2 # (C) Copyright 2000 - 2002
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC and ARM processors, which can be
29 installed in a boot ROM and used to initialize and test the hardware
30 or to download and run application code.
32 The development of U-Boot is closely related to Linux: some parts of
33 the source code originate in the Linux source tree, we have some
34 header files in common, and special provision has been made to
35 support booting of Linux images.
37 Some attention has been paid to make this software easily
38 configurable and extendable. For instance, all monitor commands are
39 implemented with the same call interface, so that it's very easy to
40 add new commands. Also, instead of permanently adding rarely used
41 code (for instance hardware test utilities) to the monitor, you can
42 load and run it dynamically.
48 In general, all boards for which a configuration option exists in the
49 Makefile have been tested to some extent and can be considered
50 "working". In fact, many of them are used in production systems.
52 In case of problems see the CHANGELOG and CREDITS files to find out
53 who contributed the specific port.
59 In case you have questions about, problems with or contributions for
60 U-Boot you should send a message to the U-Boot mailing list at
61 <u-boot-users@lists.sourceforge.net>. There is also an archive of
62 previous traffic on the mailing list - please search the archive
63 before asking FAQ's. Please see
64 http://lists.sourceforge.net/lists/listinfo/u-boot-users/
70 - start from 8xxrom sources
71 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
73 - make it easier to add custom boards
74 - make it possible to add other [PowerPC] CPUs
75 - extend functions, especially:
76 * Provide extended interface to Linux boot loader
79 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
80 - create ARMBoot project (http://sourceforge.net/projects/armboot)
81 - add other CPU families (starting with ARM)
82 - create U-Boot project (http://sourceforge.net/projects/u-boot)
88 The "official" name of this project is "Das U-Boot". The spelling
89 "U-Boot" shall be used in all written text (documentation, comments
90 in source files etc.). Example:
92 This is the README file for the U-Boot project.
94 File names etc. shall be based on the string "u-boot". Examples:
96 include/asm-ppc/u-boot.h
98 #include <asm/u-boot.h>
100 Variable names, preprocessor constants etc. shall be either based on
101 the string "u_boot" or on "U_BOOT". Example:
103 U_BOOT_VERSION u_boot_logo
104 IH_OS_U_BOOT u_boot_hush_start
110 U-Boot uses a 3 level version number containing a version, a
111 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
112 sub-version "34", and patchlevel "4".
114 The patchlevel is used to indicate certain stages of development
115 between released versions, i. e. officially released versions of
116 U-Boot will always have a patchlevel of "0".
122 - board Board dependent files
123 - common Misc architecture independent functions
124 - cpu CPU specific files
125 - disk Code for disk drive partition handling
126 - doc Documentation (don't expect too much)
127 - drivers Commonly used device drivers
128 - dtt Digital Thermometer and Thermostat drivers
129 - examples Example code for standalone applications, etc.
130 - include Header Files
131 - disk Harddisk interface code
132 - net Networking code
133 - ppc Files generic to PowerPC architecture
134 - post Power On Self Test
135 - post/arch Symlink to architecture specific Power On Self Test
136 - post/arch-ppc PowerPC architecture specific Power On Self Test
137 - post/cpu/mpc8260 MPC8260 CPU specific Power On Self Test
138 - post/cpu/mpc8xx MPC8xx CPU specific Power On Self Test
139 - rtc Real Time Clock drivers
140 - tools Tools to build S-Record or U-Boot images, etc.
142 - cpu/74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
143 - cpu/arm925t Files specific to ARM 925 CPUs
144 - cpu/arm926ejs Files specific to ARM 926 CPUs
145 - cpu/mpc5xx Files specific to Motorola MPC5xx CPUs
146 - cpu/mpc8xx Files specific to Motorola MPC8xx CPUs
147 - cpu/mpc824x Files specific to Motorola MPC824x CPUs
148 - cpu/mpc8260 Files specific to Motorola MPC8260 CPU
149 - cpu/mpc85xx Files specific to Motorola MPC85xx CPUs
150 - cpu/ppc4xx Files specific to IBM 4xx CPUs
153 - board/LEOX/ Files specific to boards manufactured by The LEOX team
154 - board/LEOX/elpt860 Files specific to ELPT860 boards
156 Files specific to RPXClassic boards
157 - board/RPXlite Files specific to RPXlite boards
158 - board/at91rm9200dk Files specific to AT91RM9200DK boards
159 - board/c2mon Files specific to c2mon boards
160 - board/cmi Files specific to cmi boards
161 - board/cogent Files specific to Cogent boards
162 (need further configuration)
163 Files specific to CPCIISER4 boards
164 - board/cpu86 Files specific to CPU86 boards
165 - board/cray/ Files specific to boards manufactured by Cray
166 - board/cray/L1 Files specific to L1 boards
167 - board/cu824 Files specific to CU824 boards
168 - board/ebony Files specific to IBM Ebony board
169 - board/eric Files specific to ERIC boards
170 - board/esd/ Files specific to boards manufactured by ESD
171 - board/esd/adciop Files specific to ADCIOP boards
172 - board/esd/ar405 Files specific to AR405 boards
173 - board/esd/canbt Files specific to CANBT boards
174 - board/esd/cpci405 Files specific to CPCI405 boards
175 - board/esd/cpciiser4 Files specific to CPCIISER4 boards
176 - board/esd/common Common files for ESD boards
177 - board/esd/dasa_sim Files specific to DASA_SIM boards
178 - board/esd/du405 Files specific to DU405 boards
179 - board/esd/ocrtc Files specific to OCRTC boards
180 - board/esd/pci405 Files specific to PCI405 boards
182 Files specific to ESTEEM192E boards
183 - board/etx094 Files specific to ETX_094 boards
185 Files specific to EVB64260 boards
186 - board/fads Files specific to FADS boards
187 - board/flagadm Files specific to FLAGADM boards
188 - board/gen860t Files specific to GEN860T and GEN860T_SC boards
189 - board/genietv Files specific to GENIETV boards
190 - board/gth Files specific to GTH boards
191 - board/hermes Files specific to HERMES boards
192 - board/hymod Files specific to HYMOD boards
193 - board/icu862 Files specific to ICU862 boards
194 - board/ip860 Files specific to IP860 boards
196 Files specific to Interphase4539 boards
197 - board/ivm Files specific to IVMS8/IVML24 boards
198 - board/lantec Files specific to LANTEC boards
199 - board/lwmon Files specific to LWMON boards
200 - board/mbx8xx Files specific to MBX boards
202 Files specific to MPC8260ADS and PQ2FADS-ZU boards
204 Files specific to MPC8540ADS boards
206 Files specific to MPC8560ADS boards
207 - board/mpl/ Files specific to boards manufactured by MPL
208 - board/mpl/common Common files for MPL boards
209 - board/mpl/pip405 Files specific to PIP405 boards
210 - board/mpl/mip405 Files specific to MIP405 boards
211 - board/mpl/vcma9 Files specific to VCMA9 boards
212 - board/musenki Files specific to MUSEKNI boards
213 - board/mvs1 Files specific to MVS1 boards
214 - board/nx823 Files specific to NX823 boards
215 - board/oxc Files specific to OXC boards
217 Files specific to OMAP 1510 Innovator boards
219 Files specific to OMAP 1610 Innovator boards
220 - board/pcippc2 Files specific to PCIPPC2/PCIPPC6 boards
221 - board/pm826 Files specific to PM826 boards
223 Files specific to PPMC8260 boards
225 Files specific to RPXsuper boards
227 Files specific to RSDproto boards
229 Files specific to Sandpoint boards
230 - board/sbc8260 Files specific to SBC8260 boards
231 - board/sacsng Files specific to SACSng boards
232 - board/siemens Files specific to boards manufactured by Siemens AG
233 - board/siemens/CCM Files specific to CCM boards
234 - board/siemens/IAD210 Files specific to IAD210 boards
235 - board/siemens/SCM Files specific to SCM boards
236 - board/siemens/pcu_e Files specific to PCU_E boards
237 - board/sixnet Files specific to SIXNET boards
238 - board/spd8xx Files specific to SPD8xxTS boards
239 - board/tqm8260 Files specific to TQM8260 boards
240 - board/tqm8xx Files specific to TQM8xxL boards
241 - board/w7o Files specific to W7O boards
243 Files specific to Walnut405 boards
244 - board/westel/ Files specific to boards manufactured by Westel Wireless
245 - board/westel/amx860 Files specific to AMX860 boards
246 - board/utx8245 Files specific to UTX8245 boards
247 - board/zpc1900 Files specific to Zephyr Engineering ZPC.1900 board
249 Software Configuration:
250 =======================
252 Configuration is usually done using C preprocessor defines; the
253 rationale behind that is to avoid dead code whenever possible.
255 There are two classes of configuration variables:
257 * Configuration _OPTIONS_:
258 These are selectable by the user and have names beginning with
261 * Configuration _SETTINGS_:
262 These depend on the hardware etc. and should not be meddled with if
263 you don't know what you're doing; they have names beginning with
266 Later we will add a configuration tool - probably similar to or even
267 identical to what's used for the Linux kernel. Right now, we have to
268 do the configuration by hand, which means creating some symbolic
269 links and editing some configuration files. We use the TQM8xxL boards
273 Selection of Processor Architecture and Board Type:
274 ---------------------------------------------------
276 For all supported boards there are ready-to-use default
277 configurations available; just type "make <board_name>_config".
279 Example: For a TQM823L module type:
284 For the Cogent platform, you need to specify the cpu type as well;
285 e.g. "make cogent_mpc8xx_config". And also configure the cogent
286 directory according to the instructions in cogent/README.
289 Configuration Options:
290 ----------------------
292 Configuration depends on the combination of board and CPU type; all
293 such information is kept in a configuration file
294 "include/configs/<board_name>.h".
296 Example: For a TQM823L module, all configuration settings are in
297 "include/configs/TQM823L.h".
300 Many of the options are named exactly as the corresponding Linux
301 kernel configuration options. The intention is to make it easier to
302 build a config tool - later.
305 The following options need to be configured:
307 - CPU Type: Define exactly one of
311 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
313 or CONFIG_MPC824X, CONFIG_MPC8260
329 - Board Type: Define exactly one of
331 PowerPC based boards:
332 ---------------------
334 CONFIG_ADCIOP, CONFIG_ICU862 CONFIG_RPXsuper,
335 CONFIG_ADS860, CONFIG_IP860, CONFIG_SM850,
336 CONFIG_AMX860, CONFIG_IPHASE4539, CONFIG_SPD823TS,
337 CONFIG_AR405, CONFIG_IVML24, CONFIG_SXNI855T,
338 CONFIG_BAB7xx, CONFIG_IVML24_128, CONFIG_Sandpoint8240,
339 CONFIG_CANBT, CONFIG_IVML24_256, CONFIG_Sandpoint8245,
340 CONFIG_CCM, CONFIG_IVMS8, CONFIG_TQM823L,
341 CONFIG_CPCI405, CONFIG_IVMS8_128, CONFIG_TQM850L,
342 CONFIG_CPCI4052, CONFIG_IVMS8_256, CONFIG_TQM855L,
343 CONFIG_CPCIISER4, CONFIG_LANTEC, CONFIG_TQM860L,
344 CONFIG_CPU86, CONFIG_MBX, CONFIG_TQM8260,
345 CONFIG_CRAYL1, CONFIG_MBX860T, CONFIG_TTTech,
346 CONFIG_CU824, CONFIG_MHPC, CONFIG_UTX8245,
347 CONFIG_DASA_SIM, CONFIG_MIP405, CONFIG_W7OLMC,
348 CONFIG_DU405, CONFIG_MOUSSE, CONFIG_W7OLMG,
349 CONFIG_ELPPC, CONFIG_MPC8260ADS, CONFIG_WALNUT405,
350 CONFIG_ERIC, CONFIG_MUSENKI, CONFIG_ZUMA,
351 CONFIG_ESTEEM192E, CONFIG_MVS1, CONFIG_c2mon,
352 CONFIG_ETX094, CONFIG_NX823, CONFIG_cogent_mpc8260,
353 CONFIG_EVB64260, CONFIG_OCRTC, CONFIG_cogent_mpc8xx,
354 CONFIG_FADS823, CONFIG_ORSG, CONFIG_ep8260,
355 CONFIG_FADS850SAR, CONFIG_OXC, CONFIG_gw8260,
356 CONFIG_FADS860T, CONFIG_PCI405, CONFIG_hermes,
357 CONFIG_FLAGADM, CONFIG_PCIPPC2, CONFIG_hymod,
358 CONFIG_FPS850L, CONFIG_PCIPPC6, CONFIG_lwmon,
359 CONFIG_GEN860T, CONFIG_PIP405, CONFIG_pcu_e,
360 CONFIG_GENIETV, CONFIG_PM826, CONFIG_ppmc8260,
361 CONFIG_GTH, CONFIG_RPXClassic, CONFIG_rsdproto,
362 CONFIG_IAD210, CONFIG_RPXlite, CONFIG_sbc8260,
363 CONFIG_EBONY, CONFIG_sacsng, CONFIG_FPS860L,
364 CONFIG_V37, CONFIG_ELPT860, CONFIG_CMI,
365 CONFIG_NETVIA, CONFIG_RBC823, CONFIG_ZPC1900,
366 CONFIG_MPC8540ADS, CONFIG_MPC8560ADS
371 CONFIG_HHP_CRADLE, CONFIG_DNP1110, CONFIG_EP7312,
372 CONFIG_IMPA7, CONFIG_LART, CONFIG_LUBBOCK,
373 CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610
374 CONFIG_SHANNON, CONFIG_SMDK2400, CONFIG_SMDK2410,
375 CONFIG_TRAB, CONFIG_VCMA9, CONFIG_AT91RM9200DK
378 - CPU Module Type: (if CONFIG_COGENT is defined)
379 Define exactly one of
381 --- FIXME --- not tested yet:
382 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
383 CONFIG_CMA287_23, CONFIG_CMA287_50
385 - Motherboard Type: (if CONFIG_COGENT is defined)
386 Define exactly one of
387 CONFIG_CMA101, CONFIG_CMA102
389 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
390 Define one or more of
393 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
394 Define one or more of
395 CONFIG_LCD_HEARTBEAT - update a character position on
396 the lcd display every second with
399 - Board flavour: (if CONFIG_MPC8260ADS is defined)
402 CFG_8260ADS - original MPC8260ADS
403 CFG_8266ADS - MPC8266ADS (untested)
404 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
407 - MPC824X Family Member (if CONFIG_MPC824X is defined)
408 Define exactly one of
409 CONFIG_MPC8240, CONFIG_MPC8245
411 - 8xx CPU Options: (if using an 8xx cpu)
412 Define one or more of
413 CONFIG_8xx_GCLK_FREQ - if get_gclk_freq() cannot work
414 e.g. if there is no 32KHz
415 reference PIT/RTC clock
417 - Linux Kernel Interface:
420 U-Boot stores all clock information in Hz
421 internally. For binary compatibility with older Linux
422 kernels (which expect the clocks passed in the
423 bd_info data to be in MHz) the environment variable
424 "clocks_in_mhz" can be defined so that U-Boot
425 converts clock data to MHZ before passing it to the
427 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
428 "clocks_in_mhz=1" is automatically included in the
431 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
433 When transfering memsize parameter to linux, some versions
434 expect it to be in bytes, others in MB.
435 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
438 Depending on board, define exactly one serial port
439 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
440 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
441 console by defining CONFIG_8xx_CONS_NONE
443 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
444 port routines must be defined elsewhere
445 (i.e. serial_init(), serial_getc(), ...)
448 Enables console device for a color framebuffer. Needs following
449 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
450 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
452 VIDEO_HW_RECTFILL graphic chip supports
455 VIDEO_HW_BITBLT graphic chip supports
456 bit-blit (cf. smiLynxEM)
457 VIDEO_VISIBLE_COLS visible pixel columns
459 VIDEO_VISIBLE_ROWS visible pixel rows
460 VIDEO_PIXEL_SIZE bytes per pixel
461 VIDEO_DATA_FORMAT graphic data format
462 (0-5, cf. cfb_console.c)
463 VIDEO_FB_ADRS framebuffer address
464 VIDEO_KBD_INIT_FCT keyboard int fct
465 (i.e. i8042_kbd_init())
466 VIDEO_TSTC_FCT test char fct
468 VIDEO_GETC_FCT get char fct
470 CONFIG_CONSOLE_CURSOR cursor drawing on/off
471 (requires blink timer
473 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
474 CONFIG_CONSOLE_TIME display time/date info in
476 (requires CFG_CMD_DATE)
477 CONFIG_VIDEO_LOGO display Linux logo in
479 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
480 linux_logo.h for logo.
481 Requires CONFIG_VIDEO_LOGO
482 CONFIG_CONSOLE_EXTRA_INFO
483 addional board info beside
486 When CONFIG_CFB_CONSOLE is defined, video console is
487 default i/o. Serial console can be forced with
488 environment 'console=serial'.
490 When CONFIG_SILENT_CONSOLE is defined, all console
491 messages (by U-Boot and Linux!) can be silenced with
492 the "silent" environment variable. See
493 doc/README.silent for more information.
496 CONFIG_BAUDRATE - in bps
497 Select one of the baudrates listed in
498 CFG_BAUDRATE_TABLE, see below.
500 - Interrupt driven serial port input:
501 CONFIG_SERIAL_SOFTWARE_FIFO
504 Use an interrupt handler for receiving data on the
505 serial port. It also enables using hardware handshake
506 (RTS/CTS) and UART's built-in FIFO. Set the number of
507 bytes the interrupt driven input buffer should have.
509 Set to 0 to disable this feature (this is the default).
510 This will also disable hardware handshake.
512 - Console UART Number:
516 If defined internal UART1 (and not UART0) is used
517 as default U-Boot console.
519 - Boot Delay: CONFIG_BOOTDELAY - in seconds
520 Delay before automatically booting the default image;
521 set to -1 to disable autoboot.
523 See doc/README.autoboot for these options that
524 work with CONFIG_BOOTDELAY. None are required.
525 CONFIG_BOOT_RETRY_TIME
526 CONFIG_BOOT_RETRY_MIN
527 CONFIG_AUTOBOOT_KEYED
528 CONFIG_AUTOBOOT_PROMPT
529 CONFIG_AUTOBOOT_DELAY_STR
530 CONFIG_AUTOBOOT_STOP_STR
531 CONFIG_AUTOBOOT_DELAY_STR2
532 CONFIG_AUTOBOOT_STOP_STR2
533 CONFIG_ZERO_BOOTDELAY_CHECK
534 CONFIG_RESET_TO_RETRY
538 Only needed when CONFIG_BOOTDELAY is enabled;
539 define a command string that is automatically executed
540 when no character is read on the console interface
541 within "Boot Delay" after reset.
544 This can be used to pass arguments to the bootm
545 command. The value of CONFIG_BOOTARGS goes into the
546 environment value "bootargs".
548 CONFIG_RAMBOOT and CONFIG_NFSBOOT
549 The value of these goes into the environment as
550 "ramboot" and "nfsboot" respectively, and can be used
551 as a convenience, when switching between booting from
557 When this option is #defined, the existence of the
558 environment variable "preboot" will be checked
559 immediately before starting the CONFIG_BOOTDELAY
560 countdown and/or running the auto-boot command resp.
561 entering interactive mode.
563 This feature is especially useful when "preboot" is
564 automatically generated or modified. For an example
565 see the LWMON board specific code: here "preboot" is
566 modified when the user holds down a certain
567 combination of keys on the (special) keyboard when
570 - Serial Download Echo Mode:
572 If defined to 1, all characters received during a
573 serial download (using the "loads" command) are
574 echoed back. This might be needed by some terminal
575 emulations (like "cu"), but may as well just take
576 time on others. This setting #define's the initial
577 value of the "loads_echo" environment variable.
579 - Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
581 Select one of the baudrates listed in
582 CFG_BAUDRATE_TABLE, see below.
586 Most monitor functions can be selected (or
587 de-selected) by adjusting the definition of
588 CONFIG_COMMANDS; to select individual functions,
589 #define CONFIG_COMMANDS by "OR"ing any of the
592 #define enables commands:
593 -------------------------
594 CFG_CMD_ASKENV * ask for env variable
595 CFG_CMD_AUTOSCRIPT Autoscript Support
597 CFG_CMD_BEDBUG Include BedBug Debugger
598 CFG_CMD_BMP * BMP support
600 CFG_CMD_CACHE icache, dcache
601 CFG_CMD_CONSOLE coninfo
602 CFG_CMD_DATE * support for RTC, date/time...
603 CFG_CMD_DHCP DHCP support
604 CFG_CMD_DIAG * Diagnostics
605 CFG_CMD_DOC * Disk-On-Chip Support
606 CFG_CMD_DTT Digital Therm and Thermostat
607 CFG_CMD_ECHO * echo arguments
608 CFG_CMD_EEPROM * EEPROM read/write support
609 CFG_CMD_ELF bootelf, bootvx
611 CFG_CMD_FDC * Floppy Disk Support
612 CFG_CMD_FAT FAT partition support
613 CFG_CMD_FDOS * Dos diskette Support
614 CFG_CMD_FLASH flinfo, erase, protect
615 CFG_CMD_FPGA FPGA device initialization support
616 CFG_CMD_HWFLOW * RTS/CTS hw flow control
617 CFG_CMD_I2C * I2C serial bus support
618 CFG_CMD_IDE * IDE harddisk support
620 CFG_CMD_IMLS List all found images
621 CFG_CMD_IMMAP * IMMR dump support
622 CFG_CMD_IRQ * irqinfo
623 CFG_CMD_JFFS2 * JFFS2 Support
627 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
629 CFG_CMD_MISC Misc functions like sleep etc
630 CFG_CMD_MMC MMC memory mapped support
631 CFG_CMD_MII MII utility commands
632 CFG_CMD_NAND * NAND support
633 CFG_CMD_NET bootp, tftpboot, rarpboot
634 CFG_CMD_PCI * pciinfo
635 CFG_CMD_PCMCIA * PCMCIA support
636 CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
637 CFG_CMD_PORTIO Port I/O
638 CFG_CMD_REGINFO * Register dump
639 CFG_CMD_RUN run command in env variable
640 CFG_CMD_SAVES save S record dump
641 CFG_CMD_SCSI * SCSI Support
642 CFG_CMD_SDRAM * print SDRAM configuration information
643 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
644 CFG_CMD_SPI * SPI serial bus support
645 CFG_CMD_USB * USB support
646 CFG_CMD_VFD * VFD support (TRAB)
647 CFG_CMD_BSP * Board SPecific functions
648 -----------------------------------------------
651 CFG_CMD_DFL Default configuration; at the moment
652 this is includes all commands, except
653 the ones marked with "*" in the list
656 If you don't define CONFIG_COMMANDS it defaults to
657 CFG_CMD_DFL in include/cmd_confdefs.h. A board can
658 override the default settings in the respective
661 EXAMPLE: If you want all functions except of network
662 support you can write:
664 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
667 Note: Don't enable the "icache" and "dcache" commands
668 (configuration option CFG_CMD_CACHE) unless you know
669 what you (and your U-Boot users) are doing. Data
670 cache cannot be enabled on systems like the 8xx or
671 8260 (where accesses to the IMMR region must be
672 uncached), and it cannot be disabled on all other
673 systems where we (mis-) use the data cache to hold an
674 initial stack and some data.
677 XXX - this list needs to get updated!
681 If this variable is defined, it enables watchdog
682 support. There must be support in the platform specific
683 code for a watchdog. For the 8xx and 8260 CPUs, the
684 SIU Watchdog feature is enabled in the SYPCR
688 CONFIG_VERSION_VARIABLE
689 If this variable is defined, an environment variable
690 named "ver" is created by U-Boot showing the U-Boot
691 version as printed by the "version" command.
692 This variable is readonly.
696 When CFG_CMD_DATE is selected, the type of the RTC
697 has to be selected, too. Define exactly one of the
700 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
701 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
702 CONFIG_RTC_MC146818 - use MC146818 RTC
703 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
704 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
705 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
706 CONFIG_RTC_DS164x - use Dallas DS164x RTC
708 Note that if the RTC uses I2C, then the I2C interface
709 must also be configured. See I2C Support, below.
713 When CONFIG_TIMESTAMP is selected, the timestamp
714 (date and time) of an image is printed by image
715 commands like bootm or iminfo. This option is
716 automatically enabled when you select CFG_CMD_DATE .
719 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
720 and/or CONFIG_ISO_PARTITION
722 If IDE or SCSI support is enabled (CFG_CMD_IDE or
723 CFG_CMD_SCSI) you must configure support for at least
724 one partition type as well.
727 CONFIG_IDE_RESET_ROUTINE
729 Set this to define that instead of a reset Pin, the
730 routine ide_set_reset(int idereset) will be used.
735 Set this to enable ATAPI support.
738 At the moment only there is only support for the
739 SYM53C8XX SCSI controller; define
740 CONFIG_SCSI_SYM53C8XX to enable it.
742 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
743 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
744 CFG_SCSI_MAX_LUN] can be adjusted to define the
745 maximum numbers of LUNs, SCSI ID's and target
747 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
749 - NETWORK Support (PCI):
751 Support for Intel 8254x gigabit chips.
754 Support for Intel 82557/82559/82559ER chips.
755 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
756 write routine for first time initialisation.
759 Support for Digital 2114x chips.
760 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
761 modem chip initialisation (KS8761/QS6611).
764 Support for National dp83815 chips.
767 Support for National dp8382[01] gigabit chips.
769 - NETWORK Support (other):
771 CONFIG_DRIVER_LAN91C96
772 Support for SMSC's LAN91C96 chips.
775 Define this to hold the physical address
776 of the LAN91C96's I/O space
778 CONFIG_LAN91C96_USE_32_BIT
779 Define this to enable 32 bit addressing
782 At the moment only the UHCI host controller is
783 supported (PIP405, MIP405); define
784 CONFIG_USB_UHCI to enable it.
785 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
786 end define CONFIG_USB_STORAGE to enable the USB
789 Supported are USB Keyboards and USB Floppy drives
793 The MMC controller on the Intel PXA is supported. To
794 enable this define CONFIG_MMC. The MMC can be
795 accessed from the boot prompt by mapping the device
796 to physical memory similar to flash. Command line is
797 enabled with CFG_CMD_MMC. The MMC driver also works with
798 the FAT fs. This is enabled with CFG_CMD_FAT.
803 Define this to enable standard (PC-Style) keyboard
807 Standard PC keyboard driver with US (is default) and
808 GERMAN key layout (switch via environment 'keymap=de') support.
809 Export function i8042_kbd_init, i8042_tstc and i8042_getc
810 for cfb_console. Supports cursor blinking.
815 Define this to enable video support (for output to
820 Enable Chips & Technologies 69000 Video chip
822 CONFIG_VIDEO_SMI_LYNXEM
823 Enable Silicon Motion SMI 712/710/810 Video chip
824 Videomode are selected via environment 'videomode' with
825 standard LiLo mode numbers.
826 Following modes are supported (* is default):
828 800x600 1024x768 1280x1024
829 256 (8bit) 303* 305 307
830 65536 (16bit) 314 317 31a
831 16,7 Mill (24bit) 315 318 31b
832 (i.e. setenv videomode 317; saveenv; reset;)
834 CONFIG_VIDEO_SED13806
835 Enable Epson SED13806 driver. This driver supports 8bpp
836 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
837 or CONFIG_VIDEO_SED13806_16BPP
842 Define this to enable a custom keyboard support.
843 This simply calls drv_keyboard_init() which must be
844 defined in your board-specific files.
845 The only board using this so far is RBC823.
847 - LCD Support: CONFIG_LCD
849 Define this to enable LCD support (for output to LCD
850 display); also select one of the supported displays
851 by defining one of these:
853 CONFIG_NEC_NL6648AC33:
855 NEC NL6648AC33-18. Active, color, single scan.
857 CONFIG_NEC_NL6648BC20
859 NEC NL6648BC20-08. 6.5", 640x480.
860 Active, color, single scan.
864 Sharp 320x240. Active, color, single scan.
865 It isn't 16x9, and I am not sure what it is.
867 CONFIG_SHARP_LQ64D341
869 Sharp LQ64D341 display, 640x480.
870 Active, color, single scan.
874 HLD1045 display, 640x480.
875 Active, color, single scan.
879 Optrex CBL50840-2 NF-FW 99 22 M5
881 Hitachi LMG6912RPFC-00T
885 320x240. Black & white.
887 Normally display is black on white background; define
888 CFG_WHITE_ON_BLACK to get it inverted.
890 - Splash Screen Support: CONFIG_SPLASH_SCREEN
892 If this option is set, the environment is checked for
893 a variable "splashimage". If found, the usual display
894 of logo, copyright and system information on the LCD
895 is supressed and the BMP image at the address
896 specified in "splashimage" is loaded instead. The
897 console is redirected to the "nulldev", too. This
898 allows for a "silent" boot where a splash screen is
899 loaded very quickly after power-on.
901 - Compression support:
904 If this option is set, support for bzip2 compressed
905 images is included. If not, only uncompressed and gzip
906 compressed images are supported.
908 NOTE: the bzip2 algorithm requires a lot of RAM, so
909 the malloc area (as defined by CFG_MALLOC_LEN) should
917 Define a default value for ethernet address to use
918 for the respective ethernet interface, in case this
919 is not determined automatically.
924 Define a default value for the IP address to use for
925 the default ethernet interface, in case this is not
926 determined through e.g. bootp.
931 Defines a default value for theIP address of a TFTP
932 server to contact when using the "tftboot" command.
934 - BOOTP Recovery Mode:
935 CONFIG_BOOTP_RANDOM_DELAY
937 If you have many targets in a network that try to
938 boot using BOOTP, you may want to avoid that all
939 systems send out BOOTP requests at precisely the same
940 moment (which would happen for instance at recovery
941 from a power failure, when all systems will try to
942 boot, thus flooding the BOOTP server. Defining
943 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
944 inserted before sending out BOOTP requests. The
945 following delays are insterted then:
947 1st BOOTP request: delay 0 ... 1 sec
948 2nd BOOTP request: delay 0 ... 2 sec
949 3rd BOOTP request: delay 0 ... 4 sec
951 BOOTP requests: delay 0 ... 8 sec
953 - DHCP Advanced Options:
956 You can fine tune the DHCP functionality by adding
957 these flags to the CONFIG_BOOTP_MASK define:
959 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
960 serverip from a DHCP server, it is possible that more
961 than one DNS serverip is offered to the client.
962 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
963 serverip will be stored in the additional environment
964 variable "dnsip2". The first DNS serverip is always
965 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
966 is added to the CONFIG_BOOTP_MASK.
968 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
969 to do a dynamic update of a DNS server. To do this, they
970 need the hostname of the DHCP requester.
971 If CONFIG_BOOP_SEND_HOSTNAME is added to the
972 CONFIG_BOOTP_MASK, the content of the "hostname"
973 environment variable is passed as option 12 to
976 - Status LED: CONFIG_STATUS_LED
978 Several configurations allow to display the current
979 status using a LED. For instance, the LED will blink
980 fast while running U-Boot code, stop blinking as
981 soon as a reply to a BOOTP request was received, and
982 start blinking slow once the Linux kernel is running
983 (supported by a status LED driver in the Linux
984 kernel). Defining CONFIG_STATUS_LED enables this
987 - CAN Support: CONFIG_CAN_DRIVER
989 Defining CONFIG_CAN_DRIVER enables CAN driver support
990 on those systems that support this (optional)
991 feature, like the TQM8xxL modules.
993 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
995 These enable I2C serial bus commands. Defining either of
996 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
997 include the appropriate I2C driver for the selected cpu.
999 This will allow you to use i2c commands at the u-boot
1000 command line (as long as you set CFG_CMD_I2C in
1001 CONFIG_COMMANDS) and communicate with i2c based realtime
1002 clock chips. See common/cmd_i2c.c for a description of the
1003 command line interface.
1005 CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
1007 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1008 bit-banging) driver instead of CPM or similar hardware
1011 There are several other quantities that must also be
1012 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1014 In both cases you will need to define CFG_I2C_SPEED
1015 to be the frequency (in Hz) at which you wish your i2c bus
1016 to run and CFG_I2C_SLAVE to be the address of this node (ie
1017 the cpu's i2c node address).
1019 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1020 sets the cpu up as a master node and so its address should
1021 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1022 p.16-473). So, set CFG_I2C_SLAVE to 0.
1024 That's all that's required for CONFIG_HARD_I2C.
1026 If you use the software i2c interface (CONFIG_SOFT_I2C)
1027 then the following macros need to be defined (examples are
1028 from include/configs/lwmon.h):
1032 (Optional). Any commands necessary to enable the I2C
1033 controller or configure ports.
1035 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1039 (Only for MPC8260 CPU). The I/O port to use (the code
1040 assumes both bits are on the same port). Valid values
1041 are 0..3 for ports A..D.
1045 The code necessary to make the I2C data line active
1046 (driven). If the data line is open collector, this
1049 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1053 The code necessary to make the I2C data line tri-stated
1054 (inactive). If the data line is open collector, this
1057 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1061 Code that returns TRUE if the I2C data line is high,
1064 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1068 If <bit> is TRUE, sets the I2C data line high. If it
1069 is FALSE, it clears it (low).
1071 eg: #define I2C_SDA(bit) \
1072 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1073 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1077 If <bit> is TRUE, sets the I2C clock line high. If it
1078 is FALSE, it clears it (low).
1080 eg: #define I2C_SCL(bit) \
1081 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1082 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1086 This delay is invoked four times per clock cycle so this
1087 controls the rate of data transfer. The data rate thus
1088 is 1 / (I2C_DELAY * 4). Often defined to be something
1091 #define I2C_DELAY udelay(2)
1095 When a board is reset during an i2c bus transfer
1096 chips might think that the current transfer is still
1097 in progress. On some boards it is possible to access
1098 the i2c SCLK line directly, either by using the
1099 processor pin as a GPIO or by having a second pin
1100 connected to the bus. If this option is defined a
1101 custom i2c_init_board() routine in boards/xxx/board.c
1102 is run early in the boot sequence.
1104 - SPI Support: CONFIG_SPI
1106 Enables SPI driver (so far only tested with
1107 SPI EEPROM, also an instance works with Crystal A/D and
1108 D/As on the SACSng board)
1112 Enables extended (16-bit) SPI EEPROM addressing.
1113 (symmetrical to CONFIG_I2C_X)
1117 Enables a software (bit-bang) SPI driver rather than
1118 using hardware support. This is a general purpose
1119 driver that only requires three general I/O port pins
1120 (two outputs, one input) to function. If this is
1121 defined, the board configuration must define several
1122 SPI configuration items (port pins to use, etc). For
1123 an example, see include/configs/sacsng.h.
1125 - FPGA Support: CONFIG_FPGA_COUNT
1127 Specify the number of FPGA devices to support.
1131 Used to specify the types of FPGA devices. For
1133 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1135 CFG_FPGA_PROG_FEEDBACK
1137 Enable printing of hash marks during FPGA
1142 Enable checks on FPGA configuration interface busy
1143 status by the configuration function. This option
1144 will require a board or device specific function to
1149 If defined, a function that provides delays in the
1150 FPGA configuration driver.
1152 CFG_FPGA_CHECK_CTRLC
1154 Allow Control-C to interrupt FPGA configuration
1156 CFG_FPGA_CHECK_ERROR
1158 Check for configuration errors during FPGA bitfile
1159 loading. For example, abort during Virtex II
1160 configuration if the INIT_B line goes low (which
1161 indicated a CRC error).
1165 Maximum time to wait for the INIT_B line to deassert
1166 after PROB_B has been deasserted during a Virtex II
1167 FPGA configuration sequence. The default time is 500 mS.
1171 Maximum time to wait for BUSY to deassert during
1172 Virtex II FPGA configuration. The default is 5 mS.
1174 CFG_FPGA_WAIT_CONFIG
1176 Time to wait after FPGA configuration. The default is
1179 - FPGA Support: CONFIG_FPGA_COUNT
1181 Specify the number of FPGA devices to support.
1185 Used to specify the types of FPGA devices. For example,
1186 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1188 CFG_FPGA_PROG_FEEDBACK
1190 Enable printing of hash marks during FPGA configuration.
1194 Enable checks on FPGA configuration interface busy
1195 status by the configuration function. This option
1196 will require a board or device specific function to
1201 If defined, a function that provides delays in the FPGA
1202 configuration driver.
1204 CFG_FPGA_CHECK_CTRLC
1205 Allow Control-C to interrupt FPGA configuration
1207 CFG_FPGA_CHECK_ERROR
1209 Check for configuration errors during FPGA bitfile
1210 loading. For example, abort during Virtex II
1211 configuration if the INIT_B line goes low (which
1212 indicated a CRC error).
1216 Maximum time to wait for the INIT_B line to deassert
1217 after PROB_B has been deasserted during a Virtex II
1218 FPGA configuration sequence. The default time is 500
1223 Maximum time to wait for BUSY to deassert during
1224 Virtex II FPGA configuration. The default is 5 mS.
1226 CFG_FPGA_WAIT_CONFIG
1228 Time to wait after FPGA configuration. The default is
1231 - Configuration Management:
1234 If defined, this string will be added to the U-Boot
1235 version information (U_BOOT_VERSION)
1237 - Vendor Parameter Protection:
1239 U-Boot considers the values of the environment
1240 variables "serial#" (Board Serial Number) and
1241 "ethaddr" (Ethernet Address) to be parameters that
1242 are set once by the board vendor / manufacturer, and
1243 protects these variables from casual modification by
1244 the user. Once set, these variables are read-only,
1245 and write or delete attempts are rejected. You can
1246 change this behviour:
1248 If CONFIG_ENV_OVERWRITE is #defined in your config
1249 file, the write protection for vendor parameters is
1250 completely disabled. Anybody can change or delete
1253 Alternatively, if you #define _both_ CONFIG_ETHADDR
1254 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1255 ethernet address is installed in the environment,
1256 which can be changed exactly ONCE by the user. [The
1257 serial# is unaffected by this, i. e. it remains
1263 Define this variable to enable the reservation of
1264 "protected RAM", i. e. RAM which is not overwritten
1265 by U-Boot. Define CONFIG_PRAM to hold the number of
1266 kB you want to reserve for pRAM. You can overwrite
1267 this default value by defining an environment
1268 variable "pram" to the number of kB you want to
1269 reserve. Note that the board info structure will
1270 still show the full amount of RAM. If pRAM is
1271 reserved, a new environment variable "mem" will
1272 automatically be defined to hold the amount of
1273 remaining RAM in a form that can be passed as boot
1274 argument to Linux, for instance like that:
1276 setenv bootargs ... mem=\$(mem)
1279 This way you can tell Linux not to use this memory,
1280 either, which results in a memory region that will
1281 not be affected by reboots.
1283 *WARNING* If your board configuration uses automatic
1284 detection of the RAM size, you must make sure that
1285 this memory test is non-destructive. So far, the
1286 following board configurations are known to be
1289 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1290 HERMES, IP860, RPXlite, LWMON, LANTEC,
1291 PCU_E, FLAGADM, TQM8260
1296 Define this variable to stop the system in case of a
1297 fatal error, so that you have to reset it manually.
1298 This is probably NOT a good idea for an embedded
1299 system where you want to system to reboot
1300 automatically as fast as possible, but it may be
1301 useful during development since you can try to debug
1302 the conditions that lead to the situation.
1304 CONFIG_NET_RETRY_COUNT
1306 This variable defines the number of retries for
1307 network operations like ARP, RARP, TFTP, or BOOTP
1308 before giving up the operation. If not defined, a
1309 default value of 5 is used.
1311 - Command Interpreter:
1314 Define this variable to enable the "hush" shell (from
1315 Busybox) as command line interpreter, thus enabling
1316 powerful command line syntax like
1317 if...then...else...fi conditionals or `&&' and '||'
1318 constructs ("shell scripts").
1320 If undefined, you get the old, much simpler behaviour
1321 with a somewhat smaller memory footprint.
1326 This defines the secondary prompt string, which is
1327 printed when the command interpreter needs more input
1328 to complete a command. Usually "> ".
1332 In the current implementation, the local variables
1333 space and global environment variables space are
1334 separated. Local variables are those you define by
1335 simply typing `name=value'. To access a local
1336 variable later on, you have write `$name' or
1337 `${name}'; to execute the contents of a variable
1338 directly type `$name' at the command prompt.
1340 Global environment variables are those you use
1341 setenv/printenv to work with. To run a command stored
1342 in such a variable, you need to use the run command,
1343 and you must not use the '$' sign to access them.
1345 To store commands and special characters in a
1346 variable, please use double quotation marks
1347 surrounding the whole text of the variable, instead
1348 of the backslashes before semicolons and special
1351 - Default Environment
1352 CONFIG_EXTRA_ENV_SETTINGS
1354 Define this to contain any number of null terminated
1355 strings (variable = value pairs) that will be part of
1356 the default environment compiled into the boot image.
1358 For example, place something like this in your
1359 board's config file:
1361 #define CONFIG_EXTRA_ENV_SETTINGS \
1365 Warning: This method is based on knowledge about the
1366 internal format how the environment is stored by the
1367 U-Boot code. This is NOT an official, exported
1368 interface! Although it is unlikely that this format
1369 will change soon, there is no guarantee either.
1370 You better know what you are doing here.
1372 Note: overly (ab)use of the default environment is
1373 discouraged. Make sure to check other ways to preset
1374 the environment like the autoscript function or the
1378 CONFIG_HAS_DATAFLASH
1380 Defining this option enables DataFlash features and
1381 allows to read/write in Dataflash via the standard
1384 - Show boot progress
1385 CONFIG_SHOW_BOOT_PROGRESS
1387 Defining this option allows to add some board-
1388 specific code (calling a user-provided function
1389 "show_boot_progress(int)") that enables you to show
1390 the system's boot progress on some display (for
1391 example, some LED's) on your board. At the moment,
1392 the following checkpoints are implemented:
1395 1 common/cmd_bootm.c before attempting to boot an image
1396 -1 common/cmd_bootm.c Image header has bad magic number
1397 2 common/cmd_bootm.c Image header has correct magic number
1398 -2 common/cmd_bootm.c Image header has bad checksum
1399 3 common/cmd_bootm.c Image header has correct checksum
1400 -3 common/cmd_bootm.c Image data has bad checksum
1401 4 common/cmd_bootm.c Image data has correct checksum
1402 -4 common/cmd_bootm.c Image is for unsupported architecture
1403 5 common/cmd_bootm.c Architecture check OK
1404 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1405 6 common/cmd_bootm.c Image Type check OK
1406 -6 common/cmd_bootm.c gunzip uncompression error
1407 -7 common/cmd_bootm.c Unimplemented compression type
1408 7 common/cmd_bootm.c Uncompression OK
1409 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1410 8 common/cmd_bootm.c Image Type check OK
1411 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1412 9 common/cmd_bootm.c Start initial ramdisk verification
1413 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1414 -11 common/cmd_bootm.c Ramdisk header has bad checksum
1415 10 common/cmd_bootm.c Ramdisk header is OK
1416 -12 common/cmd_bootm.c Ramdisk data has bad checksum
1417 11 common/cmd_bootm.c Ramdisk data has correct checksum
1418 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1419 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1420 13 common/cmd_bootm.c Start multifile image verification
1421 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1422 15 common/cmd_bootm.c All preparation done, transferring control to OS
1424 -1 common/cmd_doc.c Bad usage of "doc" command
1425 -1 common/cmd_doc.c No boot device
1426 -1 common/cmd_doc.c Unknown Chip ID on boot device
1427 -1 common/cmd_doc.c Read Error on boot device
1428 -1 common/cmd_doc.c Image header has bad magic number
1430 -1 common/cmd_ide.c Bad usage of "ide" command
1431 -1 common/cmd_ide.c No boot device
1432 -1 common/cmd_ide.c Unknown boot device
1433 -1 common/cmd_ide.c Unknown partition table
1434 -1 common/cmd_ide.c Invalid partition type
1435 -1 common/cmd_ide.c Read Error on boot device
1436 -1 common/cmd_ide.c Image header has bad magic number
1438 -1 common/cmd_nand.c Bad usage of "nand" command
1439 -1 common/cmd_nand.c No boot device
1440 -1 common/cmd_nand.c Unknown Chip ID on boot device
1441 -1 common/cmd_nand.c Read Error on boot device
1442 -1 common/cmd_nand.c Image header has bad magic number
1444 -1 common/env_common.c Environment has a bad CRC, using default
1450 [so far only for SMDK2400 and TRAB boards]
1452 - Modem support endable:
1453 CONFIG_MODEM_SUPPORT
1455 - RTS/CTS Flow control enable:
1458 - Modem debug support:
1459 CONFIG_MODEM_SUPPORT_DEBUG
1461 Enables debugging stuff (char screen[1024], dbg())
1462 for modem support. Useful only with BDI2000.
1466 In the target system modem support is enabled when a
1467 specific key (key combination) is pressed during
1468 power-on. Otherwise U-Boot will boot normally
1469 (autoboot). The key_pressed() fuction is called from
1470 board_init(). Currently key_pressed() is a dummy
1471 function, returning 1 and thus enabling modem
1474 If there are no modem init strings in the
1475 environment, U-Boot proceed to autoboot; the
1476 previous output (banner, info printfs) will be
1479 See also: doc/README.Modem
1482 Configuration Settings:
1483 -----------------------
1485 - CFG_LONGHELP: Defined when you want long help messages included;
1486 undefine this when you're short of memory.
1488 - CFG_PROMPT: This is what U-Boot prints on the console to
1489 prompt for user input.
1491 - CFG_CBSIZE: Buffer size for input from the Console
1493 - CFG_PBSIZE: Buffer size for Console output
1495 - CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1497 - CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1498 the application (usually a Linux kernel) when it is
1501 - CFG_BAUDRATE_TABLE:
1502 List of legal baudrate settings for this board.
1504 - CFG_CONSOLE_INFO_QUIET
1505 Suppress display of console information at boot.
1507 - CFG_CONSOLE_IS_IN_ENV
1508 If the board specific function
1509 extern int overwrite_console (void);
1510 returns 1, the stdin, stderr and stdout are switched to the
1511 serial port, else the settings in the environment are used.
1513 - CFG_CONSOLE_OVERWRITE_ROUTINE
1514 Enable the call to overwrite_console().
1516 - CFG_CONSOLE_ENV_OVERWRITE
1517 Enable overwrite of previous console environment settings.
1519 - CFG_MEMTEST_START, CFG_MEMTEST_END:
1520 Begin and End addresses of the area used by the
1524 Enable an alternate, more extensive memory test.
1526 - CFG_MEMTEST_SCRATCH:
1527 Scratch address used by the alternate memory test
1528 You only need to set this if address zero isn't writeable
1530 - CFG_TFTP_LOADADDR:
1531 Default load address for network file downloads
1533 - CFG_LOADS_BAUD_CHANGE:
1534 Enable temporary baudrate change while serial download
1537 Physical start address of SDRAM. _Must_ be 0 here.
1540 Physical start address of Motherboard I/O (if using a
1544 Physical start address of Flash memory.
1547 Physical start address of boot monitor code (set by
1548 make config files to be same as the text base address
1549 (TEXT_BASE) used when linking) - same as
1550 CFG_FLASH_BASE when booting from flash.
1553 Size of memory reserved for monitor code, used to
1554 determine _at_compile_time_ (!) if the environment is
1555 embedded within the U-Boot image, or in a separate
1559 Size of DRAM reserved for malloc() use.
1562 Maximum size of memory mapped by the startup code of
1563 the Linux kernel; all data that must be processed by
1564 the Linux kernel (bd_info, boot arguments, eventually
1565 initrd image) must be put below this limit.
1567 - CFG_MAX_FLASH_BANKS:
1568 Max number of Flash memory banks
1570 - CFG_MAX_FLASH_SECT:
1571 Max number of sectors on a Flash chip
1573 - CFG_FLASH_ERASE_TOUT:
1574 Timeout for Flash erase operations (in ms)
1576 - CFG_FLASH_WRITE_TOUT:
1577 Timeout for Flash write operations (in ms)
1579 - CFG_FLASH_LOCK_TOUT
1580 Timeout for Flash set sector lock bit operation (in ms)
1582 - CFG_FLASH_UNLOCK_TOUT
1583 Timeout for Flash clear lock bits operation (in ms)
1585 - CFG_FLASH_PROTECTION
1586 If defined, hardware flash sectors protection is used
1587 instead of U-Boot software protection.
1589 - CFG_DIRECT_FLASH_TFTP:
1591 Enable TFTP transfers directly to flash memory;
1592 without this option such a download has to be
1593 performed in two steps: (1) download to RAM, and (2)
1594 copy from RAM to flash.
1596 The two-step approach is usually more reliable, since
1597 you can check if the download worked before you erase
1598 the flash, but in some situations (when sytem RAM is
1599 too limited to allow for a tempory copy of the
1600 downloaded image) this option may be very useful.
1603 Define if the flash driver uses extra elements in the
1604 common flash structure for storing flash geometry
1606 - CFG_RX_ETH_BUFFER:
1607 Defines the number of ethernet receive buffers. On some
1608 ethernet controllers it is recommended to set this value
1609 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1610 buffers can be full shortly after enabling the interface
1611 on high ethernet traffic.
1612 Defaults to 4 if not defined.
1614 The following definitions that deal with the placement and management
1615 of environment data (variable area); in general, we support the
1616 following configurations:
1618 - CFG_ENV_IS_IN_FLASH:
1620 Define this if the environment is in flash memory.
1622 a) The environment occupies one whole flash sector, which is
1623 "embedded" in the text segment with the U-Boot code. This
1624 happens usually with "bottom boot sector" or "top boot
1625 sector" type flash chips, which have several smaller
1626 sectors at the start or the end. For instance, such a
1627 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1628 such a case you would place the environment in one of the
1629 4 kB sectors - with U-Boot code before and after it. With
1630 "top boot sector" type flash chips, you would put the
1631 environment in one of the last sectors, leaving a gap
1632 between U-Boot and the environment.
1636 Offset of environment data (variable area) to the
1637 beginning of flash memory; for instance, with bottom boot
1638 type flash chips the second sector can be used: the offset
1639 for this sector is given here.
1641 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1645 This is just another way to specify the start address of
1646 the flash sector containing the environment (instead of
1649 - CFG_ENV_SECT_SIZE:
1651 Size of the sector containing the environment.
1654 b) Sometimes flash chips have few, equal sized, BIG sectors.
1655 In such a case you don't want to spend a whole sector for
1660 If you use this in combination with CFG_ENV_IS_IN_FLASH
1661 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1662 of this flash sector for the environment. This saves
1663 memory for the RAM copy of the environment.
1665 It may also save flash memory if you decide to use this
1666 when your environment is "embedded" within U-Boot code,
1667 since then the remainder of the flash sector could be used
1668 for U-Boot code. It should be pointed out that this is
1669 STRONGLY DISCOURAGED from a robustness point of view:
1670 updating the environment in flash makes it always
1671 necessary to erase the WHOLE sector. If something goes
1672 wrong before the contents has been restored from a copy in
1673 RAM, your target system will be dead.
1675 - CFG_ENV_ADDR_REDUND
1678 These settings describe a second storage area used to hold
1679 a redundand copy of the environment data, so that there is
1680 a valid backup copy in case there is a power failure during
1681 a "saveenv" operation.
1683 BE CAREFUL! Any changes to the flash layout, and some changes to the
1684 source code will make it necessary to adapt <board>/u-boot.lds*
1688 - CFG_ENV_IS_IN_NVRAM:
1690 Define this if you have some non-volatile memory device
1691 (NVRAM, battery buffered SRAM) which you want to use for the
1697 These two #defines are used to determin the memory area you
1698 want to use for environment. It is assumed that this memory
1699 can just be read and written to, without any special
1702 BE CAREFUL! The first access to the environment happens quite early
1703 in U-Boot initalization (when we try to get the setting of for the
1704 console baudrate). You *MUST* have mappend your NVRAM area then, or
1707 Please note that even with NVRAM we still use a copy of the
1708 environment in RAM: we could work on NVRAM directly, but we want to
1709 keep settings there always unmodified except somebody uses "saveenv"
1710 to save the current settings.
1713 - CFG_ENV_IS_IN_EEPROM:
1715 Use this if you have an EEPROM or similar serial access
1716 device and a driver for it.
1721 These two #defines specify the offset and size of the
1722 environment area within the total memory of your EEPROM.
1724 - CFG_I2C_EEPROM_ADDR:
1725 If defined, specified the chip address of the EEPROM device.
1726 The default address is zero.
1728 - CFG_EEPROM_PAGE_WRITE_BITS:
1729 If defined, the number of bits used to address bytes in a
1730 single page in the EEPROM device. A 64 byte page, for example
1731 would require six bits.
1733 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1734 If defined, the number of milliseconds to delay between
1735 page writes. The default is zero milliseconds.
1737 - CFG_I2C_EEPROM_ADDR_LEN:
1738 The length in bytes of the EEPROM memory array address. Note
1739 that this is NOT the chip address length!
1742 The size in bytes of the EEPROM device.
1745 - CFG_SPI_INIT_OFFSET
1747 Defines offset to the initial SPI buffer area in DPRAM. The
1748 area is used at an early stage (ROM part) if the environment
1749 is configured to reside in the SPI EEPROM: We need a 520 byte
1750 scratch DPRAM area. It is used between the two initialization
1751 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1752 to be a good choice since it makes it far enough from the
1753 start of the data area as well as from the stack pointer.
1755 Please note that the environment is read-only as long as the monitor
1756 has been relocated to RAM and a RAM copy of the environment has been
1757 created; also, when using EEPROM you will have to use getenv_r()
1758 until then to read environment variables.
1760 The environment is protected by a CRC32 checksum. Before the monitor
1761 is relocated into RAM, as a result of a bad CRC you will be working
1762 with the compiled-in default environment - *silently*!!! [This is
1763 necessary, because the first environment variable we need is the
1764 "baudrate" setting for the console - if we have a bad CRC, we don't
1765 have any device yet where we could complain.]
1767 Note: once the monitor has been relocated, then it will complain if
1768 the default environment is used; a new CRC is computed as soon as you
1769 use the "saveenv" command to store a valid environment.
1771 - CFG_FAULT_ECHO_LINK_DOWN:
1772 Echo the inverted Ethernet link state to the fault LED.
1774 Note: If this option is active, then CFG_FAULT_MII_ADDR
1775 also needs to be defined.
1777 - CFG_FAULT_MII_ADDR:
1778 MII address of the PHY to check for the Ethernet link state.
1780 Low Level (hardware related) configuration options:
1781 ---------------------------------------------------
1783 - CFG_CACHELINE_SIZE:
1784 Cache Line Size of the CPU.
1787 Default address of the IMMR after system reset.
1789 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
1790 and RPXsuper) to be able to adjust the position of
1791 the IMMR register after a reset.
1793 - Floppy Disk Support:
1794 CFG_FDC_DRIVE_NUMBER
1796 the default drive number (default value 0)
1800 defines the spacing between fdc chipset registers
1805 defines the offset of register from address. It
1806 depends on which part of the data bus is connected to
1807 the fdc chipset. (default value 0)
1809 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1810 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1813 if CFG_FDC_HW_INIT is defined, then the function
1814 fdc_hw_init() is called at the beginning of the FDC
1815 setup. fdc_hw_init() must be provided by the board
1816 source code. It is used to make hardware dependant
1819 - CFG_IMMR: Physical address of the Internal Memory Mapped
1820 Register; DO NOT CHANGE! (11-4)
1821 [MPC8xx systems only]
1823 - CFG_INIT_RAM_ADDR:
1825 Start address of memory area that can be used for
1826 initial data and stack; please note that this must be
1827 writable memory that is working WITHOUT special
1828 initialization, i. e. you CANNOT use normal RAM which
1829 will become available only after programming the
1830 memory controller and running certain initialization
1833 U-Boot uses the following memory types:
1834 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
1835 - MPC824X: data cache
1836 - PPC4xx: data cache
1838 - CFG_GBL_DATA_OFFSET:
1840 Offset of the initial data structure in the memory
1841 area defined by CFG_INIT_RAM_ADDR. Usually
1842 CFG_GBL_DATA_OFFSET is chosen such that the initial
1843 data is located at the end of the available space
1844 (sometimes written as (CFG_INIT_RAM_END -
1845 CFG_INIT_DATA_SIZE), and the initial stack is just
1846 below that area (growing from (CFG_INIT_RAM_ADDR +
1847 CFG_GBL_DATA_OFFSET) downward.
1850 On the MPC824X (or other systems that use the data
1851 cache for initial memory) the address chosen for
1852 CFG_INIT_RAM_ADDR is basically arbitrary - it must
1853 point to an otherwise UNUSED address space between
1854 the top of RAM and the start of the PCI space.
1856 - CFG_SIUMCR: SIU Module Configuration (11-6)
1858 - CFG_SYPCR: System Protection Control (11-9)
1860 - CFG_TBSCR: Time Base Status and Control (11-26)
1862 - CFG_PISCR: Periodic Interrupt Status and Control (11-31)
1864 - CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
1866 - CFG_SCCR: System Clock and reset Control Register (15-27)
1868 - CFG_OR_TIMING_SDRAM:
1872 periodic timer for refresh
1874 - CFG_DER: Debug Event Register (37-47)
1876 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
1877 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
1878 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
1880 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
1882 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
1883 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
1884 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
1885 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
1887 - CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
1888 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
1889 Machine Mode Register and Memory Periodic Timer
1890 Prescaler definitions (SDRAM timing)
1892 - CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
1893 enable I2C microcode relocation patch (MPC8xx);
1894 define relocation offset in DPRAM [DSP2]
1896 - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
1897 enable SPI microcode relocation patch (MPC8xx);
1898 define relocation offset in DPRAM [SCC4]
1901 Use OSCM clock mode on MBX8xx board. Be careful,
1902 wrong setting might damage your board. Read
1903 doc/README.MBX before setting this variable!
1905 - CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
1906 Offset of the bootmode word in DPRAM used by post
1907 (Power On Self Tests). This definition overrides
1908 #define'd default value in commproc.h resp.
1911 - CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
1912 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
1913 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
1914 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
1915 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
1916 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
1917 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
1918 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
1919 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
1921 Building the Software:
1922 ======================
1924 Building U-Boot has been tested in native PPC environments (on a
1925 PowerBook G3 running LinuxPPC 2000) and in cross environments
1926 (running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
1929 If you are not using a native PPC environment, it is assumed that you
1930 have the GNU cross compiling tools available in your path and named
1931 with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
1932 you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
1933 the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
1936 CROSS_COMPILE = ppc_4xx-
1939 U-Boot is intended to be simple to build. After installing the
1940 sources you must configure U-Boot for one specific board type. This
1945 where "NAME_config" is the name of one of the existing
1946 configurations; the following names are supported:
1948 ADCIOP_config GTH_config TQM850L_config
1949 ADS860_config IP860_config TQM855L_config
1950 AR405_config IVML24_config TQM860L_config
1951 CANBT_config IVMS8_config WALNUT405_config
1952 CPCI405_config LANTEC_config cogent_common_config
1953 CPCIISER4_config MBX_config cogent_mpc8260_config
1954 CU824_config MBX860T_config cogent_mpc8xx_config
1955 ESTEEM192E_config RPXlite_config hermes_config
1956 ETX094_config RPXsuper_config hymod_config
1957 FADS823_config SM850_config lwmon_config
1958 FADS850SAR_config SPD823TS_config pcu_e_config
1959 FADS860T_config SXNI855T_config rsdproto_config
1960 FPS850L_config Sandpoint8240_config sbc8260_config
1961 GENIETV_config TQM823L_config PIP405_config
1962 GEN860T_config EBONY_config FPS860L_config
1963 ELPT860_config cmi_mpc5xx_config NETVIA_config
1964 at91rm9200dk_config omap1510inn_config MPC8260ADS_config
1965 omap1610inn_config ZPC1900_config MPC8540ADS_config
1968 Note: for some board special configuration names may exist; check if
1969 additional information is available from the board vendor; for
1970 instance, the TQM8xxL systems run normally at 50 MHz and use a
1971 SCC for 10baseT ethernet; there are also systems with 80 MHz
1972 CPU clock, and an optional Fast Ethernet module is available
1973 for CPU's with FEC. You can select such additional "features"
1974 when chosing the configuration, i. e.
1977 - will configure for a plain TQM860L, i. e. 50MHz, no FEC
1979 make TQM860L_FEC_config
1980 - will configure for a TQM860L at 50MHz with FEC for ethernet
1982 make TQM860L_80MHz_config
1983 - will configure for a TQM860L at 80 MHz, with normal 10baseT
1986 make TQM860L_FEC_80MHz_config
1987 - will configure for a TQM860L at 80 MHz with FEC for ethernet
1989 make TQM823L_LCD_config
1990 - will configure for a TQM823L with U-Boot console on LCD
1992 make TQM823L_LCD_80MHz_config
1993 - will configure for a TQM823L at 80 MHz with U-Boot console on LCD
1998 Finally, type "make all", and you should get some working U-Boot
1999 images ready for download to / installation on your system:
2001 - "u-boot.bin" is a raw binary image
2002 - "u-boot" is an image in ELF binary format
2003 - "u-boot.srec" is in Motorola S-Record format
2006 Please be aware that the Makefiles assume you are using GNU make, so
2007 for instance on NetBSD you might need to use "gmake" instead of
2011 If the system board that you have is not listed, then you will need
2012 to port U-Boot to your hardware platform. To do this, follow these
2015 1. Add a new configuration option for your board to the toplevel
2016 "Makefile" and to the "MAKEALL" script, using the existing
2017 entries as examples. Note that here and at many other places
2018 boards and other names are listed in alphabetical sort order. Please
2020 2. Create a new directory to hold your board specific code. Add any
2021 files you need. In your board directory, you will need at least
2022 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2023 3. Create a new configuration file "include/configs/<board>.h" for
2025 3. If you're porting U-Boot to a new CPU, then also create a new
2026 directory to hold your CPU specific code. Add any files you need.
2027 4. Run "make <board>_config" with your new name.
2028 5. Type "make", and you should get a working "u-boot.srec" file
2029 to be installed on your target system.
2030 6. Debug and solve any problems that might arise.
2031 [Of course, this last step is much harder than it sounds.]
2034 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2035 ==============================================================
2037 If you have modified U-Boot sources (for instance added a new board
2038 or support for new devices, a new CPU, etc.) you are expected to
2039 provide feedback to the other developers. The feedback normally takes
2040 the form of a "patch", i. e. a context diff against a certain (latest
2041 official or latest in CVS) version of U-Boot sources.
2043 But before you submit such a patch, please verify that your modifi-
2044 cation did not break existing code. At least make sure that *ALL* of
2045 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2046 just run the "MAKEALL" script, which will configure and build U-Boot
2047 for ALL supported system. Be warned, this will take a while. You can
2048 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2049 environment variable to the script, i. e. to use the cross tools from
2050 MontaVista's Hard Hat Linux you can type
2052 CROSS_COMPILE=ppc_8xx- MAKEALL
2054 or to build on a native PowerPC system you can type
2056 CROSS_COMPILE=' ' MAKEALL
2058 See also "U-Boot Porting Guide" below.
2061 Monitor Commands - Overview:
2062 ============================
2064 go - start application at address 'addr'
2065 run - run commands in an environment variable
2066 bootm - boot application image from memory
2067 bootp - boot image via network using BootP/TFTP protocol
2068 tftpboot- boot image via network using TFTP protocol
2069 and env variables "ipaddr" and "serverip"
2070 (and eventually "gatewayip")
2071 rarpboot- boot image via network using RARP/TFTP protocol
2072 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2073 loads - load S-Record file over serial line
2074 loadb - load binary file over serial line (kermit mode)
2076 mm - memory modify (auto-incrementing)
2077 nm - memory modify (constant address)
2078 mw - memory write (fill)
2080 cmp - memory compare
2081 crc32 - checksum calculation
2082 imd - i2c memory display
2083 imm - i2c memory modify (auto-incrementing)
2084 inm - i2c memory modify (constant address)
2085 imw - i2c memory write (fill)
2086 icrc32 - i2c checksum calculation
2087 iprobe - probe to discover valid I2C chip addresses
2088 iloop - infinite loop on address range
2089 isdram - print SDRAM configuration information
2090 sspi - SPI utility commands
2091 base - print or set address offset
2092 printenv- print environment variables
2093 setenv - set environment variables
2094 saveenv - save environment variables to persistent storage
2095 protect - enable or disable FLASH write protection
2096 erase - erase FLASH memory
2097 flinfo - print FLASH memory information
2098 bdinfo - print Board Info structure
2099 iminfo - print header information for application image
2100 coninfo - print console devices and informations
2101 ide - IDE sub-system
2102 loop - infinite loop on address range
2103 mtest - simple RAM test
2104 icache - enable or disable instruction cache
2105 dcache - enable or disable data cache
2106 reset - Perform RESET of the CPU
2107 echo - echo args to console
2108 version - print monitor version
2109 help - print online help
2110 ? - alias for 'help'
2113 Monitor Commands - Detailed Description:
2114 ========================================
2118 For now: just type "help <command>".
2121 Environment Variables:
2122 ======================
2124 U-Boot supports user configuration using Environment Variables which
2125 can be made persistent by saving to Flash memory.
2127 Environment Variables are set using "setenv", printed using
2128 "printenv", and saved to Flash using "saveenv". Using "setenv"
2129 without a value can be used to delete a variable from the
2130 environment. As long as you don't save the environment you are
2131 working with an in-memory copy. In case the Flash area containing the
2132 environment is erased by accident, a default environment is provided.
2134 Some configuration options can be set using Environment Variables:
2136 baudrate - see CONFIG_BAUDRATE
2138 bootdelay - see CONFIG_BOOTDELAY
2140 bootcmd - see CONFIG_BOOTCOMMAND
2142 bootargs - Boot arguments when booting an RTOS image
2144 bootfile - Name of the image to load with TFTP
2146 autoload - if set to "no" (any string beginning with 'n'),
2147 "bootp" will just load perform a lookup of the
2148 configuration from the BOOTP server, but not try to
2149 load any image using TFTP
2151 autostart - if set to "yes", an image loaded using the "bootp",
2152 "rarpboot", "tftpboot" or "diskboot" commands will
2153 be automatically started (by internally calling
2156 If set to "no", a standalone image passed to the
2157 "bootm" command will be copied to the load address
2158 (and eventually uncompressed), but NOT be started.
2159 This can be used to load and uncompress arbitrary
2162 initrd_high - restrict positioning of initrd images:
2163 If this variable is not set, initrd images will be
2164 copied to the highest possible address in RAM; this
2165 is usually what you want since it allows for
2166 maximum initrd size. If for some reason you want to
2167 make sure that the initrd image is loaded below the
2168 CFG_BOOTMAPSZ limit, you can set this environment
2169 variable to a value of "no" or "off" or "0".
2170 Alternatively, you can set it to a maximum upper
2171 address to use (U-Boot will still check that it
2172 does not overwrite the U-Boot stack and data).
2174 For instance, when you have a system with 16 MB
2175 RAM, and want to reserve 4 MB from use by Linux,
2176 you can do this by adding "mem=12M" to the value of
2177 the "bootargs" variable. However, now you must make
2178 sure that the initrd image is placed in the first
2179 12 MB as well - this can be done with
2181 setenv initrd_high 00c00000
2183 If you set initrd_high to 0xFFFFFFFF, this is an
2184 indication to U-Boot that all addresses are legal
2185 for the Linux kernel, including addresses in flash
2186 memory. In this case U-Boot will NOT COPY the
2187 ramdisk at all. This may be useful to reduce the
2188 boot time on your system, but requires that this
2189 feature is supported by your Linux kernel.
2191 ipaddr - IP address; needed for tftpboot command
2193 loadaddr - Default load address for commands like "bootp",
2194 "rarpboot", "tftpboot", "loadb" or "diskboot"
2196 loads_echo - see CONFIG_LOADS_ECHO
2198 serverip - TFTP server IP address; needed for tftpboot command
2200 bootretry - see CONFIG_BOOT_RETRY_TIME
2202 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2204 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2207 The following environment variables may be used and automatically
2208 updated by the network boot commands ("bootp" and "rarpboot"),
2209 depending the information provided by your boot server:
2211 bootfile - see above
2212 dnsip - IP address of your Domain Name Server
2213 dnsip2 - IP address of your secondary Domain Name Server
2214 gatewayip - IP address of the Gateway (Router) to use
2215 hostname - Target hostname
2217 netmask - Subnet Mask
2218 rootpath - Pathname of the root filesystem on the NFS server
2219 serverip - see above
2222 There are two special Environment Variables:
2224 serial# - contains hardware identification information such
2225 as type string and/or serial number
2226 ethaddr - Ethernet address
2228 These variables can be set only once (usually during manufacturing of
2229 the board). U-Boot refuses to delete or overwrite these variables
2230 once they have been set once.
2233 Further special Environment Variables:
2235 ver - Contains the U-Boot version string as printed
2236 with the "version" command. This variable is
2237 readonly (see CONFIG_VERSION_VARIABLE).
2240 Please note that changes to some configuration parameters may take
2241 only effect after the next boot (yes, that's just like Windoze :-).
2244 Command Line Parsing:
2245 =====================
2247 There are two different command line parsers available with U-Boot:
2248 the old "simple" one, and the much more powerful "hush" shell:
2250 Old, simple command line parser:
2251 --------------------------------
2253 - supports environment variables (through setenv / saveenv commands)
2254 - several commands on one line, separated by ';'
2255 - variable substitution using "... $(name) ..." syntax
2256 - special characters ('$', ';') can be escaped by prefixing with '\',
2258 setenv bootcmd bootm \$(address)
2259 - You can also escape text by enclosing in single apostrophes, for example:
2260 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2265 - similar to Bourne shell, with control structures like
2266 if...then...else...fi, for...do...done; while...do...done,
2267 until...do...done, ...
2268 - supports environment ("global") variables (through setenv / saveenv
2269 commands) and local shell variables (through standard shell syntax
2270 "name=value"); only environment variables can be used with "run"
2276 (1) If a command line (or an environment variable executed by a "run"
2277 command) contains several commands separated by semicolon, and
2278 one of these commands fails, then the remaining commands will be
2281 (2) If you execute several variables with one call to run (i. e.
2282 calling run with a list af variables as arguments), any failing
2283 command will cause "run" to terminate, i. e. the remaining
2284 variables are not executed.
2286 Note for Redundant Ethernet Interfaces:
2287 =======================================
2289 Some boards come with redundant ethernet interfaces; U-Boot supports
2290 such configurations and is capable of automatic selection of a
2291 "working" interface when needed. MAC assignment works as follows:
2293 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2294 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2295 "eth1addr" (=>eth1), "eth2addr", ...
2297 If the network interface stores some valid MAC address (for instance
2298 in SROM), this is used as default address if there is NO correspon-
2299 ding setting in the environment; if the corresponding environment
2300 variable is set, this overrides the settings in the card; that means:
2302 o If the SROM has a valid MAC address, and there is no address in the
2303 environment, the SROM's address is used.
2305 o If there is no valid address in the SROM, and a definition in the
2306 environment exists, then the value from the environment variable is
2309 o If both the SROM and the environment contain a MAC address, and
2310 both addresses are the same, this MAC address is used.
2312 o If both the SROM and the environment contain a MAC address, and the
2313 addresses differ, the value from the environment is used and a
2316 o If neither SROM nor the environment contain a MAC address, an error
2323 The "boot" commands of this monitor operate on "image" files which
2324 can be basicly anything, preceeded by a special header; see the
2325 definitions in include/image.h for details; basicly, the header
2326 defines the following image properties:
2328 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2329 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2330 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2331 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2332 * Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2333 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2334 Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
2335 * Compression Type (uncompressed, gzip, bzip2)
2341 The header is marked by a special Magic Number, and both the header
2342 and the data portions of the image are secured against corruption by
2349 Although U-Boot should support any OS or standalone application
2350 easily, the main focus has always been on Linux during the design of
2353 U-Boot includes many features that so far have been part of some
2354 special "boot loader" code within the Linux kernel. Also, any
2355 "initrd" images to be used are no longer part of one big Linux image;
2356 instead, kernel and "initrd" are separate images. This implementation
2357 serves several purposes:
2359 - the same features can be used for other OS or standalone
2360 applications (for instance: using compressed images to reduce the
2361 Flash memory footprint)
2363 - it becomes much easier to port new Linux kernel versions because
2364 lots of low-level, hardware dependent stuff are done by U-Boot
2366 - the same Linux kernel image can now be used with different "initrd"
2367 images; of course this also means that different kernel images can
2368 be run with the same "initrd". This makes testing easier (you don't
2369 have to build a new "zImage.initrd" Linux image when you just
2370 change a file in your "initrd"). Also, a field-upgrade of the
2371 software is easier now.
2377 Porting Linux to U-Boot based systems:
2378 ---------------------------------------
2380 U-Boot cannot save you from doing all the necessary modifications to
2381 configure the Linux device drivers for use with your target hardware
2382 (no, we don't intend to provide a full virtual machine interface to
2385 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
2387 Just make sure your machine specific header file (for instance
2388 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2389 Information structure as we define in include/u-boot.h, and make
2390 sure that your definition of IMAP_ADDR uses the same value as your
2391 U-Boot configuration in CFG_IMMR.
2394 Configuring the Linux kernel:
2395 -----------------------------
2397 No specific requirements for U-Boot. Make sure you have some root
2398 device (initial ramdisk, NFS) for your target system.
2401 Building a Linux Image:
2402 -----------------------
2404 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2405 not used. If you use recent kernel source, a new build target
2406 "uImage" will exist which automatically builds an image usable by
2407 U-Boot. Most older kernels also have support for a "pImage" target,
2408 which was introduced for our predecessor project PPCBoot and uses a
2409 100% compatible format.
2418 The "uImage" build target uses a special tool (in 'tools/mkimage') to
2419 encapsulate a compressed Linux kernel image with header information,
2420 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
2422 * build a standard "vmlinux" kernel image (in ELF binary format):
2424 * convert the kernel into a raw binary image:
2426 ${CROSS_COMPILE}-objcopy -O binary \
2427 -R .note -R .comment \
2428 -S vmlinux linux.bin
2430 * compress the binary image:
2434 * package compressed binary image for U-Boot:
2436 mkimage -A ppc -O linux -T kernel -C gzip \
2437 -a 0 -e 0 -n "Linux Kernel Image" \
2438 -d linux.bin.gz uImage
2441 The "mkimage" tool can also be used to create ramdisk images for use
2442 with U-Boot, either separated from the Linux kernel image, or
2443 combined into one file. "mkimage" encapsulates the images with a 64
2444 byte header containing information about target architecture,
2445 operating system, image type, compression method, entry points, time
2446 stamp, CRC32 checksums, etc.
2448 "mkimage" can be called in two ways: to verify existing images and
2449 print the header information, or to build new images.
2451 In the first form (with "-l" option) mkimage lists the information
2452 contained in the header of an existing U-Boot image; this includes
2453 checksum verification:
2455 tools/mkimage -l image
2456 -l ==> list image header information
2458 The second form (with "-d" option) is used to build a U-Boot image
2459 from a "data file" which is used as image payload:
2461 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2462 -n name -d data_file image
2463 -A ==> set architecture to 'arch'
2464 -O ==> set operating system to 'os'
2465 -T ==> set image type to 'type'
2466 -C ==> set compression type 'comp'
2467 -a ==> set load address to 'addr' (hex)
2468 -e ==> set entry point to 'ep' (hex)
2469 -n ==> set image name to 'name'
2470 -d ==> use image data from 'datafile'
2472 Right now, all Linux kernels use the same load address (0x00000000),
2473 but the entry point address depends on the kernel version:
2475 - 2.2.x kernels have the entry point at 0x0000000C,
2476 - 2.3.x and later kernels have the entry point at 0x00000000.
2478 So a typical call to build a U-Boot image would read:
2480 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2481 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2482 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2483 > examples/uImage.TQM850L
2484 Image Name: 2.4.4 kernel for TQM850L
2485 Created: Wed Jul 19 02:34:59 2000
2486 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2487 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2488 Load Address: 0x00000000
2489 Entry Point: 0x00000000
2491 To verify the contents of the image (or check for corruption):
2493 -> tools/mkimage -l examples/uImage.TQM850L
2494 Image Name: 2.4.4 kernel for TQM850L
2495 Created: Wed Jul 19 02:34:59 2000
2496 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2497 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2498 Load Address: 0x00000000
2499 Entry Point: 0x00000000
2501 NOTE: for embedded systems where boot time is critical you can trade
2502 speed for memory and install an UNCOMPRESSED image instead: this
2503 needs more space in Flash, but boots much faster since it does not
2504 need to be uncompressed:
2506 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2507 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2508 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2509 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2510 > examples/uImage.TQM850L-uncompressed
2511 Image Name: 2.4.4 kernel for TQM850L
2512 Created: Wed Jul 19 02:34:59 2000
2513 Image Type: PowerPC Linux Kernel Image (uncompressed)
2514 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2515 Load Address: 0x00000000
2516 Entry Point: 0x00000000
2519 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2520 when your kernel is intended to use an initial ramdisk:
2522 -> tools/mkimage -n 'Simple Ramdisk Image' \
2523 > -A ppc -O linux -T ramdisk -C gzip \
2524 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2525 Image Name: Simple Ramdisk Image
2526 Created: Wed Jan 12 14:01:50 2000
2527 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2528 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2529 Load Address: 0x00000000
2530 Entry Point: 0x00000000
2533 Installing a Linux Image:
2534 -------------------------
2536 To downloading a U-Boot image over the serial (console) interface,
2537 you must convert the image to S-Record format:
2539 objcopy -I binary -O srec examples/image examples/image.srec
2541 The 'objcopy' does not understand the information in the U-Boot
2542 image header, so the resulting S-Record file will be relative to
2543 address 0x00000000. To load it to a given address, you need to
2544 specify the target address as 'offset' parameter with the 'loads'
2547 Example: install the image to address 0x40100000 (which on the
2548 TQM8xxL is in the first Flash bank):
2550 => erase 40100000 401FFFFF
2556 ## Ready for S-Record download ...
2557 ~>examples/image.srec
2558 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2560 15989 15990 15991 15992
2561 [file transfer complete]
2563 ## Start Addr = 0x00000000
2566 You can check the success of the download using the 'iminfo' command;
2567 this includes a checksum verification so you can be sure no data
2568 corruption happened:
2572 ## Checking Image at 40100000 ...
2573 Image Name: 2.2.13 for initrd on TQM850L
2574 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2575 Data Size: 335725 Bytes = 327 kB = 0 MB
2576 Load Address: 00000000
2577 Entry Point: 0000000c
2578 Verifying Checksum ... OK
2584 The "bootm" command is used to boot an application that is stored in
2585 memory (RAM or Flash). In case of a Linux kernel image, the contents
2586 of the "bootargs" environment variable is passed to the kernel as
2587 parameters. You can check and modify this variable using the
2588 "printenv" and "setenv" commands:
2591 => printenv bootargs
2592 bootargs=root=/dev/ram
2594 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2596 => printenv bootargs
2597 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2600 ## Booting Linux kernel at 40020000 ...
2601 Image Name: 2.2.13 for NFS on TQM850L
2602 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2603 Data Size: 381681 Bytes = 372 kB = 0 MB
2604 Load Address: 00000000
2605 Entry Point: 0000000c
2606 Verifying Checksum ... OK
2607 Uncompressing Kernel Image ... OK
2608 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2609 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2610 time_init: decrementer frequency = 187500000/60
2611 Calibrating delay loop... 49.77 BogoMIPS
2612 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2615 If you want to boot a Linux kernel with initial ram disk, you pass
2616 the memory addresses of both the kernel and the initrd image (PPBCOOT
2617 format!) to the "bootm" command:
2619 => imi 40100000 40200000
2621 ## Checking Image at 40100000 ...
2622 Image Name: 2.2.13 for initrd on TQM850L
2623 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2624 Data Size: 335725 Bytes = 327 kB = 0 MB
2625 Load Address: 00000000
2626 Entry Point: 0000000c
2627 Verifying Checksum ... OK
2629 ## Checking Image at 40200000 ...
2630 Image Name: Simple Ramdisk Image
2631 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2632 Data Size: 566530 Bytes = 553 kB = 0 MB
2633 Load Address: 00000000
2634 Entry Point: 00000000
2635 Verifying Checksum ... OK
2637 => bootm 40100000 40200000
2638 ## Booting Linux kernel at 40100000 ...
2639 Image Name: 2.2.13 for initrd on TQM850L
2640 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2641 Data Size: 335725 Bytes = 327 kB = 0 MB
2642 Load Address: 00000000
2643 Entry Point: 0000000c
2644 Verifying Checksum ... OK
2645 Uncompressing Kernel Image ... OK
2646 ## Loading RAMDisk Image at 40200000 ...
2647 Image Name: Simple Ramdisk Image
2648 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2649 Data Size: 566530 Bytes = 553 kB = 0 MB
2650 Load Address: 00000000
2651 Entry Point: 00000000
2652 Verifying Checksum ... OK
2653 Loading Ramdisk ... OK
2654 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2655 Boot arguments: root=/dev/ram
2656 time_init: decrementer frequency = 187500000/60
2657 Calibrating delay loop... 49.77 BogoMIPS
2659 RAMDISK: Compressed image found at block 0
2660 VFS: Mounted root (ext2 filesystem).
2664 More About U-Boot Image Types:
2665 ------------------------------
2667 U-Boot supports the following image types:
2669 "Standalone Programs" are directly runnable in the environment
2670 provided by U-Boot; it is expected that (if they behave
2671 well) you can continue to work in U-Boot after return from
2672 the Standalone Program.
2673 "OS Kernel Images" are usually images of some Embedded OS which
2674 will take over control completely. Usually these programs
2675 will install their own set of exception handlers, device
2676 drivers, set up the MMU, etc. - this means, that you cannot
2677 expect to re-enter U-Boot except by resetting the CPU.
2678 "RAMDisk Images" are more or less just data blocks, and their
2679 parameters (address, size) are passed to an OS kernel that is
2681 "Multi-File Images" contain several images, typically an OS
2682 (Linux) kernel image and one or more data images like
2683 RAMDisks. This construct is useful for instance when you want
2684 to boot over the network using BOOTP etc., where the boot
2685 server provides just a single image file, but you want to get
2686 for instance an OS kernel and a RAMDisk image.
2688 "Multi-File Images" start with a list of image sizes, each
2689 image size (in bytes) specified by an "uint32_t" in network
2690 byte order. This list is terminated by an "(uint32_t)0".
2691 Immediately after the terminating 0 follow the images, one by
2692 one, all aligned on "uint32_t" boundaries (size rounded up to
2693 a multiple of 4 bytes).
2695 "Firmware Images" are binary images containing firmware (like
2696 U-Boot or FPGA images) which usually will be programmed to
2699 "Script files" are command sequences that will be executed by
2700 U-Boot's command interpreter; this feature is especially
2701 useful when you configure U-Boot to use a real shell (hush)
2702 as command interpreter.
2708 One of the features of U-Boot is that you can dynamically load and
2709 run "standalone" applications, which can use some resources of
2710 U-Boot like console I/O functions or interrupt services.
2712 Two simple examples are included with the sources:
2717 'examples/hello_world.c' contains a small "Hello World" Demo
2718 application; it is automatically compiled when you build U-Boot.
2719 It's configured to run at address 0x00040004, so you can play with it
2723 ## Ready for S-Record download ...
2724 ~>examples/hello_world.srec
2725 1 2 3 4 5 6 7 8 9 10 11 ...
2726 [file transfer complete]
2728 ## Start Addr = 0x00040004
2730 => go 40004 Hello World! This is a test.
2731 ## Starting application at 0x00040004 ...
2742 Hit any key to exit ...
2744 ## Application terminated, rc = 0x0
2746 Another example, which demonstrates how to register a CPM interrupt
2747 handler with the U-Boot code, can be found in 'examples/timer.c'.
2748 Here, a CPM timer is set up to generate an interrupt every second.
2749 The interrupt service routine is trivial, just printing a '.'
2750 character, but this is just a demo program. The application can be
2751 controlled by the following keys:
2753 ? - print current values og the CPM Timer registers
2754 b - enable interrupts and start timer
2755 e - stop timer and disable interrupts
2756 q - quit application
2759 ## Ready for S-Record download ...
2760 ~>examples/timer.srec
2761 1 2 3 4 5 6 7 8 9 10 11 ...
2762 [file transfer complete]
2764 ## Start Addr = 0x00040004
2767 ## Starting application at 0x00040004 ...
2770 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
2773 [q, b, e, ?] Set interval 1000000 us
2776 [q, b, e, ?] ........
2777 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
2780 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
2783 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
2786 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
2788 [q, b, e, ?] ...Stopping timer
2790 [q, b, e, ?] ## Application terminated, rc = 0x0
2796 Over time, many people have reported problems when trying to use the
2797 "minicom" terminal emulation program for serial download. I (wd)
2798 consider minicom to be broken, and recommend not to use it. Under
2799 Unix, I recommend to use C-Kermit for general purpose use (and
2800 especially for kermit binary protocol download ("loadb" command), and
2801 use "cu" for S-Record download ("loads" command).
2803 Nevertheless, if you absolutely want to use it try adding this
2804 configuration to your "File transfer protocols" section:
2806 Name Program Name U/D FullScr IO-Red. Multi
2807 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
2808 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
2814 Starting at version 0.9.2, U-Boot supports NetBSD both as host
2815 (build U-Boot) and target system (boots NetBSD/mpc8xx).
2817 Building requires a cross environment; it is known to work on
2818 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
2819 need gmake since the Makefiles are not compatible with BSD make).
2820 Note that the cross-powerpc package does not install include files;
2821 attempting to build U-Boot will fail because <machine/ansi.h> is
2822 missing. This file has to be installed and patched manually:
2824 # cd /usr/pkg/cross/powerpc-netbsd/include
2826 # ln -s powerpc machine
2827 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
2828 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
2830 Native builds *don't* work due to incompatibilities between native
2831 and U-Boot include files.
2833 Booting assumes that (the first part of) the image booted is a
2834 stage-2 loader which in turn loads and then invokes the kernel
2835 proper. Loader sources will eventually appear in the NetBSD source
2836 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
2837 meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
2841 Implementation Internals:
2842 =========================
2844 The following is not intended to be a complete description of every
2845 implementation detail. However, it should help to understand the
2846 inner workings of U-Boot and make it easier to port it to custom
2850 Initial Stack, Global Data:
2851 ---------------------------
2853 The implementation of U-Boot is complicated by the fact that U-Boot
2854 starts running out of ROM (flash memory), usually without access to
2855 system RAM (because the memory controller is not initialized yet).
2856 This means that we don't have writable Data or BSS segments, and BSS
2857 is not initialized as zero. To be able to get a C environment working
2858 at all, we have to allocate at least a minimal stack. Implementation
2859 options for this are defined and restricted by the CPU used: Some CPU
2860 models provide on-chip memory (like the IMMR area on MPC8xx and
2861 MPC826x processors), on others (parts of) the data cache can be
2862 locked as (mis-) used as memory, etc.
2864 Chris Hallinan posted a good summary of these issues to the
2865 u-boot-users mailing list:
2867 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
2868 From: "Chris Hallinan" <clh@net1plus.com>
2869 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
2872 Correct me if I'm wrong, folks, but the way I understand it
2873 is this: Using DCACHE as initial RAM for Stack, etc, does not
2874 require any physical RAM backing up the cache. The cleverness
2875 is that the cache is being used as a temporary supply of
2876 necessary storage before the SDRAM controller is setup. It's
2877 beyond the scope of this list to expain the details, but you
2878 can see how this works by studying the cache architecture and
2879 operation in the architecture and processor-specific manuals.
2881 OCM is On Chip Memory, which I believe the 405GP has 4K. It
2882 is another option for the system designer to use as an
2883 initial stack/ram area prior to SDRAM being available. Either
2884 option should work for you. Using CS 4 should be fine if your
2885 board designers haven't used it for something that would
2886 cause you grief during the initial boot! It is frequently not
2889 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
2890 with your processor/board/system design. The default value
2891 you will find in any recent u-boot distribution in
2892 Walnut405.h should work for you. I'd set it to a value larger
2893 than your SDRAM module. If you have a 64MB SDRAM module, set
2894 it above 400_0000. Just make sure your board has no resources
2895 that are supposed to respond to that address! That code in
2896 start.S has been around a while and should work as is when
2897 you get the config right.
2902 It is essential to remember this, since it has some impact on the C
2903 code for the initialization procedures:
2905 * Initialized global data (data segment) is read-only. Do not attempt
2908 * Do not use any unitialized global data (or implicitely initialized
2909 as zero data - BSS segment) at all - this is undefined, initiali-
2910 zation is performed later (when relocating to RAM).
2912 * Stack space is very limited. Avoid big data buffers or things like
2915 Having only the stack as writable memory limits means we cannot use
2916 normal global data to share information beween the code. But it
2917 turned out that the implementation of U-Boot can be greatly
2918 simplified by making a global data structure (gd_t) available to all
2919 functions. We could pass a pointer to this data as argument to _all_
2920 functions, but this would bloat the code. Instead we use a feature of
2921 the GCC compiler (Global Register Variables) to share the data: we
2922 place a pointer (gd) to the global data into a register which we
2923 reserve for this purpose.
2925 When choosing a register for such a purpose we are restricted by the
2926 relevant (E)ABI specifications for the current architecture, and by
2927 GCC's implementation.
2929 For PowerPC, the following registers have specific use:
2932 R3-R4: parameter passing and return values
2933 R5-R10: parameter passing
2934 R13: small data area pointer
2938 (U-Boot also uses R14 as internal GOT pointer.)
2940 ==> U-Boot will use R29 to hold a pointer to the global data
2942 Note: on PPC, we could use a static initializer (since the
2943 address of the global data structure is known at compile time),
2944 but it turned out that reserving a register results in somewhat
2945 smaller code - although the code savings are not that big (on
2946 average for all boards 752 bytes for the whole U-Boot image,
2947 624 text + 127 data).
2949 On ARM, the following registers are used:
2951 R0: function argument word/integer result
2952 R1-R3: function argument word
2954 R10: stack limit (used only if stack checking if enabled)
2955 R11: argument (frame) pointer
2956 R12: temporary workspace
2959 R15: program counter
2961 ==> U-Boot will use R8 to hold a pointer to the global data
2967 U-Boot runs in system state and uses physical addresses, i.e. the
2968 MMU is not used either for address mapping nor for memory protection.
2970 The available memory is mapped to fixed addresses using the memory
2971 controller. In this process, a contiguous block is formed for each
2972 memory type (Flash, SDRAM, SRAM), even when it consists of several
2973 physical memory banks.
2975 U-Boot is installed in the first 128 kB of the first Flash bank (on
2976 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
2977 booting and sizing and initializing DRAM, the code relocates itself
2978 to the upper end of DRAM. Immediately below the U-Boot code some
2979 memory is reserved for use by malloc() [see CFG_MALLOC_LEN
2980 configuration setting]. Below that, a structure with global Board
2981 Info data is placed, followed by the stack (growing downward).
2983 Additionally, some exception handler code is copied to the low 8 kB
2984 of DRAM (0x00000000 ... 0x00001FFF).
2986 So a typical memory configuration with 16 MB of DRAM could look like
2989 0x0000 0000 Exception Vector code
2992 0x0000 2000 Free for Application Use
2998 0x00FB FF20 Monitor Stack (Growing downward)
2999 0x00FB FFAC Board Info Data and permanent copy of global data
3000 0x00FC 0000 Malloc Arena
3003 0x00FE 0000 RAM Copy of Monitor Code
3004 ... eventually: LCD or video framebuffer
3005 ... eventually: pRAM (Protected RAM - unchanged by reset)
3006 0x00FF FFFF [End of RAM]
3009 System Initialization:
3010 ----------------------
3012 In the reset configuration, U-Boot starts at the reset entry point
3013 (on most PowerPC systens at address 0x00000100). Because of the reset
3014 configuration for CS0# this is a mirror of the onboard Flash memory.
3015 To be able to re-map memory U-Boot then jumps to its link address.
3016 To be able to implement the initialization code in C, a (small!)
3017 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3018 which provide such a feature like MPC8xx or MPC8260), or in a locked
3019 part of the data cache. After that, U-Boot initializes the CPU core,
3020 the caches and the SIU.
3022 Next, all (potentially) available memory banks are mapped using a
3023 preliminary mapping. For example, we put them on 512 MB boundaries
3024 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3025 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3026 programmed for SDRAM access. Using the temporary configuration, a
3027 simple memory test is run that determines the size of the SDRAM
3030 When there is more than one SDRAM bank, and the banks are of
3031 different size, the largest is mapped first. For equal size, the first
3032 bank (CS2#) is mapped first. The first mapping is always for address
3033 0x00000000, with any additional banks following immediately to create
3034 contiguous memory starting from 0.
3036 Then, the monitor installs itself at the upper end of the SDRAM area
3037 and allocates memory for use by malloc() and for the global Board
3038 Info data; also, the exception vector code is copied to the low RAM
3039 pages, and the final stack is set up.
3041 Only after this relocation will you have a "normal" C environment;
3042 until that you are restricted in several ways, mostly because you are
3043 running from ROM, and because the code will have to be relocated to a
3047 U-Boot Porting Guide:
3048 ----------------------
3050 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3054 int main (int argc, char *argv[])
3056 sighandler_t no_more_time;
3058 signal (SIGALRM, no_more_time);
3059 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3061 if (available_money > available_manpower) {
3062 pay consultant to port U-Boot;
3066 Download latest U-Boot source;
3068 Subscribe to u-boot-users mailing list;
3071 email ("Hi, I am new to U-Boot, how do I get started?");
3075 Read the README file in the top level directory;
3076 Read http://www.denx.de/re/DPLG.html
3077 Read the source, Luke;
3080 if (available_money > toLocalCurrency ($2500)) {
3083 Add a lot of aggravation and time;
3086 Create your own board support subdirectory;
3088 Create your own board config file;
3092 Add / modify source code;
3096 email ("Hi, I am having problems...");
3098 Send patch file to Wolfgang;
3103 void no_more_time (int sig)
3112 All contributions to U-Boot should conform to the Linux kernel
3113 coding style; see the file "Documentation/CodingStyle" in your Linux
3114 kernel source directory.
3116 Please note that U-Boot is implemented in C (and to some small parts
3117 in Assembler); no C++ is used, so please do not use C++ style
3118 comments (//) in your code.
3120 Submissions which do not conform to the standards may be returned
3121 with a request to reformat the changes.
3127 Since the number of patches for U-Boot is growing, we need to
3128 establish some rules. Submissions which do not conform to these rules
3129 may be rejected, even when they contain important and valuable stuff.
3132 When you send a patch, please include the following information with
3135 * For bug fixes: a description of the bug and how your patch fixes
3136 this bug. Please try to include a way of demonstrating that the
3137 patch actually fixes something.
3139 * For new features: a description of the feature and your
3142 * A CHANGELOG entry as plaintext (separate from the patch)
3144 * For major contributions, your entry to the CREDITS file
3146 * When you add support for a new board, don't forget to add this
3147 board to the MAKEALL script, too.
3149 * If your patch adds new configuration options, don't forget to
3150 document these in the README file.
3152 * The patch itself. If you are accessing the CVS repository use "cvs
3153 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3154 version of diff does not support these options, then get the latest
3155 version of GNU diff.
3157 The current directory when running this command shall be the top
3158 level directory of the U-Boot source tree, or it's parent directory
3159 (i. e. please make sure that your patch includes sufficient
3160 directory information for the affected files).
3162 We accept patches as plain text, MIME attachments or as uuencoded
3165 * If one logical set of modifications affects or creates several
3166 files, all these changes shall be submitted in a SINGLE patch file.
3168 * Changesets that contain different, unrelated modifications shall be
3169 submitted as SEPARATE patches, one patch per changeset.
3174 * Before sending the patch, run the MAKEALL script on your patched
3175 source tree and make sure that no errors or warnings are reported
3176 for any of the boards.
3178 * Keep your modifications to the necessary minimum: A patch
3179 containing several unrelated changes or arbitrary reformats will be
3180 returned with a request to re-formatting / split it.
3182 * If you modify existing code, make sure that your new code does not
3183 add to the memory footprint of the code ;-) Small is beautiful!
3184 When adding new features, these should compile conditionally only
3185 (using #ifdef), and the resulting code with the new feature
3186 disabled must not need more memory than the old code without your