_usb1_vbus: regulator@7 {
618 compatible = "regulator-fixed";
620 regulator-name = "+5V_USB_HS";
621 regulator-min-microvolt = <5000000>;
622 regulator-max-microvolt = <5000000>;
623 gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
626 vin-supply = <&vdd_5v0_sys>;
629 vdd_usb3_vbus: regulator@8 {
630 compatible = "regulator-fixed";
632 regulator-name = "+5V_USB_SS";
633 regulator-min-microvolt = <5000000>;
634 regulator-max-microvolt = <5000000>;
635 gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
638 vin-supply = <&vdd_5v0_sys>;
641 vdd_3v3_panel: regulator@9 {
642 compatible = "regulator-fixed";
644 regulator-name = "+3.3V_PANEL";
645 regulator-min-microvolt = <3300000>;
646 regulator-max-microvolt = <3300000>;
647 gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
649 vin-supply = <&vdd_3v3_run>;
652 vdd_3v3_lp0: regulator@10 {
653 compatible = "regulator-fixed";
655 regulator-name = "+3.3V_LP0";
656 regulator-min-microvolt = <3300000>;
657 regulator-max-microvolt = <3300000>;
659 * TODO: find a way to wire this up with the USB EHCI
660 * controllers so that it can be enabled on demand.
663 gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
665 vin-supply = <&vdd_3v3_sys>;
668 vdd_hdmi_pll: regulator@11 {
669 compatible = "regulator-fixed";
671 regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
672 regulator-min-microvolt = <1050000>;
673 regulator-max-microvolt = <1050000>;
674 gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
675 vin-supply = <&vdd_1v05_run>;
678 vdd_5v0_hdmi: regulator@12 {
679 compatible = "regulator-fixed";
681 regulator-name = "+5V_HDMI_CON";
682 regulator-min-microvolt = <5000000>;
683 regulator-max-microvolt = <5000000>;
684 gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
686 vin-supply = <&vdd_5v0_sys>;
691 nvidia,audio-routing =
696 "Mic Jack", "MICBIAS",
701 nvidia,i2s-controller = <&tegra_i2s1>;
702 nvidia,audio-codec = <&acodec>;
704 clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
705 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
706 <&tegra_car TEGRA124_CLK_EXTERN1>;
707 clock-names = "pll_a", "pll_a_out0", "mclk";
709 nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
710 nvidia,mic-det-gpios =
711 <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
715 compatible = "gpio-restart";
716 gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
721 #include "cros-ec-keyboard.dtsi"