2 # (C) Copyright 2000 - 2004
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC and ARM processors, which can be
29 installed in a boot ROM and used to initialize and test the hardware
30 or to download and run application code.
32 The development of U-Boot is closely related to Linux: some parts of
33 the source code originate in the Linux source tree, we have some
34 header files in common, and special provision has been made to
35 support booting of Linux images.
37 Some attention has been paid to make this software easily
38 configurable and extendable. For instance, all monitor commands are
39 implemented with the same call interface, so that it's very easy to
40 add new commands. Also, instead of permanently adding rarely used
41 code (for instance hardware test utilities) to the monitor, you can
42 load and run it dynamically.
48 In general, all boards for which a configuration option exists in the
49 Makefile have been tested to some extent and can be considered
50 "working". In fact, many of them are used in production systems.
52 In case of problems see the CHANGELOG and CREDITS files to find out
53 who contributed the specific port.
59 In case you have questions about, problems with or contributions for
60 U-Boot you should send a message to the U-Boot mailing list at
61 <u-boot-users@lists.sourceforge.net>. There is also an archive of
62 previous traffic on the mailing list - please search the archive
63 before asking FAQ's. Please see
64 http://lists.sourceforge.net/lists/listinfo/u-boot-users/
70 - start from 8xxrom sources
71 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
73 - make it easier to add custom boards
74 - make it possible to add other [PowerPC] CPUs
75 - extend functions, especially:
76 * Provide extended interface to Linux boot loader
79 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
80 - create ARMBoot project (http://sourceforge.net/projects/armboot)
81 - add other CPU families (starting with ARM)
82 - create U-Boot project (http://sourceforge.net/projects/u-boot)
88 The "official" name of this project is "Das U-Boot". The spelling
89 "U-Boot" shall be used in all written text (documentation, comments
90 in source files etc.). Example:
92 This is the README file for the U-Boot project.
94 File names etc. shall be based on the string "u-boot". Examples:
96 include/asm-ppc/u-boot.h
98 #include <asm/u-boot.h>
100 Variable names, preprocessor constants etc. shall be either based on
101 the string "u_boot" or on "U_BOOT". Example:
103 U_BOOT_VERSION u_boot_logo
104 IH_OS_U_BOOT u_boot_hush_start
110 U-Boot uses a 3 level version number containing a version, a
111 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
112 sub-version "34", and patchlevel "4".
114 The patchlevel is used to indicate certain stages of development
115 between released versions, i. e. officially released versions of
116 U-Boot will always have a patchlevel of "0".
122 - board Board dependent files
123 - common Misc architecture independent functions
124 - cpu CPU specific files
125 - 74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
126 - arm720t Files specific to ARM 720 CPUs
127 - arm920t Files specific to ARM 920 CPUs
128 - arm925t Files specific to ARM 925 CPUs
129 - arm926ejs Files specific to ARM 926 CPUs
130 - at91rm9200 Files specific to Atmel AT91RM9200 CPUs
131 - i386 Files specific to i386 CPUs
132 - ixp Files specific to Intel XScale IXP CPUs
133 - mcf52x2 Files specific to Motorola ColdFire MCF52x2 CPUs
134 - mips Files specific to MIPS CPUs
135 - mpc5xx Files specific to Motorola MPC5xx CPUs
136 - mpc5xxx Files specific to Motorola MPC5xxx CPUs
137 - mpc8xx Files specific to Motorola MPC8xx CPUs
138 - mpc824x Files specific to Motorola MPC824x CPUs
139 - mpc8260 Files specific to Motorola MPC8260 CPUs
140 - mpc85xx Files specific to Motorola MPC85xx CPUs
141 - nios Files specific to Altera NIOS CPUs
142 - ppc4xx Files specific to IBM PowerPC 4xx CPUs
143 - pxa Files specific to Intel XScale PXA CPUs
144 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
145 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
146 - disk Code for disk drive partition handling
147 - doc Documentation (don't expect too much)
148 - drivers Commonly used device drivers
149 - dtt Digital Thermometer and Thermostat drivers
150 - examples Example code for standalone applications, etc.
151 - include Header Files
152 - lib_arm Files generic to ARM architecture
153 - lib_generic Files generic to all architectures
154 - lib_i386 Files generic to i386 architecture
155 - lib_m68k Files generic to m68k architecture
156 - lib_mips Files generic to MIPS architecture
157 - lib_nios Files generic to NIOS architecture
158 - lib_ppc Files generic to PowerPC architecture
159 - net Networking code
160 - post Power On Self Test
161 - rtc Real Time Clock drivers
162 - tools Tools to build S-Record or U-Boot images, etc.
164 Software Configuration:
165 =======================
167 Configuration is usually done using C preprocessor defines; the
168 rationale behind that is to avoid dead code whenever possible.
170 There are two classes of configuration variables:
172 * Configuration _OPTIONS_:
173 These are selectable by the user and have names beginning with
176 * Configuration _SETTINGS_:
177 These depend on the hardware etc. and should not be meddled with if
178 you don't know what you're doing; they have names beginning with
181 Later we will add a configuration tool - probably similar to or even
182 identical to what's used for the Linux kernel. Right now, we have to
183 do the configuration by hand, which means creating some symbolic
184 links and editing some configuration files. We use the TQM8xxL boards
188 Selection of Processor Architecture and Board Type:
189 ---------------------------------------------------
191 For all supported boards there are ready-to-use default
192 configurations available; just type "make <board_name>_config".
194 Example: For a TQM823L module type:
199 For the Cogent platform, you need to specify the cpu type as well;
200 e.g. "make cogent_mpc8xx_config". And also configure the cogent
201 directory according to the instructions in cogent/README.
204 Configuration Options:
205 ----------------------
207 Configuration depends on the combination of board and CPU type; all
208 such information is kept in a configuration file
209 "include/configs/<board_name>.h".
211 Example: For a TQM823L module, all configuration settings are in
212 "include/configs/TQM823L.h".
215 Many of the options are named exactly as the corresponding Linux
216 kernel configuration options. The intention is to make it easier to
217 build a config tool - later.
220 The following options need to be configured:
222 - CPU Type: Define exactly one of
226 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
228 or CONFIG_MPC824X, CONFIG_MPC8260
243 MicroBlaze based CPUs:
244 ----------------------
248 - Board Type: Define exactly one of
250 PowerPC based boards:
251 ---------------------
253 CONFIG_ADCIOP CONFIG_GEN860T CONFIG_PCI405
254 CONFIG_ADS860 CONFIG_GENIETV CONFIG_PCIPPC2
255 CONFIG_AMX860 CONFIG_GTH CONFIG_PCIPPC6
256 CONFIG_AR405 CONFIG_gw8260 CONFIG_pcu_e
257 CONFIG_BAB7xx CONFIG_hermes CONFIG_PIP405
258 CONFIG_c2mon CONFIG_hymod CONFIG_PM826
259 CONFIG_CANBT CONFIG_IAD210 CONFIG_ppmc8260
260 CONFIG_CCM CONFIG_ICU862 CONFIG_QS823
261 CONFIG_CMI CONFIG_IP860 CONFIG_QS850
262 CONFIG_cogent_mpc8260 CONFIG_IPHASE4539 CONFIG_QS860T
263 CONFIG_cogent_mpc8xx CONFIG_IVML24 CONFIG_RBC823
264 CONFIG_CPCI405 CONFIG_IVML24_128 CONFIG_RPXClassic
265 CONFIG_CPCI4052 CONFIG_IVML24_256 CONFIG_RPXlite
266 CONFIG_CPCIISER4 CONFIG_IVMS8 CONFIG_RPXsuper
267 CONFIG_CPU86 CONFIG_IVMS8_128 CONFIG_rsdproto
268 CONFIG_CRAYL1 CONFIG_IVMS8_256 CONFIG_sacsng
269 CONFIG_CSB272 CONFIG_JSE CONFIG_Sandpoint8240
270 CONFIG_CU824 CONFIG_LANTEC CONFIG_Sandpoint8245
271 CONFIG_DASA_SIM CONFIG_lwmon CONFIG_sbc8260
272 CONFIG_DB64360 CONFIG_MBX CONFIG_sbc8560
273 CONFIG_DB64460 CONFIG_MBX860T CONFIG_SM850
274 CONFIG_DU405 CONFIG_MHPC CONFIG_SPD823TS
275 CONFIG_DUET_ADS CONFIG_MIP405 CONFIG_STXGP3
276 CONFIG_EBONY CONFIG_MOUSSE CONFIG_SXNI855T
277 CONFIG_ELPPC CONFIG_MPC8260ADS CONFIG_TQM823L
278 CONFIG_ELPT860 CONFIG_MPC8540ADS CONFIG_TQM8260
279 CONFIG_ep8260 CONFIG_MPC8560ADS CONFIG_TQM850L
280 CONFIG_ERIC CONFIG_MUSENKI CONFIG_TQM855L
281 CONFIG_ESTEEM192E CONFIG_MVS1 CONFIG_TQM860L
282 CONFIG_ETX094 CONFIG_NETPHONE CONFIG_TTTech
283 CONFIG_EVB64260 CONFIG_NETTA CONFIG_UTX8245
284 CONFIG_FADS823 CONFIG_NETVIA CONFIG_V37
285 CONFIG_FADS850SAR CONFIG_NX823 CONFIG_W7OLMC
286 CONFIG_FADS860T CONFIG_OCRTC CONFIG_W7OLMG
287 CONFIG_FLAGADM CONFIG_ORSG CONFIG_WALNUT405
288 CONFIG_FPS850L CONFIG_OXC CONFIG_ZPC1900
289 CONFIG_FPS860L CONFIG_ZUMA
294 CONFIG_AT91RM9200DK, CONFIG_CERF250, CONFIG_DNP1110,
295 CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
296 CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
297 CONFIG_LART, CONFIG_LPD7A400 CONFIG_LUBBOCK,
298 CONFIG_OSK_OMAP5912, CONFIG_SHANNON, CONFIG_P2_OMAP730,
299 CONFIG_SMDK2400, CONFIG_SMDK2410, CONFIG_TRAB,
302 MicroBlaze based boards:
303 ------------------------
308 - CPU Module Type: (if CONFIG_COGENT is defined)
309 Define exactly one of
311 --- FIXME --- not tested yet:
312 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
313 CONFIG_CMA287_23, CONFIG_CMA287_50
315 - Motherboard Type: (if CONFIG_COGENT is defined)
316 Define exactly one of
317 CONFIG_CMA101, CONFIG_CMA102
319 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
320 Define one or more of
323 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
324 Define one or more of
325 CONFIG_LCD_HEARTBEAT - update a character position on
326 the lcd display every second with
329 - Board flavour: (if CONFIG_MPC8260ADS is defined)
332 CFG_8260ADS - original MPC8260ADS
333 CFG_8266ADS - MPC8266ADS
334 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
335 CFG_8272ADS - MPC8272ADS
337 - MPC824X Family Member (if CONFIG_MPC824X is defined)
338 Define exactly one of
339 CONFIG_MPC8240, CONFIG_MPC8245
341 - 8xx CPU Options: (if using an MPC8xx cpu)
342 Define one or more of
343 CONFIG_8xx_GCLK_FREQ - if get_gclk_freq() cannot work
344 e.g. if there is no 32KHz
345 reference PIT/RTC clock
347 - 859/866 CPU options: (if using a MPC859 or MPC866 CPU):
351 CFG_866_CPUCLK_DEFAULT
352 See doc/README.MPC866
356 Define this to measure the actual CPU clock instead
357 of relying on the correctness of the configured
358 values. Mostly useful for board bringup to make sure
359 the PLL is locked at the intended frequency. Note
360 that this requires a (stable) reference clock (32 kHz
363 - Linux Kernel Interface:
366 U-Boot stores all clock information in Hz
367 internally. For binary compatibility with older Linux
368 kernels (which expect the clocks passed in the
369 bd_info data to be in MHz) the environment variable
370 "clocks_in_mhz" can be defined so that U-Boot
371 converts clock data to MHZ before passing it to the
373 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
374 "clocks_in_mhz=1" is automatically included in the
377 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
379 When transfering memsize parameter to linux, some versions
380 expect it to be in bytes, others in MB.
381 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
386 Define this if you want support for Amba PrimeCell PL010 UARTs.
390 Define this if you want support for Amba PrimeCell PL011 UARTs.
394 If you have Amba PrimeCell PL011 UARTs, set this variable to
395 the clock speed of the UARTs.
399 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
400 define this to a list of base addresses for each (supported)
401 port. See e.g. include/configs/versatile.h
405 Depending on board, define exactly one serial port
406 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
407 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
408 console by defining CONFIG_8xx_CONS_NONE
410 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
411 port routines must be defined elsewhere
412 (i.e. serial_init(), serial_getc(), ...)
415 Enables console device for a color framebuffer. Needs following
416 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
417 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
419 VIDEO_HW_RECTFILL graphic chip supports
422 VIDEO_HW_BITBLT graphic chip supports
423 bit-blit (cf. smiLynxEM)
424 VIDEO_VISIBLE_COLS visible pixel columns
426 VIDEO_VISIBLE_ROWS visible pixel rows
427 VIDEO_PIXEL_SIZE bytes per pixel
428 VIDEO_DATA_FORMAT graphic data format
429 (0-5, cf. cfb_console.c)
430 VIDEO_FB_ADRS framebuffer address
431 VIDEO_KBD_INIT_FCT keyboard int fct
432 (i.e. i8042_kbd_init())
433 VIDEO_TSTC_FCT test char fct
435 VIDEO_GETC_FCT get char fct
437 CONFIG_CONSOLE_CURSOR cursor drawing on/off
438 (requires blink timer
440 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
441 CONFIG_CONSOLE_TIME display time/date info in
443 (requires CFG_CMD_DATE)
444 CONFIG_VIDEO_LOGO display Linux logo in
446 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
447 linux_logo.h for logo.
448 Requires CONFIG_VIDEO_LOGO
449 CONFIG_CONSOLE_EXTRA_INFO
450 addional board info beside
453 When CONFIG_CFB_CONSOLE is defined, video console is
454 default i/o. Serial console can be forced with
455 environment 'console=serial'.
457 When CONFIG_SILENT_CONSOLE is defined, all console
458 messages (by U-Boot and Linux!) can be silenced with
459 the "silent" environment variable. See
460 doc/README.silent for more information.
463 CONFIG_BAUDRATE - in bps
464 Select one of the baudrates listed in
465 CFG_BAUDRATE_TABLE, see below.
466 CFG_BRGCLK_PRESCALE, baudrate prescale
468 - Interrupt driven serial port input:
469 CONFIG_SERIAL_SOFTWARE_FIFO
472 Use an interrupt handler for receiving data on the
473 serial port. It also enables using hardware handshake
474 (RTS/CTS) and UART's built-in FIFO. Set the number of
475 bytes the interrupt driven input buffer should have.
477 Leave undefined to disable this feature, including
478 disable the buffer and hardware handshake.
480 - Console UART Number:
484 If defined internal UART1 (and not UART0) is used
485 as default U-Boot console.
487 - Boot Delay: CONFIG_BOOTDELAY - in seconds
488 Delay before automatically booting the default image;
489 set to -1 to disable autoboot.
491 See doc/README.autoboot for these options that
492 work with CONFIG_BOOTDELAY. None are required.
493 CONFIG_BOOT_RETRY_TIME
494 CONFIG_BOOT_RETRY_MIN
495 CONFIG_AUTOBOOT_KEYED
496 CONFIG_AUTOBOOT_PROMPT
497 CONFIG_AUTOBOOT_DELAY_STR
498 CONFIG_AUTOBOOT_STOP_STR
499 CONFIG_AUTOBOOT_DELAY_STR2
500 CONFIG_AUTOBOOT_STOP_STR2
501 CONFIG_ZERO_BOOTDELAY_CHECK
502 CONFIG_RESET_TO_RETRY
506 Only needed when CONFIG_BOOTDELAY is enabled;
507 define a command string that is automatically executed
508 when no character is read on the console interface
509 within "Boot Delay" after reset.
512 This can be used to pass arguments to the bootm
513 command. The value of CONFIG_BOOTARGS goes into the
514 environment value "bootargs".
516 CONFIG_RAMBOOT and CONFIG_NFSBOOT
517 The value of these goes into the environment as
518 "ramboot" and "nfsboot" respectively, and can be used
519 as a convenience, when switching between booting from
525 When this option is #defined, the existence of the
526 environment variable "preboot" will be checked
527 immediately before starting the CONFIG_BOOTDELAY
528 countdown and/or running the auto-boot command resp.
529 entering interactive mode.
531 This feature is especially useful when "preboot" is
532 automatically generated or modified. For an example
533 see the LWMON board specific code: here "preboot" is
534 modified when the user holds down a certain
535 combination of keys on the (special) keyboard when
538 - Serial Download Echo Mode:
540 If defined to 1, all characters received during a
541 serial download (using the "loads" command) are
542 echoed back. This might be needed by some terminal
543 emulations (like "cu"), but may as well just take
544 time on others. This setting #define's the initial
545 value of the "loads_echo" environment variable.
547 - Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
549 Select one of the baudrates listed in
550 CFG_BAUDRATE_TABLE, see below.
554 Most monitor functions can be selected (or
555 de-selected) by adjusting the definition of
556 CONFIG_COMMANDS; to select individual functions,
557 #define CONFIG_COMMANDS by "OR"ing any of the
560 #define enables commands:
561 -------------------------
562 CFG_CMD_ASKENV * ask for env variable
563 CFG_CMD_AUTOSCRIPT Autoscript Support
565 CFG_CMD_BEDBUG * Include BedBug Debugger
566 CFG_CMD_BMP * BMP support
567 CFG_CMD_BSP * Board specific commands
569 CFG_CMD_CACHE * icache, dcache
570 CFG_CMD_CONSOLE coninfo
571 CFG_CMD_DATE * support for RTC, date/time...
572 CFG_CMD_DHCP * DHCP support
573 CFG_CMD_DIAG * Diagnostics
574 CFG_CMD_DOC * Disk-On-Chip Support
575 CFG_CMD_DTT * Digital Therm and Thermostat
576 CFG_CMD_ECHO * echo arguments
577 CFG_CMD_EEPROM * EEPROM read/write support
578 CFG_CMD_ELF * bootelf, bootvx
580 CFG_CMD_FDC * Floppy Disk Support
581 CFG_CMD_FAT * FAT partition support
582 CFG_CMD_FDOS * Dos diskette Support
583 CFG_CMD_FLASH flinfo, erase, protect
584 CFG_CMD_FPGA FPGA device initialization support
585 CFG_CMD_HWFLOW * RTS/CTS hw flow control
586 CFG_CMD_I2C * I2C serial bus support
587 CFG_CMD_IDE * IDE harddisk support
589 CFG_CMD_IMLS List all found images
590 CFG_CMD_IMMAP * IMMR dump support
591 CFG_CMD_IRQ * irqinfo
592 CFG_CMD_ITEST Integer/string test of 2 values
593 CFG_CMD_JFFS2 * JFFS2 Support
597 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
599 CFG_CMD_MISC Misc functions like sleep etc
600 CFG_CMD_MMC * MMC memory mapped support
601 CFG_CMD_MII * MII utility commands
602 CFG_CMD_NAND * NAND support
603 CFG_CMD_NET bootp, tftpboot, rarpboot
604 CFG_CMD_PCI * pciinfo
605 CFG_CMD_PCMCIA * PCMCIA support
606 CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
607 CFG_CMD_PORTIO * Port I/O
608 CFG_CMD_REGINFO * Register dump
609 CFG_CMD_RUN run command in env variable
610 CFG_CMD_SAVES * save S record dump
611 CFG_CMD_SCSI * SCSI Support
612 CFG_CMD_SDRAM * print SDRAM configuration information
613 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
614 CFG_CMD_SPI * SPI serial bus support
615 CFG_CMD_USB * USB support
616 CFG_CMD_VFD * VFD support (TRAB)
617 CFG_CMD_BSP * Board SPecific functions
618 CFG_CMD_CDP * Cisco Discover Protocol support
619 -----------------------------------------------
622 CONFIG_CMD_DFL Default configuration; at the moment
623 this is includes all commands, except
624 the ones marked with "*" in the list
627 If you don't define CONFIG_COMMANDS it defaults to
628 CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
629 override the default settings in the respective
632 EXAMPLE: If you want all functions except of network
633 support you can write:
635 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
638 Note: Don't enable the "icache" and "dcache" commands
639 (configuration option CFG_CMD_CACHE) unless you know
640 what you (and your U-Boot users) are doing. Data
641 cache cannot be enabled on systems like the 8xx or
642 8260 (where accesses to the IMMR region must be
643 uncached), and it cannot be disabled on all other
644 systems where we (mis-) use the data cache to hold an
645 initial stack and some data.
648 XXX - this list needs to get updated!
652 If this variable is defined, it enables watchdog
653 support. There must be support in the platform specific
654 code for a watchdog. For the 8xx and 8260 CPUs, the
655 SIU Watchdog feature is enabled in the SYPCR
659 CONFIG_VERSION_VARIABLE
660 If this variable is defined, an environment variable
661 named "ver" is created by U-Boot showing the U-Boot
662 version as printed by the "version" command.
663 This variable is readonly.
667 When CFG_CMD_DATE is selected, the type of the RTC
668 has to be selected, too. Define exactly one of the
671 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
672 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
673 CONFIG_RTC_MC146818 - use MC146818 RTC
674 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
675 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
676 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
677 CONFIG_RTC_DS164x - use Dallas DS164x RTC
678 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
680 Note that if the RTC uses I2C, then the I2C interface
681 must also be configured. See I2C Support, below.
685 When CONFIG_TIMESTAMP is selected, the timestamp
686 (date and time) of an image is printed by image
687 commands like bootm or iminfo. This option is
688 automatically enabled when you select CFG_CMD_DATE .
691 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
692 and/or CONFIG_ISO_PARTITION
694 If IDE or SCSI support is enabled (CFG_CMD_IDE or
695 CFG_CMD_SCSI) you must configure support for at least
696 one partition type as well.
699 CONFIG_IDE_RESET_ROUTINE - this is defined in several
700 board configurations files but used nowhere!
702 CONFIG_IDE_RESET - is this is defined, IDE Reset will
703 be performed by calling the function
704 ide_set_reset(int reset)
705 which has to be defined in a board specific file
710 Set this to enable ATAPI support.
715 Set this to enable support for disks larger than 137GB
716 Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
717 Whithout these , LBA48 support uses 32bit variables and will 'only'
718 support disks up to 2.1TB.
721 When enabled, makes the IDE subsystem use 64bit sector addresses.
725 At the moment only there is only support for the
726 SYM53C8XX SCSI controller; define
727 CONFIG_SCSI_SYM53C8XX to enable it.
729 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
730 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
731 CFG_SCSI_MAX_LUN] can be adjusted to define the
732 maximum numbers of LUNs, SCSI ID's and target
734 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
736 - NETWORK Support (PCI):
738 Support for Intel 8254x gigabit chips.
741 Support for Intel 82557/82559/82559ER chips.
742 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
743 write routine for first time initialisation.
746 Support for Digital 2114x chips.
747 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
748 modem chip initialisation (KS8761/QS6611).
751 Support for National dp83815 chips.
754 Support for National dp8382[01] gigabit chips.
756 - NETWORK Support (other):
758 CONFIG_DRIVER_LAN91C96
759 Support for SMSC's LAN91C96 chips.
762 Define this to hold the physical address
763 of the LAN91C96's I/O space
765 CONFIG_LAN91C96_USE_32_BIT
766 Define this to enable 32 bit addressing
768 CONFIG_DRIVER_SMC91111
769 Support for SMSC's LAN91C111 chip
772 Define this to hold the physical address
773 of the device (I/O space)
775 CONFIG_SMC_USE_32_BIT
776 Define this if data bus is 32 bits
778 CONFIG_SMC_USE_IOFUNCS
779 Define this to use i/o functions instead of macros
780 (some hardware wont work with macros)
783 At the moment only the UHCI host controller is
784 supported (PIP405, MIP405, MPC5200); define
785 CONFIG_USB_UHCI to enable it.
786 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
787 end define CONFIG_USB_STORAGE to enable the USB
790 Supported are USB Keyboards and USB Floppy drives
792 MPC5200 USB requires additional defines:
794 for 528 MHz Clock: 0x0001bbbb
796 for differential drivers: 0x00001000
797 for single ended drivers: 0x00005000
801 The MMC controller on the Intel PXA is supported. To
802 enable this define CONFIG_MMC. The MMC can be
803 accessed from the boot prompt by mapping the device
804 to physical memory similar to flash. Command line is
805 enabled with CFG_CMD_MMC. The MMC driver also works with
806 the FAT fs. This is enabled with CFG_CMD_FAT.
808 - Journaling Flash filesystem support:
809 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
810 CONFIG_JFFS2_NAND_DEV
811 Define these for a default partition on a NAND device
813 CFG_JFFS2_FIRST_SECTOR,
814 CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
815 Define these for a default partition on a NOR device
818 Define this to create an own partition. You have to provide a
819 function struct part_info* jffs2_part_info(int part_num)
821 If you define only one JFFS2 partition you may also want to
822 #define CFG_JFFS_SINGLE_PART 1
823 to disable the command chpart. This is the default when you
824 have not defined a custom partition
829 Define this to enable standard (PC-Style) keyboard
833 Standard PC keyboard driver with US (is default) and
834 GERMAN key layout (switch via environment 'keymap=de') support.
835 Export function i8042_kbd_init, i8042_tstc and i8042_getc
836 for cfb_console. Supports cursor blinking.
841 Define this to enable video support (for output to
846 Enable Chips & Technologies 69000 Video chip
848 CONFIG_VIDEO_SMI_LYNXEM
849 Enable Silicon Motion SMI 712/710/810 Video chip. The
850 video output is selected via environment 'videoout'
851 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
854 For the CT69000 and SMI_LYNXEM drivers, videomode is
855 selected via environment 'videomode'. Two diferent ways
857 - "videomode=num" 'num' is a standard LiLo mode numbers.
858 Following standard modes are supported (* is default):
860 Colors 640x480 800x600 1024x768 1152x864 1280x1024
861 -------------+---------------------------------------------
862 8 bits | 0x301* 0x303 0x305 0x161 0x307
863 15 bits | 0x310 0x313 0x316 0x162 0x319
864 16 bits | 0x311 0x314 0x317 0x163 0x31A
865 24 bits | 0x312 0x315 0x318 ? 0x31B
866 -------------+---------------------------------------------
867 (i.e. setenv videomode 317; saveenv; reset;)
869 - "videomode=bootargs" all the video parameters are parsed
870 from the bootargs. (See drivers/videomodes.c)
873 CONFIG_VIDEO_SED13806
874 Enable Epson SED13806 driver. This driver supports 8bpp
875 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
876 or CONFIG_VIDEO_SED13806_16BPP
881 Define this to enable a custom keyboard support.
882 This simply calls drv_keyboard_init() which must be
883 defined in your board-specific files.
884 The only board using this so far is RBC823.
886 - LCD Support: CONFIG_LCD
888 Define this to enable LCD support (for output to LCD
889 display); also select one of the supported displays
890 by defining one of these:
892 CONFIG_NEC_NL6448AC33:
894 NEC NL6448AC33-18. Active, color, single scan.
896 CONFIG_NEC_NL6448BC20
898 NEC NL6448BC20-08. 6.5", 640x480.
899 Active, color, single scan.
901 CONFIG_NEC_NL6448BC33_54
903 NEC NL6448BC33-54. 10.4", 640x480.
904 Active, color, single scan.
908 Sharp 320x240. Active, color, single scan.
909 It isn't 16x9, and I am not sure what it is.
911 CONFIG_SHARP_LQ64D341
913 Sharp LQ64D341 display, 640x480.
914 Active, color, single scan.
918 HLD1045 display, 640x480.
919 Active, color, single scan.
923 Optrex CBL50840-2 NF-FW 99 22 M5
925 Hitachi LMG6912RPFC-00T
929 320x240. Black & white.
931 Normally display is black on white background; define
932 CFG_WHITE_ON_BLACK to get it inverted.
934 - Splash Screen Support: CONFIG_SPLASH_SCREEN
936 If this option is set, the environment is checked for
937 a variable "splashimage". If found, the usual display
938 of logo, copyright and system information on the LCD
939 is suppressed and the BMP image at the address
940 specified in "splashimage" is loaded instead. The
941 console is redirected to the "nulldev", too. This
942 allows for a "silent" boot where a splash screen is
943 loaded very quickly after power-on.
945 - Compression support:
948 If this option is set, support for bzip2 compressed
949 images is included. If not, only uncompressed and gzip
950 compressed images are supported.
952 NOTE: the bzip2 algorithm requires a lot of RAM, so
953 the malloc area (as defined by CFG_MALLOC_LEN) should
959 The address of PHY on MII bus.
961 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
963 The clock frequency of the MII bus
967 If this option is set, support for speed/duplex
968 detection of Gigabit PHY is included.
970 CONFIG_PHY_RESET_DELAY
972 Some PHY like Intel LXT971A need extra delay after
973 reset before any MII register access is possible.
974 For such PHY, set this option to the usec delay
975 required. (minimum 300usec for LXT971A)
977 CONFIG_PHY_CMD_DELAY (ppc4xx)
979 Some PHY like Intel LXT971A need extra delay after
980 command issued before MII status register can be read
987 Define a default value for ethernet address to use
988 for the respective ethernet interface, in case this
989 is not determined automatically.
994 Define a default value for the IP address to use for
995 the default ethernet interface, in case this is not
996 determined through e.g. bootp.
1001 Defines a default value for theIP address of a TFTP
1002 server to contact when using the "tftboot" command.
1004 - BOOTP Recovery Mode:
1005 CONFIG_BOOTP_RANDOM_DELAY
1007 If you have many targets in a network that try to
1008 boot using BOOTP, you may want to avoid that all
1009 systems send out BOOTP requests at precisely the same
1010 moment (which would happen for instance at recovery
1011 from a power failure, when all systems will try to
1012 boot, thus flooding the BOOTP server. Defining
1013 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1014 inserted before sending out BOOTP requests. The
1015 following delays are insterted then:
1017 1st BOOTP request: delay 0 ... 1 sec
1018 2nd BOOTP request: delay 0 ... 2 sec
1019 3rd BOOTP request: delay 0 ... 4 sec
1021 BOOTP requests: delay 0 ... 8 sec
1023 - DHCP Advanced Options:
1026 You can fine tune the DHCP functionality by adding
1027 these flags to the CONFIG_BOOTP_MASK define:
1029 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1030 serverip from a DHCP server, it is possible that more
1031 than one DNS serverip is offered to the client.
1032 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1033 serverip will be stored in the additional environment
1034 variable "dnsip2". The first DNS serverip is always
1035 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1036 is added to the CONFIG_BOOTP_MASK.
1038 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1039 to do a dynamic update of a DNS server. To do this, they
1040 need the hostname of the DHCP requester.
1041 If CONFIG_BOOP_SEND_HOSTNAME is added to the
1042 CONFIG_BOOTP_MASK, the content of the "hostname"
1043 environment variable is passed as option 12 to
1047 CONFIG_CDP_DEVICE_ID
1049 The device id used in CDP trigger frames.
1051 CONFIG_CDP_DEVICE_ID_PREFIX
1053 A two character string which is prefixed to the MAC address
1058 A printf format string which contains the ascii name of
1059 the port. Normally is set to "eth%d" which sets
1060 eth0 for the first ethernet, eth1 for the second etc.
1062 CONFIG_CDP_CAPABILITIES
1064 A 32bit integer which indicates the device capabilities;
1065 0x00000010 for a normal host which does not forwards.
1069 An ascii string containing the version of the software.
1073 An ascii string containing the name of the platform.
1077 A 32bit integer sent on the trigger.
1079 CONFIG_CDP_POWER_CONSUMPTION
1081 A 16bit integer containing the power consumption of the
1082 device in .1 of milliwatts.
1084 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1086 A byte containing the id of the VLAN.
1088 - Status LED: CONFIG_STATUS_LED
1090 Several configurations allow to display the current
1091 status using a LED. For instance, the LED will blink
1092 fast while running U-Boot code, stop blinking as
1093 soon as a reply to a BOOTP request was received, and
1094 start blinking slow once the Linux kernel is running
1095 (supported by a status LED driver in the Linux
1096 kernel). Defining CONFIG_STATUS_LED enables this
1099 - CAN Support: CONFIG_CAN_DRIVER
1101 Defining CONFIG_CAN_DRIVER enables CAN driver support
1102 on those systems that support this (optional)
1103 feature, like the TQM8xxL modules.
1105 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1107 These enable I2C serial bus commands. Defining either of
1108 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1109 include the appropriate I2C driver for the selected cpu.
1111 This will allow you to use i2c commands at the u-boot
1112 command line (as long as you set CFG_CMD_I2C in
1113 CONFIG_COMMANDS) and communicate with i2c based realtime
1114 clock chips. See common/cmd_i2c.c for a description of the
1115 command line interface.
1117 CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
1119 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1120 bit-banging) driver instead of CPM or similar hardware
1123 There are several other quantities that must also be
1124 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1126 In both cases you will need to define CFG_I2C_SPEED
1127 to be the frequency (in Hz) at which you wish your i2c bus
1128 to run and CFG_I2C_SLAVE to be the address of this node (ie
1129 the cpu's i2c node address).
1131 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1132 sets the cpu up as a master node and so its address should
1133 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1134 p.16-473). So, set CFG_I2C_SLAVE to 0.
1136 That's all that's required for CONFIG_HARD_I2C.
1138 If you use the software i2c interface (CONFIG_SOFT_I2C)
1139 then the following macros need to be defined (examples are
1140 from include/configs/lwmon.h):
1144 (Optional). Any commands necessary to enable the I2C
1145 controller or configure ports.
1147 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1151 (Only for MPC8260 CPU). The I/O port to use (the code
1152 assumes both bits are on the same port). Valid values
1153 are 0..3 for ports A..D.
1157 The code necessary to make the I2C data line active
1158 (driven). If the data line is open collector, this
1161 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1165 The code necessary to make the I2C data line tri-stated
1166 (inactive). If the data line is open collector, this
1169 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1173 Code that returns TRUE if the I2C data line is high,
1176 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1180 If <bit> is TRUE, sets the I2C data line high. If it
1181 is FALSE, it clears it (low).
1183 eg: #define I2C_SDA(bit) \
1184 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1185 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1189 If <bit> is TRUE, sets the I2C clock line high. If it
1190 is FALSE, it clears it (low).
1192 eg: #define I2C_SCL(bit) \
1193 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1194 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1198 This delay is invoked four times per clock cycle so this
1199 controls the rate of data transfer. The data rate thus
1200 is 1 / (I2C_DELAY * 4). Often defined to be something
1203 #define I2C_DELAY udelay(2)
1207 When a board is reset during an i2c bus transfer
1208 chips might think that the current transfer is still
1209 in progress. On some boards it is possible to access
1210 the i2c SCLK line directly, either by using the
1211 processor pin as a GPIO or by having a second pin
1212 connected to the bus. If this option is defined a
1213 custom i2c_init_board() routine in boards/xxx/board.c
1214 is run early in the boot sequence.
1216 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1218 This option enables configuration of bi_iic_fast[] flags
1219 in u-boot bd_info structure based on u-boot environment
1220 variable "i2cfast". (see also i2cfast)
1222 - SPI Support: CONFIG_SPI
1224 Enables SPI driver (so far only tested with
1225 SPI EEPROM, also an instance works with Crystal A/D and
1226 D/As on the SACSng board)
1230 Enables extended (16-bit) SPI EEPROM addressing.
1231 (symmetrical to CONFIG_I2C_X)
1235 Enables a software (bit-bang) SPI driver rather than
1236 using hardware support. This is a general purpose
1237 driver that only requires three general I/O port pins
1238 (two outputs, one input) to function. If this is
1239 defined, the board configuration must define several
1240 SPI configuration items (port pins to use, etc). For
1241 an example, see include/configs/sacsng.h.
1243 - FPGA Support: CONFIG_FPGA_COUNT
1245 Specify the number of FPGA devices to support.
1249 Used to specify the types of FPGA devices. For example,
1250 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1252 CFG_FPGA_PROG_FEEDBACK
1254 Enable printing of hash marks during FPGA configuration.
1258 Enable checks on FPGA configuration interface busy
1259 status by the configuration function. This option
1260 will require a board or device specific function to
1265 If defined, a function that provides delays in the FPGA
1266 configuration driver.
1268 CFG_FPGA_CHECK_CTRLC
1269 Allow Control-C to interrupt FPGA configuration
1271 CFG_FPGA_CHECK_ERROR
1273 Check for configuration errors during FPGA bitfile
1274 loading. For example, abort during Virtex II
1275 configuration if the INIT_B line goes low (which
1276 indicated a CRC error).
1280 Maximum time to wait for the INIT_B line to deassert
1281 after PROB_B has been deasserted during a Virtex II
1282 FPGA configuration sequence. The default time is 500
1287 Maximum time to wait for BUSY to deassert during
1288 Virtex II FPGA configuration. The default is 5 mS.
1290 CFG_FPGA_WAIT_CONFIG
1292 Time to wait after FPGA configuration. The default is
1295 - Configuration Management:
1298 If defined, this string will be added to the U-Boot
1299 version information (U_BOOT_VERSION)
1301 - Vendor Parameter Protection:
1303 U-Boot considers the values of the environment
1304 variables "serial#" (Board Serial Number) and
1305 "ethaddr" (Ethernet Address) to be parameters that
1306 are set once by the board vendor / manufacturer, and
1307 protects these variables from casual modification by
1308 the user. Once set, these variables are read-only,
1309 and write or delete attempts are rejected. You can
1310 change this behviour:
1312 If CONFIG_ENV_OVERWRITE is #defined in your config
1313 file, the write protection for vendor parameters is
1314 completely disabled. Anybody can change or delete
1317 Alternatively, if you #define _both_ CONFIG_ETHADDR
1318 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1319 ethernet address is installed in the environment,
1320 which can be changed exactly ONCE by the user. [The
1321 serial# is unaffected by this, i. e. it remains
1327 Define this variable to enable the reservation of
1328 "protected RAM", i. e. RAM which is not overwritten
1329 by U-Boot. Define CONFIG_PRAM to hold the number of
1330 kB you want to reserve for pRAM. You can overwrite
1331 this default value by defining an environment
1332 variable "pram" to the number of kB you want to
1333 reserve. Note that the board info structure will
1334 still show the full amount of RAM. If pRAM is
1335 reserved, a new environment variable "mem" will
1336 automatically be defined to hold the amount of
1337 remaining RAM in a form that can be passed as boot
1338 argument to Linux, for instance like that:
1340 setenv bootargs ... mem=\$(mem)
1343 This way you can tell Linux not to use this memory,
1344 either, which results in a memory region that will
1345 not be affected by reboots.
1347 *WARNING* If your board configuration uses automatic
1348 detection of the RAM size, you must make sure that
1349 this memory test is non-destructive. So far, the
1350 following board configurations are known to be
1353 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1354 HERMES, IP860, RPXlite, LWMON, LANTEC,
1355 PCU_E, FLAGADM, TQM8260
1360 Define this variable to stop the system in case of a
1361 fatal error, so that you have to reset it manually.
1362 This is probably NOT a good idea for an embedded
1363 system where you want to system to reboot
1364 automatically as fast as possible, but it may be
1365 useful during development since you can try to debug
1366 the conditions that lead to the situation.
1368 CONFIG_NET_RETRY_COUNT
1370 This variable defines the number of retries for
1371 network operations like ARP, RARP, TFTP, or BOOTP
1372 before giving up the operation. If not defined, a
1373 default value of 5 is used.
1375 - Command Interpreter:
1378 Enable auto completion of commands using TAB.
1382 Define this variable to enable the "hush" shell (from
1383 Busybox) as command line interpreter, thus enabling
1384 powerful command line syntax like
1385 if...then...else...fi conditionals or `&&' and '||'
1386 constructs ("shell scripts").
1388 If undefined, you get the old, much simpler behaviour
1389 with a somewhat smaller memory footprint.
1394 This defines the secondary prompt string, which is
1395 printed when the command interpreter needs more input
1396 to complete a command. Usually "> ".
1400 In the current implementation, the local variables
1401 space and global environment variables space are
1402 separated. Local variables are those you define by
1403 simply typing `name=value'. To access a local
1404 variable later on, you have write `$name' or
1405 `${name}'; to execute the contents of a variable
1406 directly type `$name' at the command prompt.
1408 Global environment variables are those you use
1409 setenv/printenv to work with. To run a command stored
1410 in such a variable, you need to use the run command,
1411 and you must not use the '$' sign to access them.
1413 To store commands and special characters in a
1414 variable, please use double quotation marks
1415 surrounding the whole text of the variable, instead
1416 of the backslashes before semicolons and special
1419 - Default Environment:
1420 CONFIG_EXTRA_ENV_SETTINGS
1422 Define this to contain any number of null terminated
1423 strings (variable = value pairs) that will be part of
1424 the default environment compiled into the boot image.
1426 For example, place something like this in your
1427 board's config file:
1429 #define CONFIG_EXTRA_ENV_SETTINGS \
1433 Warning: This method is based on knowledge about the
1434 internal format how the environment is stored by the
1435 U-Boot code. This is NOT an official, exported
1436 interface! Although it is unlikely that this format
1437 will change soon, there is no guarantee either.
1438 You better know what you are doing here.
1440 Note: overly (ab)use of the default environment is
1441 discouraged. Make sure to check other ways to preset
1442 the environment like the autoscript function or the
1445 - DataFlash Support:
1446 CONFIG_HAS_DATAFLASH
1448 Defining this option enables DataFlash features and
1449 allows to read/write in Dataflash via the standard
1452 - SystemACE Support:
1455 Adding this option adds support for Xilinx SystemACE
1456 chips attached via some sort of local bus. The address
1457 of the chip must alsh be defined in the
1458 CFG_SYSTEMACE_BASE macro. For example:
1460 #define CONFIG_SYSTEMACE
1461 #define CFG_SYSTEMACE_BASE 0xf0000000
1463 When SystemACE support is added, the "ace" device type
1464 becomes available to the fat commands, i.e. fatls.
1466 - Show boot progress:
1467 CONFIG_SHOW_BOOT_PROGRESS
1469 Defining this option allows to add some board-
1470 specific code (calling a user-provided function
1471 "show_boot_progress(int)") that enables you to show
1472 the system's boot progress on some display (for
1473 example, some LED's) on your board. At the moment,
1474 the following checkpoints are implemented:
1477 1 common/cmd_bootm.c before attempting to boot an image
1478 -1 common/cmd_bootm.c Image header has bad magic number
1479 2 common/cmd_bootm.c Image header has correct magic number
1480 -2 common/cmd_bootm.c Image header has bad checksum
1481 3 common/cmd_bootm.c Image header has correct checksum
1482 -3 common/cmd_bootm.c Image data has bad checksum
1483 4 common/cmd_bootm.c Image data has correct checksum
1484 -4 common/cmd_bootm.c Image is for unsupported architecture
1485 5 common/cmd_bootm.c Architecture check OK
1486 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1487 6 common/cmd_bootm.c Image Type check OK
1488 -6 common/cmd_bootm.c gunzip uncompression error
1489 -7 common/cmd_bootm.c Unimplemented compression type
1490 7 common/cmd_bootm.c Uncompression OK
1491 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1492 8 common/cmd_bootm.c Image Type check OK
1493 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1494 9 common/cmd_bootm.c Start initial ramdisk verification
1495 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1496 -11 common/cmd_bootm.c Ramdisk header has bad checksum
1497 10 common/cmd_bootm.c Ramdisk header is OK
1498 -12 common/cmd_bootm.c Ramdisk data has bad checksum
1499 11 common/cmd_bootm.c Ramdisk data has correct checksum
1500 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1501 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1502 13 common/cmd_bootm.c Start multifile image verification
1503 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1504 15 common/cmd_bootm.c All preparation done, transferring control to OS
1506 -30 lib_ppc/board.c Fatal error, hang the system
1507 -31 post/post.c POST test failed, detected by post_output_backlog()
1508 -32 post/post.c POST test failed, detected by post_run_single()
1510 -1 common/cmd_doc.c Bad usage of "doc" command
1511 -1 common/cmd_doc.c No boot device
1512 -1 common/cmd_doc.c Unknown Chip ID on boot device
1513 -1 common/cmd_doc.c Read Error on boot device
1514 -1 common/cmd_doc.c Image header has bad magic number
1516 -1 common/cmd_ide.c Bad usage of "ide" command
1517 -1 common/cmd_ide.c No boot device
1518 -1 common/cmd_ide.c Unknown boot device
1519 -1 common/cmd_ide.c Unknown partition table
1520 -1 common/cmd_ide.c Invalid partition type
1521 -1 common/cmd_ide.c Read Error on boot device
1522 -1 common/cmd_ide.c Image header has bad magic number
1524 -1 common/cmd_nand.c Bad usage of "nand" command
1525 -1 common/cmd_nand.c No boot device
1526 -1 common/cmd_nand.c Unknown Chip ID on boot device
1527 -1 common/cmd_nand.c Read Error on boot device
1528 -1 common/cmd_nand.c Image header has bad magic number
1530 -1 common/env_common.c Environment has a bad CRC, using default
1536 [so far only for SMDK2400 and TRAB boards]
1538 - Modem support endable:
1539 CONFIG_MODEM_SUPPORT
1541 - RTS/CTS Flow control enable:
1544 - Modem debug support:
1545 CONFIG_MODEM_SUPPORT_DEBUG
1547 Enables debugging stuff (char screen[1024], dbg())
1548 for modem support. Useful only with BDI2000.
1550 - Interrupt support (PPC):
1552 There are common interrupt_init() and timer_interrupt()
1553 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
1554 for cpu specific initialization. interrupt_init_cpu()
1555 should set decrementer_count to appropriate value. If
1556 cpu resets decrementer automatically after interrupt
1557 (ppc4xx) it should set decrementer_count to zero.
1558 timer_interrupt() calls timer_interrupt_cpu() for cpu
1559 specific handling. If board has watchdog / status_led
1560 / other_activity_monitor it works automatically from
1561 general timer_interrupt().
1565 In the target system modem support is enabled when a
1566 specific key (key combination) is pressed during
1567 power-on. Otherwise U-Boot will boot normally
1568 (autoboot). The key_pressed() fuction is called from
1569 board_init(). Currently key_pressed() is a dummy
1570 function, returning 1 and thus enabling modem
1573 If there are no modem init strings in the
1574 environment, U-Boot proceed to autoboot; the
1575 previous output (banner, info printfs) will be
1578 See also: doc/README.Modem
1581 Configuration Settings:
1582 -----------------------
1584 - CFG_LONGHELP: Defined when you want long help messages included;
1585 undefine this when you're short of memory.
1587 - CFG_PROMPT: This is what U-Boot prints on the console to
1588 prompt for user input.
1590 - CFG_CBSIZE: Buffer size for input from the Console
1592 - CFG_PBSIZE: Buffer size for Console output
1594 - CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1596 - CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1597 the application (usually a Linux kernel) when it is
1600 - CFG_BAUDRATE_TABLE:
1601 List of legal baudrate settings for this board.
1603 - CFG_CONSOLE_INFO_QUIET
1604 Suppress display of console information at boot.
1606 - CFG_CONSOLE_IS_IN_ENV
1607 If the board specific function
1608 extern int overwrite_console (void);
1609 returns 1, the stdin, stderr and stdout are switched to the
1610 serial port, else the settings in the environment are used.
1612 - CFG_CONSOLE_OVERWRITE_ROUTINE
1613 Enable the call to overwrite_console().
1615 - CFG_CONSOLE_ENV_OVERWRITE
1616 Enable overwrite of previous console environment settings.
1618 - CFG_MEMTEST_START, CFG_MEMTEST_END:
1619 Begin and End addresses of the area used by the
1623 Enable an alternate, more extensive memory test.
1625 - CFG_MEMTEST_SCRATCH:
1626 Scratch address used by the alternate memory test
1627 You only need to set this if address zero isn't writeable
1629 - CFG_TFTP_LOADADDR:
1630 Default load address for network file downloads
1632 - CFG_LOADS_BAUD_CHANGE:
1633 Enable temporary baudrate change while serial download
1636 Physical start address of SDRAM. _Must_ be 0 here.
1639 Physical start address of Motherboard I/O (if using a
1643 Physical start address of Flash memory.
1646 Physical start address of boot monitor code (set by
1647 make config files to be same as the text base address
1648 (TEXT_BASE) used when linking) - same as
1649 CFG_FLASH_BASE when booting from flash.
1652 Size of memory reserved for monitor code, used to
1653 determine _at_compile_time_ (!) if the environment is
1654 embedded within the U-Boot image, or in a separate
1658 Size of DRAM reserved for malloc() use.
1661 Maximum size of memory mapped by the startup code of
1662 the Linux kernel; all data that must be processed by
1663 the Linux kernel (bd_info, boot arguments, eventually
1664 initrd image) must be put below this limit.
1666 - CFG_MAX_FLASH_BANKS:
1667 Max number of Flash memory banks
1669 - CFG_MAX_FLASH_SECT:
1670 Max number of sectors on a Flash chip
1672 - CFG_FLASH_ERASE_TOUT:
1673 Timeout for Flash erase operations (in ms)
1675 - CFG_FLASH_WRITE_TOUT:
1676 Timeout for Flash write operations (in ms)
1678 - CFG_FLASH_LOCK_TOUT
1679 Timeout for Flash set sector lock bit operation (in ms)
1681 - CFG_FLASH_UNLOCK_TOUT
1682 Timeout for Flash clear lock bits operation (in ms)
1684 - CFG_FLASH_PROTECTION
1685 If defined, hardware flash sectors protection is used
1686 instead of U-Boot software protection.
1688 - CFG_DIRECT_FLASH_TFTP:
1690 Enable TFTP transfers directly to flash memory;
1691 without this option such a download has to be
1692 performed in two steps: (1) download to RAM, and (2)
1693 copy from RAM to flash.
1695 The two-step approach is usually more reliable, since
1696 you can check if the download worked before you erase
1697 the flash, but in some situations (when sytem RAM is
1698 too limited to allow for a tempory copy of the
1699 downloaded image) this option may be very useful.
1702 Define if the flash driver uses extra elements in the
1703 common flash structure for storing flash geometry.
1705 - CFG_FLASH_CFI_DRIVER
1706 This option also enables the building of the cfi_flash driver
1707 in the drivers directory
1709 - CFG_RX_ETH_BUFFER:
1710 Defines the number of ethernet receive buffers. On some
1711 ethernet controllers it is recommended to set this value
1712 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1713 buffers can be full shortly after enabling the interface
1714 on high ethernet traffic.
1715 Defaults to 4 if not defined.
1717 The following definitions that deal with the placement and management
1718 of environment data (variable area); in general, we support the
1719 following configurations:
1721 - CFG_ENV_IS_IN_FLASH:
1723 Define this if the environment is in flash memory.
1725 a) The environment occupies one whole flash sector, which is
1726 "embedded" in the text segment with the U-Boot code. This
1727 happens usually with "bottom boot sector" or "top boot
1728 sector" type flash chips, which have several smaller
1729 sectors at the start or the end. For instance, such a
1730 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1731 such a case you would place the environment in one of the
1732 4 kB sectors - with U-Boot code before and after it. With
1733 "top boot sector" type flash chips, you would put the
1734 environment in one of the last sectors, leaving a gap
1735 between U-Boot and the environment.
1739 Offset of environment data (variable area) to the
1740 beginning of flash memory; for instance, with bottom boot
1741 type flash chips the second sector can be used: the offset
1742 for this sector is given here.
1744 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1748 This is just another way to specify the start address of
1749 the flash sector containing the environment (instead of
1752 - CFG_ENV_SECT_SIZE:
1754 Size of the sector containing the environment.
1757 b) Sometimes flash chips have few, equal sized, BIG sectors.
1758 In such a case you don't want to spend a whole sector for
1763 If you use this in combination with CFG_ENV_IS_IN_FLASH
1764 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1765 of this flash sector for the environment. This saves
1766 memory for the RAM copy of the environment.
1768 It may also save flash memory if you decide to use this
1769 when your environment is "embedded" within U-Boot code,
1770 since then the remainder of the flash sector could be used
1771 for U-Boot code. It should be pointed out that this is
1772 STRONGLY DISCOURAGED from a robustness point of view:
1773 updating the environment in flash makes it always
1774 necessary to erase the WHOLE sector. If something goes
1775 wrong before the contents has been restored from a copy in
1776 RAM, your target system will be dead.
1778 - CFG_ENV_ADDR_REDUND
1781 These settings describe a second storage area used to hold
1782 a redundand copy of the environment data, so that there is
1783 a valid backup copy in case there is a power failure during
1784 a "saveenv" operation.
1786 BE CAREFUL! Any changes to the flash layout, and some changes to the
1787 source code will make it necessary to adapt <board>/u-boot.lds*
1791 - CFG_ENV_IS_IN_NVRAM:
1793 Define this if you have some non-volatile memory device
1794 (NVRAM, battery buffered SRAM) which you want to use for the
1800 These two #defines are used to determin the memory area you
1801 want to use for environment. It is assumed that this memory
1802 can just be read and written to, without any special
1805 BE CAREFUL! The first access to the environment happens quite early
1806 in U-Boot initalization (when we try to get the setting of for the
1807 console baudrate). You *MUST* have mappend your NVRAM area then, or
1810 Please note that even with NVRAM we still use a copy of the
1811 environment in RAM: we could work on NVRAM directly, but we want to
1812 keep settings there always unmodified except somebody uses "saveenv"
1813 to save the current settings.
1816 - CFG_ENV_IS_IN_EEPROM:
1818 Use this if you have an EEPROM or similar serial access
1819 device and a driver for it.
1824 These two #defines specify the offset and size of the
1825 environment area within the total memory of your EEPROM.
1827 - CFG_I2C_EEPROM_ADDR:
1828 If defined, specified the chip address of the EEPROM device.
1829 The default address is zero.
1831 - CFG_EEPROM_PAGE_WRITE_BITS:
1832 If defined, the number of bits used to address bytes in a
1833 single page in the EEPROM device. A 64 byte page, for example
1834 would require six bits.
1836 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1837 If defined, the number of milliseconds to delay between
1838 page writes. The default is zero milliseconds.
1840 - CFG_I2C_EEPROM_ADDR_LEN:
1841 The length in bytes of the EEPROM memory array address. Note
1842 that this is NOT the chip address length!
1844 - CFG_I2C_EEPROM_ADDR_OVERFLOW:
1845 EEPROM chips that implement "address overflow" are ones
1846 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
1847 address and the extra bits end up in the "chip address" bit
1848 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
1851 Note that we consider the length of the address field to
1852 still be one byte because the extra address bits are hidden
1853 in the chip address.
1856 The size in bytes of the EEPROM device.
1859 - CFG_ENV_IS_IN_DATAFLASH:
1861 Define this if you have a DataFlash memory device which you
1862 want to use for the environment.
1868 These three #defines specify the offset and size of the
1869 environment area within the total memory of your DataFlash placed
1870 at the specified address.
1872 - CFG_ENV_IS_IN_NAND:
1874 Define this if you have a NAND device which you want to use
1875 for the environment.
1880 These two #defines specify the offset and size of the environment
1881 area within the first NAND device.
1883 - CFG_SPI_INIT_OFFSET
1885 Defines offset to the initial SPI buffer area in DPRAM. The
1886 area is used at an early stage (ROM part) if the environment
1887 is configured to reside in the SPI EEPROM: We need a 520 byte
1888 scratch DPRAM area. It is used between the two initialization
1889 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1890 to be a good choice since it makes it far enough from the
1891 start of the data area as well as from the stack pointer.
1893 Please note that the environment is read-only as long as the monitor
1894 has been relocated to RAM and a RAM copy of the environment has been
1895 created; also, when using EEPROM you will have to use getenv_r()
1896 until then to read environment variables.
1898 The environment is protected by a CRC32 checksum. Before the monitor
1899 is relocated into RAM, as a result of a bad CRC you will be working
1900 with the compiled-in default environment - *silently*!!! [This is
1901 necessary, because the first environment variable we need is the
1902 "baudrate" setting for the console - if we have a bad CRC, we don't
1903 have any device yet where we could complain.]
1905 Note: once the monitor has been relocated, then it will complain if
1906 the default environment is used; a new CRC is computed as soon as you
1907 use the "saveenv" command to store a valid environment.
1909 - CFG_FAULT_ECHO_LINK_DOWN:
1910 Echo the inverted Ethernet link state to the fault LED.
1912 Note: If this option is active, then CFG_FAULT_MII_ADDR
1913 also needs to be defined.
1915 - CFG_FAULT_MII_ADDR:
1916 MII address of the PHY to check for the Ethernet link state.
1918 - CFG_64BIT_VSPRINTF:
1919 Makes vsprintf (and all *printf functions) support printing
1920 of 64bit values by using the L quantifier
1922 - CFG_64BIT_STRTOUL:
1923 Adds simple_strtoull that returns a 64bit value
1925 Low Level (hardware related) configuration options:
1926 ---------------------------------------------------
1928 - CFG_CACHELINE_SIZE:
1929 Cache Line Size of the CPU.
1932 Default address of the IMMR after system reset.
1934 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
1935 and RPXsuper) to be able to adjust the position of
1936 the IMMR register after a reset.
1938 - Floppy Disk Support:
1939 CFG_FDC_DRIVE_NUMBER
1941 the default drive number (default value 0)
1945 defines the spacing between fdc chipset registers
1950 defines the offset of register from address. It
1951 depends on which part of the data bus is connected to
1952 the fdc chipset. (default value 0)
1954 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1955 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1958 if CFG_FDC_HW_INIT is defined, then the function
1959 fdc_hw_init() is called at the beginning of the FDC
1960 setup. fdc_hw_init() must be provided by the board
1961 source code. It is used to make hardware dependant
1964 - CFG_IMMR: Physical address of the Internal Memory Mapped
1965 Register; DO NOT CHANGE! (11-4)
1966 [MPC8xx systems only]
1968 - CFG_INIT_RAM_ADDR:
1970 Start address of memory area that can be used for
1971 initial data and stack; please note that this must be
1972 writable memory that is working WITHOUT special
1973 initialization, i. e. you CANNOT use normal RAM which
1974 will become available only after programming the
1975 memory controller and running certain initialization
1978 U-Boot uses the following memory types:
1979 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
1980 - MPC824X: data cache
1981 - PPC4xx: data cache
1983 - CFG_GBL_DATA_OFFSET:
1985 Offset of the initial data structure in the memory
1986 area defined by CFG_INIT_RAM_ADDR. Usually
1987 CFG_GBL_DATA_OFFSET is chosen such that the initial
1988 data is located at the end of the available space
1989 (sometimes written as (CFG_INIT_RAM_END -
1990 CFG_INIT_DATA_SIZE), and the initial stack is just
1991 below that area (growing from (CFG_INIT_RAM_ADDR +
1992 CFG_GBL_DATA_OFFSET) downward.
1995 On the MPC824X (or other systems that use the data
1996 cache for initial memory) the address chosen for
1997 CFG_INIT_RAM_ADDR is basically arbitrary - it must
1998 point to an otherwise UNUSED address space between
1999 the top of RAM and the start of the PCI space.
2001 - CFG_SIUMCR: SIU Module Configuration (11-6)
2003 - CFG_SYPCR: System Protection Control (11-9)
2005 - CFG_TBSCR: Time Base Status and Control (11-26)
2007 - CFG_PISCR: Periodic Interrupt Status and Control (11-31)
2009 - CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2011 - CFG_SCCR: System Clock and reset Control Register (15-27)
2013 - CFG_OR_TIMING_SDRAM:
2017 periodic timer for refresh
2019 - CFG_DER: Debug Event Register (37-47)
2021 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
2022 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
2023 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
2025 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2027 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2028 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
2029 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
2030 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2032 - CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
2033 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
2034 Machine Mode Register and Memory Periodic Timer
2035 Prescaler definitions (SDRAM timing)
2037 - CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
2038 enable I2C microcode relocation patch (MPC8xx);
2039 define relocation offset in DPRAM [DSP2]
2041 - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
2042 enable SPI microcode relocation patch (MPC8xx);
2043 define relocation offset in DPRAM [SCC4]
2046 Use OSCM clock mode on MBX8xx board. Be careful,
2047 wrong setting might damage your board. Read
2048 doc/README.MBX before setting this variable!
2050 - CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2051 Offset of the bootmode word in DPRAM used by post
2052 (Power On Self Tests). This definition overrides
2053 #define'd default value in commproc.h resp.
2056 - CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
2057 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
2058 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
2059 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
2060 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2061 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
2062 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
2063 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
2064 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2066 - CONFIG_ETHER_ON_FEC[12]
2067 Define to enable FEC[12] on a 8xx series processor.
2069 - CONFIG_FEC[12]_PHY
2070 Define to the hardcoded PHY address which corresponds
2071 to the given FEC; i. e.
2072 #define CONFIG_FEC1_PHY 4
2073 means that the PHY with address 4 is connected to FEC1
2075 When set to -1, means to probe for first available.
2077 - CONFIG_FEC[12]_PHY_NORXERR
2078 The PHY does not have a RXERR line (RMII only).
2079 (so program the FEC to ignore it).
2082 Enable RMII mode for all FECs.
2083 Note that this is a global option, we can't
2084 have one FEC in standard MII mode and another in RMII mode.
2086 - CONFIG_CRC32_VERIFY
2087 Add a verify option to the crc32 command.
2090 => crc32 -v <address> <count> <crc32>
2092 Where address/count indicate a memory area
2093 and crc32 is the correct crc32 which the
2097 Add the "loopw" memory command. This only takes effect if
2098 the memory commands are activated globally (CFG_CMD_MEM).
2100 Building the Software:
2101 ======================
2103 Building U-Boot has been tested in native PPC environments (on a
2104 PowerBook G3 running LinuxPPC 2000) and in cross environments
2105 (running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
2108 If you are not using a native PPC environment, it is assumed that you
2109 have the GNU cross compiling tools available in your path and named
2110 with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
2111 you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
2112 the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
2115 CROSS_COMPILE = ppc_4xx-
2118 U-Boot is intended to be simple to build. After installing the
2119 sources you must configure U-Boot for one specific board type. This
2124 where "NAME_config" is the name of one of the existing
2125 configurations; the following names are supported:
2127 ADCIOP_config FPS860L_config omap730p2_config
2128 ADS860_config GEN860T_config pcu_e_config
2129 AR405_config GENIETV_config PIP405_config
2130 at91rm9200dk_config GTH_config QS823_config
2131 CANBT_config hermes_config QS850_config
2132 cmi_mpc5xx_config hymod_config QS860T_config
2133 cogent_common_config IP860_config RPXlite_config
2134 cogent_mpc8260_config IVML24_config RPXlite_DW_config
2135 cogent_mpc8xx_config IVMS8_config RPXsuper_config
2136 CPCI405_config JSE_config rsdproto_config
2137 CPCIISER4_config LANTEC_config Sandpoint8240_config
2138 csb272_config lwmon_config sbc8260_config
2139 CU824_config MBX860T_config sbc8560_33_config
2140 DUET_ADS_config MBX_config sbc8560_66_config
2141 EBONY_config MPC8260ADS_config SM850_config
2142 ELPT860_config MPC8540ADS_config SPD823TS_config
2143 ESTEEM192E_config MPC8560ADS_config stxgp3_config
2144 ETX094_config NETVIA_config SXNI855T_config
2145 FADS823_config omap1510inn_config TQM823L_config
2146 FADS850SAR_config omap1610h2_config TQM850L_config
2147 FADS860T_config omap1610inn_config TQM855L_config
2148 FPS850L_config omap5912osk_config TQM860L_config
2152 Note: for some board special configuration names may exist; check if
2153 additional information is available from the board vendor; for
2154 instance, the TQM823L systems are available without (standard)
2155 or with LCD support. You can select such additional "features"
2156 when chosing the configuration, i. e.
2159 - will configure for a plain TQM823L, i. e. no LCD support
2161 make TQM823L_LCD_config
2162 - will configure for a TQM823L with U-Boot console on LCD
2167 Finally, type "make all", and you should get some working U-Boot
2168 images ready for download to / installation on your system:
2170 - "u-boot.bin" is a raw binary image
2171 - "u-boot" is an image in ELF binary format
2172 - "u-boot.srec" is in Motorola S-Record format
2175 Please be aware that the Makefiles assume you are using GNU make, so
2176 for instance on NetBSD you might need to use "gmake" instead of
2180 If the system board that you have is not listed, then you will need
2181 to port U-Boot to your hardware platform. To do this, follow these
2184 1. Add a new configuration option for your board to the toplevel
2185 "Makefile" and to the "MAKEALL" script, using the existing
2186 entries as examples. Note that here and at many other places
2187 boards and other names are listed in alphabetical sort order. Please
2189 2. Create a new directory to hold your board specific code. Add any
2190 files you need. In your board directory, you will need at least
2191 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2192 3. Create a new configuration file "include/configs/<board>.h" for
2194 3. If you're porting U-Boot to a new CPU, then also create a new
2195 directory to hold your CPU specific code. Add any files you need.
2196 4. Run "make <board>_config" with your new name.
2197 5. Type "make", and you should get a working "u-boot.srec" file
2198 to be installed on your target system.
2199 6. Debug and solve any problems that might arise.
2200 [Of course, this last step is much harder than it sounds.]
2203 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2204 ==============================================================
2206 If you have modified U-Boot sources (for instance added a new board
2207 or support for new devices, a new CPU, etc.) you are expected to
2208 provide feedback to the other developers. The feedback normally takes
2209 the form of a "patch", i. e. a context diff against a certain (latest
2210 official or latest in CVS) version of U-Boot sources.
2212 But before you submit such a patch, please verify that your modifi-
2213 cation did not break existing code. At least make sure that *ALL* of
2214 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2215 just run the "MAKEALL" script, which will configure and build U-Boot
2216 for ALL supported system. Be warned, this will take a while. You can
2217 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2218 environment variable to the script, i. e. to use the cross tools from
2219 MontaVista's Hard Hat Linux you can type
2221 CROSS_COMPILE=ppc_8xx- MAKEALL
2223 or to build on a native PowerPC system you can type
2225 CROSS_COMPILE=' ' MAKEALL
2227 See also "U-Boot Porting Guide" below.
2230 Monitor Commands - Overview:
2231 ============================
2233 go - start application at address 'addr'
2234 run - run commands in an environment variable
2235 bootm - boot application image from memory
2236 bootp - boot image via network using BootP/TFTP protocol
2237 tftpboot- boot image via network using TFTP protocol
2238 and env variables "ipaddr" and "serverip"
2239 (and eventually "gatewayip")
2240 rarpboot- boot image via network using RARP/TFTP protocol
2241 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2242 loads - load S-Record file over serial line
2243 loadb - load binary file over serial line (kermit mode)
2245 mm - memory modify (auto-incrementing)
2246 nm - memory modify (constant address)
2247 mw - memory write (fill)
2249 cmp - memory compare
2250 crc32 - checksum calculation
2251 imd - i2c memory display
2252 imm - i2c memory modify (auto-incrementing)
2253 inm - i2c memory modify (constant address)
2254 imw - i2c memory write (fill)
2255 icrc32 - i2c checksum calculation
2256 iprobe - probe to discover valid I2C chip addresses
2257 iloop - infinite loop on address range
2258 isdram - print SDRAM configuration information
2259 sspi - SPI utility commands
2260 base - print or set address offset
2261 printenv- print environment variables
2262 setenv - set environment variables
2263 saveenv - save environment variables to persistent storage
2264 protect - enable or disable FLASH write protection
2265 erase - erase FLASH memory
2266 flinfo - print FLASH memory information
2267 bdinfo - print Board Info structure
2268 iminfo - print header information for application image
2269 coninfo - print console devices and informations
2270 ide - IDE sub-system
2271 loop - infinite loop on address range
2272 loopw - infinite write loop on address range
2273 mtest - simple RAM test
2274 icache - enable or disable instruction cache
2275 dcache - enable or disable data cache
2276 reset - Perform RESET of the CPU
2277 echo - echo args to console
2278 version - print monitor version
2279 help - print online help
2280 ? - alias for 'help'
2283 Monitor Commands - Detailed Description:
2284 ========================================
2288 For now: just type "help <command>".
2291 Environment Variables:
2292 ======================
2294 U-Boot supports user configuration using Environment Variables which
2295 can be made persistent by saving to Flash memory.
2297 Environment Variables are set using "setenv", printed using
2298 "printenv", and saved to Flash using "saveenv". Using "setenv"
2299 without a value can be used to delete a variable from the
2300 environment. As long as you don't save the environment you are
2301 working with an in-memory copy. In case the Flash area containing the
2302 environment is erased by accident, a default environment is provided.
2304 Some configuration options can be set using Environment Variables:
2306 baudrate - see CONFIG_BAUDRATE
2308 bootdelay - see CONFIG_BOOTDELAY
2310 bootcmd - see CONFIG_BOOTCOMMAND
2312 bootargs - Boot arguments when booting an RTOS image
2314 bootfile - Name of the image to load with TFTP
2316 autoload - if set to "no" (any string beginning with 'n'),
2317 "bootp" will just load perform a lookup of the
2318 configuration from the BOOTP server, but not try to
2319 load any image using TFTP
2321 autostart - if set to "yes", an image loaded using the "bootp",
2322 "rarpboot", "tftpboot" or "diskboot" commands will
2323 be automatically started (by internally calling
2326 If set to "no", a standalone image passed to the
2327 "bootm" command will be copied to the load address
2328 (and eventually uncompressed), but NOT be started.
2329 This can be used to load and uncompress arbitrary
2332 i2cfast - (PPC405GP|PPC405EP only)
2333 if set to 'y' configures Linux I2C driver for fast
2334 mode (400kHZ). This environment variable is used in
2335 initialization code. So, for changes to be effective
2336 it must be saved and board must be reset.
2338 initrd_high - restrict positioning of initrd images:
2339 If this variable is not set, initrd images will be
2340 copied to the highest possible address in RAM; this
2341 is usually what you want since it allows for
2342 maximum initrd size. If for some reason you want to
2343 make sure that the initrd image is loaded below the
2344 CFG_BOOTMAPSZ limit, you can set this environment
2345 variable to a value of "no" or "off" or "0".
2346 Alternatively, you can set it to a maximum upper
2347 address to use (U-Boot will still check that it
2348 does not overwrite the U-Boot stack and data).
2350 For instance, when you have a system with 16 MB
2351 RAM, and want to reserve 4 MB from use by Linux,
2352 you can do this by adding "mem=12M" to the value of
2353 the "bootargs" variable. However, now you must make
2354 sure that the initrd image is placed in the first
2355 12 MB as well - this can be done with
2357 setenv initrd_high 00c00000
2359 If you set initrd_high to 0xFFFFFFFF, this is an
2360 indication to U-Boot that all addresses are legal
2361 for the Linux kernel, including addresses in flash
2362 memory. In this case U-Boot will NOT COPY the
2363 ramdisk at all. This may be useful to reduce the
2364 boot time on your system, but requires that this
2365 feature is supported by your Linux kernel.
2367 ipaddr - IP address; needed for tftpboot command
2369 loadaddr - Default load address for commands like "bootp",
2370 "rarpboot", "tftpboot", "loadb" or "diskboot"
2372 loads_echo - see CONFIG_LOADS_ECHO
2374 serverip - TFTP server IP address; needed for tftpboot command
2376 bootretry - see CONFIG_BOOT_RETRY_TIME
2378 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2380 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2382 ethprime - When CONFIG_NET_MULTI is enabled controls which
2383 interface is used first.
2385 ethact - When CONFIG_NET_MULTI is enabled controls which
2386 interface is currently active. For example you
2387 can do the following
2389 => setenv ethact FEC ETHERNET
2390 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
2391 => setenv ethact SCC ETHERNET
2392 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
2394 netretry - When set to "no" each network operation will
2395 either succeed or fail without retrying.
2396 When set to "once" the network operation will
2397 fail when all the available network interfaces
2398 are tried once without success.
2399 Useful on scripts which control the retry operation
2402 vlan - When set to a value < 4095 the traffic over
2403 ethernet is encapsulated/received over 802.1q
2406 The following environment variables may be used and automatically
2407 updated by the network boot commands ("bootp" and "rarpboot"),
2408 depending the information provided by your boot server:
2410 bootfile - see above
2411 dnsip - IP address of your Domain Name Server
2412 dnsip2 - IP address of your secondary Domain Name Server
2413 gatewayip - IP address of the Gateway (Router) to use
2414 hostname - Target hostname
2416 netmask - Subnet Mask
2417 rootpath - Pathname of the root filesystem on the NFS server
2418 serverip - see above
2421 There are two special Environment Variables:
2423 serial# - contains hardware identification information such
2424 as type string and/or serial number
2425 ethaddr - Ethernet address
2427 These variables can be set only once (usually during manufacturing of
2428 the board). U-Boot refuses to delete or overwrite these variables
2429 once they have been set once.
2432 Further special Environment Variables:
2434 ver - Contains the U-Boot version string as printed
2435 with the "version" command. This variable is
2436 readonly (see CONFIG_VERSION_VARIABLE).
2439 Please note that changes to some configuration parameters may take
2440 only effect after the next boot (yes, that's just like Windoze :-).
2443 Command Line Parsing:
2444 =====================
2446 There are two different command line parsers available with U-Boot:
2447 the old "simple" one, and the much more powerful "hush" shell:
2449 Old, simple command line parser:
2450 --------------------------------
2452 - supports environment variables (through setenv / saveenv commands)
2453 - several commands on one line, separated by ';'
2454 - variable substitution using "... $(name) ..." syntax
2455 - special characters ('$', ';') can be escaped by prefixing with '\',
2457 setenv bootcmd bootm \$(address)
2458 - You can also escape text by enclosing in single apostrophes, for example:
2459 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2464 - similar to Bourne shell, with control structures like
2465 if...then...else...fi, for...do...done; while...do...done,
2466 until...do...done, ...
2467 - supports environment ("global") variables (through setenv / saveenv
2468 commands) and local shell variables (through standard shell syntax
2469 "name=value"); only environment variables can be used with "run"
2475 (1) If a command line (or an environment variable executed by a "run"
2476 command) contains several commands separated by semicolon, and
2477 one of these commands fails, then the remaining commands will be
2480 (2) If you execute several variables with one call to run (i. e.
2481 calling run with a list af variables as arguments), any failing
2482 command will cause "run" to terminate, i. e. the remaining
2483 variables are not executed.
2485 Note for Redundant Ethernet Interfaces:
2486 =======================================
2488 Some boards come with redundant ethernet interfaces; U-Boot supports
2489 such configurations and is capable of automatic selection of a
2490 "working" interface when needed. MAC assignment works as follows:
2492 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2493 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2494 "eth1addr" (=>eth1), "eth2addr", ...
2496 If the network interface stores some valid MAC address (for instance
2497 in SROM), this is used as default address if there is NO correspon-
2498 ding setting in the environment; if the corresponding environment
2499 variable is set, this overrides the settings in the card; that means:
2501 o If the SROM has a valid MAC address, and there is no address in the
2502 environment, the SROM's address is used.
2504 o If there is no valid address in the SROM, and a definition in the
2505 environment exists, then the value from the environment variable is
2508 o If both the SROM and the environment contain a MAC address, and
2509 both addresses are the same, this MAC address is used.
2511 o If both the SROM and the environment contain a MAC address, and the
2512 addresses differ, the value from the environment is used and a
2515 o If neither SROM nor the environment contain a MAC address, an error
2522 The "boot" commands of this monitor operate on "image" files which
2523 can be basicly anything, preceeded by a special header; see the
2524 definitions in include/image.h for details; basicly, the header
2525 defines the following image properties:
2527 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2528 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2529 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2530 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2531 * Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2532 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2533 Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
2534 * Compression Type (uncompressed, gzip, bzip2)
2540 The header is marked by a special Magic Number, and both the header
2541 and the data portions of the image are secured against corruption by
2548 Although U-Boot should support any OS or standalone application
2549 easily, the main focus has always been on Linux during the design of
2552 U-Boot includes many features that so far have been part of some
2553 special "boot loader" code within the Linux kernel. Also, any
2554 "initrd" images to be used are no longer part of one big Linux image;
2555 instead, kernel and "initrd" are separate images. This implementation
2556 serves several purposes:
2558 - the same features can be used for other OS or standalone
2559 applications (for instance: using compressed images to reduce the
2560 Flash memory footprint)
2562 - it becomes much easier to port new Linux kernel versions because
2563 lots of low-level, hardware dependent stuff are done by U-Boot
2565 - the same Linux kernel image can now be used with different "initrd"
2566 images; of course this also means that different kernel images can
2567 be run with the same "initrd". This makes testing easier (you don't
2568 have to build a new "zImage.initrd" Linux image when you just
2569 change a file in your "initrd"). Also, a field-upgrade of the
2570 software is easier now.
2576 Porting Linux to U-Boot based systems:
2577 ---------------------------------------
2579 U-Boot cannot save you from doing all the necessary modifications to
2580 configure the Linux device drivers for use with your target hardware
2581 (no, we don't intend to provide a full virtual machine interface to
2584 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
2586 Just make sure your machine specific header file (for instance
2587 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2588 Information structure as we define in include/u-boot.h, and make
2589 sure that your definition of IMAP_ADDR uses the same value as your
2590 U-Boot configuration in CFG_IMMR.
2593 Configuring the Linux kernel:
2594 -----------------------------
2596 No specific requirements for U-Boot. Make sure you have some root
2597 device (initial ramdisk, NFS) for your target system.
2600 Building a Linux Image:
2601 -----------------------
2603 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2604 not used. If you use recent kernel source, a new build target
2605 "uImage" will exist which automatically builds an image usable by
2606 U-Boot. Most older kernels also have support for a "pImage" target,
2607 which was introduced for our predecessor project PPCBoot and uses a
2608 100% compatible format.
2617 The "uImage" build target uses a special tool (in 'tools/mkimage') to
2618 encapsulate a compressed Linux kernel image with header information,
2619 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
2621 * build a standard "vmlinux" kernel image (in ELF binary format):
2623 * convert the kernel into a raw binary image:
2625 ${CROSS_COMPILE}-objcopy -O binary \
2626 -R .note -R .comment \
2627 -S vmlinux linux.bin
2629 * compress the binary image:
2633 * package compressed binary image for U-Boot:
2635 mkimage -A ppc -O linux -T kernel -C gzip \
2636 -a 0 -e 0 -n "Linux Kernel Image" \
2637 -d linux.bin.gz uImage
2640 The "mkimage" tool can also be used to create ramdisk images for use
2641 with U-Boot, either separated from the Linux kernel image, or
2642 combined into one file. "mkimage" encapsulates the images with a 64
2643 byte header containing information about target architecture,
2644 operating system, image type, compression method, entry points, time
2645 stamp, CRC32 checksums, etc.
2647 "mkimage" can be called in two ways: to verify existing images and
2648 print the header information, or to build new images.
2650 In the first form (with "-l" option) mkimage lists the information
2651 contained in the header of an existing U-Boot image; this includes
2652 checksum verification:
2654 tools/mkimage -l image
2655 -l ==> list image header information
2657 The second form (with "-d" option) is used to build a U-Boot image
2658 from a "data file" which is used as image payload:
2660 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2661 -n name -d data_file image
2662 -A ==> set architecture to 'arch'
2663 -O ==> set operating system to 'os'
2664 -T ==> set image type to 'type'
2665 -C ==> set compression type 'comp'
2666 -a ==> set load address to 'addr' (hex)
2667 -e ==> set entry point to 'ep' (hex)
2668 -n ==> set image name to 'name'
2669 -d ==> use image data from 'datafile'
2671 Right now, all Linux kernels for PowerPC systems use the same load
2672 address (0x00000000), but the entry point address depends on the
2675 - 2.2.x kernels have the entry point at 0x0000000C,
2676 - 2.3.x and later kernels have the entry point at 0x00000000.
2678 So a typical call to build a U-Boot image would read:
2680 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2681 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2682 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2683 > examples/uImage.TQM850L
2684 Image Name: 2.4.4 kernel for TQM850L
2685 Created: Wed Jul 19 02:34:59 2000
2686 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2687 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2688 Load Address: 0x00000000
2689 Entry Point: 0x00000000
2691 To verify the contents of the image (or check for corruption):
2693 -> tools/mkimage -l examples/uImage.TQM850L
2694 Image Name: 2.4.4 kernel for TQM850L
2695 Created: Wed Jul 19 02:34:59 2000
2696 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2697 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2698 Load Address: 0x00000000
2699 Entry Point: 0x00000000
2701 NOTE: for embedded systems where boot time is critical you can trade
2702 speed for memory and install an UNCOMPRESSED image instead: this
2703 needs more space in Flash, but boots much faster since it does not
2704 need to be uncompressed:
2706 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2707 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2708 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2709 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2710 > examples/uImage.TQM850L-uncompressed
2711 Image Name: 2.4.4 kernel for TQM850L
2712 Created: Wed Jul 19 02:34:59 2000
2713 Image Type: PowerPC Linux Kernel Image (uncompressed)
2714 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2715 Load Address: 0x00000000
2716 Entry Point: 0x00000000
2719 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2720 when your kernel is intended to use an initial ramdisk:
2722 -> tools/mkimage -n 'Simple Ramdisk Image' \
2723 > -A ppc -O linux -T ramdisk -C gzip \
2724 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2725 Image Name: Simple Ramdisk Image
2726 Created: Wed Jan 12 14:01:50 2000
2727 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2728 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2729 Load Address: 0x00000000
2730 Entry Point: 0x00000000
2733 Installing a Linux Image:
2734 -------------------------
2736 To downloading a U-Boot image over the serial (console) interface,
2737 you must convert the image to S-Record format:
2739 objcopy -I binary -O srec examples/image examples/image.srec
2741 The 'objcopy' does not understand the information in the U-Boot
2742 image header, so the resulting S-Record file will be relative to
2743 address 0x00000000. To load it to a given address, you need to
2744 specify the target address as 'offset' parameter with the 'loads'
2747 Example: install the image to address 0x40100000 (which on the
2748 TQM8xxL is in the first Flash bank):
2750 => erase 40100000 401FFFFF
2756 ## Ready for S-Record download ...
2757 ~>examples/image.srec
2758 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2760 15989 15990 15991 15992
2761 [file transfer complete]
2763 ## Start Addr = 0x00000000
2766 You can check the success of the download using the 'iminfo' command;
2767 this includes a checksum verification so you can be sure no data
2768 corruption happened:
2772 ## Checking Image at 40100000 ...
2773 Image Name: 2.2.13 for initrd on TQM850L
2774 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2775 Data Size: 335725 Bytes = 327 kB = 0 MB
2776 Load Address: 00000000
2777 Entry Point: 0000000c
2778 Verifying Checksum ... OK
2784 The "bootm" command is used to boot an application that is stored in
2785 memory (RAM or Flash). In case of a Linux kernel image, the contents
2786 of the "bootargs" environment variable is passed to the kernel as
2787 parameters. You can check and modify this variable using the
2788 "printenv" and "setenv" commands:
2791 => printenv bootargs
2792 bootargs=root=/dev/ram
2794 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2796 => printenv bootargs
2797 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2800 ## Booting Linux kernel at 40020000 ...
2801 Image Name: 2.2.13 for NFS on TQM850L
2802 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2803 Data Size: 381681 Bytes = 372 kB = 0 MB
2804 Load Address: 00000000
2805 Entry Point: 0000000c
2806 Verifying Checksum ... OK
2807 Uncompressing Kernel Image ... OK
2808 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2809 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2810 time_init: decrementer frequency = 187500000/60
2811 Calibrating delay loop... 49.77 BogoMIPS
2812 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2815 If you want to boot a Linux kernel with initial ram disk, you pass
2816 the memory addresses of both the kernel and the initrd image (PPBCOOT
2817 format!) to the "bootm" command:
2819 => imi 40100000 40200000
2821 ## Checking Image at 40100000 ...
2822 Image Name: 2.2.13 for initrd on TQM850L
2823 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2824 Data Size: 335725 Bytes = 327 kB = 0 MB
2825 Load Address: 00000000
2826 Entry Point: 0000000c
2827 Verifying Checksum ... OK
2829 ## Checking Image at 40200000 ...
2830 Image Name: Simple Ramdisk Image
2831 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2832 Data Size: 566530 Bytes = 553 kB = 0 MB
2833 Load Address: 00000000
2834 Entry Point: 00000000
2835 Verifying Checksum ... OK
2837 => bootm 40100000 40200000
2838 ## Booting Linux kernel at 40100000 ...
2839 Image Name: 2.2.13 for initrd on TQM850L
2840 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2841 Data Size: 335725 Bytes = 327 kB = 0 MB
2842 Load Address: 00000000
2843 Entry Point: 0000000c
2844 Verifying Checksum ... OK
2845 Uncompressing Kernel Image ... OK
2846 ## Loading RAMDisk Image at 40200000 ...
2847 Image Name: Simple Ramdisk Image
2848 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2849 Data Size: 566530 Bytes = 553 kB = 0 MB
2850 Load Address: 00000000
2851 Entry Point: 00000000
2852 Verifying Checksum ... OK
2853 Loading Ramdisk ... OK
2854 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2855 Boot arguments: root=/dev/ram
2856 time_init: decrementer frequency = 187500000/60
2857 Calibrating delay loop... 49.77 BogoMIPS
2859 RAMDISK: Compressed image found at block 0
2860 VFS: Mounted root (ext2 filesystem).
2864 More About U-Boot Image Types:
2865 ------------------------------
2867 U-Boot supports the following image types:
2869 "Standalone Programs" are directly runnable in the environment
2870 provided by U-Boot; it is expected that (if they behave
2871 well) you can continue to work in U-Boot after return from
2872 the Standalone Program.
2873 "OS Kernel Images" are usually images of some Embedded OS which
2874 will take over control completely. Usually these programs
2875 will install their own set of exception handlers, device
2876 drivers, set up the MMU, etc. - this means, that you cannot
2877 expect to re-enter U-Boot except by resetting the CPU.
2878 "RAMDisk Images" are more or less just data blocks, and their
2879 parameters (address, size) are passed to an OS kernel that is
2881 "Multi-File Images" contain several images, typically an OS
2882 (Linux) kernel image and one or more data images like
2883 RAMDisks. This construct is useful for instance when you want
2884 to boot over the network using BOOTP etc., where the boot
2885 server provides just a single image file, but you want to get
2886 for instance an OS kernel and a RAMDisk image.
2888 "Multi-File Images" start with a list of image sizes, each
2889 image size (in bytes) specified by an "uint32_t" in network
2890 byte order. This list is terminated by an "(uint32_t)0".
2891 Immediately after the terminating 0 follow the images, one by
2892 one, all aligned on "uint32_t" boundaries (size rounded up to
2893 a multiple of 4 bytes).
2895 "Firmware Images" are binary images containing firmware (like
2896 U-Boot or FPGA images) which usually will be programmed to
2899 "Script files" are command sequences that will be executed by
2900 U-Boot's command interpreter; this feature is especially
2901 useful when you configure U-Boot to use a real shell (hush)
2902 as command interpreter.
2908 One of the features of U-Boot is that you can dynamically load and
2909 run "standalone" applications, which can use some resources of
2910 U-Boot like console I/O functions or interrupt services.
2912 Two simple examples are included with the sources:
2917 'examples/hello_world.c' contains a small "Hello World" Demo
2918 application; it is automatically compiled when you build U-Boot.
2919 It's configured to run at address 0x00040004, so you can play with it
2923 ## Ready for S-Record download ...
2924 ~>examples/hello_world.srec
2925 1 2 3 4 5 6 7 8 9 10 11 ...
2926 [file transfer complete]
2928 ## Start Addr = 0x00040004
2930 => go 40004 Hello World! This is a test.
2931 ## Starting application at 0x00040004 ...
2942 Hit any key to exit ...
2944 ## Application terminated, rc = 0x0
2946 Another example, which demonstrates how to register a CPM interrupt
2947 handler with the U-Boot code, can be found in 'examples/timer.c'.
2948 Here, a CPM timer is set up to generate an interrupt every second.
2949 The interrupt service routine is trivial, just printing a '.'
2950 character, but this is just a demo program. The application can be
2951 controlled by the following keys:
2953 ? - print current values og the CPM Timer registers
2954 b - enable interrupts and start timer
2955 e - stop timer and disable interrupts
2956 q - quit application
2959 ## Ready for S-Record download ...
2960 ~>examples/timer.srec
2961 1 2 3 4 5 6 7 8 9 10 11 ...
2962 [file transfer complete]
2964 ## Start Addr = 0x00040004
2967 ## Starting application at 0x00040004 ...
2970 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
2973 [q, b, e, ?] Set interval 1000000 us
2976 [q, b, e, ?] ........
2977 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
2980 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
2983 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
2986 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
2988 [q, b, e, ?] ...Stopping timer
2990 [q, b, e, ?] ## Application terminated, rc = 0x0
2996 Over time, many people have reported problems when trying to use the
2997 "minicom" terminal emulation program for serial download. I (wd)
2998 consider minicom to be broken, and recommend not to use it. Under
2999 Unix, I recommend to use C-Kermit for general purpose use (and
3000 especially for kermit binary protocol download ("loadb" command), and
3001 use "cu" for S-Record download ("loads" command).
3003 Nevertheless, if you absolutely want to use it try adding this
3004 configuration to your "File transfer protocols" section:
3006 Name Program Name U/D FullScr IO-Red. Multi
3007 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3008 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3014 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3015 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3017 Building requires a cross environment; it is known to work on
3018 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3019 need gmake since the Makefiles are not compatible with BSD make).
3020 Note that the cross-powerpc package does not install include files;
3021 attempting to build U-Boot will fail because <machine/ansi.h> is
3022 missing. This file has to be installed and patched manually:
3024 # cd /usr/pkg/cross/powerpc-netbsd/include
3026 # ln -s powerpc machine
3027 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3028 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3030 Native builds *don't* work due to incompatibilities between native
3031 and U-Boot include files.
3033 Booting assumes that (the first part of) the image booted is a
3034 stage-2 loader which in turn loads and then invokes the kernel
3035 proper. Loader sources will eventually appear in the NetBSD source
3036 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3037 meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
3041 Implementation Internals:
3042 =========================
3044 The following is not intended to be a complete description of every
3045 implementation detail. However, it should help to understand the
3046 inner workings of U-Boot and make it easier to port it to custom
3050 Initial Stack, Global Data:
3051 ---------------------------
3053 The implementation of U-Boot is complicated by the fact that U-Boot
3054 starts running out of ROM (flash memory), usually without access to
3055 system RAM (because the memory controller is not initialized yet).
3056 This means that we don't have writable Data or BSS segments, and BSS
3057 is not initialized as zero. To be able to get a C environment working
3058 at all, we have to allocate at least a minimal stack. Implementation
3059 options for this are defined and restricted by the CPU used: Some CPU
3060 models provide on-chip memory (like the IMMR area on MPC8xx and
3061 MPC826x processors), on others (parts of) the data cache can be
3062 locked as (mis-) used as memory, etc.
3064 Chris Hallinan posted a good summary of these issues to the
3065 u-boot-users mailing list:
3067 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3068 From: "Chris Hallinan" <clh@net1plus.com>
3069 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3072 Correct me if I'm wrong, folks, but the way I understand it
3073 is this: Using DCACHE as initial RAM for Stack, etc, does not
3074 require any physical RAM backing up the cache. The cleverness
3075 is that the cache is being used as a temporary supply of
3076 necessary storage before the SDRAM controller is setup. It's
3077 beyond the scope of this list to expain the details, but you
3078 can see how this works by studying the cache architecture and
3079 operation in the architecture and processor-specific manuals.
3081 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3082 is another option for the system designer to use as an
3083 initial stack/ram area prior to SDRAM being available. Either
3084 option should work for you. Using CS 4 should be fine if your
3085 board designers haven't used it for something that would
3086 cause you grief during the initial boot! It is frequently not
3089 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
3090 with your processor/board/system design. The default value
3091 you will find in any recent u-boot distribution in
3092 Walnut405.h should work for you. I'd set it to a value larger
3093 than your SDRAM module. If you have a 64MB SDRAM module, set
3094 it above 400_0000. Just make sure your board has no resources
3095 that are supposed to respond to that address! That code in
3096 start.S has been around a while and should work as is when
3097 you get the config right.
3102 It is essential to remember this, since it has some impact on the C
3103 code for the initialization procedures:
3105 * Initialized global data (data segment) is read-only. Do not attempt
3108 * Do not use any unitialized global data (or implicitely initialized
3109 as zero data - BSS segment) at all - this is undefined, initiali-
3110 zation is performed later (when relocating to RAM).
3112 * Stack space is very limited. Avoid big data buffers or things like
3115 Having only the stack as writable memory limits means we cannot use
3116 normal global data to share information beween the code. But it
3117 turned out that the implementation of U-Boot can be greatly
3118 simplified by making a global data structure (gd_t) available to all
3119 functions. We could pass a pointer to this data as argument to _all_
3120 functions, but this would bloat the code. Instead we use a feature of
3121 the GCC compiler (Global Register Variables) to share the data: we
3122 place a pointer (gd) to the global data into a register which we
3123 reserve for this purpose.
3125 When choosing a register for such a purpose we are restricted by the
3126 relevant (E)ABI specifications for the current architecture, and by
3127 GCC's implementation.
3129 For PowerPC, the following registers have specific use:
3132 R3-R4: parameter passing and return values
3133 R5-R10: parameter passing
3134 R13: small data area pointer
3138 (U-Boot also uses R14 as internal GOT pointer.)
3140 ==> U-Boot will use R29 to hold a pointer to the global data
3142 Note: on PPC, we could use a static initializer (since the
3143 address of the global data structure is known at compile time),
3144 but it turned out that reserving a register results in somewhat
3145 smaller code - although the code savings are not that big (on
3146 average for all boards 752 bytes for the whole U-Boot image,
3147 624 text + 127 data).
3149 On ARM, the following registers are used:
3151 R0: function argument word/integer result
3152 R1-R3: function argument word
3154 R10: stack limit (used only if stack checking if enabled)
3155 R11: argument (frame) pointer
3156 R12: temporary workspace
3159 R15: program counter
3161 ==> U-Boot will use R8 to hold a pointer to the global data
3167 U-Boot runs in system state and uses physical addresses, i.e. the
3168 MMU is not used either for address mapping nor for memory protection.
3170 The available memory is mapped to fixed addresses using the memory
3171 controller. In this process, a contiguous block is formed for each
3172 memory type (Flash, SDRAM, SRAM), even when it consists of several
3173 physical memory banks.
3175 U-Boot is installed in the first 128 kB of the first Flash bank (on
3176 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3177 booting and sizing and initializing DRAM, the code relocates itself
3178 to the upper end of DRAM. Immediately below the U-Boot code some
3179 memory is reserved for use by malloc() [see CFG_MALLOC_LEN
3180 configuration setting]. Below that, a structure with global Board
3181 Info data is placed, followed by the stack (growing downward).
3183 Additionally, some exception handler code is copied to the low 8 kB
3184 of DRAM (0x00000000 ... 0x00001FFF).
3186 So a typical memory configuration with 16 MB of DRAM could look like
3189 0x0000 0000 Exception Vector code
3192 0x0000 2000 Free for Application Use
3198 0x00FB FF20 Monitor Stack (Growing downward)
3199 0x00FB FFAC Board Info Data and permanent copy of global data
3200 0x00FC 0000 Malloc Arena
3203 0x00FE 0000 RAM Copy of Monitor Code
3204 ... eventually: LCD or video framebuffer
3205 ... eventually: pRAM (Protected RAM - unchanged by reset)
3206 0x00FF FFFF [End of RAM]
3209 System Initialization:
3210 ----------------------
3212 In the reset configuration, U-Boot starts at the reset entry point
3213 (on most PowerPC systens at address 0x00000100). Because of the reset
3214 configuration for CS0# this is a mirror of the onboard Flash memory.
3215 To be able to re-map memory U-Boot then jumps to its link address.
3216 To be able to implement the initialization code in C, a (small!)
3217 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3218 which provide such a feature like MPC8xx or MPC8260), or in a locked
3219 part of the data cache. After that, U-Boot initializes the CPU core,
3220 the caches and the SIU.
3222 Next, all (potentially) available memory banks are mapped using a
3223 preliminary mapping. For example, we put them on 512 MB boundaries
3224 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3225 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3226 programmed for SDRAM access. Using the temporary configuration, a
3227 simple memory test is run that determines the size of the SDRAM
3230 When there is more than one SDRAM bank, and the banks are of
3231 different size, the largest is mapped first. For equal size, the first
3232 bank (CS2#) is mapped first. The first mapping is always for address
3233 0x00000000, with any additional banks following immediately to create
3234 contiguous memory starting from 0.
3236 Then, the monitor installs itself at the upper end of the SDRAM area
3237 and allocates memory for use by malloc() and for the global Board
3238 Info data; also, the exception vector code is copied to the low RAM
3239 pages, and the final stack is set up.
3241 Only after this relocation will you have a "normal" C environment;
3242 until that you are restricted in several ways, mostly because you are
3243 running from ROM, and because the code will have to be relocated to a
3247 U-Boot Porting Guide:
3248 ----------------------
3250 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3254 int main (int argc, char *argv[])
3256 sighandler_t no_more_time;
3258 signal (SIGALRM, no_more_time);
3259 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3261 if (available_money > available_manpower) {
3262 pay consultant to port U-Boot;
3266 Download latest U-Boot source;
3268 Subscribe to u-boot-users mailing list;
3271 email ("Hi, I am new to U-Boot, how do I get started?");
3275 Read the README file in the top level directory;
3276 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3277 Read the source, Luke;
3280 if (available_money > toLocalCurrency ($2500)) {
3283 Add a lot of aggravation and time;
3286 Create your own board support subdirectory;
3288 Create your own board config file;
3292 Add / modify source code;
3296 email ("Hi, I am having problems...");
3298 Send patch file to Wolfgang;
3303 void no_more_time (int sig)
3312 All contributions to U-Boot should conform to the Linux kernel
3313 coding style; see the file "Documentation/CodingStyle" in your Linux
3314 kernel source directory.
3316 Please note that U-Boot is implemented in C (and to some small parts
3317 in Assembler); no C++ is used, so please do not use C++ style
3318 comments (//) in your code.
3320 Please also stick to the following formatting rules:
3321 - remove any trailing white space
3322 - use TAB characters for indentation, not spaces
3323 - make sure NOT to use DOS '\r\n' line feeds
3324 - do not add more than 2 empty lines to source files
3325 - do not add trailing empty lines to source files
3327 Submissions which do not conform to the standards may be returned
3328 with a request to reformat the changes.
3334 Since the number of patches for U-Boot is growing, we need to
3335 establish some rules. Submissions which do not conform to these rules
3336 may be rejected, even when they contain important and valuable stuff.
3339 When you send a patch, please include the following information with
3342 * For bug fixes: a description of the bug and how your patch fixes
3343 this bug. Please try to include a way of demonstrating that the
3344 patch actually fixes something.
3346 * For new features: a description of the feature and your
3349 * A CHANGELOG entry as plaintext (separate from the patch)
3351 * For major contributions, your entry to the CREDITS file
3353 * When you add support for a new board, don't forget to add this
3354 board to the MAKEALL script, too.
3356 * If your patch adds new configuration options, don't forget to
3357 document these in the README file.
3359 * The patch itself. If you are accessing the CVS repository use "cvs
3360 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3361 version of diff does not support these options, then get the latest
3362 version of GNU diff.
3364 The current directory when running this command shall be the top
3365 level directory of the U-Boot source tree, or it's parent directory
3366 (i. e. please make sure that your patch includes sufficient
3367 directory information for the affected files).
3369 We accept patches as plain text, MIME attachments or as uuencoded
3372 * If one logical set of modifications affects or creates several
3373 files, all these changes shall be submitted in a SINGLE patch file.
3375 * Changesets that contain different, unrelated modifications shall be
3376 submitted as SEPARATE patches, one patch per changeset.
3381 * Before sending the patch, run the MAKEALL script on your patched
3382 source tree and make sure that no errors or warnings are reported
3383 for any of the boards.
3385 * Keep your modifications to the necessary minimum: A patch
3386 containing several unrelated changes or arbitrary reformats will be
3387 returned with a request to re-formatting / split it.
3389 * If you modify existing code, make sure that your new code does not
3390 add to the memory footprint of the code ;-) Small is beautiful!
3391 When adding new features, these should compile conditionally only
3392 (using #ifdef), and the resulting code with the new feature
3393 disabled must not need more memory than the old code without your