arch/arm/dts/r8a7790-lager.dts

   1 /*
   2  * Device Tree Source for the Lager board
   3  *
   4  * Copyright (C) 2013-2014 Renesas Solutions Corp.
   5  * Copyright (C) 2014 Cogent Embedded, Inc.
   6  * Copyright (C) 2015-2016 Renesas Electronics Corporation
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0
   9  */
  10
  11 /*
  12  * SSI-AK4643
  13  *
  14  * SW1: 1: AK4643
  15  *      2: CN22
  16  *      3: ADV7511
  17  *
  18  * This command is required when Playback/Capture
  19  *
  20  *      amixer set "LINEOUT Mixer DACL" on
  21  *      amixer set "DVC Out" 100%
  22  *      amixer set "DVC In" 100%
  23  *
  24  * You can use Mute
  25  *
  26  *      amixer set "DVC Out Mute" on
  27  *      amixer set "DVC In Mute" on
  28  *
  29  * You can use Volume Ramp
  30  *
  31  *      amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
  32  *      amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
  33  *      amixer set "DVC Out Ramp" on
  34  *      aplay xxx.wav &
  35  *      amixer set "DVC Out"  80%  // Volume Down
  36  *      amixer set "DVC Out" 100%  // Volume Up
  37  */
  38
  39 /dts-v1/;
  40 #include "r8a7790.dtsi"
  41 #include <dt-bindings/gpio/gpio.h>
  42 #include <dt-bindings/input/input.h>
  43
  44 / {
  45         model = "Lager";
  46         compatible = "renesas,lager", "renesas,r8a7790";
  47
  48         aliases {
  49                 serial0 = &scif0;
  50                 serial1 = &scifa1;
  51                 i2c8 = &gpioi2c1;
  52                 i2c10 = &i2cexio0;
  53                 i2c11 = &i2cexio1;
  54         };
  55
  56         chosen {
  57                 bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
  58                 stdout-path = "serial0:115200n8";
  59         };
  60
  61         memory@40000000 {
  62                 device_type = "memory";
  63                 reg = <0 0x40000000 0 0x40000000>;
  64         };
  65
  66         memory@140000000 {
  67                 device_type = "memory";
  68                 reg = <1 0x40000000 0 0xc0000000>;
  69         };
  70
  71         lbsc {
  72                 #address-cells = <1>;
  73                 #size-cells = <1>;
  74         };
  75
  76         keyboard {
  77                 compatible = "gpio-keys";
  78
  79                 one {
  80                         linux,code = <KEY_1>;
  81                         label = "SW2-1";
  82                         wakeup-source;
  83                         debounce-interval = <20>;
  84                         gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
  85                 };
  86                 two {
  87                         linux,code = <KEY_2>;
  88                         label = "SW2-2";
  89                         wakeup-source;
  90                         debounce-interval = <20>;
  91                         gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
  92                 };
  93                 three {
  94                         linux,code = <KEY_3>;
  95                         label = "SW2-3";
  96                         wakeup-source;
  97                         debounce-interval = <20>;
  98                         gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
  99                 };
 100                 four {
 101                         linux,code = <KEY_4>;
 102                         label = "SW2-4";
 103                         wakeup-source;
 104                         debounce-interval = <20>;
 105                         gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
 106                 };
 107         };
 108
 109         leds {
 110                 compatible = "gpio-leds";
 111                 led6 {
 112                         gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
 113                 };
 114                 led7 {
 115                         gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
 116                 };
 117                 led8 {
 118                         gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
 119                 };
 120         };
 121
 122         fixedregulator3v3: regulator-3v3 {
 123                 compatible = "regulator-fixed";
 124                 regulator-name = "fixed-3.3V";
 125                 regulator-min-microvolt = <3300000>;
 126                 regulator-max-microvolt = <3300000>;
 127                 regulator-boot-on;
 128                 regulator-always-on;
 129         };
 130
 131         vcc_sdhi0: regulator-vcc-sdhi0 {
 132                 compatible = "regulator-fixed";
 133
 134                 regulator-name = "SDHI0 Vcc";
 135                 regulator-min-microvolt = <3300000>;
 136                 regulator-max-microvolt = <3300000>;
 137
 138                 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
 139                 enable-active-high;
 140         };
 141
 142         vccq_sdhi0: regulator-vccq-sdhi0 {
 143                 compatible = "regulator-gpio";
 144
 145                 regulator-name = "SDHI0 VccQ";
 146                 regulator-min-microvolt = <1800000>;
 147                 regulator-max-microvolt = <3300000>;
 148
 149                 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
 150                 gpios-states = <1>;
 151                 states = <3300000 1
 152                           1800000 0>;
 153         };
 154
 155         vcc_sdhi2: regulator-vcc-sdhi2 {
 156                 compatible = "regulator-fixed";
 157
 158                 regulator-name = "SDHI2 Vcc";
 159                 regulator-min-microvolt = <3300000>;
 160                 regulator-max-microvolt = <3300000>;
 161
 162                 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
 163                 enable-active-high;
 164         };
 165
 166         vccq_sdhi2: regulator-vccq-sdhi2 {
 167                 compatible = "regulator-gpio";
 168
 169                 regulator-name = "SDHI2 VccQ";
 170                 regulator-min-microvolt = <1800000>;
 171                 regulator-max-microvolt = <3300000>;
 172
 173                 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
 174                 gpios-states = <1>;
 175                 states = <3300000 1
 176                           1800000 0>;
 177         };
 178
 179         audio_clock: audio_clock {
 180                 compatible = "fixed-clock";
 181                 #clock-cells = <0>;
 182                 clock-frequency = <11289600>;
 183         };
 184
 185         rsnd_ak4643: sound {
 186                 compatible = "simple-audio-card";
 187
 188                 simple-audio-card,format = "left_j";
 189                 simple-audio-card,bitclock-master = <&sndcodec>;
 190                 simple-audio-card,frame-master = <&sndcodec>;
 191
 192                 sndcpu: simple-audio-card,cpu {
 193                         sound-dai = <&rcar_sound>;
 194                 };
 195
 196                 sndcodec: simple-audio-card,codec {
 197                         sound-dai = <&ak4643>;
 198                         clocks = <&audio_clock>;
 199                 };
 200         };
 201
 202         vga-encoder {
 203                 compatible = "adi,adv7123";
 204
 205                 ports {
 206                         #address-cells = <1>;
 207                         #size-cells = <0>;
 208
 209                         port@0 {
 210                                 reg = <0>;
 211                                 adv7123_in: endpoint {
 212                                         remote-endpoint = <&du_out_rgb>;
 213                                 };
 214                         };
 215                         port@1 {
 216                                 reg = <1>;
 217                                 adv7123_out: endpoint {
 218                                         remote-endpoint = <&vga_in>;
 219                                 };
 220                         };
 221                 };
 222         };
 223
 224         vga {
 225                 compatible = "vga-connector";
 226
 227                 port {
 228                         vga_in: endpoint {
 229                                 remote-endpoint = <&adv7123_out>;
 230                         };
 231                 };
 232         };
 233
 234         hdmi-in {
 235                 compatible = "hdmi-connector";
 236                 type = "a";
 237
 238                 port {
 239                         hdmi_con_in: endpoint {
 240                                 remote-endpoint = <&adv7612_in>;
 241                         };
 242                 };
 243         };
 244
 245         hdmi-out {
 246                 compatible = "hdmi-connector";
 247                 type = "a";
 248
 249                 port {
 250                         hdmi_con_out: endpoint {
 251                                 remote-endpoint = <&adv7511_out>;
 252                         };
 253                 };
 254         };
 255
 256         x2_clk: x2-clock {
 257                 compatible = "fixed-clock";
 258                 #clock-cells = <0>;
 259                 clock-frequency = <148500000>;
 260         };
 261
 262         x13_clk: x13-clock {
 263                 compatible = "fixed-clock";
 264                 #clock-cells = <0>;
 265                 clock-frequency = <148500000>;
 266         };
 267
 268         gpioi2c1: i2c-8 {
 269                 #address-cells = <1>;
 270                 #size-cells = <0>;
 271                 compatible = "i2c-gpio";
 272                 status = "disabled";
 273                 gpios = <&gpio1 17 GPIO_ACTIVE_HIGH /* sda */
 274                          &gpio1 16 GPIO_ACTIVE_HIGH /* scl */
 275                         >;
 276                 i2c-gpio,delay-us = <5>;
 277         };
 278
 279         /*
 280          * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
 281          * We use the I2C demuxer, so the desired IP core can be selected at runtime
 282          * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
 283          * Note: For testing the I2C slave feature, it is convenient to connect this
 284          * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
 285          * instantiate the slave device at runtime according to the documentation.
 286          * You can then communicate with the slave via IIC3.
 287          *
 288          * IIC0/I2C0 does not appear to support fallback to GPIO.
 289          */
 290         i2cexio0: i2c-10 {
 291                 compatible = "i2c-demux-pinctrl";
 292                 i2c-parent = <&iic0>, <&i2c0>;
 293                 i2c-bus-name = "i2c-exio0";
 294                 #address-cells = <1>;
 295                 #size-cells = <0>;
 296         };
 297
 298         /*
 299          * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
 300          * This is similar to the arangement described for i2cexio0 (above)
 301          * with a fallback to GPIO also provided.
 302          */
 303         i2cexio1: i2c-11 {
 304                 compatible = "i2c-demux-pinctrl";
 305                 i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
 306                 i2c-bus-name = "i2c-exio1";
 307                 #address-cells = <1>;
 308                 #size-cells = <0>;
 309         };
 310 };
 311
 312 &du {
 313         pinctrl-0 = <&du_pins>;
 314         pinctrl-names = "default";
 315         status = "okay";
 316
 317         clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
 318                  <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
 319                  <&x13_clk>, <&x2_clk>;
 320         clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1",
 321                       "dclkin.0", "dclkin.1";
 322
 323         ports {
 324                 port@0 {
 325                         endpoint {
 326                                 remote-endpoint = <&adv7123_in>;
 327                         };
 328                 };
 329                 port@1 {
 330                         endpoint {
 331                                 remote-endpoint = <&adv7511_in>;
 332                         };
 333                 };
 334                 port@2 {
 335                         lvds_connector: endpoint {
 336                         };
 337                 };
 338         };
 339 };
 340
 341 &extal_clk {
 342         clock-frequency = <20000000>;
 343 };
 344
 345 &pfc {
 346         pinctrl-0 = <&scif_clk_pins>;
 347         pinctrl-names = "default";
 348
 349         du_pins: du {
 350                 groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
 351                 function = "du";
 352         };
 353
 354         scif0_pins: scif0 {
 355                 groups = "scif0_data";
 356                 function = "scif0";
 357         };
 358
 359         scif_clk_pins: scif_clk {
 360                 groups = "scif_clk";
 361                 function = "scif_clk";
 362         };
 363
 364         ether_pins: ether {
 365                 groups = "eth_link", "eth_mdio", "eth_rmii";
 366                 function = "eth";
 367         };
 368
 369         phy1_pins: phy1 {
 370                 groups = "intc_irq0";
 371                 function = "intc";
 372         };
 373
 374         scifa1_pins: scifa1 {
 375                 groups = "scifa1_data";
 376                 function = "scifa1";
 377         };
 378
 379         sdhi0_pins: sd0 {
 380                 groups = "sdhi0_data4", "sdhi0_ctrl";
 381                 function = "sdhi0";
 382                 power-source = <3300>;
 383         };
 384
 385         sdhi0_pins_uhs: sd0_uhs {
 386                 groups = "sdhi0_data4", "sdhi0_ctrl";
 387                 function = "sdhi0";
 388                 power-source = <1800>;
 389         };
 390
 391         sdhi2_pins: sd2 {
 392                 groups = "sdhi2_data4", "sdhi2_ctrl";
 393                 function = "sdhi2";
 394                 power-source = <3300>;
 395         };
 396
 397         sdhi2_pins_uhs: sd2_uhs {
 398                 groups = "sdhi2_data4", "sdhi2_ctrl";
 399                 function = "sdhi2";
 400                 power-source = <1800>;
 401         };
 402
 403         mmc1_pins: mmc1 {
 404                 groups = "mmc1_data8", "mmc1_ctrl";
 405                 function = "mmc1";
 406         };
 407
 408         qspi_pins: qspi {
 409                 groups = "qspi_ctrl", "qspi_data4";
 410                 function = "qspi";
 411         };
 412
 413         msiof1_pins: msiof1 {
 414                 groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
 415                                  "msiof1_tx";
 416                 function = "msiof1";
 417         };
 418
 419         i2c0_pins: i2c0 {
 420                 groups = "i2c0";
 421                 function = "i2c0";
 422         };
 423
 424         iic0_pins: iic0 {
 425                 groups = "iic0";
 426                 function = "iic0";
 427         };
 428
 429         i2c1_pins: i2c1 {
 430                 groups = "i2c1";
 431                 function = "i2c1";
 432         };
 433
 434         iic1_pins: iic1 {
 435                 groups = "iic1";
 436                 function = "iic1";
 437         };
 438
 439         iic2_pins: iic2 {
 440                 groups = "iic2";
 441                 function = "iic2";
 442         };
 443
 444         iic3_pins: iic3 {
 445                 groups = "iic3";
 446                 function = "iic3";
 447         };
 448
 449         hsusb_pins: hsusb {
 450                 groups = "usb0_ovc_vbus";
 451                 function = "usb0";
 452         };
 453
 454         usb0_pins: usb0 {
 455                 groups = "usb0";
 456                 function = "usb0";
 457         };
 458
 459         usb1_pins: usb1 {
 460                 groups = "usb1";
 461                 function = "usb1";
 462         };
 463
 464         usb2_pins: usb2 {
 465                 groups = "usb2";
 466                 function = "usb2";
 467         };
 468
 469         vin0_pins: vin0 {
 470                 groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
 471                 function = "vin0";
 472         };
 473
 474         vin1_pins: vin1 {
 475                 groups = "vin1_data8", "vin1_clk";
 476                 function = "vin1";
 477         };
 478
 479         sound_pins: sound {
 480                 groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
 481                 function = "ssi";
 482         };
 483
 484         sound_clk_pins: sound_clk {
 485                 groups = "audio_clk_a";
 486                 function = "audio_clk";
 487         };
 488 };
 489
 490 &ether {
 491         pinctrl-0 = <&ether_pins &phy1_pins>;
 492         pinctrl-names = "default";
 493
 494         phy-handle = <&phy1>;
 495         renesas,ether-link-active-low;
 496         status = "okay";
 497
 498         phy1: ethernet-phy@1 {
 499                 reg = <1>;
 500                 interrupt-parent = <&irqc0>;
 501                 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 502                 micrel,led-mode = <1>;
 503         };
 504 };
 505
 506 &cmt0 {
 507         status = "okay";
 508 };
 509
 510 &mmcif1 {
 511         pinctrl-0 = <&mmc1_pins>;
 512         pinctrl-names = "default";
 513
 514         vmmc-supply = <&fixedregulator3v3>;
 515         bus-width = <8>;
 516         non-removable;
 517         status = "okay";
 518 };
 519
 520 &sata1 {
 521         status = "okay";
 522 };
 523
 524 &qspi {
 525         pinctrl-0 = <&qspi_pins>;
 526         pinctrl-names = "default";
 527
 528         status = "okay";
 529
 530         flash: flash@0 {
 531                 compatible = "spansion,s25fl512s", "jedec,spi-nor";
 532                 reg = <0>;
 533                 spi-max-frequency = <30000000>;
 534                 spi-tx-bus-width = <4>;
 535                 spi-rx-bus-width = <4>;
 536                 spi-cpha;
 537                 spi-cpol;
 538                 m25p,fast-read;
 539
 540                 partitions {
 541                         compatible = "fixed-partitions";
 542                         #address-cells = <1>;
 543                         #size-cells = <1>;
 544
 545                         partition@0 {
 546                                 label = "loader";
 547                                 reg = <0x00000000 0x00040000>;
 548                                 read-only;
 549                         };
 550                         partition@40000 {
 551                                 label = "user";
 552                                 reg = <0x00040000 0x00400000>;
 553                                 read-only;
 554                         };
 555                         partition@440000 {
 556                                 label = "flash";
 557                                 reg = <0x00440000 0x03bc0000>;
 558                         };
 559                 };
 560         };
 561 };
 562
 563 &scif0 {
 564         pinctrl-0 = <&scif0_pins>;
 565         pinctrl-names = "default";
 566
 567         status = "okay";
 568 };
 569
 570 &scifa1 {
 571         pinctrl-0 = <&scifa1_pins>;
 572         pinctrl-names = "default";
 573
 574         status = "okay";
 575 };
 576
 577 &scif_clk {
 578         clock-frequency = <14745600>;
 579 };
 580
 581 &msiof1 {
 582         pinctrl-0 = <&msiof1_pins>;
 583         pinctrl-names = "default";
 584
 585         status = "okay";
 586
 587         pmic: pmic@0 {
 588                 compatible = "renesas,r2a11302ft";
 589                 reg = <0>;
 590                 spi-max-frequency = <6000000>;
 591                 spi-cpol;
 592                 spi-cpha;
 593         };
 594 };
 595
 596 &sdhi0 {
 597         pinctrl-0 = <&sdhi0_pins>;
 598         pinctrl-1 = <&sdhi0_pins_uhs>;
 599         pinctrl-names = "default", "state_uhs";
 600
 601         vmmc-supply = <&vcc_sdhi0>;
 602         vqmmc-supply = <&vccq_sdhi0>;
 603         cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
 604         sd-uhs-sdr50;
 605         sd-uhs-sdr104;
 606         status = "okay";
 607 };
 608
 609 &sdhi2 {
 610         pinctrl-0 = <&sdhi2_pins>;
 611         pinctrl-1 = <&sdhi2_pins_uhs>;
 612         pinctrl-names = "default", "state_uhs";
 613
 614         vmmc-supply = <&vcc_sdhi2>;
 615         vqmmc-supply = <&vccq_sdhi2>;
 616         cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
 617         sd-uhs-sdr50;
 618         status = "okay";
 619 };
 620
 621 &cpu0 {
 622         cpu0-supply = <&vdd_dvfs>;
 623 };
 624
 625 &i2c0   {
 626         pinctrl-0 = <&i2c0_pins>;
 627         pinctrl-names = "i2c-exio0";
 628 };
 629
 630 &iic0   {
 631         pinctrl-0 = <&iic0_pins>;
 632         pinctrl-names = "i2c-exio0";
 633 };
 634
 635 &i2c1   {
 636         pinctrl-0 = <&i2c1_pins>;
 637         pinctrl-names = "i2c-exio1";
 638 };
 639
 640 &iic1   {
 641         pinctrl-0 = <&iic1_pins>;
 642         pinctrl-names = "i2c-exio1";
 643 };
 644
 645 &iic2   {
 646         status = "okay";
 647         pinctrl-0 = <&iic2_pins>;
 648         pinctrl-names = "default";
 649
 650         clock-frequency = <100000>;
 651
 652         ak4643: codec@12 {
 653                 compatible = "asahi-kasei,ak4643";
 654                 #sound-dai-cells = <0>;
 655                 reg = <0x12>;
 656         };
 657
 658         composite-in@20 {
 659                 compatible = "adi,adv7180";
 660                 reg = <0x20>;
 661                 remote = <&vin1>;
 662
 663                 port {
 664                         adv7180: endpoint {
 665                                 bus-width = <8>;
 666                                 remote-endpoint = <&vin1ep0>;
 667                         };
 668                 };
 669         };
 670
 671         hdmi@39 {
 672                 compatible = "adi,adv7511w";
 673                 reg = <0x39>;
 674                 interrupt-parent = <&gpio1>;
 675                 interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
 676
 677                 adi,input-depth = <8>;
 678                 adi,input-colorspace = "rgb";
 679                 adi,input-clock = "1x";
 680                 adi,input-style = <1>;
 681                 adi,input-justification = "evenly";
 682
 683                 ports {
 684                         #address-cells = <1>;
 685                         #size-cells = <0>;
 686
 687                         port@0 {
 688                                 reg = <0>;
 689                                 adv7511_in: endpoint {
 690                                         remote-endpoint = <&du_out_lvds0>;
 691                                 };
 692                         };
 693
 694                         port@1 {
 695                                 reg = <1>;
 696                                 adv7511_out: endpoint {
 697                                         remote-endpoint = <&hdmi_con_out>;
 698                                 };
 699                         };
 700                 };
 701         };
 702
 703         hdmi-in@4c {
 704                 compatible = "adi,adv7612";
 705                 reg = <0x4c>;
 706                 interrupt-parent = <&gpio1>;
 707                 interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 708                 default-input = <0>;
 709
 710                 ports {
 711                         #address-cells = <1>;
 712                         #size-cells = <0>;
 713
 714                         port@0 {
 715                                 reg = <0>;
 716                                 adv7612_in: endpoint {
 717                                         remote-endpoint = <&hdmi_con_in>;
 718                                 };
 719                         };
 720
 721                         port@2 {
 722                                 reg = <2>;
 723                                 adv7612_out: endpoint {
 724                                         remote-endpoint = <&vin0ep2>;
 725                                 };
 726                         };
 727                 };
 728         };
 729 };
 730
 731 &iic3 {
 732         pinctrl-names = "default";
 733         pinctrl-0 = <&iic3_pins>;
 734         status = "okay";
 735
 736         pmic@58 {
 737                 compatible = "dlg,da9063";
 738                 reg = <0x58>;
 739                 interrupt-parent = <&irqc0>;
 740                 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 741                 interrupt-controller;
 742
 743                 rtc {
 744                         compatible = "dlg,da9063-rtc";
 745                 };
 746
 747                 wdt {
 748                         compatible = "dlg,da9063-watchdog";
 749                 };
 750         };
 751
 752         vdd_dvfs: regulator@68 {
 753                 compatible = "dlg,da9210";
 754                 reg = <0x68>;
 755                 interrupt-parent = <&irqc0>;
 756                 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 757
 758                 regulator-min-microvolt = <1000000>;
 759                 regulator-max-microvolt = <1000000>;
 760                 regulator-boot-on;
 761                 regulator-always-on;
 762         };
 763 };
 764
 765 &pci0 {
 766         status = "okay";
 767         pinctrl-0 = <&usb0_pins>;
 768         pinctrl-names = "default";
 769 };
 770
 771 &pci1 {
 772         status = "okay";
 773         pinctrl-0 = <&usb1_pins>;
 774         pinctrl-names = "default";
 775 };
 776
 777 &xhci {
 778         status = "okay";
 779         pinctrl-0 = <&usb2_pins>;
 780         pinctrl-names = "default";
 781 };
 782
 783 &pci2 {
 784         status = "okay";
 785         pinctrl-0 = <&usb2_pins>;
 786         pinctrl-names = "default";
 787 };
 788
 789 &hsusb {
 790         status = "okay";
 791         pinctrl-0 = <&hsusb_pins>;
 792         pinctrl-names = "default";
 793         renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
 794 };
 795
 796 &usbphy {
 797         status = "okay";
 798 };
 799
 800 /* HDMI video input */
 801 &vin0 {
 802         pinctrl-0 = <&vin0_pins>;
 803         pinctrl-names = "default";
 804
 805         status = "okay";
 806
 807         port {
 808                 vin0ep2: endpoint {
 809                         remote-endpoint = <&adv7612_out>;
 810                         bus-width = <24>;
 811                         hsync-active = <0>;
 812                         vsync-active = <0>;
 813                         pclk-sample = <1>;
 814                         data-active = <1>;
 815                 };
 816         };
 817 };
 818
 819 /* composite video input */
 820 &vin1 {
 821         pinctrl-0 = <&vin1_pins>;
 822         pinctrl-names = "default";
 823
 824         status = "okay";
 825
 826         port {
 827                 #address-cells = <1>;
 828                 #size-cells = <0>;
 829
 830                 vin1ep0: endpoint {
 831                         remote-endpoint = <&adv7180>;
 832                         bus-width = <8>;
 833                 };
 834         };
 835 };
 836
 837 &rcar_sound {
 838         pinctrl-0 = <&sound_pins &sound_clk_pins>;
 839         pinctrl-names = "default";
 840
 841         /* Single DAI */
 842         #sound-dai-cells = <0>;
 843
 844         status = "okay";
 845
 846         rcar_sound,dai {
 847                 dai0 {
 848                         playback = <&ssi0 &src2 &dvc0>;
 849                         capture  = <&ssi1 &src3 &dvc1>;
 850                 };
 851         };
 852 };
 853
 854 &ssi1 {
 855         shared-pin;
 856 };