2 # (C) Copyright 2000 - 2004
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC and ARM processors, which can be
29 installed in a boot ROM and used to initialize and test the hardware
30 or to download and run application code.
32 The development of U-Boot is closely related to Linux: some parts of
33 the source code originate in the Linux source tree, we have some
34 header files in common, and special provision has been made to
35 support booting of Linux images.
37 Some attention has been paid to make this software easily
38 configurable and extendable. For instance, all monitor commands are
39 implemented with the same call interface, so that it's very easy to
40 add new commands. Also, instead of permanently adding rarely used
41 code (for instance hardware test utilities) to the monitor, you can
42 load and run it dynamically.
48 In general, all boards for which a configuration option exists in the
49 Makefile have been tested to some extent and can be considered
50 "working". In fact, many of them are used in production systems.
52 In case of problems see the CHANGELOG and CREDITS files to find out
53 who contributed the specific port.
59 In case you have questions about, problems with or contributions for
60 U-Boot you should send a message to the U-Boot mailing list at
61 <u-boot-users@lists.sourceforge.net>. There is also an archive of
62 previous traffic on the mailing list - please search the archive
63 before asking FAQ's. Please see
64 http://lists.sourceforge.net/lists/listinfo/u-boot-users/
70 - start from 8xxrom sources
71 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
73 - make it easier to add custom boards
74 - make it possible to add other [PowerPC] CPUs
75 - extend functions, especially:
76 * Provide extended interface to Linux boot loader
79 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
80 - create ARMBoot project (http://sourceforge.net/projects/armboot)
81 - add other CPU families (starting with ARM)
82 - create U-Boot project (http://sourceforge.net/projects/u-boot)
88 The "official" name of this project is "Das U-Boot". The spelling
89 "U-Boot" shall be used in all written text (documentation, comments
90 in source files etc.). Example:
92 This is the README file for the U-Boot project.
94 File names etc. shall be based on the string "u-boot". Examples:
96 include/asm-ppc/u-boot.h
98 #include <asm/u-boot.h>
100 Variable names, preprocessor constants etc. shall be either based on
101 the string "u_boot" or on "U_BOOT". Example:
103 U_BOOT_VERSION u_boot_logo
104 IH_OS_U_BOOT u_boot_hush_start
110 U-Boot uses a 3 level version number containing a version, a
111 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
112 sub-version "34", and patchlevel "4".
114 The patchlevel is used to indicate certain stages of development
115 between released versions, i. e. officially released versions of
116 U-Boot will always have a patchlevel of "0".
122 - board Board dependent files
123 - common Misc architecture independent functions
124 - cpu CPU specific files
125 - 74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
126 - arm720t Files specific to ARM 720 CPUs
127 - arm920t Files specific to ARM 920 CPUs
128 - arm925t Files specific to ARM 925 CPUs
129 - arm926ejs Files specific to ARM 926 CPUs
130 - at91rm9200 Files specific to Atmel AT91RM9200 CPUs
131 - i386 Files specific to i386 CPUs
132 - ixp Files specific to Intel XScale IXP CPUs
133 - mcf52x2 Files specific to Motorola ColdFire MCF52x2 CPUs
134 - mips Files specific to MIPS CPUs
135 - mpc5xx Files specific to Motorola MPC5xx CPUs
136 - mpc5xxx Files specific to Motorola MPC5xxx CPUs
137 - mpc8xx Files specific to Motorola MPC8xx CPUs
138 - mpc824x Files specific to Motorola MPC824x CPUs
139 - mpc8260 Files specific to Motorola MPC8260 CPUs
140 - mpc85xx Files specific to Motorola MPC85xx CPUs
141 - nios Files specific to Altera NIOS CPUs
142 - ppc4xx Files specific to IBM PowerPC 4xx CPUs
143 - pxa Files specific to Intel XScale PXA CPUs
144 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
145 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
146 - disk Code for disk drive partition handling
147 - doc Documentation (don't expect too much)
148 - drivers Commonly used device drivers
149 - dtt Digital Thermometer and Thermostat drivers
150 - examples Example code for standalone applications, etc.
151 - include Header Files
152 - lib_arm Files generic to ARM architecture
153 - lib_generic Files generic to all architectures
154 - lib_i386 Files generic to i386 architecture
155 - lib_m68k Files generic to m68k architecture
156 - lib_mips Files generic to MIPS architecture
157 - lib_nios Files generic to NIOS architecture
158 - lib_ppc Files generic to PowerPC architecture
159 - net Networking code
160 - post Power On Self Test
161 - rtc Real Time Clock drivers
162 - tools Tools to build S-Record or U-Boot images, etc.
164 Software Configuration:
165 =======================
167 Configuration is usually done using C preprocessor defines; the
168 rationale behind that is to avoid dead code whenever possible.
170 There are two classes of configuration variables:
172 * Configuration _OPTIONS_:
173 These are selectable by the user and have names beginning with
176 * Configuration _SETTINGS_:
177 These depend on the hardware etc. and should not be meddled with if
178 you don't know what you're doing; they have names beginning with
181 Later we will add a configuration tool - probably similar to or even
182 identical to what's used for the Linux kernel. Right now, we have to
183 do the configuration by hand, which means creating some symbolic
184 links and editing some configuration files. We use the TQM8xxL boards
188 Selection of Processor Architecture and Board Type:
189 ---------------------------------------------------
191 For all supported boards there are ready-to-use default
192 configurations available; just type "make <board_name>_config".
194 Example: For a TQM823L module type:
199 For the Cogent platform, you need to specify the cpu type as well;
200 e.g. "make cogent_mpc8xx_config". And also configure the cogent
201 directory according to the instructions in cogent/README.
204 Configuration Options:
205 ----------------------
207 Configuration depends on the combination of board and CPU type; all
208 such information is kept in a configuration file
209 "include/configs/<board_name>.h".
211 Example: For a TQM823L module, all configuration settings are in
212 "include/configs/TQM823L.h".
215 Many of the options are named exactly as the corresponding Linux
216 kernel configuration options. The intention is to make it easier to
217 build a config tool - later.
220 The following options need to be configured:
222 - CPU Type: Define exactly one of
226 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
228 or CONFIG_MPC824X, CONFIG_MPC8260
243 MicroBlaze based CPUs:
244 ----------------------
248 - Board Type: Define exactly one of
250 PowerPC based boards:
251 ---------------------
253 CONFIG_ADCIOP CONFIG_GEN860T CONFIG_PCI405
254 CONFIG_ADS860 CONFIG_GENIETV CONFIG_PCIPPC2
255 CONFIG_AMX860 CONFIG_GTH CONFIG_PCIPPC6
256 CONFIG_AR405 CONFIG_gw8260 CONFIG_pcu_e
257 CONFIG_BAB7xx CONFIG_hermes CONFIG_PIP405
258 CONFIG_c2mon CONFIG_hymod CONFIG_PM826
259 CONFIG_CANBT CONFIG_IAD210 CONFIG_ppmc8260
260 CONFIG_CCM CONFIG_ICU862 CONFIG_QS823
261 CONFIG_CMI CONFIG_IP860 CONFIG_QS850
262 CONFIG_cogent_mpc8260 CONFIG_IPHASE4539 CONFIG_QS860T
263 CONFIG_cogent_mpc8xx CONFIG_IVML24 CONFIG_RBC823
264 CONFIG_CPCI405 CONFIG_IVML24_128 CONFIG_RPXClassic
265 CONFIG_CPCI4052 CONFIG_IVML24_256 CONFIG_RPXlite
266 CONFIG_CPCIISER4 CONFIG_IVMS8 CONFIG_RPXsuper
267 CONFIG_CPU86 CONFIG_IVMS8_128 CONFIG_rsdproto
268 CONFIG_CRAYL1 CONFIG_IVMS8_256 CONFIG_sacsng
269 CONFIG_CSB272 CONFIG_JSE CONFIG_Sandpoint8240
270 CONFIG_CU824 CONFIG_LANTEC CONFIG_Sandpoint8245
271 CONFIG_DASA_SIM CONFIG_lwmon CONFIG_sbc8260
272 CONFIG_DB64360 CONFIG_MBX CONFIG_sbc8560
273 CONFIG_DB64460 CONFIG_MBX860T CONFIG_SM850
274 CONFIG_DU405 CONFIG_MHPC CONFIG_SPD823TS
275 CONFIG_DUET_ADS CONFIG_MIP405 CONFIG_STXGP3
276 CONFIG_EBONY CONFIG_MOUSSE CONFIG_SXNI855T
277 CONFIG_ELPPC CONFIG_MPC8260ADS CONFIG_TQM823L
278 CONFIG_ELPT860 CONFIG_MPC8540ADS CONFIG_TQM8260
279 CONFIG_ep8260 CONFIG_MPC8560ADS CONFIG_TQM850L
280 CONFIG_ERIC CONFIG_MUSENKI CONFIG_TQM855L
281 CONFIG_ESTEEM192E CONFIG_MVS1 CONFIG_TQM860L
282 CONFIG_ETX094 CONFIG_NETPHONE CONFIG_TTTech
283 CONFIG_EVB64260 CONFIG_NETTA CONFIG_UTX8245
284 CONFIG_FADS823 CONFIG_NETVIA CONFIG_V37
285 CONFIG_FADS850SAR CONFIG_NX823 CONFIG_W7OLMC
286 CONFIG_FADS860T CONFIG_OCRTC CONFIG_W7OLMG
287 CONFIG_FLAGADM CONFIG_ORSG CONFIG_WALNUT405
288 CONFIG_FPS850L CONFIG_OXC CONFIG_ZPC1900
289 CONFIG_FPS860L CONFIG_ZUMA
294 CONFIG_AT91RM9200DK, CONFIG_CERF250, CONFIG_DNP1110,
295 CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
296 CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
297 CONFIG_LART, CONFIG_LPD7A400 CONFIG_LUBBOCK,
298 CONFIG_OSK_OMAP5912, CONFIG_SHANNON, CONFIG_P2_OMAP730,
299 CONFIG_SMDK2400, CONFIG_SMDK2410, CONFIG_TRAB,
302 MicroBlaze based boards:
303 ------------------------
308 - CPU Module Type: (if CONFIG_COGENT is defined)
309 Define exactly one of
311 --- FIXME --- not tested yet:
312 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
313 CONFIG_CMA287_23, CONFIG_CMA287_50
315 - Motherboard Type: (if CONFIG_COGENT is defined)
316 Define exactly one of
317 CONFIG_CMA101, CONFIG_CMA102
319 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
320 Define one or more of
323 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
324 Define one or more of
325 CONFIG_LCD_HEARTBEAT - update a character position on
326 the lcd display every second with
329 - Board flavour: (if CONFIG_MPC8260ADS is defined)
332 CFG_8260ADS - original MPC8260ADS
333 CFG_8266ADS - MPC8266ADS
334 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
335 CFG_8272ADS - MPC8272ADS
337 - MPC824X Family Member (if CONFIG_MPC824X is defined)
338 Define exactly one of
339 CONFIG_MPC8240, CONFIG_MPC8245
341 - 8xx CPU Options: (if using an MPC8xx cpu)
342 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
343 get_gclk_freq() cannot work
344 e.g. if there is no 32KHz
345 reference PIT/RTC clock
346 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
349 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
352 CONFIG_8xx_CPUCLK_DEFAULT
353 See doc/README.MPC866
357 Define this to measure the actual CPU clock instead
358 of relying on the correctness of the configured
359 values. Mostly useful for board bringup to make sure
360 the PLL is locked at the intended frequency. Note
361 that this requires a (stable) reference clock (32 kHz
362 RTC clock or CFG_8XX_XIN)
364 - Linux Kernel Interface:
367 U-Boot stores all clock information in Hz
368 internally. For binary compatibility with older Linux
369 kernels (which expect the clocks passed in the
370 bd_info data to be in MHz) the environment variable
371 "clocks_in_mhz" can be defined so that U-Boot
372 converts clock data to MHZ before passing it to the
374 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
375 "clocks_in_mhz=1" is automatically included in the
378 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
380 When transfering memsize parameter to linux, some versions
381 expect it to be in bytes, others in MB.
382 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
387 Define this if you want support for Amba PrimeCell PL010 UARTs.
391 Define this if you want support for Amba PrimeCell PL011 UARTs.
395 If you have Amba PrimeCell PL011 UARTs, set this variable to
396 the clock speed of the UARTs.
400 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
401 define this to a list of base addresses for each (supported)
402 port. See e.g. include/configs/versatile.h
406 Depending on board, define exactly one serial port
407 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
408 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
409 console by defining CONFIG_8xx_CONS_NONE
411 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
412 port routines must be defined elsewhere
413 (i.e. serial_init(), serial_getc(), ...)
416 Enables console device for a color framebuffer. Needs following
417 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
418 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
420 VIDEO_HW_RECTFILL graphic chip supports
423 VIDEO_HW_BITBLT graphic chip supports
424 bit-blit (cf. smiLynxEM)
425 VIDEO_VISIBLE_COLS visible pixel columns
427 VIDEO_VISIBLE_ROWS visible pixel rows
428 VIDEO_PIXEL_SIZE bytes per pixel
429 VIDEO_DATA_FORMAT graphic data format
430 (0-5, cf. cfb_console.c)
431 VIDEO_FB_ADRS framebuffer address
432 VIDEO_KBD_INIT_FCT keyboard int fct
433 (i.e. i8042_kbd_init())
434 VIDEO_TSTC_FCT test char fct
436 VIDEO_GETC_FCT get char fct
438 CONFIG_CONSOLE_CURSOR cursor drawing on/off
439 (requires blink timer
441 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
442 CONFIG_CONSOLE_TIME display time/date info in
444 (requires CFG_CMD_DATE)
445 CONFIG_VIDEO_LOGO display Linux logo in
447 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
448 linux_logo.h for logo.
449 Requires CONFIG_VIDEO_LOGO
450 CONFIG_CONSOLE_EXTRA_INFO
451 addional board info beside
454 When CONFIG_CFB_CONSOLE is defined, video console is
455 default i/o. Serial console can be forced with
456 environment 'console=serial'.
458 When CONFIG_SILENT_CONSOLE is defined, all console
459 messages (by U-Boot and Linux!) can be silenced with
460 the "silent" environment variable. See
461 doc/README.silent for more information.
464 CONFIG_BAUDRATE - in bps
465 Select one of the baudrates listed in
466 CFG_BAUDRATE_TABLE, see below.
467 CFG_BRGCLK_PRESCALE, baudrate prescale
469 - Interrupt driven serial port input:
470 CONFIG_SERIAL_SOFTWARE_FIFO
473 Use an interrupt handler for receiving data on the
474 serial port. It also enables using hardware handshake
475 (RTS/CTS) and UART's built-in FIFO. Set the number of
476 bytes the interrupt driven input buffer should have.
478 Leave undefined to disable this feature, including
479 disable the buffer and hardware handshake.
481 - Console UART Number:
485 If defined internal UART1 (and not UART0) is used
486 as default U-Boot console.
488 - Boot Delay: CONFIG_BOOTDELAY - in seconds
489 Delay before automatically booting the default image;
490 set to -1 to disable autoboot.
492 See doc/README.autoboot for these options that
493 work with CONFIG_BOOTDELAY. None are required.
494 CONFIG_BOOT_RETRY_TIME
495 CONFIG_BOOT_RETRY_MIN
496 CONFIG_AUTOBOOT_KEYED
497 CONFIG_AUTOBOOT_PROMPT
498 CONFIG_AUTOBOOT_DELAY_STR
499 CONFIG_AUTOBOOT_STOP_STR
500 CONFIG_AUTOBOOT_DELAY_STR2
501 CONFIG_AUTOBOOT_STOP_STR2
502 CONFIG_ZERO_BOOTDELAY_CHECK
503 CONFIG_RESET_TO_RETRY
507 Only needed when CONFIG_BOOTDELAY is enabled;
508 define a command string that is automatically executed
509 when no character is read on the console interface
510 within "Boot Delay" after reset.
513 This can be used to pass arguments to the bootm
514 command. The value of CONFIG_BOOTARGS goes into the
515 environment value "bootargs".
517 CONFIG_RAMBOOT and CONFIG_NFSBOOT
518 The value of these goes into the environment as
519 "ramboot" and "nfsboot" respectively, and can be used
520 as a convenience, when switching between booting from
526 When this option is #defined, the existence of the
527 environment variable "preboot" will be checked
528 immediately before starting the CONFIG_BOOTDELAY
529 countdown and/or running the auto-boot command resp.
530 entering interactive mode.
532 This feature is especially useful when "preboot" is
533 automatically generated or modified. For an example
534 see the LWMON board specific code: here "preboot" is
535 modified when the user holds down a certain
536 combination of keys on the (special) keyboard when
539 - Serial Download Echo Mode:
541 If defined to 1, all characters received during a
542 serial download (using the "loads" command) are
543 echoed back. This might be needed by some terminal
544 emulations (like "cu"), but may as well just take
545 time on others. This setting #define's the initial
546 value of the "loads_echo" environment variable.
548 - Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
550 Select one of the baudrates listed in
551 CFG_BAUDRATE_TABLE, see below.
555 Most monitor functions can be selected (or
556 de-selected) by adjusting the definition of
557 CONFIG_COMMANDS; to select individual functions,
558 #define CONFIG_COMMANDS by "OR"ing any of the
561 #define enables commands:
562 -------------------------
563 CFG_CMD_ASKENV * ask for env variable
564 CFG_CMD_AUTOSCRIPT Autoscript Support
566 CFG_CMD_BEDBUG * Include BedBug Debugger
567 CFG_CMD_BMP * BMP support
568 CFG_CMD_BSP * Board specific commands
570 CFG_CMD_CACHE * icache, dcache
571 CFG_CMD_CONSOLE coninfo
572 CFG_CMD_DATE * support for RTC, date/time...
573 CFG_CMD_DHCP * DHCP support
574 CFG_CMD_DIAG * Diagnostics
575 CFG_CMD_DOC * Disk-On-Chip Support
576 CFG_CMD_DTT * Digital Therm and Thermostat
577 CFG_CMD_ECHO * echo arguments
578 CFG_CMD_EEPROM * EEPROM read/write support
579 CFG_CMD_ELF * bootelf, bootvx
581 CFG_CMD_FDC * Floppy Disk Support
582 CFG_CMD_FAT * FAT partition support
583 CFG_CMD_FDOS * Dos diskette Support
584 CFG_CMD_FLASH flinfo, erase, protect
585 CFG_CMD_FPGA FPGA device initialization support
586 CFG_CMD_HWFLOW * RTS/CTS hw flow control
587 CFG_CMD_I2C * I2C serial bus support
588 CFG_CMD_IDE * IDE harddisk support
590 CFG_CMD_IMLS List all found images
591 CFG_CMD_IMMAP * IMMR dump support
592 CFG_CMD_IRQ * irqinfo
593 CFG_CMD_ITEST Integer/string test of 2 values
594 CFG_CMD_JFFS2 * JFFS2 Support
598 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
600 CFG_CMD_MISC Misc functions like sleep etc
601 CFG_CMD_MMC * MMC memory mapped support
602 CFG_CMD_MII * MII utility commands
603 CFG_CMD_NAND * NAND support
604 CFG_CMD_NET bootp, tftpboot, rarpboot
605 CFG_CMD_PCI * pciinfo
606 CFG_CMD_PCMCIA * PCMCIA support
607 CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
608 CFG_CMD_PORTIO * Port I/O
609 CFG_CMD_REGINFO * Register dump
610 CFG_CMD_RUN run command in env variable
611 CFG_CMD_SAVES * save S record dump
612 CFG_CMD_SCSI * SCSI Support
613 CFG_CMD_SDRAM * print SDRAM configuration information
614 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
615 CFG_CMD_SPI * SPI serial bus support
616 CFG_CMD_USB * USB support
617 CFG_CMD_VFD * VFD support (TRAB)
618 CFG_CMD_BSP * Board SPecific functions
619 CFG_CMD_CDP * Cisco Discover Protocol support
620 -----------------------------------------------
623 CONFIG_CMD_DFL Default configuration; at the moment
624 this is includes all commands, except
625 the ones marked with "*" in the list
628 If you don't define CONFIG_COMMANDS it defaults to
629 CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
630 override the default settings in the respective
633 EXAMPLE: If you want all functions except of network
634 support you can write:
636 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
639 Note: Don't enable the "icache" and "dcache" commands
640 (configuration option CFG_CMD_CACHE) unless you know
641 what you (and your U-Boot users) are doing. Data
642 cache cannot be enabled on systems like the 8xx or
643 8260 (where accesses to the IMMR region must be
644 uncached), and it cannot be disabled on all other
645 systems where we (mis-) use the data cache to hold an
646 initial stack and some data.
649 XXX - this list needs to get updated!
653 If this variable is defined, it enables watchdog
654 support. There must be support in the platform specific
655 code for a watchdog. For the 8xx and 8260 CPUs, the
656 SIU Watchdog feature is enabled in the SYPCR
660 CONFIG_VERSION_VARIABLE
661 If this variable is defined, an environment variable
662 named "ver" is created by U-Boot showing the U-Boot
663 version as printed by the "version" command.
664 This variable is readonly.
668 When CFG_CMD_DATE is selected, the type of the RTC
669 has to be selected, too. Define exactly one of the
672 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
673 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
674 CONFIG_RTC_MC146818 - use MC146818 RTC
675 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
676 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
677 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
678 CONFIG_RTC_DS164x - use Dallas DS164x RTC
679 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
681 Note that if the RTC uses I2C, then the I2C interface
682 must also be configured. See I2C Support, below.
686 When CONFIG_TIMESTAMP is selected, the timestamp
687 (date and time) of an image is printed by image
688 commands like bootm or iminfo. This option is
689 automatically enabled when you select CFG_CMD_DATE .
692 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
693 and/or CONFIG_ISO_PARTITION
695 If IDE or SCSI support is enabled (CFG_CMD_IDE or
696 CFG_CMD_SCSI) you must configure support for at least
697 one partition type as well.
700 CONFIG_IDE_RESET_ROUTINE - this is defined in several
701 board configurations files but used nowhere!
703 CONFIG_IDE_RESET - is this is defined, IDE Reset will
704 be performed by calling the function
705 ide_set_reset(int reset)
706 which has to be defined in a board specific file
711 Set this to enable ATAPI support.
716 Set this to enable support for disks larger than 137GB
717 Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
718 Whithout these , LBA48 support uses 32bit variables and will 'only'
719 support disks up to 2.1TB.
722 When enabled, makes the IDE subsystem use 64bit sector addresses.
726 At the moment only there is only support for the
727 SYM53C8XX SCSI controller; define
728 CONFIG_SCSI_SYM53C8XX to enable it.
730 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
731 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
732 CFG_SCSI_MAX_LUN] can be adjusted to define the
733 maximum numbers of LUNs, SCSI ID's and target
735 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
737 - NETWORK Support (PCI):
739 Support for Intel 8254x gigabit chips.
742 Support for Intel 82557/82559/82559ER chips.
743 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
744 write routine for first time initialisation.
747 Support for Digital 2114x chips.
748 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
749 modem chip initialisation (KS8761/QS6611).
752 Support for National dp83815 chips.
755 Support for National dp8382[01] gigabit chips.
757 - NETWORK Support (other):
759 CONFIG_DRIVER_LAN91C96
760 Support for SMSC's LAN91C96 chips.
763 Define this to hold the physical address
764 of the LAN91C96's I/O space
766 CONFIG_LAN91C96_USE_32_BIT
767 Define this to enable 32 bit addressing
769 CONFIG_DRIVER_SMC91111
770 Support for SMSC's LAN91C111 chip
773 Define this to hold the physical address
774 of the device (I/O space)
776 CONFIG_SMC_USE_32_BIT
777 Define this if data bus is 32 bits
779 CONFIG_SMC_USE_IOFUNCS
780 Define this to use i/o functions instead of macros
781 (some hardware wont work with macros)
784 At the moment only the UHCI host controller is
785 supported (PIP405, MIP405, MPC5200); define
786 CONFIG_USB_UHCI to enable it.
787 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
788 end define CONFIG_USB_STORAGE to enable the USB
791 Supported are USB Keyboards and USB Floppy drives
793 MPC5200 USB requires additional defines:
795 for 528 MHz Clock: 0x0001bbbb
797 for differential drivers: 0x00001000
798 for single ended drivers: 0x00005000
802 The MMC controller on the Intel PXA is supported. To
803 enable this define CONFIG_MMC. The MMC can be
804 accessed from the boot prompt by mapping the device
805 to physical memory similar to flash. Command line is
806 enabled with CFG_CMD_MMC. The MMC driver also works with
807 the FAT fs. This is enabled with CFG_CMD_FAT.
809 - Journaling Flash filesystem support:
810 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
811 CONFIG_JFFS2_NAND_DEV
812 Define these for a default partition on a NAND device
814 CFG_JFFS2_FIRST_SECTOR,
815 CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
816 Define these for a default partition on a NOR device
819 Define this to create an own partition. You have to provide a
820 function struct part_info* jffs2_part_info(int part_num)
822 If you define only one JFFS2 partition you may also want to
823 #define CFG_JFFS_SINGLE_PART 1
824 to disable the command chpart. This is the default when you
825 have not defined a custom partition
830 Define this to enable standard (PC-Style) keyboard
834 Standard PC keyboard driver with US (is default) and
835 GERMAN key layout (switch via environment 'keymap=de') support.
836 Export function i8042_kbd_init, i8042_tstc and i8042_getc
837 for cfb_console. Supports cursor blinking.
842 Define this to enable video support (for output to
847 Enable Chips & Technologies 69000 Video chip
849 CONFIG_VIDEO_SMI_LYNXEM
850 Enable Silicon Motion SMI 712/710/810 Video chip. The
851 video output is selected via environment 'videoout'
852 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
855 For the CT69000 and SMI_LYNXEM drivers, videomode is
856 selected via environment 'videomode'. Two diferent ways
858 - "videomode=num" 'num' is a standard LiLo mode numbers.
859 Following standard modes are supported (* is default):
861 Colors 640x480 800x600 1024x768 1152x864 1280x1024
862 -------------+---------------------------------------------
863 8 bits | 0x301* 0x303 0x305 0x161 0x307
864 15 bits | 0x310 0x313 0x316 0x162 0x319
865 16 bits | 0x311 0x314 0x317 0x163 0x31A
866 24 bits | 0x312 0x315 0x318 ? 0x31B
867 -------------+---------------------------------------------
868 (i.e. setenv videomode 317; saveenv; reset;)
870 - "videomode=bootargs" all the video parameters are parsed
871 from the bootargs. (See drivers/videomodes.c)
874 CONFIG_VIDEO_SED13806
875 Enable Epson SED13806 driver. This driver supports 8bpp
876 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
877 or CONFIG_VIDEO_SED13806_16BPP
882 Define this to enable a custom keyboard support.
883 This simply calls drv_keyboard_init() which must be
884 defined in your board-specific files.
885 The only board using this so far is RBC823.
887 - LCD Support: CONFIG_LCD
889 Define this to enable LCD support (for output to LCD
890 display); also select one of the supported displays
891 by defining one of these:
893 CONFIG_NEC_NL6448AC33:
895 NEC NL6448AC33-18. Active, color, single scan.
897 CONFIG_NEC_NL6448BC20
899 NEC NL6448BC20-08. 6.5", 640x480.
900 Active, color, single scan.
902 CONFIG_NEC_NL6448BC33_54
904 NEC NL6448BC33-54. 10.4", 640x480.
905 Active, color, single scan.
909 Sharp 320x240. Active, color, single scan.
910 It isn't 16x9, and I am not sure what it is.
912 CONFIG_SHARP_LQ64D341
914 Sharp LQ64D341 display, 640x480.
915 Active, color, single scan.
919 HLD1045 display, 640x480.
920 Active, color, single scan.
924 Optrex CBL50840-2 NF-FW 99 22 M5
926 Hitachi LMG6912RPFC-00T
930 320x240. Black & white.
932 Normally display is black on white background; define
933 CFG_WHITE_ON_BLACK to get it inverted.
935 - Splash Screen Support: CONFIG_SPLASH_SCREEN
937 If this option is set, the environment is checked for
938 a variable "splashimage". If found, the usual display
939 of logo, copyright and system information on the LCD
940 is suppressed and the BMP image at the address
941 specified in "splashimage" is loaded instead. The
942 console is redirected to the "nulldev", too. This
943 allows for a "silent" boot where a splash screen is
944 loaded very quickly after power-on.
946 - Compression support:
949 If this option is set, support for bzip2 compressed
950 images is included. If not, only uncompressed and gzip
951 compressed images are supported.
953 NOTE: the bzip2 algorithm requires a lot of RAM, so
954 the malloc area (as defined by CFG_MALLOC_LEN) should
960 The address of PHY on MII bus.
962 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
964 The clock frequency of the MII bus
968 If this option is set, support for speed/duplex
969 detection of Gigabit PHY is included.
971 CONFIG_PHY_RESET_DELAY
973 Some PHY like Intel LXT971A need extra delay after
974 reset before any MII register access is possible.
975 For such PHY, set this option to the usec delay
976 required. (minimum 300usec for LXT971A)
978 CONFIG_PHY_CMD_DELAY (ppc4xx)
980 Some PHY like Intel LXT971A need extra delay after
981 command issued before MII status register can be read
988 Define a default value for ethernet address to use
989 for the respective ethernet interface, in case this
990 is not determined automatically.
995 Define a default value for the IP address to use for
996 the default ethernet interface, in case this is not
997 determined through e.g. bootp.
1002 Defines a default value for theIP address of a TFTP
1003 server to contact when using the "tftboot" command.
1005 - BOOTP Recovery Mode:
1006 CONFIG_BOOTP_RANDOM_DELAY
1008 If you have many targets in a network that try to
1009 boot using BOOTP, you may want to avoid that all
1010 systems send out BOOTP requests at precisely the same
1011 moment (which would happen for instance at recovery
1012 from a power failure, when all systems will try to
1013 boot, thus flooding the BOOTP server. Defining
1014 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1015 inserted before sending out BOOTP requests. The
1016 following delays are insterted then:
1018 1st BOOTP request: delay 0 ... 1 sec
1019 2nd BOOTP request: delay 0 ... 2 sec
1020 3rd BOOTP request: delay 0 ... 4 sec
1022 BOOTP requests: delay 0 ... 8 sec
1024 - DHCP Advanced Options:
1027 You can fine tune the DHCP functionality by adding
1028 these flags to the CONFIG_BOOTP_MASK define:
1030 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1031 serverip from a DHCP server, it is possible that more
1032 than one DNS serverip is offered to the client.
1033 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1034 serverip will be stored in the additional environment
1035 variable "dnsip2". The first DNS serverip is always
1036 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1037 is added to the CONFIG_BOOTP_MASK.
1039 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1040 to do a dynamic update of a DNS server. To do this, they
1041 need the hostname of the DHCP requester.
1042 If CONFIG_BOOP_SEND_HOSTNAME is added to the
1043 CONFIG_BOOTP_MASK, the content of the "hostname"
1044 environment variable is passed as option 12 to
1048 CONFIG_CDP_DEVICE_ID
1050 The device id used in CDP trigger frames.
1052 CONFIG_CDP_DEVICE_ID_PREFIX
1054 A two character string which is prefixed to the MAC address
1059 A printf format string which contains the ascii name of
1060 the port. Normally is set to "eth%d" which sets
1061 eth0 for the first ethernet, eth1 for the second etc.
1063 CONFIG_CDP_CAPABILITIES
1065 A 32bit integer which indicates the device capabilities;
1066 0x00000010 for a normal host which does not forwards.
1070 An ascii string containing the version of the software.
1074 An ascii string containing the name of the platform.
1078 A 32bit integer sent on the trigger.
1080 CONFIG_CDP_POWER_CONSUMPTION
1082 A 16bit integer containing the power consumption of the
1083 device in .1 of milliwatts.
1085 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1087 A byte containing the id of the VLAN.
1089 - Status LED: CONFIG_STATUS_LED
1091 Several configurations allow to display the current
1092 status using a LED. For instance, the LED will blink
1093 fast while running U-Boot code, stop blinking as
1094 soon as a reply to a BOOTP request was received, and
1095 start blinking slow once the Linux kernel is running
1096 (supported by a status LED driver in the Linux
1097 kernel). Defining CONFIG_STATUS_LED enables this
1100 - CAN Support: CONFIG_CAN_DRIVER
1102 Defining CONFIG_CAN_DRIVER enables CAN driver support
1103 on those systems that support this (optional)
1104 feature, like the TQM8xxL modules.
1106 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1108 These enable I2C serial bus commands. Defining either of
1109 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1110 include the appropriate I2C driver for the selected cpu.
1112 This will allow you to use i2c commands at the u-boot
1113 command line (as long as you set CFG_CMD_I2C in
1114 CONFIG_COMMANDS) and communicate with i2c based realtime
1115 clock chips. See common/cmd_i2c.c for a description of the
1116 command line interface.
1118 CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
1120 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1121 bit-banging) driver instead of CPM or similar hardware
1124 There are several other quantities that must also be
1125 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1127 In both cases you will need to define CFG_I2C_SPEED
1128 to be the frequency (in Hz) at which you wish your i2c bus
1129 to run and CFG_I2C_SLAVE to be the address of this node (ie
1130 the cpu's i2c node address).
1132 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1133 sets the cpu up as a master node and so its address should
1134 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1135 p.16-473). So, set CFG_I2C_SLAVE to 0.
1137 That's all that's required for CONFIG_HARD_I2C.
1139 If you use the software i2c interface (CONFIG_SOFT_I2C)
1140 then the following macros need to be defined (examples are
1141 from include/configs/lwmon.h):
1145 (Optional). Any commands necessary to enable the I2C
1146 controller or configure ports.
1148 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1152 (Only for MPC8260 CPU). The I/O port to use (the code
1153 assumes both bits are on the same port). Valid values
1154 are 0..3 for ports A..D.
1158 The code necessary to make the I2C data line active
1159 (driven). If the data line is open collector, this
1162 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1166 The code necessary to make the I2C data line tri-stated
1167 (inactive). If the data line is open collector, this
1170 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1174 Code that returns TRUE if the I2C data line is high,
1177 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1181 If <bit> is TRUE, sets the I2C data line high. If it
1182 is FALSE, it clears it (low).
1184 eg: #define I2C_SDA(bit) \
1185 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1186 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1190 If <bit> is TRUE, sets the I2C clock line high. If it
1191 is FALSE, it clears it (low).
1193 eg: #define I2C_SCL(bit) \
1194 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1195 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1199 This delay is invoked four times per clock cycle so this
1200 controls the rate of data transfer. The data rate thus
1201 is 1 / (I2C_DELAY * 4). Often defined to be something
1204 #define I2C_DELAY udelay(2)
1208 When a board is reset during an i2c bus transfer
1209 chips might think that the current transfer is still
1210 in progress. On some boards it is possible to access
1211 the i2c SCLK line directly, either by using the
1212 processor pin as a GPIO or by having a second pin
1213 connected to the bus. If this option is defined a
1214 custom i2c_init_board() routine in boards/xxx/board.c
1215 is run early in the boot sequence.
1217 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1219 This option enables configuration of bi_iic_fast[] flags
1220 in u-boot bd_info structure based on u-boot environment
1221 variable "i2cfast". (see also i2cfast)
1223 - SPI Support: CONFIG_SPI
1225 Enables SPI driver (so far only tested with
1226 SPI EEPROM, also an instance works with Crystal A/D and
1227 D/As on the SACSng board)
1231 Enables extended (16-bit) SPI EEPROM addressing.
1232 (symmetrical to CONFIG_I2C_X)
1236 Enables a software (bit-bang) SPI driver rather than
1237 using hardware support. This is a general purpose
1238 driver that only requires three general I/O port pins
1239 (two outputs, one input) to function. If this is
1240 defined, the board configuration must define several
1241 SPI configuration items (port pins to use, etc). For
1242 an example, see include/configs/sacsng.h.
1244 - FPGA Support: CONFIG_FPGA_COUNT
1246 Specify the number of FPGA devices to support.
1250 Used to specify the types of FPGA devices. For example,
1251 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1253 CFG_FPGA_PROG_FEEDBACK
1255 Enable printing of hash marks during FPGA configuration.
1259 Enable checks on FPGA configuration interface busy
1260 status by the configuration function. This option
1261 will require a board or device specific function to
1266 If defined, a function that provides delays in the FPGA
1267 configuration driver.
1269 CFG_FPGA_CHECK_CTRLC
1270 Allow Control-C to interrupt FPGA configuration
1272 CFG_FPGA_CHECK_ERROR
1274 Check for configuration errors during FPGA bitfile
1275 loading. For example, abort during Virtex II
1276 configuration if the INIT_B line goes low (which
1277 indicated a CRC error).
1281 Maximum time to wait for the INIT_B line to deassert
1282 after PROB_B has been deasserted during a Virtex II
1283 FPGA configuration sequence. The default time is 500
1288 Maximum time to wait for BUSY to deassert during
1289 Virtex II FPGA configuration. The default is 5 mS.
1291 CFG_FPGA_WAIT_CONFIG
1293 Time to wait after FPGA configuration. The default is
1296 - Configuration Management:
1299 If defined, this string will be added to the U-Boot
1300 version information (U_BOOT_VERSION)
1302 - Vendor Parameter Protection:
1304 U-Boot considers the values of the environment
1305 variables "serial#" (Board Serial Number) and
1306 "ethaddr" (Ethernet Address) to be parameters that
1307 are set once by the board vendor / manufacturer, and
1308 protects these variables from casual modification by
1309 the user. Once set, these variables are read-only,
1310 and write or delete attempts are rejected. You can
1311 change this behviour:
1313 If CONFIG_ENV_OVERWRITE is #defined in your config
1314 file, the write protection for vendor parameters is
1315 completely disabled. Anybody can change or delete
1318 Alternatively, if you #define _both_ CONFIG_ETHADDR
1319 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1320 ethernet address is installed in the environment,
1321 which can be changed exactly ONCE by the user. [The
1322 serial# is unaffected by this, i. e. it remains
1328 Define this variable to enable the reservation of
1329 "protected RAM", i. e. RAM which is not overwritten
1330 by U-Boot. Define CONFIG_PRAM to hold the number of
1331 kB you want to reserve for pRAM. You can overwrite
1332 this default value by defining an environment
1333 variable "pram" to the number of kB you want to
1334 reserve. Note that the board info structure will
1335 still show the full amount of RAM. If pRAM is
1336 reserved, a new environment variable "mem" will
1337 automatically be defined to hold the amount of
1338 remaining RAM in a form that can be passed as boot
1339 argument to Linux, for instance like that:
1341 setenv bootargs ... mem=\$(mem)
1344 This way you can tell Linux not to use this memory,
1345 either, which results in a memory region that will
1346 not be affected by reboots.
1348 *WARNING* If your board configuration uses automatic
1349 detection of the RAM size, you must make sure that
1350 this memory test is non-destructive. So far, the
1351 following board configurations are known to be
1354 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1355 HERMES, IP860, RPXlite, LWMON, LANTEC,
1356 PCU_E, FLAGADM, TQM8260
1361 Define this variable to stop the system in case of a
1362 fatal error, so that you have to reset it manually.
1363 This is probably NOT a good idea for an embedded
1364 system where you want to system to reboot
1365 automatically as fast as possible, but it may be
1366 useful during development since you can try to debug
1367 the conditions that lead to the situation.
1369 CONFIG_NET_RETRY_COUNT
1371 This variable defines the number of retries for
1372 network operations like ARP, RARP, TFTP, or BOOTP
1373 before giving up the operation. If not defined, a
1374 default value of 5 is used.
1376 - Command Interpreter:
1379 Enable auto completion of commands using TAB.
1383 Define this variable to enable the "hush" shell (from
1384 Busybox) as command line interpreter, thus enabling
1385 powerful command line syntax like
1386 if...then...else...fi conditionals or `&&' and '||'
1387 constructs ("shell scripts").
1389 If undefined, you get the old, much simpler behaviour
1390 with a somewhat smaller memory footprint.
1395 This defines the secondary prompt string, which is
1396 printed when the command interpreter needs more input
1397 to complete a command. Usually "> ".
1401 In the current implementation, the local variables
1402 space and global environment variables space are
1403 separated. Local variables are those you define by
1404 simply typing `name=value'. To access a local
1405 variable later on, you have write `$name' or
1406 `${name}'; to execute the contents of a variable
1407 directly type `$name' at the command prompt.
1409 Global environment variables are those you use
1410 setenv/printenv to work with. To run a command stored
1411 in such a variable, you need to use the run command,
1412 and you must not use the '$' sign to access them.
1414 To store commands and special characters in a
1415 variable, please use double quotation marks
1416 surrounding the whole text of the variable, instead
1417 of the backslashes before semicolons and special
1420 - Default Environment:
1421 CONFIG_EXTRA_ENV_SETTINGS
1423 Define this to contain any number of null terminated
1424 strings (variable = value pairs) that will be part of
1425 the default environment compiled into the boot image.
1427 For example, place something like this in your
1428 board's config file:
1430 #define CONFIG_EXTRA_ENV_SETTINGS \
1434 Warning: This method is based on knowledge about the
1435 internal format how the environment is stored by the
1436 U-Boot code. This is NOT an official, exported
1437 interface! Although it is unlikely that this format
1438 will change soon, there is no guarantee either.
1439 You better know what you are doing here.
1441 Note: overly (ab)use of the default environment is
1442 discouraged. Make sure to check other ways to preset
1443 the environment like the autoscript function or the
1446 - DataFlash Support:
1447 CONFIG_HAS_DATAFLASH
1449 Defining this option enables DataFlash features and
1450 allows to read/write in Dataflash via the standard
1453 - SystemACE Support:
1456 Adding this option adds support for Xilinx SystemACE
1457 chips attached via some sort of local bus. The address
1458 of the chip must alsh be defined in the
1459 CFG_SYSTEMACE_BASE macro. For example:
1461 #define CONFIG_SYSTEMACE
1462 #define CFG_SYSTEMACE_BASE 0xf0000000
1464 When SystemACE support is added, the "ace" device type
1465 becomes available to the fat commands, i.e. fatls.
1467 - Show boot progress:
1468 CONFIG_SHOW_BOOT_PROGRESS
1470 Defining this option allows to add some board-
1471 specific code (calling a user-provided function
1472 "show_boot_progress(int)") that enables you to show
1473 the system's boot progress on some display (for
1474 example, some LED's) on your board. At the moment,
1475 the following checkpoints are implemented:
1478 1 common/cmd_bootm.c before attempting to boot an image
1479 -1 common/cmd_bootm.c Image header has bad magic number
1480 2 common/cmd_bootm.c Image header has correct magic number
1481 -2 common/cmd_bootm.c Image header has bad checksum
1482 3 common/cmd_bootm.c Image header has correct checksum
1483 -3 common/cmd_bootm.c Image data has bad checksum
1484 4 common/cmd_bootm.c Image data has correct checksum
1485 -4 common/cmd_bootm.c Image is for unsupported architecture
1486 5 common/cmd_bootm.c Architecture check OK
1487 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1488 6 common/cmd_bootm.c Image Type check OK
1489 -6 common/cmd_bootm.c gunzip uncompression error
1490 -7 common/cmd_bootm.c Unimplemented compression type
1491 7 common/cmd_bootm.c Uncompression OK
1492 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1493 8 common/cmd_bootm.c Image Type check OK
1494 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1495 9 common/cmd_bootm.c Start initial ramdisk verification
1496 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1497 -11 common/cmd_bootm.c Ramdisk header has bad checksum
1498 10 common/cmd_bootm.c Ramdisk header is OK
1499 -12 common/cmd_bootm.c Ramdisk data has bad checksum
1500 11 common/cmd_bootm.c Ramdisk data has correct checksum
1501 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1502 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1503 13 common/cmd_bootm.c Start multifile image verification
1504 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1505 15 common/cmd_bootm.c All preparation done, transferring control to OS
1507 -30 lib_ppc/board.c Fatal error, hang the system
1508 -31 post/post.c POST test failed, detected by post_output_backlog()
1509 -32 post/post.c POST test failed, detected by post_run_single()
1511 -1 common/cmd_doc.c Bad usage of "doc" command
1512 -1 common/cmd_doc.c No boot device
1513 -1 common/cmd_doc.c Unknown Chip ID on boot device
1514 -1 common/cmd_doc.c Read Error on boot device
1515 -1 common/cmd_doc.c Image header has bad magic number
1517 -1 common/cmd_ide.c Bad usage of "ide" command
1518 -1 common/cmd_ide.c No boot device
1519 -1 common/cmd_ide.c Unknown boot device
1520 -1 common/cmd_ide.c Unknown partition table
1521 -1 common/cmd_ide.c Invalid partition type
1522 -1 common/cmd_ide.c Read Error on boot device
1523 -1 common/cmd_ide.c Image header has bad magic number
1525 -1 common/cmd_nand.c Bad usage of "nand" command
1526 -1 common/cmd_nand.c No boot device
1527 -1 common/cmd_nand.c Unknown Chip ID on boot device
1528 -1 common/cmd_nand.c Read Error on boot device
1529 -1 common/cmd_nand.c Image header has bad magic number
1531 -1 common/env_common.c Environment has a bad CRC, using default
1537 [so far only for SMDK2400 and TRAB boards]
1539 - Modem support endable:
1540 CONFIG_MODEM_SUPPORT
1542 - RTS/CTS Flow control enable:
1545 - Modem debug support:
1546 CONFIG_MODEM_SUPPORT_DEBUG
1548 Enables debugging stuff (char screen[1024], dbg())
1549 for modem support. Useful only with BDI2000.
1551 - Interrupt support (PPC):
1553 There are common interrupt_init() and timer_interrupt()
1554 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
1555 for cpu specific initialization. interrupt_init_cpu()
1556 should set decrementer_count to appropriate value. If
1557 cpu resets decrementer automatically after interrupt
1558 (ppc4xx) it should set decrementer_count to zero.
1559 timer_interrupt() calls timer_interrupt_cpu() for cpu
1560 specific handling. If board has watchdog / status_led
1561 / other_activity_monitor it works automatically from
1562 general timer_interrupt().
1566 In the target system modem support is enabled when a
1567 specific key (key combination) is pressed during
1568 power-on. Otherwise U-Boot will boot normally
1569 (autoboot). The key_pressed() fuction is called from
1570 board_init(). Currently key_pressed() is a dummy
1571 function, returning 1 and thus enabling modem
1574 If there are no modem init strings in the
1575 environment, U-Boot proceed to autoboot; the
1576 previous output (banner, info printfs) will be
1579 See also: doc/README.Modem
1582 Configuration Settings:
1583 -----------------------
1585 - CFG_LONGHELP: Defined when you want long help messages included;
1586 undefine this when you're short of memory.
1588 - CFG_PROMPT: This is what U-Boot prints on the console to
1589 prompt for user input.
1591 - CFG_CBSIZE: Buffer size for input from the Console
1593 - CFG_PBSIZE: Buffer size for Console output
1595 - CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1597 - CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1598 the application (usually a Linux kernel) when it is
1601 - CFG_BAUDRATE_TABLE:
1602 List of legal baudrate settings for this board.
1604 - CFG_CONSOLE_INFO_QUIET
1605 Suppress display of console information at boot.
1607 - CFG_CONSOLE_IS_IN_ENV
1608 If the board specific function
1609 extern int overwrite_console (void);
1610 returns 1, the stdin, stderr and stdout are switched to the
1611 serial port, else the settings in the environment are used.
1613 - CFG_CONSOLE_OVERWRITE_ROUTINE
1614 Enable the call to overwrite_console().
1616 - CFG_CONSOLE_ENV_OVERWRITE
1617 Enable overwrite of previous console environment settings.
1619 - CFG_MEMTEST_START, CFG_MEMTEST_END:
1620 Begin and End addresses of the area used by the
1624 Enable an alternate, more extensive memory test.
1626 - CFG_MEMTEST_SCRATCH:
1627 Scratch address used by the alternate memory test
1628 You only need to set this if address zero isn't writeable
1630 - CFG_TFTP_LOADADDR:
1631 Default load address for network file downloads
1633 - CFG_LOADS_BAUD_CHANGE:
1634 Enable temporary baudrate change while serial download
1637 Physical start address of SDRAM. _Must_ be 0 here.
1640 Physical start address of Motherboard I/O (if using a
1644 Physical start address of Flash memory.
1647 Physical start address of boot monitor code (set by
1648 make config files to be same as the text base address
1649 (TEXT_BASE) used when linking) - same as
1650 CFG_FLASH_BASE when booting from flash.
1653 Size of memory reserved for monitor code, used to
1654 determine _at_compile_time_ (!) if the environment is
1655 embedded within the U-Boot image, or in a separate
1659 Size of DRAM reserved for malloc() use.
1662 Maximum size of memory mapped by the startup code of
1663 the Linux kernel; all data that must be processed by
1664 the Linux kernel (bd_info, boot arguments, eventually
1665 initrd image) must be put below this limit.
1667 - CFG_MAX_FLASH_BANKS:
1668 Max number of Flash memory banks
1670 - CFG_MAX_FLASH_SECT:
1671 Max number of sectors on a Flash chip
1673 - CFG_FLASH_ERASE_TOUT:
1674 Timeout for Flash erase operations (in ms)
1676 - CFG_FLASH_WRITE_TOUT:
1677 Timeout for Flash write operations (in ms)
1679 - CFG_FLASH_LOCK_TOUT
1680 Timeout for Flash set sector lock bit operation (in ms)
1682 - CFG_FLASH_UNLOCK_TOUT
1683 Timeout for Flash clear lock bits operation (in ms)
1685 - CFG_FLASH_PROTECTION
1686 If defined, hardware flash sectors protection is used
1687 instead of U-Boot software protection.
1689 - CFG_DIRECT_FLASH_TFTP:
1691 Enable TFTP transfers directly to flash memory;
1692 without this option such a download has to be
1693 performed in two steps: (1) download to RAM, and (2)
1694 copy from RAM to flash.
1696 The two-step approach is usually more reliable, since
1697 you can check if the download worked before you erase
1698 the flash, but in some situations (when sytem RAM is
1699 too limited to allow for a tempory copy of the
1700 downloaded image) this option may be very useful.
1703 Define if the flash driver uses extra elements in the
1704 common flash structure for storing flash geometry.
1706 - CFG_FLASH_CFI_DRIVER
1707 This option also enables the building of the cfi_flash driver
1708 in the drivers directory
1710 - CFG_RX_ETH_BUFFER:
1711 Defines the number of ethernet receive buffers. On some
1712 ethernet controllers it is recommended to set this value
1713 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1714 buffers can be full shortly after enabling the interface
1715 on high ethernet traffic.
1716 Defaults to 4 if not defined.
1718 The following definitions that deal with the placement and management
1719 of environment data (variable area); in general, we support the
1720 following configurations:
1722 - CFG_ENV_IS_IN_FLASH:
1724 Define this if the environment is in flash memory.
1726 a) The environment occupies one whole flash sector, which is
1727 "embedded" in the text segment with the U-Boot code. This
1728 happens usually with "bottom boot sector" or "top boot
1729 sector" type flash chips, which have several smaller
1730 sectors at the start or the end. For instance, such a
1731 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1732 such a case you would place the environment in one of the
1733 4 kB sectors - with U-Boot code before and after it. With
1734 "top boot sector" type flash chips, you would put the
1735 environment in one of the last sectors, leaving a gap
1736 between U-Boot and the environment.
1740 Offset of environment data (variable area) to the
1741 beginning of flash memory; for instance, with bottom boot
1742 type flash chips the second sector can be used: the offset
1743 for this sector is given here.
1745 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1749 This is just another way to specify the start address of
1750 the flash sector containing the environment (instead of
1753 - CFG_ENV_SECT_SIZE:
1755 Size of the sector containing the environment.
1758 b) Sometimes flash chips have few, equal sized, BIG sectors.
1759 In such a case you don't want to spend a whole sector for
1764 If you use this in combination with CFG_ENV_IS_IN_FLASH
1765 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1766 of this flash sector for the environment. This saves
1767 memory for the RAM copy of the environment.
1769 It may also save flash memory if you decide to use this
1770 when your environment is "embedded" within U-Boot code,
1771 since then the remainder of the flash sector could be used
1772 for U-Boot code. It should be pointed out that this is
1773 STRONGLY DISCOURAGED from a robustness point of view:
1774 updating the environment in flash makes it always
1775 necessary to erase the WHOLE sector. If something goes
1776 wrong before the contents has been restored from a copy in
1777 RAM, your target system will be dead.
1779 - CFG_ENV_ADDR_REDUND
1782 These settings describe a second storage area used to hold
1783 a redundand copy of the environment data, so that there is
1784 a valid backup copy in case there is a power failure during
1785 a "saveenv" operation.
1787 BE CAREFUL! Any changes to the flash layout, and some changes to the
1788 source code will make it necessary to adapt <board>/u-boot.lds*
1792 - CFG_ENV_IS_IN_NVRAM:
1794 Define this if you have some non-volatile memory device
1795 (NVRAM, battery buffered SRAM) which you want to use for the
1801 These two #defines are used to determin the memory area you
1802 want to use for environment. It is assumed that this memory
1803 can just be read and written to, without any special
1806 BE CAREFUL! The first access to the environment happens quite early
1807 in U-Boot initalization (when we try to get the setting of for the
1808 console baudrate). You *MUST* have mappend your NVRAM area then, or
1811 Please note that even with NVRAM we still use a copy of the
1812 environment in RAM: we could work on NVRAM directly, but we want to
1813 keep settings there always unmodified except somebody uses "saveenv"
1814 to save the current settings.
1817 - CFG_ENV_IS_IN_EEPROM:
1819 Use this if you have an EEPROM or similar serial access
1820 device and a driver for it.
1825 These two #defines specify the offset and size of the
1826 environment area within the total memory of your EEPROM.
1828 - CFG_I2C_EEPROM_ADDR:
1829 If defined, specified the chip address of the EEPROM device.
1830 The default address is zero.
1832 - CFG_EEPROM_PAGE_WRITE_BITS:
1833 If defined, the number of bits used to address bytes in a
1834 single page in the EEPROM device. A 64 byte page, for example
1835 would require six bits.
1837 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1838 If defined, the number of milliseconds to delay between
1839 page writes. The default is zero milliseconds.
1841 - CFG_I2C_EEPROM_ADDR_LEN:
1842 The length in bytes of the EEPROM memory array address. Note
1843 that this is NOT the chip address length!
1845 - CFG_I2C_EEPROM_ADDR_OVERFLOW:
1846 EEPROM chips that implement "address overflow" are ones
1847 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
1848 address and the extra bits end up in the "chip address" bit
1849 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
1852 Note that we consider the length of the address field to
1853 still be one byte because the extra address bits are hidden
1854 in the chip address.
1857 The size in bytes of the EEPROM device.
1860 - CFG_ENV_IS_IN_DATAFLASH:
1862 Define this if you have a DataFlash memory device which you
1863 want to use for the environment.
1869 These three #defines specify the offset and size of the
1870 environment area within the total memory of your DataFlash placed
1871 at the specified address.
1873 - CFG_ENV_IS_IN_NAND:
1875 Define this if you have a NAND device which you want to use
1876 for the environment.
1881 These two #defines specify the offset and size of the environment
1882 area within the first NAND device.
1884 - CFG_SPI_INIT_OFFSET
1886 Defines offset to the initial SPI buffer area in DPRAM. The
1887 area is used at an early stage (ROM part) if the environment
1888 is configured to reside in the SPI EEPROM: We need a 520 byte
1889 scratch DPRAM area. It is used between the two initialization
1890 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1891 to be a good choice since it makes it far enough from the
1892 start of the data area as well as from the stack pointer.
1894 Please note that the environment is read-only as long as the monitor
1895 has been relocated to RAM and a RAM copy of the environment has been
1896 created; also, when using EEPROM you will have to use getenv_r()
1897 until then to read environment variables.
1899 The environment is protected by a CRC32 checksum. Before the monitor
1900 is relocated into RAM, as a result of a bad CRC you will be working
1901 with the compiled-in default environment - *silently*!!! [This is
1902 necessary, because the first environment variable we need is the
1903 "baudrate" setting for the console - if we have a bad CRC, we don't
1904 have any device yet where we could complain.]
1906 Note: once the monitor has been relocated, then it will complain if
1907 the default environment is used; a new CRC is computed as soon as you
1908 use the "saveenv" command to store a valid environment.
1910 - CFG_FAULT_ECHO_LINK_DOWN:
1911 Echo the inverted Ethernet link state to the fault LED.
1913 Note: If this option is active, then CFG_FAULT_MII_ADDR
1914 also needs to be defined.
1916 - CFG_FAULT_MII_ADDR:
1917 MII address of the PHY to check for the Ethernet link state.
1919 - CFG_64BIT_VSPRINTF:
1920 Makes vsprintf (and all *printf functions) support printing
1921 of 64bit values by using the L quantifier
1923 - CFG_64BIT_STRTOUL:
1924 Adds simple_strtoull that returns a 64bit value
1926 Low Level (hardware related) configuration options:
1927 ---------------------------------------------------
1929 - CFG_CACHELINE_SIZE:
1930 Cache Line Size of the CPU.
1933 Default address of the IMMR after system reset.
1935 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
1936 and RPXsuper) to be able to adjust the position of
1937 the IMMR register after a reset.
1939 - Floppy Disk Support:
1940 CFG_FDC_DRIVE_NUMBER
1942 the default drive number (default value 0)
1946 defines the spacing between fdc chipset registers
1951 defines the offset of register from address. It
1952 depends on which part of the data bus is connected to
1953 the fdc chipset. (default value 0)
1955 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1956 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1959 if CFG_FDC_HW_INIT is defined, then the function
1960 fdc_hw_init() is called at the beginning of the FDC
1961 setup. fdc_hw_init() must be provided by the board
1962 source code. It is used to make hardware dependant
1965 - CFG_IMMR: Physical address of the Internal Memory Mapped
1966 Register; DO NOT CHANGE! (11-4)
1967 [MPC8xx systems only]
1969 - CFG_INIT_RAM_ADDR:
1971 Start address of memory area that can be used for
1972 initial data and stack; please note that this must be
1973 writable memory that is working WITHOUT special
1974 initialization, i. e. you CANNOT use normal RAM which
1975 will become available only after programming the
1976 memory controller and running certain initialization
1979 U-Boot uses the following memory types:
1980 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
1981 - MPC824X: data cache
1982 - PPC4xx: data cache
1984 - CFG_GBL_DATA_OFFSET:
1986 Offset of the initial data structure in the memory
1987 area defined by CFG_INIT_RAM_ADDR. Usually
1988 CFG_GBL_DATA_OFFSET is chosen such that the initial
1989 data is located at the end of the available space
1990 (sometimes written as (CFG_INIT_RAM_END -
1991 CFG_INIT_DATA_SIZE), and the initial stack is just
1992 below that area (growing from (CFG_INIT_RAM_ADDR +
1993 CFG_GBL_DATA_OFFSET) downward.
1996 On the MPC824X (or other systems that use the data
1997 cache for initial memory) the address chosen for
1998 CFG_INIT_RAM_ADDR is basically arbitrary - it must
1999 point to an otherwise UNUSED address space between
2000 the top of RAM and the start of the PCI space.
2002 - CFG_SIUMCR: SIU Module Configuration (11-6)
2004 - CFG_SYPCR: System Protection Control (11-9)
2006 - CFG_TBSCR: Time Base Status and Control (11-26)
2008 - CFG_PISCR: Periodic Interrupt Status and Control (11-31)
2010 - CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2012 - CFG_SCCR: System Clock and reset Control Register (15-27)
2014 - CFG_OR_TIMING_SDRAM:
2018 periodic timer for refresh
2020 - CFG_DER: Debug Event Register (37-47)
2022 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
2023 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
2024 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
2026 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2028 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2029 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
2030 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
2031 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2033 - CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
2034 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
2035 Machine Mode Register and Memory Periodic Timer
2036 Prescaler definitions (SDRAM timing)
2038 - CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
2039 enable I2C microcode relocation patch (MPC8xx);
2040 define relocation offset in DPRAM [DSP2]
2042 - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
2043 enable SPI microcode relocation patch (MPC8xx);
2044 define relocation offset in DPRAM [SCC4]
2047 Use OSCM clock mode on MBX8xx board. Be careful,
2048 wrong setting might damage your board. Read
2049 doc/README.MBX before setting this variable!
2051 - CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2052 Offset of the bootmode word in DPRAM used by post
2053 (Power On Self Tests). This definition overrides
2054 #define'd default value in commproc.h resp.
2057 - CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
2058 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
2059 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
2060 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
2061 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2062 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
2063 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
2064 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
2065 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2067 - CONFIG_ETHER_ON_FEC[12]
2068 Define to enable FEC[12] on a 8xx series processor.
2070 - CONFIG_FEC[12]_PHY
2071 Define to the hardcoded PHY address which corresponds
2072 to the given FEC; i. e.
2073 #define CONFIG_FEC1_PHY 4
2074 means that the PHY with address 4 is connected to FEC1
2076 When set to -1, means to probe for first available.
2078 - CONFIG_FEC[12]_PHY_NORXERR
2079 The PHY does not have a RXERR line (RMII only).
2080 (so program the FEC to ignore it).
2083 Enable RMII mode for all FECs.
2084 Note that this is a global option, we can't
2085 have one FEC in standard MII mode and another in RMII mode.
2087 - CONFIG_CRC32_VERIFY
2088 Add a verify option to the crc32 command.
2091 => crc32 -v <address> <count> <crc32>
2093 Where address/count indicate a memory area
2094 and crc32 is the correct crc32 which the
2098 Add the "loopw" memory command. This only takes effect if
2099 the memory commands are activated globally (CFG_CMD_MEM).
2101 Building the Software:
2102 ======================
2104 Building U-Boot has been tested in native PPC environments (on a
2105 PowerBook G3 running LinuxPPC 2000) and in cross environments
2106 (running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
2109 If you are not using a native PPC environment, it is assumed that you
2110 have the GNU cross compiling tools available in your path and named
2111 with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
2112 you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
2113 the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
2116 CROSS_COMPILE = ppc_4xx-
2119 U-Boot is intended to be simple to build. After installing the
2120 sources you must configure U-Boot for one specific board type. This
2125 where "NAME_config" is the name of one of the existing
2126 configurations; the following names are supported:
2128 ADCIOP_config FPS860L_config omap730p2_config
2129 ADS860_config GEN860T_config pcu_e_config
2130 AR405_config GENIETV_config PIP405_config
2131 at91rm9200dk_config GTH_config QS823_config
2132 CANBT_config hermes_config QS850_config
2133 cmi_mpc5xx_config hymod_config QS860T_config
2134 cogent_common_config IP860_config RPXlite_config
2135 cogent_mpc8260_config IVML24_config RPXlite_DW_config
2136 cogent_mpc8xx_config IVMS8_config RPXsuper_config
2137 CPCI405_config JSE_config rsdproto_config
2138 CPCIISER4_config LANTEC_config Sandpoint8240_config
2139 csb272_config lwmon_config sbc8260_config
2140 CU824_config MBX860T_config sbc8560_33_config
2141 DUET_ADS_config MBX_config sbc8560_66_config
2142 EBONY_config MPC8260ADS_config SM850_config
2143 ELPT860_config MPC8540ADS_config SPD823TS_config
2144 ESTEEM192E_config MPC8560ADS_config stxgp3_config
2145 ETX094_config NETVIA_config SXNI855T_config
2146 FADS823_config omap1510inn_config TQM823L_config
2147 FADS850SAR_config omap1610h2_config TQM850L_config
2148 FADS860T_config omap1610inn_config TQM855L_config
2149 FPS850L_config omap5912osk_config TQM860L_config
2153 Note: for some board special configuration names may exist; check if
2154 additional information is available from the board vendor; for
2155 instance, the TQM823L systems are available without (standard)
2156 or with LCD support. You can select such additional "features"
2157 when chosing the configuration, i. e.
2160 - will configure for a plain TQM823L, i. e. no LCD support
2162 make TQM823L_LCD_config
2163 - will configure for a TQM823L with U-Boot console on LCD
2168 Finally, type "make all", and you should get some working U-Boot
2169 images ready for download to / installation on your system:
2171 - "u-boot.bin" is a raw binary image
2172 - "u-boot" is an image in ELF binary format
2173 - "u-boot.srec" is in Motorola S-Record format
2176 Please be aware that the Makefiles assume you are using GNU make, so
2177 for instance on NetBSD you might need to use "gmake" instead of
2181 If the system board that you have is not listed, then you will need
2182 to port U-Boot to your hardware platform. To do this, follow these
2185 1. Add a new configuration option for your board to the toplevel
2186 "Makefile" and to the "MAKEALL" script, using the existing
2187 entries as examples. Note that here and at many other places
2188 boards and other names are listed in alphabetical sort order. Please
2190 2. Create a new directory to hold your board specific code. Add any
2191 files you need. In your board directory, you will need at least
2192 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2193 3. Create a new configuration file "include/configs/<board>.h" for
2195 3. If you're porting U-Boot to a new CPU, then also create a new
2196 directory to hold your CPU specific code. Add any files you need.
2197 4. Run "make <board>_config" with your new name.
2198 5. Type "make", and you should get a working "u-boot.srec" file
2199 to be installed on your target system.
2200 6. Debug and solve any problems that might arise.
2201 [Of course, this last step is much harder than it sounds.]
2204 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2205 ==============================================================
2207 If you have modified U-Boot sources (for instance added a new board
2208 or support for new devices, a new CPU, etc.) you are expected to
2209 provide feedback to the other developers. The feedback normally takes
2210 the form of a "patch", i. e. a context diff against a certain (latest
2211 official or latest in CVS) version of U-Boot sources.
2213 But before you submit such a patch, please verify that your modifi-
2214 cation did not break existing code. At least make sure that *ALL* of
2215 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2216 just run the "MAKEALL" script, which will configure and build U-Boot
2217 for ALL supported system. Be warned, this will take a while. You can
2218 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2219 environment variable to the script, i. e. to use the cross tools from
2220 MontaVista's Hard Hat Linux you can type
2222 CROSS_COMPILE=ppc_8xx- MAKEALL
2224 or to build on a native PowerPC system you can type
2226 CROSS_COMPILE=' ' MAKEALL
2228 See also "U-Boot Porting Guide" below.
2231 Monitor Commands - Overview:
2232 ============================
2234 go - start application at address 'addr'
2235 run - run commands in an environment variable
2236 bootm - boot application image from memory
2237 bootp - boot image via network using BootP/TFTP protocol
2238 tftpboot- boot image via network using TFTP protocol
2239 and env variables "ipaddr" and "serverip"
2240 (and eventually "gatewayip")
2241 rarpboot- boot image via network using RARP/TFTP protocol
2242 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2243 loads - load S-Record file over serial line
2244 loadb - load binary file over serial line (kermit mode)
2246 mm - memory modify (auto-incrementing)
2247 nm - memory modify (constant address)
2248 mw - memory write (fill)
2250 cmp - memory compare
2251 crc32 - checksum calculation
2252 imd - i2c memory display
2253 imm - i2c memory modify (auto-incrementing)
2254 inm - i2c memory modify (constant address)
2255 imw - i2c memory write (fill)
2256 icrc32 - i2c checksum calculation
2257 iprobe - probe to discover valid I2C chip addresses
2258 iloop - infinite loop on address range
2259 isdram - print SDRAM configuration information
2260 sspi - SPI utility commands
2261 base - print or set address offset
2262 printenv- print environment variables
2263 setenv - set environment variables
2264 saveenv - save environment variables to persistent storage
2265 protect - enable or disable FLASH write protection
2266 erase - erase FLASH memory
2267 flinfo - print FLASH memory information
2268 bdinfo - print Board Info structure
2269 iminfo - print header information for application image
2270 coninfo - print console devices and informations
2271 ide - IDE sub-system
2272 loop - infinite loop on address range
2273 loopw - infinite write loop on address range
2274 mtest - simple RAM test
2275 icache - enable or disable instruction cache
2276 dcache - enable or disable data cache
2277 reset - Perform RESET of the CPU
2278 echo - echo args to console
2279 version - print monitor version
2280 help - print online help
2281 ? - alias for 'help'
2284 Monitor Commands - Detailed Description:
2285 ========================================
2289 For now: just type "help <command>".
2292 Environment Variables:
2293 ======================
2295 U-Boot supports user configuration using Environment Variables which
2296 can be made persistent by saving to Flash memory.
2298 Environment Variables are set using "setenv", printed using
2299 "printenv", and saved to Flash using "saveenv". Using "setenv"
2300 without a value can be used to delete a variable from the
2301 environment. As long as you don't save the environment you are
2302 working with an in-memory copy. In case the Flash area containing the
2303 environment is erased by accident, a default environment is provided.
2305 Some configuration options can be set using Environment Variables:
2307 baudrate - see CONFIG_BAUDRATE
2309 bootdelay - see CONFIG_BOOTDELAY
2311 bootcmd - see CONFIG_BOOTCOMMAND
2313 bootargs - Boot arguments when booting an RTOS image
2315 bootfile - Name of the image to load with TFTP
2317 autoload - if set to "no" (any string beginning with 'n'),
2318 "bootp" will just load perform a lookup of the
2319 configuration from the BOOTP server, but not try to
2320 load any image using TFTP
2322 autostart - if set to "yes", an image loaded using the "bootp",
2323 "rarpboot", "tftpboot" or "diskboot" commands will
2324 be automatically started (by internally calling
2327 If set to "no", a standalone image passed to the
2328 "bootm" command will be copied to the load address
2329 (and eventually uncompressed), but NOT be started.
2330 This can be used to load and uncompress arbitrary
2333 i2cfast - (PPC405GP|PPC405EP only)
2334 if set to 'y' configures Linux I2C driver for fast
2335 mode (400kHZ). This environment variable is used in
2336 initialization code. So, for changes to be effective
2337 it must be saved and board must be reset.
2339 initrd_high - restrict positioning of initrd images:
2340 If this variable is not set, initrd images will be
2341 copied to the highest possible address in RAM; this
2342 is usually what you want since it allows for
2343 maximum initrd size. If for some reason you want to
2344 make sure that the initrd image is loaded below the
2345 CFG_BOOTMAPSZ limit, you can set this environment
2346 variable to a value of "no" or "off" or "0".
2347 Alternatively, you can set it to a maximum upper
2348 address to use (U-Boot will still check that it
2349 does not overwrite the U-Boot stack and data).
2351 For instance, when you have a system with 16 MB
2352 RAM, and want to reserve 4 MB from use by Linux,
2353 you can do this by adding "mem=12M" to the value of
2354 the "bootargs" variable. However, now you must make
2355 sure that the initrd image is placed in the first
2356 12 MB as well - this can be done with
2358 setenv initrd_high 00c00000
2360 If you set initrd_high to 0xFFFFFFFF, this is an
2361 indication to U-Boot that all addresses are legal
2362 for the Linux kernel, including addresses in flash
2363 memory. In this case U-Boot will NOT COPY the
2364 ramdisk at all. This may be useful to reduce the
2365 boot time on your system, but requires that this
2366 feature is supported by your Linux kernel.
2368 ipaddr - IP address; needed for tftpboot command
2370 loadaddr - Default load address for commands like "bootp",
2371 "rarpboot", "tftpboot", "loadb" or "diskboot"
2373 loads_echo - see CONFIG_LOADS_ECHO
2375 serverip - TFTP server IP address; needed for tftpboot command
2377 bootretry - see CONFIG_BOOT_RETRY_TIME
2379 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2381 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2383 ethprime - When CONFIG_NET_MULTI is enabled controls which
2384 interface is used first.
2386 ethact - When CONFIG_NET_MULTI is enabled controls which
2387 interface is currently active. For example you
2388 can do the following
2390 => setenv ethact FEC ETHERNET
2391 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
2392 => setenv ethact SCC ETHERNET
2393 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
2395 netretry - When set to "no" each network operation will
2396 either succeed or fail without retrying.
2397 When set to "once" the network operation will
2398 fail when all the available network interfaces
2399 are tried once without success.
2400 Useful on scripts which control the retry operation
2403 vlan - When set to a value < 4095 the traffic over
2404 ethernet is encapsulated/received over 802.1q
2407 The following environment variables may be used and automatically
2408 updated by the network boot commands ("bootp" and "rarpboot"),
2409 depending the information provided by your boot server:
2411 bootfile - see above
2412 dnsip - IP address of your Domain Name Server
2413 dnsip2 - IP address of your secondary Domain Name Server
2414 gatewayip - IP address of the Gateway (Router) to use
2415 hostname - Target hostname
2417 netmask - Subnet Mask
2418 rootpath - Pathname of the root filesystem on the NFS server
2419 serverip - see above
2422 There are two special Environment Variables:
2424 serial# - contains hardware identification information such
2425 as type string and/or serial number
2426 ethaddr - Ethernet address
2428 These variables can be set only once (usually during manufacturing of
2429 the board). U-Boot refuses to delete or overwrite these variables
2430 once they have been set once.
2433 Further special Environment Variables:
2435 ver - Contains the U-Boot version string as printed
2436 with the "version" command. This variable is
2437 readonly (see CONFIG_VERSION_VARIABLE).
2440 Please note that changes to some configuration parameters may take
2441 only effect after the next boot (yes, that's just like Windoze :-).
2444 Command Line Parsing:
2445 =====================
2447 There are two different command line parsers available with U-Boot:
2448 the old "simple" one, and the much more powerful "hush" shell:
2450 Old, simple command line parser:
2451 --------------------------------
2453 - supports environment variables (through setenv / saveenv commands)
2454 - several commands on one line, separated by ';'
2455 - variable substitution using "... $(name) ..." syntax
2456 - special characters ('$', ';') can be escaped by prefixing with '\',
2458 setenv bootcmd bootm \$(address)
2459 - You can also escape text by enclosing in single apostrophes, for example:
2460 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2465 - similar to Bourne shell, with control structures like
2466 if...then...else...fi, for...do...done; while...do...done,
2467 until...do...done, ...
2468 - supports environment ("global") variables (through setenv / saveenv
2469 commands) and local shell variables (through standard shell syntax
2470 "name=value"); only environment variables can be used with "run"
2476 (1) If a command line (or an environment variable executed by a "run"
2477 command) contains several commands separated by semicolon, and
2478 one of these commands fails, then the remaining commands will be
2481 (2) If you execute several variables with one call to run (i. e.
2482 calling run with a list af variables as arguments), any failing
2483 command will cause "run" to terminate, i. e. the remaining
2484 variables are not executed.
2486 Note for Redundant Ethernet Interfaces:
2487 =======================================
2489 Some boards come with redundant ethernet interfaces; U-Boot supports
2490 such configurations and is capable of automatic selection of a
2491 "working" interface when needed. MAC assignment works as follows:
2493 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2494 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2495 "eth1addr" (=>eth1), "eth2addr", ...
2497 If the network interface stores some valid MAC address (for instance
2498 in SROM), this is used as default address if there is NO correspon-
2499 ding setting in the environment; if the corresponding environment
2500 variable is set, this overrides the settings in the card; that means:
2502 o If the SROM has a valid MAC address, and there is no address in the
2503 environment, the SROM's address is used.
2505 o If there is no valid address in the SROM, and a definition in the
2506 environment exists, then the value from the environment variable is
2509 o If both the SROM and the environment contain a MAC address, and
2510 both addresses are the same, this MAC address is used.
2512 o If both the SROM and the environment contain a MAC address, and the
2513 addresses differ, the value from the environment is used and a
2516 o If neither SROM nor the environment contain a MAC address, an error
2523 The "boot" commands of this monitor operate on "image" files which
2524 can be basicly anything, preceeded by a special header; see the
2525 definitions in include/image.h for details; basicly, the header
2526 defines the following image properties:
2528 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2529 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2530 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2531 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2532 * Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2533 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2534 Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
2535 * Compression Type (uncompressed, gzip, bzip2)
2541 The header is marked by a special Magic Number, and both the header
2542 and the data portions of the image are secured against corruption by
2549 Although U-Boot should support any OS or standalone application
2550 easily, the main focus has always been on Linux during the design of
2553 U-Boot includes many features that so far have been part of some
2554 special "boot loader" code within the Linux kernel. Also, any
2555 "initrd" images to be used are no longer part of one big Linux image;
2556 instead, kernel and "initrd" are separate images. This implementation
2557 serves several purposes:
2559 - the same features can be used for other OS or standalone
2560 applications (for instance: using compressed images to reduce the
2561 Flash memory footprint)
2563 - it becomes much easier to port new Linux kernel versions because
2564 lots of low-level, hardware dependent stuff are done by U-Boot
2566 - the same Linux kernel image can now be used with different "initrd"
2567 images; of course this also means that different kernel images can
2568 be run with the same "initrd". This makes testing easier (you don't
2569 have to build a new "zImage.initrd" Linux image when you just
2570 change a file in your "initrd"). Also, a field-upgrade of the
2571 software is easier now.
2577 Porting Linux to U-Boot based systems:
2578 ---------------------------------------
2580 U-Boot cannot save you from doing all the necessary modifications to
2581 configure the Linux device drivers for use with your target hardware
2582 (no, we don't intend to provide a full virtual machine interface to
2585 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
2587 Just make sure your machine specific header file (for instance
2588 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2589 Information structure as we define in include/u-boot.h, and make
2590 sure that your definition of IMAP_ADDR uses the same value as your
2591 U-Boot configuration in CFG_IMMR.
2594 Configuring the Linux kernel:
2595 -----------------------------
2597 No specific requirements for U-Boot. Make sure you have some root
2598 device (initial ramdisk, NFS) for your target system.
2601 Building a Linux Image:
2602 -----------------------
2604 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2605 not used. If you use recent kernel source, a new build target
2606 "uImage" will exist which automatically builds an image usable by
2607 U-Boot. Most older kernels also have support for a "pImage" target,
2608 which was introduced for our predecessor project PPCBoot and uses a
2609 100% compatible format.
2618 The "uImage" build target uses a special tool (in 'tools/mkimage') to
2619 encapsulate a compressed Linux kernel image with header information,
2620 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
2622 * build a standard "vmlinux" kernel image (in ELF binary format):
2624 * convert the kernel into a raw binary image:
2626 ${CROSS_COMPILE}-objcopy -O binary \
2627 -R .note -R .comment \
2628 -S vmlinux linux.bin
2630 * compress the binary image:
2634 * package compressed binary image for U-Boot:
2636 mkimage -A ppc -O linux -T kernel -C gzip \
2637 -a 0 -e 0 -n "Linux Kernel Image" \
2638 -d linux.bin.gz uImage
2641 The "mkimage" tool can also be used to create ramdisk images for use
2642 with U-Boot, either separated from the Linux kernel image, or
2643 combined into one file. "mkimage" encapsulates the images with a 64
2644 byte header containing information about target architecture,
2645 operating system, image type, compression method, entry points, time
2646 stamp, CRC32 checksums, etc.
2648 "mkimage" can be called in two ways: to verify existing images and
2649 print the header information, or to build new images.
2651 In the first form (with "-l" option) mkimage lists the information
2652 contained in the header of an existing U-Boot image; this includes
2653 checksum verification:
2655 tools/mkimage -l image
2656 -l ==> list image header information
2658 The second form (with "-d" option) is used to build a U-Boot image
2659 from a "data file" which is used as image payload:
2661 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2662 -n name -d data_file image
2663 -A ==> set architecture to 'arch'
2664 -O ==> set operating system to 'os'
2665 -T ==> set image type to 'type'
2666 -C ==> set compression type 'comp'
2667 -a ==> set load address to 'addr' (hex)
2668 -e ==> set entry point to 'ep' (hex)
2669 -n ==> set image name to 'name'
2670 -d ==> use image data from 'datafile'
2672 Right now, all Linux kernels for PowerPC systems use the same load
2673 address (0x00000000), but the entry point address depends on the
2676 - 2.2.x kernels have the entry point at 0x0000000C,
2677 - 2.3.x and later kernels have the entry point at 0x00000000.
2679 So a typical call to build a U-Boot image would read:
2681 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2682 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2683 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2684 > examples/uImage.TQM850L
2685 Image Name: 2.4.4 kernel for TQM850L
2686 Created: Wed Jul 19 02:34:59 2000
2687 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2688 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2689 Load Address: 0x00000000
2690 Entry Point: 0x00000000
2692 To verify the contents of the image (or check for corruption):
2694 -> tools/mkimage -l examples/uImage.TQM850L
2695 Image Name: 2.4.4 kernel for TQM850L
2696 Created: Wed Jul 19 02:34:59 2000
2697 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2698 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2699 Load Address: 0x00000000
2700 Entry Point: 0x00000000
2702 NOTE: for embedded systems where boot time is critical you can trade
2703 speed for memory and install an UNCOMPRESSED image instead: this
2704 needs more space in Flash, but boots much faster since it does not
2705 need to be uncompressed:
2707 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2708 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2709 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2710 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2711 > examples/uImage.TQM850L-uncompressed
2712 Image Name: 2.4.4 kernel for TQM850L
2713 Created: Wed Jul 19 02:34:59 2000
2714 Image Type: PowerPC Linux Kernel Image (uncompressed)
2715 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2716 Load Address: 0x00000000
2717 Entry Point: 0x00000000
2720 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2721 when your kernel is intended to use an initial ramdisk:
2723 -> tools/mkimage -n 'Simple Ramdisk Image' \
2724 > -A ppc -O linux -T ramdisk -C gzip \
2725 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2726 Image Name: Simple Ramdisk Image
2727 Created: Wed Jan 12 14:01:50 2000
2728 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2729 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2730 Load Address: 0x00000000
2731 Entry Point: 0x00000000
2734 Installing a Linux Image:
2735 -------------------------
2737 To downloading a U-Boot image over the serial (console) interface,
2738 you must convert the image to S-Record format:
2740 objcopy -I binary -O srec examples/image examples/image.srec
2742 The 'objcopy' does not understand the information in the U-Boot
2743 image header, so the resulting S-Record file will be relative to
2744 address 0x00000000. To load it to a given address, you need to
2745 specify the target address as 'offset' parameter with the 'loads'
2748 Example: install the image to address 0x40100000 (which on the
2749 TQM8xxL is in the first Flash bank):
2751 => erase 40100000 401FFFFF
2757 ## Ready for S-Record download ...
2758 ~>examples/image.srec
2759 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2761 15989 15990 15991 15992
2762 [file transfer complete]
2764 ## Start Addr = 0x00000000
2767 You can check the success of the download using the 'iminfo' command;
2768 this includes a checksum verification so you can be sure no data
2769 corruption happened:
2773 ## Checking Image at 40100000 ...
2774 Image Name: 2.2.13 for initrd on TQM850L
2775 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2776 Data Size: 335725 Bytes = 327 kB = 0 MB
2777 Load Address: 00000000
2778 Entry Point: 0000000c
2779 Verifying Checksum ... OK
2785 The "bootm" command is used to boot an application that is stored in
2786 memory (RAM or Flash). In case of a Linux kernel image, the contents
2787 of the "bootargs" environment variable is passed to the kernel as
2788 parameters. You can check and modify this variable using the
2789 "printenv" and "setenv" commands:
2792 => printenv bootargs
2793 bootargs=root=/dev/ram
2795 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2797 => printenv bootargs
2798 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2801 ## Booting Linux kernel at 40020000 ...
2802 Image Name: 2.2.13 for NFS on TQM850L
2803 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2804 Data Size: 381681 Bytes = 372 kB = 0 MB
2805 Load Address: 00000000
2806 Entry Point: 0000000c
2807 Verifying Checksum ... OK
2808 Uncompressing Kernel Image ... OK
2809 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2810 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2811 time_init: decrementer frequency = 187500000/60
2812 Calibrating delay loop... 49.77 BogoMIPS
2813 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2816 If you want to boot a Linux kernel with initial ram disk, you pass
2817 the memory addresses of both the kernel and the initrd image (PPBCOOT
2818 format!) to the "bootm" command:
2820 => imi 40100000 40200000
2822 ## Checking Image at 40100000 ...
2823 Image Name: 2.2.13 for initrd on TQM850L
2824 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2825 Data Size: 335725 Bytes = 327 kB = 0 MB
2826 Load Address: 00000000
2827 Entry Point: 0000000c
2828 Verifying Checksum ... OK
2830 ## Checking Image at 40200000 ...
2831 Image Name: Simple Ramdisk Image
2832 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2833 Data Size: 566530 Bytes = 553 kB = 0 MB
2834 Load Address: 00000000
2835 Entry Point: 00000000
2836 Verifying Checksum ... OK
2838 => bootm 40100000 40200000
2839 ## Booting Linux kernel at 40100000 ...
2840 Image Name: 2.2.13 for initrd on TQM850L
2841 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2842 Data Size: 335725 Bytes = 327 kB = 0 MB
2843 Load Address: 00000000
2844 Entry Point: 0000000c
2845 Verifying Checksum ... OK
2846 Uncompressing Kernel Image ... OK
2847 ## Loading RAMDisk Image at 40200000 ...
2848 Image Name: Simple Ramdisk Image
2849 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2850 Data Size: 566530 Bytes = 553 kB = 0 MB
2851 Load Address: 00000000
2852 Entry Point: 00000000
2853 Verifying Checksum ... OK
2854 Loading Ramdisk ... OK
2855 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2856 Boot arguments: root=/dev/ram
2857 time_init: decrementer frequency = 187500000/60
2858 Calibrating delay loop... 49.77 BogoMIPS
2860 RAMDISK: Compressed image found at block 0
2861 VFS: Mounted root (ext2 filesystem).
2865 More About U-Boot Image Types:
2866 ------------------------------
2868 U-Boot supports the following image types:
2870 "Standalone Programs" are directly runnable in the environment
2871 provided by U-Boot; it is expected that (if they behave
2872 well) you can continue to work in U-Boot after return from
2873 the Standalone Program.
2874 "OS Kernel Images" are usually images of some Embedded OS which
2875 will take over control completely. Usually these programs
2876 will install their own set of exception handlers, device
2877 drivers, set up the MMU, etc. - this means, that you cannot
2878 expect to re-enter U-Boot except by resetting the CPU.
2879 "RAMDisk Images" are more or less just data blocks, and their
2880 parameters (address, size) are passed to an OS kernel that is
2882 "Multi-File Images" contain several images, typically an OS
2883 (Linux) kernel image and one or more data images like
2884 RAMDisks. This construct is useful for instance when you want
2885 to boot over the network using BOOTP etc., where the boot
2886 server provides just a single image file, but you want to get
2887 for instance an OS kernel and a RAMDisk image.
2889 "Multi-File Images" start with a list of image sizes, each
2890 image size (in bytes) specified by an "uint32_t" in network
2891 byte order. This list is terminated by an "(uint32_t)0".
2892 Immediately after the terminating 0 follow the images, one by
2893 one, all aligned on "uint32_t" boundaries (size rounded up to
2894 a multiple of 4 bytes).
2896 "Firmware Images" are binary images containing firmware (like
2897 U-Boot or FPGA images) which usually will be programmed to
2900 "Script files" are command sequences that will be executed by
2901 U-Boot's command interpreter; this feature is especially
2902 useful when you configure U-Boot to use a real shell (hush)
2903 as command interpreter.
2909 One of the features of U-Boot is that you can dynamically load and
2910 run "standalone" applications, which can use some resources of
2911 U-Boot like console I/O functions or interrupt services.
2913 Two simple examples are included with the sources:
2918 'examples/hello_world.c' contains a small "Hello World" Demo
2919 application; it is automatically compiled when you build U-Boot.
2920 It's configured to run at address 0x00040004, so you can play with it
2924 ## Ready for S-Record download ...
2925 ~>examples/hello_world.srec
2926 1 2 3 4 5 6 7 8 9 10 11 ...
2927 [file transfer complete]
2929 ## Start Addr = 0x00040004
2931 => go 40004 Hello World! This is a test.
2932 ## Starting application at 0x00040004 ...
2943 Hit any key to exit ...
2945 ## Application terminated, rc = 0x0
2947 Another example, which demonstrates how to register a CPM interrupt
2948 handler with the U-Boot code, can be found in 'examples/timer.c'.
2949 Here, a CPM timer is set up to generate an interrupt every second.
2950 The interrupt service routine is trivial, just printing a '.'
2951 character, but this is just a demo program. The application can be
2952 controlled by the following keys:
2954 ? - print current values og the CPM Timer registers
2955 b - enable interrupts and start timer
2956 e - stop timer and disable interrupts
2957 q - quit application
2960 ## Ready for S-Record download ...
2961 ~>examples/timer.srec
2962 1 2 3 4 5 6 7 8 9 10 11 ...
2963 [file transfer complete]
2965 ## Start Addr = 0x00040004
2968 ## Starting application at 0x00040004 ...
2971 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
2974 [q, b, e, ?] Set interval 1000000 us
2977 [q, b, e, ?] ........
2978 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
2981 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
2984 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
2987 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
2989 [q, b, e, ?] ...Stopping timer
2991 [q, b, e, ?] ## Application terminated, rc = 0x0
2997 Over time, many people have reported problems when trying to use the
2998 "minicom" terminal emulation program for serial download. I (wd)
2999 consider minicom to be broken, and recommend not to use it. Under
3000 Unix, I recommend to use C-Kermit for general purpose use (and
3001 especially for kermit binary protocol download ("loadb" command), and
3002 use "cu" for S-Record download ("loads" command).
3004 Nevertheless, if you absolutely want to use it try adding this
3005 configuration to your "File transfer protocols" section:
3007 Name Program Name U/D FullScr IO-Red. Multi
3008 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3009 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3015 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3016 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3018 Building requires a cross environment; it is known to work on
3019 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3020 need gmake since the Makefiles are not compatible with BSD make).
3021 Note that the cross-powerpc package does not install include files;
3022 attempting to build U-Boot will fail because <machine/ansi.h> is
3023 missing. This file has to be installed and patched manually:
3025 # cd /usr/pkg/cross/powerpc-netbsd/include
3027 # ln -s powerpc machine
3028 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3029 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3031 Native builds *don't* work due to incompatibilities between native
3032 and U-Boot include files.
3034 Booting assumes that (the first part of) the image booted is a
3035 stage-2 loader which in turn loads and then invokes the kernel
3036 proper. Loader sources will eventually appear in the NetBSD source
3037 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3038 meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
3042 Implementation Internals:
3043 =========================
3045 The following is not intended to be a complete description of every
3046 implementation detail. However, it should help to understand the
3047 inner workings of U-Boot and make it easier to port it to custom
3051 Initial Stack, Global Data:
3052 ---------------------------
3054 The implementation of U-Boot is complicated by the fact that U-Boot
3055 starts running out of ROM (flash memory), usually without access to
3056 system RAM (because the memory controller is not initialized yet).
3057 This means that we don't have writable Data or BSS segments, and BSS
3058 is not initialized as zero. To be able to get a C environment working
3059 at all, we have to allocate at least a minimal stack. Implementation
3060 options for this are defined and restricted by the CPU used: Some CPU
3061 models provide on-chip memory (like the IMMR area on MPC8xx and
3062 MPC826x processors), on others (parts of) the data cache can be
3063 locked as (mis-) used as memory, etc.
3065 Chris Hallinan posted a good summary of these issues to the
3066 u-boot-users mailing list:
3068 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3069 From: "Chris Hallinan" <clh@net1plus.com>
3070 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3073 Correct me if I'm wrong, folks, but the way I understand it
3074 is this: Using DCACHE as initial RAM for Stack, etc, does not
3075 require any physical RAM backing up the cache. The cleverness
3076 is that the cache is being used as a temporary supply of
3077 necessary storage before the SDRAM controller is setup. It's
3078 beyond the scope of this list to expain the details, but you
3079 can see how this works by studying the cache architecture and
3080 operation in the architecture and processor-specific manuals.
3082 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3083 is another option for the system designer to use as an
3084 initial stack/ram area prior to SDRAM being available. Either
3085 option should work for you. Using CS 4 should be fine if your
3086 board designers haven't used it for something that would
3087 cause you grief during the initial boot! It is frequently not
3090 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
3091 with your processor/board/system design. The default value
3092 you will find in any recent u-boot distribution in
3093 Walnut405.h should work for you. I'd set it to a value larger
3094 than your SDRAM module. If you have a 64MB SDRAM module, set
3095 it above 400_0000. Just make sure your board has no resources
3096 that are supposed to respond to that address! That code in
3097 start.S has been around a while and should work as is when
3098 you get the config right.
3103 It is essential to remember this, since it has some impact on the C
3104 code for the initialization procedures:
3106 * Initialized global data (data segment) is read-only. Do not attempt
3109 * Do not use any unitialized global data (or implicitely initialized
3110 as zero data - BSS segment) at all - this is undefined, initiali-
3111 zation is performed later (when relocating to RAM).
3113 * Stack space is very limited. Avoid big data buffers or things like
3116 Having only the stack as writable memory limits means we cannot use
3117 normal global data to share information beween the code. But it
3118 turned out that the implementation of U-Boot can be greatly
3119 simplified by making a global data structure (gd_t) available to all
3120 functions. We could pass a pointer to this data as argument to _all_
3121 functions, but this would bloat the code. Instead we use a feature of
3122 the GCC compiler (Global Register Variables) to share the data: we
3123 place a pointer (gd) to the global data into a register which we
3124 reserve for this purpose.
3126 When choosing a register for such a purpose we are restricted by the
3127 relevant (E)ABI specifications for the current architecture, and by
3128 GCC's implementation.
3130 For PowerPC, the following registers have specific use:
3133 R3-R4: parameter passing and return values
3134 R5-R10: parameter passing
3135 R13: small data area pointer
3139 (U-Boot also uses R14 as internal GOT pointer.)
3141 ==> U-Boot will use R29 to hold a pointer to the global data
3143 Note: on PPC, we could use a static initializer (since the
3144 address of the global data structure is known at compile time),
3145 but it turned out that reserving a register results in somewhat
3146 smaller code - although the code savings are not that big (on
3147 average for all boards 752 bytes for the whole U-Boot image,
3148 624 text + 127 data).
3150 On ARM, the following registers are used:
3152 R0: function argument word/integer result
3153 R1-R3: function argument word
3155 R10: stack limit (used only if stack checking if enabled)
3156 R11: argument (frame) pointer
3157 R12: temporary workspace
3160 R15: program counter
3162 ==> U-Boot will use R8 to hold a pointer to the global data
3168 U-Boot runs in system state and uses physical addresses, i.e. the
3169 MMU is not used either for address mapping nor for memory protection.
3171 The available memory is mapped to fixed addresses using the memory
3172 controller. In this process, a contiguous block is formed for each
3173 memory type (Flash, SDRAM, SRAM), even when it consists of several
3174 physical memory banks.
3176 U-Boot is installed in the first 128 kB of the first Flash bank (on
3177 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3178 booting and sizing and initializing DRAM, the code relocates itself
3179 to the upper end of DRAM. Immediately below the U-Boot code some
3180 memory is reserved for use by malloc() [see CFG_MALLOC_LEN
3181 configuration setting]. Below that, a structure with global Board
3182 Info data is placed, followed by the stack (growing downward).
3184 Additionally, some exception handler code is copied to the low 8 kB
3185 of DRAM (0x00000000 ... 0x00001FFF).
3187 So a typical memory configuration with 16 MB of DRAM could look like
3190 0x0000 0000 Exception Vector code
3193 0x0000 2000 Free for Application Use
3199 0x00FB FF20 Monitor Stack (Growing downward)
3200 0x00FB FFAC Board Info Data and permanent copy of global data
3201 0x00FC 0000 Malloc Arena
3204 0x00FE 0000 RAM Copy of Monitor Code
3205 ... eventually: LCD or video framebuffer
3206 ... eventually: pRAM (Protected RAM - unchanged by reset)
3207 0x00FF FFFF [End of RAM]
3210 System Initialization:
3211 ----------------------
3213 In the reset configuration, U-Boot starts at the reset entry point
3214 (on most PowerPC systens at address 0x00000100). Because of the reset
3215 configuration for CS0# this is a mirror of the onboard Flash memory.
3216 To be able to re-map memory U-Boot then jumps to its link address.
3217 To be able to implement the initialization code in C, a (small!)
3218 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3219 which provide such a feature like MPC8xx or MPC8260), or in a locked
3220 part of the data cache. After that, U-Boot initializes the CPU core,
3221 the caches and the SIU.
3223 Next, all (potentially) available memory banks are mapped using a
3224 preliminary mapping. For example, we put them on 512 MB boundaries
3225 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3226 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3227 programmed for SDRAM access. Using the temporary configuration, a
3228 simple memory test is run that determines the size of the SDRAM
3231 When there is more than one SDRAM bank, and the banks are of
3232 different size, the largest is mapped first. For equal size, the first
3233 bank (CS2#) is mapped first. The first mapping is always for address
3234 0x00000000, with any additional banks following immediately to create
3235 contiguous memory starting from 0.
3237 Then, the monitor installs itself at the upper end of the SDRAM area
3238 and allocates memory for use by malloc() and for the global Board
3239 Info data; also, the exception vector code is copied to the low RAM
3240 pages, and the final stack is set up.
3242 Only after this relocation will you have a "normal" C environment;
3243 until that you are restricted in several ways, mostly because you are
3244 running from ROM, and because the code will have to be relocated to a
3248 U-Boot Porting Guide:
3249 ----------------------
3251 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3255 int main (int argc, char *argv[])
3257 sighandler_t no_more_time;
3259 signal (SIGALRM, no_more_time);
3260 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3262 if (available_money > available_manpower) {
3263 pay consultant to port U-Boot;
3267 Download latest U-Boot source;
3269 Subscribe to u-boot-users mailing list;
3272 email ("Hi, I am new to U-Boot, how do I get started?");
3276 Read the README file in the top level directory;
3277 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3278 Read the source, Luke;
3281 if (available_money > toLocalCurrency ($2500)) {
3284 Add a lot of aggravation and time;
3287 Create your own board support subdirectory;
3289 Create your own board config file;
3293 Add / modify source code;
3297 email ("Hi, I am having problems...");
3299 Send patch file to Wolfgang;
3304 void no_more_time (int sig)
3313 All contributions to U-Boot should conform to the Linux kernel
3314 coding style; see the file "Documentation/CodingStyle" in your Linux
3315 kernel source directory.
3317 Please note that U-Boot is implemented in C (and to some small parts
3318 in Assembler); no C++ is used, so please do not use C++ style
3319 comments (//) in your code.
3321 Please also stick to the following formatting rules:
3322 - remove any trailing white space
3323 - use TAB characters for indentation, not spaces
3324 - make sure NOT to use DOS '\r\n' line feeds
3325 - do not add more than 2 empty lines to source files
3326 - do not add trailing empty lines to source files
3328 Submissions which do not conform to the standards may be returned
3329 with a request to reformat the changes.
3335 Since the number of patches for U-Boot is growing, we need to
3336 establish some rules. Submissions which do not conform to these rules
3337 may be rejected, even when they contain important and valuable stuff.
3340 When you send a patch, please include the following information with
3343 * For bug fixes: a description of the bug and how your patch fixes
3344 this bug. Please try to include a way of demonstrating that the
3345 patch actually fixes something.
3347 * For new features: a description of the feature and your
3350 * A CHANGELOG entry as plaintext (separate from the patch)
3352 * For major contributions, your entry to the CREDITS file
3354 * When you add support for a new board, don't forget to add this
3355 board to the MAKEALL script, too.
3357 * If your patch adds new configuration options, don't forget to
3358 document these in the README file.
3360 * The patch itself. If you are accessing the CVS repository use "cvs
3361 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3362 version of diff does not support these options, then get the latest
3363 version of GNU diff.
3365 The current directory when running this command shall be the top
3366 level directory of the U-Boot source tree, or it's parent directory
3367 (i. e. please make sure that your patch includes sufficient
3368 directory information for the affected files).
3370 We accept patches as plain text, MIME attachments or as uuencoded
3373 * If one logical set of modifications affects or creates several
3374 files, all these changes shall be submitted in a SINGLE patch file.
3376 * Changesets that contain different, unrelated modifications shall be
3377 submitted as SEPARATE patches, one patch per changeset.
3382 * Before sending the patch, run the MAKEALL script on your patched
3383 source tree and make sure that no errors or warnings are reported
3384 for any of the boards.
3386 * Keep your modifications to the necessary minimum: A patch
3387 containing several unrelated changes or arbitrary reformats will be
3388 returned with a request to re-formatting / split it.
3390 * If you modify existing code, make sure that your new code does not
3391 add to the memory footprint of the code ;-) Small is beautiful!
3392 When adding new features, these should compile conditionally only
3393 (using #ifdef), and the resulting code with the new feature
3394 disabled must not need more memory than the old code without your