1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
3 * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
4 * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
8 #include "stm32mp157c-ed1.dts"
11 model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
12 compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
15 stdout-path = "serial0:115200n8";
20 ethernet0 = ðernet0;
23 panel_backlight: panel-backlight {
24 compatible = "gpio-backlight";
25 gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
32 pinctrl-names = "default";
33 pinctrl-0 = <&cec_pins_a>;
49 remote-endpoint = <<dc_ep0_out>;
56 remote-endpoint = <&dsi_panel_in>;
62 compatible = "raydium,rm68200";
64 reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
65 backlight = <&panel_backlight>;
69 dsi_panel_in: endpoint {
70 remote-endpoint = <&dsi_out>;
78 pinctrl-0 = <ðernet0_rgmii_pins_a>;
79 pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
80 pinctrl-names = "default", "sleep";
81 phy-mode = "rgmii-id";
88 compatible = "snps,dwmac-mdio";
89 phy0: ethernet-phy@0 {
96 pinctrl-names = "default", "sleep";
97 pinctrl-0 = <&fmc_pins_a>;
98 pinctrl-1 = <&fmc_sleep_pins_a>;
100 #address-cells = <1>;
106 #address-cells = <1>;
112 pinctrl-names = "default";
113 pinctrl-0 = <&i2c2_pins_a>;
114 i2c-scl-rising-time-ns = <185>;
115 i2c-scl-falling-time-ns = <20>;
119 compatible = "st,stmfx-0300";
121 interrupts = <8 IRQ_TYPE_EDGE_RISING>;
122 interrupt-parent = <&gpioi>;
123 vdd-supply = <&v3v3>;
125 stmfx_pinctrl: stmfx-pin-controller {
126 compatible = "st,stmfx-0300-pinctrl";
129 interrupt-controller;
130 #interrupt-cells = <2>;
131 gpio-ranges = <&stmfx_pinctrl 0 0 24>;
138 pinctrl-names = "default";
139 pinctrl-0 = <&i2c5_pins_a>;
140 i2c-scl-rising-time-ns = <185>;
141 i2c-scl-falling-time-ns = <20>;
149 #address-cells = <1>;
152 ltdc_ep0_out: endpoint@0 {
154 remote-endpoint = <&dsi_in>;
160 pinctrl-names = "default";
161 pinctrl-0 = <&m_can1_pins_a>;
166 pinctrl-names = "default";
167 pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
168 reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
169 #address-cells = <1>;
173 flash0: mx66l51235l@0 {
175 spi-rx-bus-width = <4>;
176 spi-max-frequency = <108000000>;
177 #address-cells = <1>;
181 flash1: mx66l51235l@1 {
183 spi-rx-bus-width = <4>;
184 spi-max-frequency = <108000000>;
185 #address-cells = <1>;
191 pinctrl-names = "default";
192 pinctrl-0 = <&spi1_pins_a>;
199 pinctrl-0 = <&pwm2_pins_a>;
200 pinctrl-names = "default";
211 pinctrl-0 = <&pwm8_pins_a>;
212 pinctrl-names = "default";
223 pinctrl-0 = <&pwm12_pins_a>;
224 pinctrl-names = "default";
233 phys = <&usbphyc_port0>;
235 vbus-supply = <&vbus_sw>;
240 pinctrl-names = "default";
241 pinctrl-0 = <&usbotg_hs_pins_a>;
242 dr_mode = "peripheral";
243 phys = <&usbphyc_port1 0>;
244 phy-names = "usb2-phy";