1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * Copyright (c) 2019 BayLibre, SAS
4 * Author: Neil Armstrong <narmstrong@baylibre.com>
9 #include "meson-g12b.dtsi"
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/gpio/meson-g12a-gpio.h>
12 #include <dt-bindings/sound/meson-g12a-tohdmitx.h>
15 compatible = "hardkernel,odroid-n2", "amlogic,g12b";
16 model = "Hardkernel ODROID-N2";
24 stdout-path = "serial0:115200n8";
28 device_type = "memory";
29 reg = <0x0 0x0 0x0 0x40000000>;
32 emmc_pwrseq: emmc-pwrseq {
33 compatible = "mmc-pwrseq-emmc";
34 reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
38 compatible = "gpio-leds";
42 gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
43 linux,default-trigger = "heartbeat";
47 tflash_vdd: regulator-tflash_vdd {
48 compatible = "regulator-fixed";
50 regulator-name = "TFLASH_VDD";
51 regulator-min-microvolt = <3300000>;
52 regulator-max-microvolt = <3300000>;
54 gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
58 tf_io: gpio-regulator-tf_io {
59 compatible = "regulator-gpio";
61 regulator-name = "TF_IO";
62 regulator-min-microvolt = <1800000>;
63 regulator-max-microvolt = <3300000>;
65 gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
72 flash_1v8: regulator-flash_1v8 {
73 compatible = "regulator-fixed";
74 regulator-name = "FLASH_1V8";
75 regulator-min-microvolt = <1800000>;
76 regulator-max-microvolt = <1800000>;
77 vin-supply = <&vcc_3v3>;
81 main_12v: regulator-main_12v {
82 compatible = "regulator-fixed";
83 regulator-name = "12V";
84 regulator-min-microvolt = <12000000>;
85 regulator-max-microvolt = <12000000>;
89 vcc_5v: regulator-vcc_5v {
90 compatible = "regulator-fixed";
91 regulator-name = "5V";
92 regulator-min-microvolt = <5000000>;
93 regulator-max-microvolt = <5000000>;
95 vin-supply = <&main_12v>;
98 vcc_1v8: regulator-vcc_1v8 {
99 compatible = "regulator-fixed";
100 regulator-name = "VCC_1V8";
101 regulator-min-microvolt = <1800000>;
102 regulator-max-microvolt = <1800000>;
103 vin-supply = <&vcc_3v3>;
107 vcc_3v3: regulator-vcc_3v3 {
108 compatible = "regulator-fixed";
109 regulator-name = "VCC_3V3";
110 regulator-min-microvolt = <3300000>;
111 regulator-max-microvolt = <3300000>;
112 vin-supply = <&vddao_3v3>;
114 /* FIXME: actually controlled by VDDCPU_B_EN */
117 hub_5v: regulator-hub_5v {
118 compatible = "regulator-fixed";
119 regulator-name = "HUB_5V";
120 regulator-min-microvolt = <5000000>;
121 regulator-max-microvolt = <5000000>;
122 vin-supply = <&vcc_5v>;
124 /* Connected to the Hub CHIPENABLE, LOW sets low power state */
125 gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
129 usb_pwr_en: regulator-usb_pwr_en {
130 compatible = "regulator-fixed";
131 regulator-name = "USB_PWR_EN";
132 regulator-min-microvolt = <5000000>;
133 regulator-max-microvolt = <5000000>;
134 vin-supply = <&vcc_5v>;
136 /* Connected to the microUSB port power enable */
137 gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
141 vddao_1v8: regulator-vddao_1v8 {
142 compatible = "regulator-fixed";
143 regulator-name = "VDDAO_1V8";
144 regulator-min-microvolt = <1800000>;
145 regulator-max-microvolt = <1800000>;
146 vin-supply = <&vddao_3v3>;
150 vddao_3v3: regulator-vddao_3v3 {
151 compatible = "regulator-fixed";
152 regulator-name = "VDDAO_3V3";
153 regulator-min-microvolt = <3300000>;
154 regulator-max-microvolt = <3300000>;
155 vin-supply = <&main_12v>;
160 compatible = "hdmi-connector";
164 hdmi_connector_in: endpoint {
165 remote-endpoint = <&hdmi_tx_tmds_out>;
171 compatible = "amlogic,axg-sound-card";
172 model = "G12A-ODROIDN2";
173 audio-aux-devs = <&tdmout_b>;
174 audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
175 "TDMOUT_B IN 1", "FRDDR_B OUT 1",
176 "TDMOUT_B IN 2", "FRDDR_C OUT 1",
177 "TDM_B Playback", "TDMOUT_B OUT";
179 assigned-clocks = <&clkc CLKID_MPLL2>,
182 assigned-clock-parents = <0>, <0>, <0>;
183 assigned-clock-rates = <294912000>,
189 sound-dai = <&frddr_a>;
193 sound-dai = <&frddr_b>;
197 sound-dai = <&frddr_c>;
200 /* 8ch hdmi interface */
202 sound-dai = <&tdmif_b>;
204 dai-tdm-slot-tx-mask-0 = <1 1>;
205 dai-tdm-slot-tx-mask-1 = <1 1>;
206 dai-tdm-slot-tx-mask-2 = <1 1>;
207 dai-tdm-slot-tx-mask-3 = <1 1>;
211 sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
217 sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
220 sound-dai = <&hdmi_tx>;
231 pinctrl-0 = <&cec_ao_a_h_pins>;
232 pinctrl-names = "default";
234 hdmi-phandle = <&hdmi_tx>;
238 pinctrl-0 = <&cec_ao_b_h_pins>;
239 pinctrl-names = "default";
241 hdmi-phandle = <&hdmi_tx>;
249 external_phy: ethernet-phy@0 {
250 /* Realtek RTL8211F (0x001cc916) */
254 reset-assert-us = <10000>;
255 reset-deassert-us = <30000>;
256 reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
258 interrupt-parent = <&gpio_intc>;
259 /* MAC_INTR on GPIOZ_14 */
260 interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
265 pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
266 pinctrl-names = "default";
269 phy-handle = <&external_phy>;
270 amlogic,tx-delay-ns = <2>;
287 * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
288 * to be turned high in order to be detected by the USB Controller
289 * This signal should be handled by a USB specific power sequence
290 * in order to reset the Hub when USB bus is powered down.
294 gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
296 line-name = "usb-hub-reset";
302 pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
303 pinctrl-names = "default";
304 hdmi-supply = <&vcc_5v>;
308 hdmi_tx_tmds_out: endpoint {
309 remote-endpoint = <&hdmi_connector_in>;
315 pinctrl-0 = <&remote_input_ao_pins>;
316 pinctrl-names = "default";
322 pinctrl-0 = <&sdcard_c_pins>;
323 pinctrl-1 = <&sdcard_clk_gate_c_pins>;
324 pinctrl-names = "default", "clk-gate";
328 max-frequency = <50000000>;
331 cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
332 vmmc-supply = <&tflash_vdd>;
333 vqmmc-supply = <&tf_io>;
340 pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
341 pinctrl-1 = <&emmc_clk_gate_pins>;
342 pinctrl-names = "default", "clk-gate";
348 max-frequency = <200000000>;
351 mmc-pwrseq = <&emmc_pwrseq>;
352 vmmc-supply = <&vcc_3v3>;
353 vqmmc-supply = <&flash_1v8>;
370 pinctrl-0 = <&uart_ao_a_pins>;
371 pinctrl-names = "default";
376 vbus-supply = <&usb_pwr_en>;
380 phy-supply = <&vcc_5v>;
384 /* Enable the hub which is connected to this port */
385 phy-supply = <&hub_5v>;