arch/arm/boot/dts/omap4-droid4-xt894.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /dts-v1/;
   3
   4 #include <dt-bindings/input/input.h>
   5 #include "omap443x.dtsi"
   6 #include "motorola-cpcap-mapphone.dtsi"
   7
   8 / {
   9         model = "Motorola Droid 4 XT894";
  10         compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
  11
  12         chosen {
  13                 stdout-path = &uart3;
  14         };
  15
  16         aliases {
  17                 display0 = &lcd0;
  18                 display1 = &hdmi0;
  19         };
  20
  21         /*
  22          * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
  23          * then 1023 - 1024 seems to contain mbm.
  24          */
  25         memory {
  26                 device_type = "memory";
  27                 reg = <0x80000000 0x3fd00000>;  /* 1021 MB */
  28         };
  29
  30         /* Poweroff GPIO probably connected to CPCAP */
  31         gpio-poweroff {
  32                 compatible = "gpio-poweroff";
  33                 pinctrl-0 = <&poweroff_gpio>;
  34                 pinctrl-names = "default";
  35                 gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;    /* gpio50 */
  36         };
  37
  38         hdmi0: connector {
  39                 compatible = "hdmi-connector";
  40                 pinctrl-0 = <&hdmi_hpd_gpio>;
  41                 pinctrl-names = "default";
  42                 label = "hdmi";
  43                 type = "d";
  44
  45                 hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;       /* gpio63 */
  46
  47                 port {
  48                         hdmi_connector_in: endpoint {
  49                                 remote-endpoint = <&hdmi_out>;
  50                         };
  51                 };
  52         };
  53
  54         /*
  55          * HDMI 5V regulator probably sourced from battery. Let's keep
  56          * keep this as always enabled for HDMI to work until we've
  57          * figured what the encoder chip is.
  58          */
  59         hdmi_regulator: regulator-hdmi {
  60                 compatible = "regulator-fixed";
  61                 regulator-name = "hdmi";
  62                 regulator-min-microvolt = <5000000>;
  63                 regulator-max-microvolt = <5000000>;
  64                 gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>;    /* gpio59 */
  65                 enable-active-high;
  66                 regulator-always-on;
  67         };
  68
  69         /* FS USB Host PHY on port 1 for mdm6600 */
  70         fsusb1_phy: usb-phy@1 {
  71                 compatible = "motorola,mapphone-mdm6600";
  72                 pinctrl-0 = <&usb_mdm6600_pins>;
  73                 pinctrl-names = "default";
  74                 enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
  75                 power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;     /* gpio_54 */
  76                 reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;     /* gpio_49 */
  77                 /* mode: gpio_148 gpio_149 */
  78                 motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
  79                                       <&gpio5 21 GPIO_ACTIVE_HIGH>;
  80                 /* cmd: gpio_103 gpio_104 gpio_142 */
  81                 motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
  82                                      <&gpio4 8 GPIO_ACTIVE_HIGH>,
  83                                      <&gpio5 14 GPIO_ACTIVE_HIGH>;
  84                 /* status: gpio_52 gpio_53 gpio_55 */
  85                 motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
  86                                         <&gpio2 21 GPIO_ACTIVE_HIGH>,
  87                                         <&gpio2 23 GPIO_ACTIVE_HIGH>;
  88                 #phy-cells = <0>;
  89         };
  90
  91         /* HS USB host TLL nop-phy on port 2 for w3glte */
  92         hsusb2_phy: usb-phy@2 {
  93                 compatible = "usb-nop-xceiv";
  94                 #phy-cells = <0>;
  95         };
  96
  97         /* LCD regulator from sw5 source */
  98         lcd_regulator: regulator-lcd {
  99                 compatible = "regulator-fixed";
 100                 regulator-name = "lcd";
 101                 regulator-min-microvolt = <5050000>;
 102                 regulator-max-microvolt = <5050000>;
 103                 gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;     /* gpio96 */
 104                 enable-active-high;
 105                 vin-supply = <&sw5>;
 106         };
 107
 108         /* This is probably coming straight from the battery.. */
 109         wl12xx_vmmc: regulator-wl12xx {
 110                 compatible = "regulator-fixed";
 111                 regulator-name = "vwl1271";
 112                 regulator-min-microvolt = <1650000>;
 113                 regulator-max-microvolt = <1650000>;
 114                 gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;    /* gpio94 */
 115                 startup-delay-us = <70000>;
 116                 enable-active-high;
 117         };
 118
 119         gpio_keys {
 120                 compatible = "gpio-keys";
 121
 122                 volume_down {
 123                         label = "Volume Down";
 124                         gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
 125                         linux,code = <KEY_VOLUMEDOWN>;
 126                         linux,can-disable;
 127                         /* Value above 7.95ms for no GPIO hardware debounce */
 128                         debounce-interval = <10>;
 129                 };
 130
 131                 slider {
 132                         label = "Keypad Slide";
 133                         gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
 134                         linux,input-type = <EV_SW>;
 135                         linux,code = <SW_KEYPAD_SLIDE>;
 136                         linux,can-disable;
 137                         /* Value above 7.95ms for no GPIO hardware debounce */
 138                         debounce-interval = <10>;
 139                 };
 140         };
 141
 142         soundcard {
 143                 compatible = "audio-graph-card";
 144                 label = "Droid 4 Audio";
 145
 146                 simple-graph-card,widgets =
 147                         "Speaker", "Earpiece",
 148                         "Speaker", "Loudspeaker",
 149                         "Headphone", "Headphone Jack",
 150                         "Microphone", "Internal Mic";
 151
 152                 simple-graph-card,routing =
 153                         "Earpiece", "EP",
 154                         "Loudspeaker", "SPKR",
 155                         "Headphone Jack", "HSL",
 156                         "Headphone Jack", "HSR",
 157                         "MICR", "Internal Mic";
 158
 159                 dais = <&mcbsp2_port>, <&mcbsp3_port>;
 160         };
 161
 162         pwm8: dmtimer-pwm-8 {
 163                 pinctrl-names = "default";
 164                 pinctrl-0 = <&vibrator_direction_pin>;
 165
 166                 compatible = "ti,omap-dmtimer-pwm";
 167                 #pwm-cells = <3>;
 168                 ti,timers = <&timer8>;
 169                 ti,clock-source = <0x01>;
 170         };
 171
 172         pwm9: dmtimer-pwm-9 {
 173                 pinctrl-names = "default";
 174                 pinctrl-0 = <&vibrator_enable_pin>;
 175
 176                 compatible = "ti,omap-dmtimer-pwm";
 177                 #pwm-cells = <3>;
 178                 ti,timers = <&timer9>;
 179                 ti,clock-source = <0x01>;
 180         };
 181
 182         vibrator {
 183                 compatible = "pwm-vibrator";
 184                 pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
 185                 pwm-names = "enable", "direction";
 186                 direction-duty-cycle-ns = <10000000>;
 187         };
 188 };
 189
 190 &dss {
 191         status = "okay";
 192 };
 193
 194 &dsi1 {
 195         status = "okay";
 196         vdd-supply = <&vcsi>;
 197
 198         port {
 199                 dsi1_out_ep: endpoint {
 200                         remote-endpoint = <&lcd0_in>;
 201                         lanes = <0 1 2 3 4 5>;
 202                 };
 203         };
 204
 205         lcd0: display {
 206                 compatible = "panel-dsi-cm";
 207                 label = "lcd0";
 208                 vddi-supply = <&lcd_regulator>;
 209                 reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;      /* gpio101 */
 210
 211                 width-mm = <50>;
 212                 height-mm = <89>;
 213
 214                 panel-timing {
 215                         clock-frequency = <0>;          /* Calculated by dsi */
 216
 217                         hback-porch = <2>;
 218                         hactive = <540>;
 219                         hfront-porch = <0>;
 220                         hsync-len = <2>;
 221
 222                         vback-porch = <1>;
 223                         vactive = <960>;
 224                         vfront-porch = <0>;
 225                         vsync-len = <1>;
 226
 227                         hsync-active = <0>;
 228                         vsync-active = <0>;
 229                         de-active = <1>;
 230                         pixelclk-active = <1>;
 231                 };
 232
 233                 port {
 234                         lcd0_in: endpoint {
 235                                 remote-endpoint = <&dsi1_out_ep>;
 236                         };
 237                 };
 238         };
 239 };
 240
 241 &hdmi {
 242         status = "okay";
 243         pinctrl-0 = <&dss_hdmi_pins>;
 244         pinctrl-names = "default";
 245         vdda-supply = <&vdac>;
 246
 247         port {
 248                 hdmi_out: endpoint {
 249                         remote-endpoint = <&hdmi_connector_in>;
 250                         lanes = <1 0 3 2 5 4 7 6>;
 251                 };
 252         };
 253 };
 254
 255 &i2c1 {
 256         tmp105@48 {
 257                 compatible = "ti,tmp105";
 258                 reg = <0x48>;
 259                 pinctrl-0 = <&tmp105_irq>;
 260                 pinctrl-names = "default";
 261                 /* kpd_row0.gpio_178 */
 262                 interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
 263                                        &omap4_pmx_core 0x14e>;
 264                 interrupt-names = "irq", "wakeup";
 265                 wakeup-source;
 266         };
 267 };
 268
 269 &keypad {
 270         keypad,num-rows = <8>;
 271         keypad,num-columns = <8>;
 272         linux,keymap = <
 273
 274         /* Row 1 */
 275         MATRIX_KEY(0, 2, KEY_1)
 276         MATRIX_KEY(0, 6, KEY_2)
 277         MATRIX_KEY(2, 3, KEY_3)
 278         MATRIX_KEY(0, 7, KEY_4)
 279         MATRIX_KEY(0, 4, KEY_5)
 280         MATRIX_KEY(5, 5, KEY_6)
 281         MATRIX_KEY(0, 1, KEY_7)
 282         MATRIX_KEY(0, 5, KEY_8)
 283         MATRIX_KEY(0, 0, KEY_9)
 284         MATRIX_KEY(1, 6, KEY_0)
 285
 286         /* Row 2 */
 287         MATRIX_KEY(3, 4, KEY_APOSTROPHE)
 288         MATRIX_KEY(7, 6, KEY_Q)
 289         MATRIX_KEY(7, 7, KEY_W)
 290         MATRIX_KEY(7, 2, KEY_E)
 291         MATRIX_KEY(1, 0, KEY_R)
 292         MATRIX_KEY(4, 4, KEY_T)
 293         MATRIX_KEY(1, 2, KEY_Y)
 294         MATRIX_KEY(6, 7, KEY_U)
 295         MATRIX_KEY(2, 2, KEY_I)
 296         MATRIX_KEY(5, 6, KEY_O)
 297         MATRIX_KEY(3, 7, KEY_P)
 298         MATRIX_KEY(6, 5, KEY_BACKSPACE)
 299
 300         /* Row 3 */
 301         MATRIX_KEY(5, 4, KEY_TAB)
 302         MATRIX_KEY(5, 7, KEY_A)
 303         MATRIX_KEY(2, 7, KEY_S)
 304         MATRIX_KEY(7, 0, KEY_D)
 305         MATRIX_KEY(2, 6, KEY_F)
 306         MATRIX_KEY(6, 2, KEY_G)
 307         MATRIX_KEY(6, 6, KEY_H)
 308         MATRIX_KEY(1, 4, KEY_J)
 309         MATRIX_KEY(3, 1, KEY_K)
 310         MATRIX_KEY(2, 1, KEY_L)
 311         MATRIX_KEY(4, 6, KEY_ENTER)
 312
 313         /* Row 4 */
 314         MATRIX_KEY(3, 6, KEY_LEFTSHIFT)         /* KEY_CAPSLOCK */
 315         MATRIX_KEY(6, 1, KEY_Z)
 316         MATRIX_KEY(7, 4, KEY_X)
 317         MATRIX_KEY(5, 1, KEY_C)
 318         MATRIX_KEY(1, 7, KEY_V)
 319         MATRIX_KEY(2, 4, KEY_B)
 320         MATRIX_KEY(4, 1, KEY_N)
 321         MATRIX_KEY(1, 1, KEY_M)
 322         MATRIX_KEY(3, 5, KEY_COMMA)
 323         MATRIX_KEY(5, 2, KEY_DOT)
 324         MATRIX_KEY(6, 3, KEY_UP)
 325         MATRIX_KEY(7, 3, KEY_OK)
 326
 327         /* Row 5 */
 328         MATRIX_KEY(2, 5, KEY_LEFTCTRL)          /* KEY_LEFTSHIFT */
 329         MATRIX_KEY(4, 5, KEY_LEFTALT)           /* SYM */
 330         MATRIX_KEY(6, 0, KEY_MINUS)
 331         MATRIX_KEY(4, 7, KEY_EQUAL)
 332         MATRIX_KEY(1, 5, KEY_SPACE)
 333         MATRIX_KEY(3, 2, KEY_SLASH)
 334         MATRIX_KEY(4, 3, KEY_LEFT)
 335         MATRIX_KEY(5, 3, KEY_DOWN)
 336         MATRIX_KEY(3, 3, KEY_RIGHT)
 337
 338         /* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
 339         MATRIX_KEY(5, 0, KEY_VOLUMEUP)
 340         >;
 341 };
 342
 343 &mmc1 {
 344         vmmc-supply = <&vwlan2>;
 345         bus-width = <4>;
 346         cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */
 347 };
 348
 349 &mmc2 {
 350         vmmc-supply = <&vsdio>;
 351         bus-width = <8>;
 352         ti,non-removable;
 353 };
 354
 355 &mmc3 {
 356         vmmc-supply = <&wl12xx_vmmc>;
 357         /* uart2_tx.sdmmc3_dat1 pad as wakeirq */
 358         interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
 359                                &omap4_pmx_core 0xde>;
 360         interrupt-names = "irq", "wakeup";
 361         non-removable;
 362         bus-width = <4>;
 363         cap-power-off-card;
 364         keep-power-in-suspend;
 365
 366         #address-cells = <1>;
 367         #size-cells = <0>;
 368         wlcore: wlcore@2 {
 369                 compatible = "ti,wl1285", "ti,wl1283";
 370                 reg = <2>;
 371                 /* gpio_100 with gpmc_wait2 pad as wakeirq */
 372                 interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
 373                                       <&omap4_pmx_core 0x4e>;
 374                 interrupt-names = "irq", "wakeup";
 375                 ref-clock-frequency = <26000000>;
 376                 tcxo-clock-frequency = <26000000>;
 377         };
 378 };
 379
 380 &i2c1 {
 381         led-controller@38 {
 382                 compatible = "ti,lm3532";
 383                 #address-cells = <1>;
 384                 #size-cells = <0>;
 385                 reg = <0x38>;
 386
 387                 enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
 388
 389                 ramp-up-us = <1024>;
 390                 ramp-down-us = <8193>;
 391
 392                 led@0 {
 393                         reg = <0>;
 394                         led-sources = <2>;
 395                         ti,led-mode = <0>;
 396                         label = ":backlight";
 397                         linux,default-trigger = "backlight";
 398                 };
 399
 400                 led@1 {
 401                         reg = <1>;
 402                         led-sources = <1>;
 403                         ti,led-mode = <0>;
 404                         label = ":kbd_backlight";
 405                 };
 406         };
 407 };
 408
 409 &i2c2 {
 410         touchscreen@4a {
 411                 compatible = "atmel,maxtouch";
 412                 reg = <0x4a>;
 413                 pinctrl-names = "default";
 414                 pinctrl-0 = <&touchscreen_pins>;
 415
 416                 reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */
 417
 418                 /* gpio_183 with sys_nirq2 pad as wakeup */
 419                 interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING>,
 420                                       <&omap4_pmx_core 0x160>;
 421                 interrupt-names = "irq", "wakeup";
 422                 wakeup-source;
 423         };
 424
 425         isl29030@44 {
 426                 compatible = "isil,isl29030";
 427                 reg = <0x44>;
 428
 429                 pinctrl-names = "default";
 430                 pinctrl-0 = <&als_proximity_pins>;
 431
 432                 interrupt-parent = <&gpio6>;
 433                 interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
 434         };
 435 };
 436
 437 &omap4_pmx_core {
 438
 439         /* hdmi_hpd.gpio_63 */
 440         hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
 441                 pinctrl-single,pins = <
 442                 OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
 443                 >;
 444         };
 445
 446         /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
 447         dss_hdmi_pins: pinmux_dss_hdmi_pins {
 448                 pinctrl-single,pins = <
 449                 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
 450                 OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
 451                 OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
 452                 >;
 453         };
 454
 455         /* gpmc_ncs0.gpio_50 */
 456         poweroff_gpio: pinmux_poweroff_pins {
 457                 pinctrl-single,pins = <
 458                 OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
 459                 >;
 460         };
 461
 462         /* kpd_row0.gpio_178 */
 463         tmp105_irq: pinmux_tmp105_irq {
 464                 pinctrl-single,pins = <
 465                 OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
 466                 >;
 467         };
 468
 469         usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
 470                 /* gpio_60 */
 471                 pinctrl-single,pins = <
 472                 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
 473                 >;
 474         };
 475
 476         touchscreen_pins: pinmux_touchscreen_pins {
 477                 pinctrl-single,pins = <
 478                 OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
 479                 OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
 480                 >;
 481         };
 482
 483         als_proximity_pins: pinmux_als_proximity_pins {
 484                 pinctrl-single,pins = <
 485                 OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
 486                 >;
 487         };
 488
 489         usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
 490                 pinctrl-single,pins = <
 491                 /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
 492                 OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
 493
 494                 /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
 495                 OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
 496
 497                 /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
 498                 OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
 499
 500                 /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
 501                 OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
 502
 503                 /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
 504                 OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
 505
 506                 /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
 507                 OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
 508
 509                 /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
 510                 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
 511
 512                 /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
 513                 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
 514
 515                 /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
 516                 OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
 517
 518                 /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
 519                 OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
 520
 521                 /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
 522                 OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
 523                 >;
 524         };
 525
 526         usb_ulpi_pins: pinmux_usb_ulpi_pins {
 527                 pinctrl-single,pins = <
 528                 OMAP4_IOPAD(0x196, MUX_MODE7)
 529                 OMAP4_IOPAD(0x198, MUX_MODE7)
 530                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
 531                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
 532                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
 533                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
 534                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
 535                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
 536                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
 537                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
 538                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
 539                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
 540                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
 541                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
 542                 >;
 543         };
 544
 545         /* usb0_otg_dp and usb0_otg_dm */
 546         usb_utmi_pins: pinmux_usb_utmi_pins {
 547                 pinctrl-single,pins = <
 548                 OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
 549                 OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
 550                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 551                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 552                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 553                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 554                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
 555                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
 556                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 557                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 558                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 559                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 560                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 561                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 562                 >;
 563         };
 564
 565         /*
 566          * Note that the v3.0.8 stock userspace dynamically remuxes uart1
 567          * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
 568          * when not used. If needed, we can add rts pin remux later based
 569          * on power measurements.
 570          */
 571         uart1_pins: pinmux_uart1_pins {
 572                 pinctrl-single,pins = <
 573                 /* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
 574                 OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
 575
 576                 /* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
 577                 OMAP4_IOPAD(0x13e, MUX_MODE1)
 578
 579                 /* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
 580                 OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
 581
 582                 /* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
 583                 OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
 584                 >;
 585         };
 586
 587         /* uart3_tx_irtx and uart3_rx_irrx */
 588         uart3_pins: pinmux_uart3_pins {
 589                 pinctrl-single,pins = <
 590                 OMAP4_IOPAD(0x196, MUX_MODE7)
 591                 OMAP4_IOPAD(0x198, MUX_MODE7)
 592                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 593                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 594                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 595                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 596                 OMAP4_IOPAD(0x1ba, MUX_MODE2)
 597                 OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
 598                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 599                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 600                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 601                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 602                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 603                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 604                 >;
 605         };
 606
 607         uart4_pins: pinmux_uart4_pins {
 608                 pinctrl-single,pins = <
 609                 OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)               /* uart4_rx */
 610                 OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)              /* uart4_tx */
 611                 OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5)        /* uart4_cts */
 612                 OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5)       /* uart4_rts */
 613                 >;
 614         };
 615
 616         mcbsp2_pins: pinmux_mcbsp2_pins {
 617                 pinctrl-single,pins = <
 618                 OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_clkx */
 619                 OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_dr */
 620                 OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)      /* abe_mcbsp2_dx */
 621                 OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_fsx */
 622                 >;
 623         };
 624
 625         mcbsp3_pins: pinmux_mcbsp3_pins {
 626                 pinctrl-single,pins = <
 627                 OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_dr */
 628                 OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1)      /* abe_mcbsp3_dx */
 629                 OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_clkx */
 630                 OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_fsx */
 631                 >;
 632         };
 633
 634         vibrator_direction_pin: pinmux_vibrator_direction_pin {
 635                 pinctrl-single,pins = <
 636                 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)      /* dmtimer8_pwm_evt (gpio_27) */
 637                 >;
 638         };
 639
 640         vibrator_enable_pin: pinmux_vibrator_enable_pin {
 641                 pinctrl-single,pins = <
 642                 OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)      /* dmtimer9_pwm_evt (gpio_28) */
 643                 >;
 644         };
 645 };
 646
 647 &omap4_pmx_wkup {
 648         usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
 649                 /* gpio_wk0 */
 650                 pinctrl-single,pins = <
 651                 OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
 652                 >;
 653         };
 654 };
 655
 656 /* Configure pwm clock source for timers 8 & 9 */
 657 &timer8 {
 658         assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
 659         assigned-clock-parents = <&sys_clkin_ck>;
 660 };
 661
 662 &timer9 {
 663         assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
 664         assigned-clock-parents = <&sys_clkin_ck>;
 665 };
 666
 667 /*
 668  * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
 669  * uart1 wakeirq.
 670  */
 671 &uart1 {
 672         pinctrl-names = "default";
 673         pinctrl-0 = <&uart1_pins>;
 674         interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
 675                                &omap4_pmx_core 0xfc>;
 676 };
 677
 678 &uart3 {
 679         interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
 680                                &omap4_pmx_core 0x17c>;
 681 };
 682
 683 &uart4 {
 684         pinctrl-names = "default";
 685         pinctrl-0 = <&uart4_pins>;
 686
 687         bluetooth {
 688                 compatible = "ti,wl1285-st";
 689                 enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
 690                 max-speed = <3686400>;
 691         };
 692 };
 693
 694 &usbhsohci {
 695         phys = <&fsusb1_phy>;
 696         phy-names = "usb";
 697 };
 698
 699 &usbhsehci {
 700         phys = <&hsusb2_phy>;
 701 };
 702
 703 &usbhshost {
 704         port1-mode = "ohci-phy-4pin-dpdm";
 705         port2-mode = "ehci-tll";
 706 };
 707
 708 /* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
 709 &usb_otg_hs {
 710         interface-type = <1>;
 711         mode = <3>;
 712         power = <50>;
 713 };
 714
 715 &i2c4 {
 716         ak8975: magnetometer@c {
 717                 compatible = "asahi-kasei,ak8975";
 718                 reg = <0x0c>;
 719
 720                 vdd-supply = <&vhvio>;
 721
 722                 interrupt-parent = <&gpio6>;
 723                 interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
 724
 725                 rotation-matrix = "-1", "0", "0",
 726                                   "0", "1", "0",
 727                                   "0", "0", "-1";
 728
 729         };
 730
 731         lis3dh: accelerometer@18 {
 732                 compatible = "st,lis3dh-accel";
 733                 reg = <0x18>;
 734
 735                 vdd-supply = <&vhvio>;
 736
 737                 interrupt-parent = <&gpio2>;
 738                 interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
 739
 740                 rotation-matrix = "0", "-1", "0",
 741                                   "1", "0", "0",
 742                                   "0", "0", "1";
 743         };
 744 };
 745
 746 &mcbsp2 {
 747         #sound-dai-cells = <0>;
 748         pinctrl-names = "default";
 749         pinctrl-0 = <&mcbsp2_pins>;
 750         status = "okay";
 751
 752         mcbsp2_port: port {
 753                 cpu_dai2: endpoint {
 754                         dai-format = "i2s";
 755                         remote-endpoint = <&cpcap_audio_codec0>;
 756                         frame-master = <&cpcap_audio_codec0>;
 757                         bitclock-master = <&cpcap_audio_codec0>;
 758                 };
 759         };
 760 };
 761
 762 &mcbsp3 {
 763         #sound-dai-cells = <0>;
 764         pinctrl-names = "default";
 765         pinctrl-0 = <&mcbsp3_pins>;
 766         status = "okay";
 767
 768         mcbsp3_port: port {
 769                 cpu_dai3: endpoint {
 770                         dai-format = "dsp_a";
 771                         frame-master = <&cpcap_audio_codec1>;
 772                         bitclock-master = <&cpcap_audio_codec1>;
 773                         remote-endpoint = <&cpcap_audio_codec1>;
 774                 };
 775         };
 776 };
 777
 778 &cpcap_audio_codec0 {
 779         remote-endpoint = <&cpu_dai2>;
 780 };
 781
 782 &cpcap_audio_codec1 {
 783         remote-endpoint = <&cpu_dai3>;
 784 };